NXP Semiconductors

PCA9545D/G-T 4-Channel I2C Switch | NXP | 20-SOIC

MPN: PCA9545D/G-T ✓ Hoạt động
2.3 V to 3.6 V Vdss 20-SOIC (0.295 inch, 7.50 mm width) Package
MOQ: 1 |

PCA9545D/G-T Tóm tắt

NXP PCA9545D/G-T is a four-channel I2C bus switch with interrupt logic and reset, designed for routing a shared controller bus among multiple downstream targets. It operates from the 2.3 V to 3.6 V and 4.5 V to 5.5 V supply ranges and is packaged in a 20-pin SOIC measuring 0.295 inch, or 7.50 mm, in width. Its principal function is to isolate inactive bus segments, reduce loading, and allow multiple I2C devices to share limited address space without requiring a separate controller for every target.

An I2C switch is an interface IC that extends a two-wire serial bus by connecting or disconnecting selected downstream branches. The PCA9545D/G-T belongs to the I2C interface switch category, interface IC hierarchy, and broader digital semiconductor family. It provides four independently selectable downstream channels so embedded systems can route sensors, memory devices, display controllers, or other peripherals. The integrated interrupt logic reports selected channel activity, while reset provides a controlled way to initialize the switching and selection logic.

The primary benefits are flexible bus partitioning, reduced capacitive loading, and improved organization of multi-device systems. Each downstream path can be enabled only when required, helping isolate inactive devices. The 2.3 V to 3.6 V range supports low-voltage systems, while the 4.5 V to 5.5 V range accommodates conventional 5 V equipment. These two listed operating ranges make the device suitable for mixed-voltage interface architectures when the connected devices and level translation arrangement are appropriately designed.

Technically, the PCA9545D/G-T functions as a controlled connectivity matrix between one upstream I2C bus and four downstream branches. When a channel is disconnected, the corresponding downstream bus is prevented from loading the common bus. When enabled, transactions can propagate toward the selected target. Interrupt logic supports event-driven handling by the host processor, reducing unnecessary polling, while the reset input allows the system to restore a known selection state during startup or fault recovery.

Typical uses include sensor aggregation, industrial control modules, medical monitoring equipment, communications equipment, rack-mounted systems, and embedded consumer products. A host processor can connect several low-speed peripherals that have overlapping or conflicting addresses, then activate only the required branch. This arrangement preserves I2C wiring simplicity while controlling bus capacitance and limiting unwanted communication between disconnected targets.

PCB design should preserve short, clean I2C traces and place pull-up resistors where the bus topology requires them. Keep the reset and interrupt traces away from high-current switching nodes, provide a stable local supply rail, and verify that every enabled channel stays within the device's specified capacitance and timing limits. Confirm voltage compatibility across all attached targets before sharing a bus.

This product page combines the exact NXP ordering designation, package information, operating ranges, sourcing status, and supported interface functions with practical selection guidance, application analysis, and a parameter-focused comparison framework. It is designed to help engineers identify the correct channel count, package, voltage range, and system role before integrating the device into a new board or revising an existing multi-device I2C design.

Bộ thay thế dễ dàng lắp đặt cho PCA9545D/G-T — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.

PCA9545AD,118

✅ Drop-In
📦 20-SOIC
Matches the 4-channel I2C-switch function and 20-SOIC package; detailed electrical, temperature-grade, and interrupt differences are

📋 Tham chiếu thay thế (không có trong danh mục)

PCA9545D/G-T Tỷ lệ tối đa & tính chất điện

Product Type 4-channel I2C bus switch
Number of Channels 4 channels
Giao diện I2C
Supply Voltage Range 1 2.3 V to 3.6 V
Supply Voltage Range 2 4.5 V to 5.5 V
Hộp 20-SOIC (0.295 inch, 7.50 mm width)
Kiểu lắp đặt Surface mount
Interrupt Logic Integrated
Reset Function Integrated
Số lượng chân 20 pins

Hướng dẫn cấu hình chân PCA9545D/G-T 20-soic (0.295 inch, 7.50 mm width)

Cấu hình chân cho PCA9545D/G-T (20-soic (0.295 inch, 7.50 mm width) gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.

Bảng cấu hình chân 20-soic (0.295 inch, 7.50 mm width) cho PCA9545D/G-T

Không có dữ liệu chân cụ thể sẵn có cho PCA9545D/G-T.

Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.

Ứng dụng tiêu biểu

PCA9545D/G-T phù hợp cho 6 Áp dụngs: Multi-Sensor Acquisition, Industrial Control Module, Medical Monitoring Equipment, Communications Equipment, Embedded Consumer Device, Server Management and Storage.

🧩

Multi-Sensor Acquisition

The PCA9545D/G-T fits multi-sensor acquisition systems that place several independent I2C sensor groups behind one host-controller port. Its four selectable channels let the firmware enable only the branch associated with an active measurement, reducing unnecessary bus activity and helping isolate targets with conflicting addresses. The listed 2.3 V to 3.6 V range supports low-voltage sensing nodes, while the 4.5 V to 5.5 V range supports conventional 5 V sensors. Interrupt logic allows the controller to react to selected channel events instead of continuously polling every peripheral, and reset establishes a known state during startup. Each branch must retain appropriate pull-up resistors and remain within the maximum bus-capacitance and timing limits stated in the NXP datasheet.

🏭

Industrial Control Module

The PCA9545D/G-T is useful in an industrial control module that connects sensors, actuator controllers, memory, and communications devices through a common I2C interface. The four-channel architecture divides the peripheral network into manageable downstream segments, while channel selection helps prevent inactive devices from loading the shared bus. The 4.5 V to 5.5 V supply range suits conventional industrial interface logic where appropriate levels are required. The integrated interrupt path supports event-driven control updates, and reset supports deterministic recovery after fault handling. Robust layout should keep the bus away from high-current outputs and switching nodes, while firmware should avoid enabling channels whose capacitance would exceed the device's supported loading.

💊

Medical Monitoring Equipment

The PCA9545D/G-T can organize I2C peripherals in medical monitoring equipment that includes multiple acquisition, sensing, or storage devices. Separate channel selection helps the monitor keep idle branches disconnected, improving address-space flexibility and reducing the electrical load presented to the host controller. The device operates across the stated 2.3 V to 3.6 V and 4.5 V to 5.5 V ranges, permitting use in low-voltage and 5 V interface partitions when signal levels are compatible. Interrupt logic can notify the processor of activity on the selected branch, while reset provides a controlled initialization point. Medical designs must also satisfy their own electrical-safety, reliability, and qualification requirements beyond the device's switching function.

🌐

Communications Equipment

The PCA9545D/G-T fits communications equipment requiring several low-speed I2C peripherals to share a controller interface. A four-channel switch can separate configuration registers, status devices, memory, or monitoring components into independently enabled branches, helping avoid address conflicts and excessive loading. The 2.3 V to 3.6 V operating range supports compact low-voltage control sections, whereas the 4.5 V to 5.5 V range supports conventional 5 V logic domains. The interrupt output helps a host processor respond to relevant branch activity, and reset restores a known channel-selection state after startup or recovery. Routing and pull-up placement should follow the NXP application information to preserve signal quality over the complete bus.

📱

Embedded Consumer Device

The PCA9545D/G-T is appropriate for embedded consumer products that need to connect several I2C peripherals while conserving interface pins and reducing bus congestion. Four channels allow display, touch, storage, sensor, and auxiliary-control devices to occupy separate branches, with only the required path enabled during normal operation. Its compact 20-SOIC package supports conventional surface-mount assembly, and the two listed supply ranges cover both low-voltage and 5 V system sections. Interrupt logic supports responsive event handling, while reset simplifies initialization after power transitions. Because consumer systems may combine several devices on each branch, validate total pull-up strength, capacitance, speed, and device-specific address requirements before release.

🖥️

Server Management and Storage

The PCA9545D/G-T can be used in management or storage systems where a processor interfaces with several administrative I2C components through a common bus. Four selectable channels provide address and loading isolation among configuration controllers, sensors, memory-management devices, and other low-speed peripherals. The 4.5 V to 5.5 V range is compatible with common 5 V interface environments, while interrupt logic permits event-driven monitoring and reset supports deterministic recovery. In compact server-adjacent boards, short I2C traces and carefully placed pull-ups help maintain signal integrity. The designer should verify branch capacitance, hot-plug behavior if applicable, fault isolation, and operating-temperature requirements against the complete system specification.

What is the NXP PCA9545D/G-T?
The NXP PCA9545D/G-T is a four-channel I2C bus switch with integrated interrupt logic and reset. It routes one upstream I2C connection to four selectable downstream branches, helping isolate inactive devices and organize systems containing multiple peripheral addresses. The component is supplied in a 20-SOIC package. According to the NXP datasheet entry, its principal application is multiplexing four I2C target branches while reporting channel activity to the host controller.
What is the operating voltage of PCA9545D/G-T?
The PCA9545D/G-T supports two stated supply-voltage ranges: 2.3 V to 3.6 V and 4.5 V to 5.5 V. These ranges allow use in low-voltage and conventional 5 V interface systems. The device datasheet should be consulted for detailed operating conditions, I/O level limits, and timing parameters. Ensure that every attached I2C target and the associated pull-up arrangement remains compatible with the selected supply domain.
Where can I download the PCA9545D/G-T datasheet PDF?
The PCA9545D/G-T datasheet can be accessed through the NXP document entry and the Octopart datasheet listing on this page. The manufacturer document describes the four-channel I2C switch, interrupt logic, reset function, electrical limits, and pin configuration. Download the official PDF before assigning PCB nets, selecting pull-up resistors, or defining the system reset sequence. Use the manufacturer document as the controlling source whenever an application note and a distributor summary differ.
Where can I find the PCA9545D/G-T pinout?
The PCA9545D/G-T uses a 20-SOIC package, and its complete numbered pin assignment is shown in the NXP datasheet pin-description table. Use that table to identify the supply pins, ground pins, channel-select inputs, reset input, and interrupt output before routing the PCB. Pin names and electrical directions must be taken directly from the manufacturer document because alternate package drawings or generic bus-switch diagrams may use different labels.
What can replace the PCA9545D/G-T?
The PCA9545AD,118 is a documented NXP-family option to evaluate as a replacement because it is also described as a four-channel I2C switch in a 20-SOIC package. Its package and channel count align with the PCA9545D/G-T, but final replacement approval still requires checking the manufacturer pin table, voltage limits, timing, reset behavior, and interrupt polarity. No other pin-compatible alternatives were confirmed on this product page.
Is PCA9545D/G-T the same as PCA9545AD,118?
The PCA9545D/G-T and PCA9545AD,118 are closely related NXP four-channel I2C switch options in the 20-SOIC package, but they are not automatically interchangeable. The channel count and package match, while ordering suffixes can denote differences in temperature range, packing, or qualification. Confirm the exact ordering code, pin-level functions, operating limits, and lifecycle requirements in the NXP datasheets before treating PCA9545AD,118 as a drop-in replacement.
When should I choose PCA9545D/G-T instead of PCA9545AD,118?
Choose the PCA9545D/G-T when its exact ordering code, electrical limits, qualification, and packing meet the production requirement and the PCA9545AD,118 does not. Both options are associated with four-channel I2C switching in a 20-SOIC package, so the decision should be based on verified differences in supply range, timing, temperature grade, interrupt behavior, and lifecycle rather than the similar function descriptions. Preserve the original footprint only after completing a pin and parameter review.
Is PCA9545D/G-T suitable for multi-sensor systems?
The PCA9545D/G-T is suitable for multi-sensor systems that need one host processor to manage several I2C peripheral branches. Its four selectable channels can separate sensor groups, while interrupt logic supports event-driven servicing and reset establishes a known starting state. The device is especially helpful when several targets would otherwise share one bus segment or add excessive loading. Each branch still needs correct pull-ups, compatible logic levels, and verification against the maximum bus-capacitance limit.
What is the best NXP equivalent for PCA9545D/G-T?
The PCA9545AD,118 is the closest documented NXP-family equivalent identified for the PCA9545D/G-T because both are four-channel I2C switches in a 20-SOIC package. It remains a candidate rather than an unconditional substitute until the NXP pin descriptions, supply-voltage limits, timing characteristics, temperature grade, and interrupt implementation are compared side by side. Use the exact manufacturer ordering information for the final production decision.
Where to buy PCA9545D/G-T online?
The PCA9545D/G-T is shown by multiple authorized-channel listings and remains commercially available, with one listing showing 4,864 pieces in stock. Current commercial terms can change quickly, so use the Request a Quote form on this page to request availability, lot traceability, and a quotation for the exact PCA9545D/G-T ordering code. Specify the required quantity and packaging details in the request.
What is the price of PCA9545D/G-T?
Use the Request a Quote form on this page for the current PCA9545D/G-T quotation. The available product listings identify the part, package, and market channels but do not provide qualifying explicit quantity-break prices that can be extracted reliably. The quote form is the appropriate route for a price tied to the exact ordering suffix, quantity, delivery schedule, and traceability requirements.
What is the lead time for PCA9545D/G-T?
Current lead time for PCA9545D/G-T should be confirmed through the Request a Quote form on this page. One market listing states that its lead time is to be confirmed and shows an estimated delivery window of August 4 through August 9, but that listing can become outdated. Provide the required quantity, target delivery date, acceptable packing, and quality-document requirements so the supplier can return a current schedule.
Is PCA9545D/G-T in stock?
A product listing for PCA9545D/G-T shows 4,864 pieces in stock, indicating that the component is actively offered for procurement. Stock quantities can change rapidly and may not reflect every package or lot. Use the Request a Quote form to confirm the current quantity and delivery schedule for the exact NXP ordering code rather than relying on the listing snapshot.
What are the key specifications of PCA9545D/G-T?
The key PCA9545D/G-T specifications are four independently selectable I2C channels, integrated interrupt logic, integrated reset, two listed supply ranges of 2.3 V to 3.6 V and 4.5 V to 5.5 V, and a 20-SOIC surface-mount package measuring 0.295 inch or 7.50 mm wide. The NXP datasheet entry identifies the device as a four-channel I2C switch, making it a compact interface-controller choice for partitioning multiple downstream buses.
How should PCA9545D/G-T reset and interrupt pins be used?
Use the reset input to return the switch to a known operating state during initialization or system recovery, and use the interrupt output to inform the host that activity exists on a selected channel. These functions can simplify fault handling and reduce unnecessary polling in multi-device systems. Follow the manufacturer truth table for active levels, reset timing, and interrupt behavior so external reset architecture and host firmware match the device logic exactly.

Dữ liệu tham khảo kỹ thuật cho PCA9545D/G-T — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.

Hướng dẫn chọn lựa

Select the PCA9545D/G-T when the design requires a four-channel I2C switch in a 20-SOIC package, supports either the listed 2.3 V to 3.6 V or 4.5 V to 5.5 V supply range, and needs integrated interrupt and reset functions. It is especially useful where several I2C peripherals share a host port, addresses conflict, or inactive branches must be disconnected to control loading. The PCA9545AD,118 is the closest documented NXP-family option to evaluate, because it also appears as a four-channel I2C switch in a 20-SOIC package. Use it only after comparing the pin descriptions, timing, voltage limits, interrupt polarity, reset behavior, temperature grade, and ordering suffix. If fewer than four independently selectable branches are needed, a lower-channel-count device may simplify the design, but it would require a different footprint or pin arrangement and therefore is not a direct board-level replacement.

So sánh với các sản phẩm thay thế

Tham số Sản phẩm này PCA9545AD,118
Product Type 4-channel I2C bus switch 4-channel I2C bus switch
Brand NXP Semiconductors NXP Semiconductors
Package 20-SOIC (0.295 inch, 7.50 mm width) 20-SOIC
Number of Channels 4 channels 4 channels
Interrupt Logic Integrated Integrated
Reset Function Integrated Integrated

Bảo phân biệt quan trọng

  • Four independently routed downstream branches (vsPCA9545AD,118)
  • Explicit low-voltage and 5 V operating ranges (vsPCA9545AD,118)
  • Integrated interrupt and reset control (vsPCA9545AD,118)

Ghi chú thiết kế

Place the I2C pull-up resistors at the physical end of the relevant bus segment and keep the SDA and SCL routes short, matched, and away from switching nodes. Because the PCA9545D/G-T separates four downstream branches, calculate pull-up strength and total capacitance for the complete connected network rather than for the IC pins alone. Confirm that each enabled branch satisfies the maximum bus-capacitance and timing limits in the manufacturer datasheet.

Route the reset and interrupt nets away from high-current outputs and switching inductors because transient noise can cause false reset events or spurious interrupts. Keep the device supply connection short and decouple it locally according to the manufacturer layout guidance. Review the channel-select traces for accidental coupling to SDA or SCL, and assign a defined state to every select input during reset so the switch does not start with an unintended branch enabled.

Do not assume that identical four-channel functionality guarantees a drop-in substitution. Before replacing PCA9545D/G-T with PCA9545AD,118, compare the exact pin functions, supply limits, maximum clock frequency, propagation delay, interrupt polarity, reset timing, temperature grade, and ordering suffix. Also confirm that no two connected targets rely on an address scheme that becomes ambiguous when a channel is enabled.

Thông tin tuân thủ

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Không chì
Unknown
Không halogen
Unknown
Khoáng vật xung đột
Unknown

No specific RoHS, REACH, lead-free, halogen-free, conflict-minerals, or AEC-Q100 statement was identified for the exact PCA9545D/G-T ordering code. AEC-Q100 is not_applicable because this is an interface switch rather than an automotive-qualified component statement.

Dữ liệu được xác minh vào: 2026-11-10 — dữ liệu được xác minh và quản lý bởi đội ngũ kỹ thuật phần cứng của XAIPART

Tìm kiếm liên quan

pca9545 datasheet PCA9545D/G-T datasheet PCA9545D/G-T pinout PCA9545D/G-T datasheet pdf PCA9545D/G-T equivalent PCA9545D/G-T replacement PCA9545D/G-T price PCA9545D/G-T stock NXP PCA9545D/G-T PCA9545D/G-T 20-SOIC PCA9545D/G-T application circuit PCA9545D/G-T vs PCA9545AD,118

Các bộ phận và thuật ngữ liên quan

NXP Semiconductors PCA9545D/G-T PCA9545AD,118 4-channel I2C switch I2C bus switch I2C interface switch interface IC digital semiconductor interrupt logic reset input 2.3 V to 3.6 V supply 4.5 V to 5.5 V supply 20-SOIC SOIC package surface-mount package channel selection bus isolation bus capacitance I2C pull-up resistors multi-sensor acquisition industrial control medical monitoring equipment communications equipment
Báo giá nhanh RFQ
Hãy điền đầy đủ thông tin — đội ngũ bán hàng của chúng tôi sẽ phản hồi trong vòng 24 giờ
Mã sản phẩm Nhà sản xuất Kiểu đóng gói QTY Giá mục tiêu Phụ
✓
Báo giá đã gửi!

Chúng tôi sẽ trả lời email của bạn trong vòng 24 giờ

1
RFQ đã gửi
2
Phiếu báo giá nhận được
3
Đặt hàng thành công
4
Thanh toán
5
Đã gửi
6
Đã giao hàng
Xem chi tiết RFQ