PCA9600D - 1MHz Dual I2C Bus Buffer | NXP Semiconductors
MPN: PCA9600D ✗ Cuối đờiPCA9600D Tóm tắt
An I2C bus buffer, also called a bus repeater or bidirectional bus isolator, is an interface IC that separates a high-capacitance bus section from the controller-side bus. This separation reduces the capacitive loading seen by the master while preserving bidirectional clock and data signaling. In the power-management hierarchy, the PCA9600D is not a regulator; it is an interface IC within the broader I2C and bus-management semiconductor category.
The PCA9600D provides two buffered bus channels, a maximum operating frequency of 1 MHz, and support for bus capacitance up to 4000 pF. Its bidirectional architecture allows each channel to carry clock and data signals in either direction. The device is identified as a dual bidirectional bus buffer and is listed in SO-8 packaging, making it appropriate for compact industrial, communications, consumer, and embedded control systems.
Technically, the PCA9600 addresses the rise-time and data-integrity problems created when an I2C bus connects multiple branches or remote cable segments. Buffering one side from the other limits the capacitance directly driven by the controller. Because the buffer is non-latching, it remains transparent to normal I2C traffic rather than requiring a separate protocol or latched control state. The manufacturer describes the PCA9600 as a higher-speed alternative to the P82B96.
Typical uses include extending an I2C controller to a remote sensor or display module, isolating high-capacitance backplanes, connecting two bus segments, and supporting point-to-point links between boards with different loading conditions. In these applications, the buffer is normally placed in series with the relevant SCL or SDA conductor, with pull-up resistors placed separately on each isolated segment.
PCB implementation should keep each side of the buffer electrically distinct. Configure pull-up resistor networks independently on the controller-side and remote-side buses, maintain the device ground connection close to pin 1, and route each channel away from high-current switching nodes. Confirm rise time at the worst-case bus capacitance rather than assuming that a nominal 1 MHz operating rate applies to every wiring configuration.
This page combines the NXP product description, manufacturer datasheet link, lifecycle information, capacity and frequency characteristics, package details, and application-specific engineering guidance. It also distinguishes true drop-in ordering variants from functional alternatives, helping engineers evaluate PCB reuse, bus capacitance, voltage compatibility, and sourcing constraints before selecting a replacement.
Bộ thay thế dễ dàng lắp đặt cho PCA9600D — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với PCA9600D (cùng hình factor và footprint) — khác nhau ở Pin Count.
PCA9600D,118
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PCA9600D,112
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
PCA9600D,118
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PCA9600D Thông số kỹ thuật
| Device Type | Dual bidirectional I2C-bus buffer |
| Bidirectional Channels | 2 channels |
| Maximum Bus Frequency | 1 MHz |
| Maximum Bus Capacitance | 4000 pF |
| Điện áp cung cấp hoạt động | 2.7 V to 5.5 V |
| Khoảng nhiệt độ hoạt động | -40 °C to +85 °C |
| Package Type | 8-pin SOIC |
| Số chân | 8 pins |
| Kiểu lắp đặt | Surface mount |
| Logic Interface | Non-latching bidirectional logic interface |
| Supported Bus Topology | Point-to-point and multipoint |
| Buffer Family | PCA9600 series |
| Related Device | P82B96 |
Hướng dẫn cấu hình chân PCA9600D 8-pin soic
Cấu hình chân cho PCA9600D (8-pin soic gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho PCA9600D.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
PCA9600D phù hợp cho 6 Áp dụngs: Long-Capacitance I2C Sensor Bus, Board-to-Board I2C Isolation, Multipoint I2C Backplane, Remote Display and Control Interface, Industrial Control Module, Communications Equipment Management Bus.
Long-Capacitance I2C Sensor Bus
The PCA9600D is suitable when an I2C master must communicate with a remote group of sensors through wiring whose total capacitance approaches the supported 4000 pF limit. Buffering the remote branch prevents that capacitance from appearing directly at the controller-side bus, improving the possibility of maintaining operation at the device's 1 MHz maximum frequency. Place the buffer in series with the relevant SDA or SCL conductor and provide independent pull-up networks on both sides so each isolated segment has its own rise-time behavior.
Được đề xuất
Board-to-Board I2C Isolation
The PCA9600D can isolate an I2C connection between two circuit boards when cable length, connector capacitance, or a separate bus segment would otherwise burden the host controller. Its two independent bidirectional paths support SDA and SCL, while the non-latching logic interface preserves ordinary I2C behavior. The 4000 pF capacitance capability gives designers room for a remote branch, but signal rise time must still be checked using the actual pull-up resistance, voltage, and total wiring load.
Được đề xuất
Multipoint I2C Backplane
The PCA9600D supports multipoint arrangements where one I2C controller reaches several branches through a buffered segment. By dividing the network into a controller-side bus and a remote bus, the device reduces the capacitance that the controller must drive and helps each section retain usable rise time. Its 1 MHz maximum operating frequency accommodates relatively fast I2C traffic, although branch length, stub geometry, connector loading, and pull-up selection determine whether the complete network meets that target.
Được đề xuất
Remote Display and Control Interface
The PCA9600D can buffer an I2C link to a remote display, touch controller, or configuration device when the interconnect adds substantial capacitance. The separation reduces the load presented to the host I2C controller, while the two bidirectional channels handle both clock and data without a latched control protocol. Because the PCA9600D is an End of Life part, engineers should reserve it for maintenance and existing qualified designs or verify lifecycle availability before committing a new platform.
Được đề xuất
Industrial Control Module
The PCA9600D fits industrial control modules in which an embedded controller operates a bus across multiple connectorized daughterboards. A buffered branch can isolate accumulated connector and trace capacitance, supporting the family-level 4000 pF capability and up to 1 MHz operation. Keep the buffered sides electrically separated, return the device ground to the quiet signal ground, and validate timing at the longest supported cable and highest temperature. Any new design must account for the manufacturer's End of Life designation.
Được đề xuất
Communications Equipment Management Bus
The PCA9600D can support an I2C management bus inside communications equipment where backplane routing, connectors, and peripheral density create a capacitive load near the supported 4000 pF limit. Its dual-channel architecture provides separate paths for clock and data, and its non-latching operation requires no dedicated bus-enable protocol. Use it where the board already targets PCA9600 and has been validated for the relevant electrical timing. For new platforms, evaluate lifecycle risk alongside the device's 1 MHz capability and isolated-bus architecture.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho PCA9600D — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
Do not substitute PCA9605D or P82B96 solely because they perform related buffering functions. They may differ in channel architecture, timing, enable behavior, logic thresholds, and pin assignment. Because PCA9600D is marked End of Life, a new design should compare its electrical fit with currently supported alternatives and confirm availability through the Request a Quote form. For maintenance of an approved PCA9600D board, retaining the exact device family and package is generally lower risk than introducing a cross-family substitute.
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | PCA9600D,118 | PCA9600D,112 | PCA9600 |
|---|---|---|---|---|
| Package | 8-pin SOIC | 8-pin SO | 8-pin SO | SOIC-8 |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Device Function | Dual bidirectional bus buffer | Buffer, re-driver | Buffer, re-driver | Dual bidirectional bus buffer |
| Maximum Bus Capacitance | 4000 pF | 4000 pF | 4000 pF | 4000 pF |
| Logic Interface | Non-latching, bidirectional | Non-latching, bidirectional | Non-latching, bidirectional | Non-latching, bidirectional |
| Supported Topology | Point-to-point and multipoint | Point-to-point and multipoint | Point-to-point and multipoint | Point-to-point and multipoint |
Bảo phân biệt quan trọng
- Supports a larger capacitive I2C bus load (vsP82B96TD,118)
- Provides two independently buffered paths (vsPCA9605D,118)
- Maintains a non-latching bidirectional interface (vsPCA9525D,118)
- Direct ordering variants simplify procurement continuity (vsPCA9600 family designation)
Ghi chú thiết kế
Treat the controller side and remote side of each PCA9600D channel as separate I2C nets, and install separate pull-up resistor arrays on each side. A shared pull-up network prevents the buffer from achieving its intended capacitance-isolation benefit. Route the two sides away from each other until the protected isolation point, keep the device ground connection short, and include the connector, cable, branch, and component capacitance when checking the 4000 pF maximum load.
Validate SCL and SDA rise time at the receiver rather than relying only on the 1 MHz device rating. Rise time is set by pull-up resistance, total bus capacitance, supply voltage, leakage, and the highest operating temperature. Start with the manufacturer's recommended pull-up range, measure the worst-case branch with a high-capacitance cable and connector attached, and reduce pull-up resistance only while checking sink-current limits and signal overshoot.
Do not substitute a bus buffer based only on the SO-8 package or the phrase bidirectional buffer. Confirm the complete pin map, supply requirements, logic thresholds, enable behavior, operating frequency, and capacitive-load limit. In particular, PCA9605D and P82B96 are related in function but cannot be assumed to be pin-compatible with PCA9600D. The ordering variants PCA9600D,118 and PCA9600D,112 are preferable because they retain the target device architecture.
Place the PCA9600D directly at the transition between the controller-side and remote bus sections. Keep SDA and SCL traces short and matched where practical, route them away from switching power nodes, and provide an uninterrupted ground return beneath or adjacent to the signal path. Keep test points and long stubs away from the buffered branch because additional capacitance reduces rise time and can undermine the benefit of isolating up to 4000 pF.
Decouple the PCA9600D supply locally and connect it to the quiet ground reference used by the bus interface. Although the component is a logic buffer rather than a regulator, noisy supply or ground routing can affect switching thresholds and signal integrity. Follow the manufacturer's recommended bypass arrangement, keep the capacitor path short, and verify the device's behavior across the 2.7 V to 5.5 V operating supply range.
Thông tin tuân thủ
The manufacturer product page states that the device is End of Life, but the available product excerpts do not provide RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations.