PCA9545D/G-T 4-Channel I2C Switch | NXP | 20-SOIC
MPN: PCA9545D/G-T ✓ פעילPCA9545D/G-T סקירה
An I2C switch is an interface IC that extends a two-wire serial bus by connecting or disconnecting selected downstream branches. The PCA9545D/G-T belongs to the I2C interface switch category, interface IC hierarchy, and broader digital semiconductor family. It provides four independently selectable downstream channels so embedded systems can route sensors, memory devices, display controllers, or other peripherals. The integrated interrupt logic reports selected channel activity, while reset provides a controlled way to initialize the switching and selection logic.
The primary benefits are flexible bus partitioning, reduced capacitive loading, and improved organization of multi-device systems. Each downstream path can be enabled only when required, helping isolate inactive devices. The 2.3 V to 3.6 V range supports low-voltage systems, while the 4.5 V to 5.5 V range accommodates conventional 5 V equipment. These two listed operating ranges make the device suitable for mixed-voltage interface architectures when the connected devices and level translation arrangement are appropriately designed.
Technically, the PCA9545D/G-T functions as a controlled connectivity matrix between one upstream I2C bus and four downstream branches. When a channel is disconnected, the corresponding downstream bus is prevented from loading the common bus. When enabled, transactions can propagate toward the selected target. Interrupt logic supports event-driven handling by the host processor, reducing unnecessary polling, while the reset input allows the system to restore a known selection state during startup or fault recovery.
Typical uses include sensor aggregation, industrial control modules, medical monitoring equipment, communications equipment, rack-mounted systems, and embedded consumer products. A host processor can connect several low-speed peripherals that have overlapping or conflicting addresses, then activate only the required branch. This arrangement preserves I2C wiring simplicity while controlling bus capacitance and limiting unwanted communication between disconnected targets.
PCB design should preserve short, clean I2C traces and place pull-up resistors where the bus topology requires them. Keep the reset and interrupt traces away from high-current switching nodes, provide a stable local supply rail, and verify that every enabled channel stays within the device's specified capacitance and timing limits. Confirm voltage compatibility across all attached targets before sharing a bus.
This product page combines the exact NXP ordering designation, package information, operating ranges, sourcing status, and supported interface functions with practical selection guidance, application analysis, and a parameter-focused comparison framework. It is designed to help engineers identify the correct channel count, package, voltage range, and system role before integrating the device into a new board or revising an existing multi-device I2C design.
חלופות תחליף ישיר עבור PCA9545D/G-T — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
PCA9545AD,118
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
PCA9545D/G-T דירוגים מרביים ומאפיינים חשמליים
| Product Type | 4-channel I2C bus switch |
| Number of Channels | 4 channels |
| ממשק | I2C |
| Supply Voltage Range 1 | 2.3 V to 3.6 V |
| Supply Voltage Range 2 | 4.5 V to 5.5 V |
| מארז | 20-SOIC (0.295 inch, 7.50 mm width) |
| סוג הרכבה | Surface mount |
| Interrupt Logic | Integrated |
| Reset Function | Integrated |
| מספר פינים | 20 pins |
מדריך תצורת פינים של PCA9545D/G-T 20-soic (0.295 inch, 7.50 mm width)
תצורת פינים עבור PCA9545D/G-T (מארזת 20-soic (0.295 inch, 7.50 mm width)). מספרי פינים, פונקציות ותרשימי חיבורים מוגדרים ב-Datasheet של היצרן. יש לעיין בו לקבלת ה-footprint המדויק והנחיות הלחמה.
אין נתוני פריסת פינים מפורטים עבור PCA9545D/G-T.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
PCA9545D/G-T מתאים עבור 6 יישוםs: Multi-Sensor Acquisition, Industrial Control Module, Medical Monitoring Equipment, Communications Equipment, Embedded Consumer Device, Server Management and Storage.
Multi-Sensor Acquisition
The PCA9545D/G-T fits multi-sensor acquisition systems that place several independent I2C sensor groups behind one host-controller port. Its four selectable channels let the firmware enable only the branch associated with an active measurement, reducing unnecessary bus activity and helping isolate targets with conflicting addresses. The listed 2.3 V to 3.6 V range supports low-voltage sensing nodes, while the 4.5 V to 5.5 V range supports conventional 5 V sensors. Interrupt logic allows the controller to react to selected channel events instead of continuously polling every peripheral, and reset establishes a known state during startup. Each branch must retain appropriate pull-up resistors and remain within the maximum bus-capacitance and timing limits stated in the NXP datasheet.
Industrial Control Module
The PCA9545D/G-T is useful in an industrial control module that connects sensors, actuator controllers, memory, and communications devices through a common I2C interface. The four-channel architecture divides the peripheral network into manageable downstream segments, while channel selection helps prevent inactive devices from loading the shared bus. The 4.5 V to 5.5 V supply range suits conventional industrial interface logic where appropriate levels are required. The integrated interrupt path supports event-driven control updates, and reset supports deterministic recovery after fault handling. Robust layout should keep the bus away from high-current outputs and switching nodes, while firmware should avoid enabling channels whose capacitance would exceed the device's supported loading.
Medical Monitoring Equipment
The PCA9545D/G-T can organize I2C peripherals in medical monitoring equipment that includes multiple acquisition, sensing, or storage devices. Separate channel selection helps the monitor keep idle branches disconnected, improving address-space flexibility and reducing the electrical load presented to the host controller. The device operates across the stated 2.3 V to 3.6 V and 4.5 V to 5.5 V ranges, permitting use in low-voltage and 5 V interface partitions when signal levels are compatible. Interrupt logic can notify the processor of activity on the selected branch, while reset provides a controlled initialization point. Medical designs must also satisfy their own electrical-safety, reliability, and qualification requirements beyond the device's switching function.
Communications Equipment
The PCA9545D/G-T fits communications equipment requiring several low-speed I2C peripherals to share a controller interface. A four-channel switch can separate configuration registers, status devices, memory, or monitoring components into independently enabled branches, helping avoid address conflicts and excessive loading. The 2.3 V to 3.6 V operating range supports compact low-voltage control sections, whereas the 4.5 V to 5.5 V range supports conventional 5 V logic domains. The interrupt output helps a host processor respond to relevant branch activity, and reset restores a known channel-selection state after startup or recovery. Routing and pull-up placement should follow the NXP application information to preserve signal quality over the complete bus.
Embedded Consumer Device
The PCA9545D/G-T is appropriate for embedded consumer products that need to connect several I2C peripherals while conserving interface pins and reducing bus congestion. Four channels allow display, touch, storage, sensor, and auxiliary-control devices to occupy separate branches, with only the required path enabled during normal operation. Its compact 20-SOIC package supports conventional surface-mount assembly, and the two listed supply ranges cover both low-voltage and 5 V system sections. Interrupt logic supports responsive event handling, while reset simplifies initialization after power transitions. Because consumer systems may combine several devices on each branch, validate total pull-up strength, capacitance, speed, and device-specific address requirements before release.
Server Management and Storage
The PCA9545D/G-T can be used in management or storage systems where a processor interfaces with several administrative I2C components through a common bus. Four selectable channels provide address and loading isolation among configuration controllers, sensors, memory-management devices, and other low-speed peripherals. The 4.5 V to 5.5 V range is compatible with common 5 V interface environments, while interrupt logic permits event-driven monitoring and reset supports deterministic recovery. In compact server-adjacent boards, short I2C traces and carefully placed pull-ups help maintain signal integrity. The designer should verify branch capacitance, hot-plug behavior if applicable, fault isolation, and operating-temperature requirements against the complete system specification.
נתוני עזר הנדסיים עבור PCA9545D/G-T — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | PCA9545AD,118 |
|---|---|---|
| Product Type | 4-channel I2C bus switch | 4-channel I2C bus switch |
| Brand | NXP Semiconductors | NXP Semiconductors |
| Package | 20-SOIC (0.295 inch, 7.50 mm width) | 20-SOIC |
| Number of Channels | 4 channels | 4 channels |
| Interrupt Logic | Integrated | Integrated |
| Reset Function | Integrated | Integrated |
מבדילים עיקריים
- Four independently routed downstream branches (לעומתPCA9545AD,118)
- Explicit low-voltage and 5 V operating ranges (לעומתPCA9545AD,118)
- Integrated interrupt and reset control (לעומתPCA9545AD,118)
הערות תכנון
Place the I2C pull-up resistors at the physical end of the relevant bus segment and keep the SDA and SCL routes short, matched, and away from switching nodes. Because the PCA9545D/G-T separates four downstream branches, calculate pull-up strength and total capacitance for the complete connected network rather than for the IC pins alone. Confirm that each enabled branch satisfies the maximum bus-capacitance and timing limits in the manufacturer datasheet.
Route the reset and interrupt nets away from high-current outputs and switching inductors because transient noise can cause false reset events or spurious interrupts. Keep the device supply connection short and decouple it locally according to the manufacturer layout guidance. Review the channel-select traces for accidental coupling to SDA or SCL, and assign a defined state to every select input during reset so the switch does not start with an unintended branch enabled.
Do not assume that identical four-channel functionality guarantees a drop-in substitution. Before replacing PCA9545D/G-T with PCA9545AD,118, compare the exact pin functions, supply limits, maximum clock frequency, propagation delay, interrupt polarity, reset timing, temperature grade, and ordering suffix. Also confirm that no two connected targets rely on an address scheme that becomes ambiguous when a channel is enabled.
מידע על תאימות
No specific RoHS, REACH, lead-free, halogen-free, conflict-minerals, or AEC-Q100 statement was identified for the exact PCA9545D/G-T ordering code. AEC-Q100 is not_applicable because this is an interface switch rather than an automotive-qualified component statement.