PIC10F200-E/MC - 8-Bit Flash MCU, 384B, 4MHz, 8-DFN | Microchip
MPN: PIC10F200-E/MC ✓ Hoạt độngPIC10F200-E/MC Tóm tắt
An 8-bit microcontroller (MCU) is a small computer-on-a-chip that integrates a CPU, program memory, data memory, and I/O peripherals on a single die; in the broader component taxonomy it sits below microprocessors and above simple logic. The PIC10F200 belongs to the baseline PIC10F family from Microchip Technology - the smallest Flash-programmable 8-bit MCU line in the industry. Unlike 32-bit Cortex-M parts, 8-bit MCUs are optimized for deterministic, low-power, low-cost glue logic replacement in cost-sensitive embedded designs.
Key features include 4 I/O pins (GPIO), an 8-bit timer (TMR0) with 8-bit prescaler, an integrated 4 MHz internal precision oscillator, a power-on reset (POR) and device reset timer (DRT), and a watchdog timer (WDT) with its own on-chip RC oscillator for reliable operation without external components. The wide operating voltage range of 2.0V to 5.5V and -40C to +125C extended temperature grade support battery-powered and industrial-grade designs.
The PIC10F200-E/MC uses a Harvard RISC architecture with separate program and data buses, executed in a single instruction cycle (4 clocks) except for program branches which take two cycles. The Flash memory supports in-circuit serial programming (ICSP) via two pins (GP0/GP1), enabling firmware updates in the field without removing the device. An 8-bit wide instruction word, 12-bit program memory width, and 8-level hardware stack simplify C and assembly development with the MPLAB XC8 toolchain.
Typical applications include low-end logic replacement in consumer appliances, PWM LED dimming, fan/thermostat control in HVAC, battery chargers, and sensor signal conditioning. The 8-DFN (MC) package enables surface-mount designs under 6 mm squared - ideal where PCB area is at a premium. The wide VDD range and small footprint make this part popular as a configurable replacement for discrete 555 timer and CMOS logic circuits in production designs.
When designing with this MCU, note that only 4 of the 6 functional pins are brought out as GPIO on the 8-DFN package (the SOT-23 6-pin version exposes all 6). Place a 100 nF decoupling capacitor as close to VDD as possible, and consider the in-circuit serial programming (ICSP) pinout when laying out the PCB. The internal 4 MHz oscillator has a factory calibration of +/- 1% typical, eliminating external crystals in most cost-sensitive designs.
This page synthesizes distributor pricing, verified drop-in alternatives within the PIC10F family, and practical PCB layout/design notes that complement the manufacturer datasheet and standard distributor listings.
Bộ thay thế dễ dàng lắp đặt cho PIC10F200-E/MC — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với PIC10F200-E/MC (cùng hình factor và footprint) — khác nhau ở Package, Timers, Internal Oscillator, I/O Pins, Program Memory (Flash).
PIC10F200-I/MC
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC10F202-E/MC
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
PIC10F204-E/MC
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC10F206-E/MC
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
PIC10F220-E/MC
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC10F200-E/MC Tỷ lệ tối đa & tính chất điện
| Core Architecture | 8-bit PIC RISC |
| Program Memory (Flash) | 384 bytes (256 x 12-bit words) |
| Data RAM | 16 bytes |
| Maximum CPU Speed | 4 MHz |
| Instruction Set | 33 single-word/single-cycle instructions |
| Instruction Width | 12-bit |
| I/O Pins | 4 (bidirectional GPIO) |
| Timers | 1 x 8-bit (TMR0) with 8-bit prescaler |
| Watchdog Timer (WDT) | Yes (independent on-chip RC oscillator) |
| Internal Oscillator | 4 MHz factory calibrated (+/- 1% typical) |
| Operating Voltage (VDD) | 2.0 V to 5.5 V |
| Nhiệt độ hoạt động | -40 C to +125 C (Extended) |
| Hộp | 8-pin DFN (2x3 mm) |
| ICSP Programming | Yes (2-wire in-circuit serial programming via GP0/GP1) |
| Power-on Reset (POR) | Yes |
| Trạng thái RoHS | Compliant |
Cấu hình chân PIC10F200-E/MC
| Chân 1 | VDD — Positive supply voltage (2.0V to 5.5V) |
| Chân 2 | GP5/OSC1/CLKIN — General-purpose I/O / oscillator input / external clock input |
| Chân 3 | GP4/OSC2/CLKOUT — General-purpose I/O / oscillator output / clock output |
| Chân 4 | GP3/MCLR/VPP — General-purpose input only / Master Clear reset / programming voltage |
| Chân 5 | VSS — Ground reference |
| Chân 6 | GP0/ICSPDAT — General-purpose I/O / ICSP data |
| Chân 7 | GP1/ICSPCLK — General-purpose I/O / ICSP clock |
| Chân 8 | GP2/T0CKI — General-purpose I/O / Timer 0 clock input |
Ứng dụng tiêu biểu
PIC10F200-E/MC phù hợp cho 6 Áp dụngs: Discrete Logic Replacement, LED Driver / PWM Dimming, Battery-Powered Sensor Node, Fan / Motor Speed Control, Toy / Consumer Electronics Controller, Automotive Subsystem Controller.
Discrete Logic Replacement
The PIC10F200-E/MC replaces 2-4 discrete 555 timer or CMOS logic ICs (74HC00 family) in cost-sensitive designs. Its 384-byte Flash, 4 MHz execution, and 4 GPIO are sufficient to implement monostable/astable timing, latch functions, and simple state machines on a 2x3 mm footprint. With only $0.52 per unit at 1k quantity, it often costs less than the discrete parts it replaces, while adding firmware flexibility. Designers gain field-upgradeable behavior via in-circuit serial programming (ICSP) using just pins GP0/GP1, eliminating rework when logic needs to change.
Được đề xuất
LED Driver / PWM Dimming
The PIC10F200-E/MC's TMR0 8-bit timer with prescaler generates accurate PWM for LED brightness control, fading, and color mixing. Software PWM at 4 MHz easily achieves 8-bit PWM resolution at 1 kHz update rate - sufficient for human-perceptible smooth dimming. Its 2.0V-5.5V VDD range allows direct drive of LEDs from single-cell Li-ion or 3x AA supplies without level shifters. The wide -40 C to +125 C operating range suits automotive interior lighting and industrial indicator applications.
Được đề xuất
Battery-Powered Sensor Node
The PIC10F200-E/MC's low current draw makes it ideal for battery-powered sensor nodes such as thermostats, smoke detectors, and remote controls. At 4 MHz the core draws under 1 mA active, and sleep current drops to microamp levels for multi-year battery life on 2x AA cells. Its 4 GPIO pins can directly interface thermistors, photo-diodes, or simple switches without external ADC (using TMR0 with internal comparator on the PIC10F204).
Được đề xuất
Fan / Motor Speed Control
The PIC10F200-E/MC implements closed-loop fan or small DC motor speed control via TMR0-based PWM and software PI control. With a 4 MHz clock and 8-bit timer resolution, PWM frequencies up to 62.5 kHz are possible - above the audible range - eliminating motor whine. The internal 4 MHz oscillator with +/- 1% accuracy eliminates external timing components, reducing BOM cost and PCB area. Extended -40 C to +125 C temperature operation supports under-hood automotive and industrial motor applications.
Được đề xuất
Toy / Consumer Electronics Controller
The PIC10F200-E/MC's tiny 2x3 mm DFN footprint and sub-$0.50 unit price make it ideal for toys, novelties, and consumer gadgets where every millimeter and every cent counts. Its 384-byte Flash supports multi-mode sound playback, button debouncing, and motor sequencing. RISC 33-instruction simplicity lets junior engineers program complex behaviors in assembly in days. The 8-pin DFN also fits inside button cells for ultra-compact form factors.
Được đề xuất
Automotive Subsystem Controller
The PIC10F200-E/MC's -40 C to +125 C extended temperature grade and 5.5V VDD tolerance suit non-safety automotive subsystems like accessory lighting, seat controllers, and HVAC auxiliaries. Its 8-DFN package fits within tight under-dash modules, and the ICSP programming allows firmware updates during end-of-line manufacturing. Note: This part is NOT AEC-Q100 qualified - for safety-critical automotive functions, design with PIC16F or PIC18F AEC-Q100 qualified alternatives.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho PIC10F200-E/MC — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | PIC10F200-I/MC | PIC10F202-E/MC | PIC10F204-E/MC | PIC10F206-E/MC | PIC10F220-E/MC |
|---|---|---|---|---|---|---|
| Package | 8-DFN (2x3 mm) | 8-DFN (2x3 mm) | 8-DFN (2x3 mm) | 8-DFN (2x3 mm) | 8-DFN (2x3 mm) | 8-DFN (2x3 mm) |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Flash Program Memory | 384 bytes (256 x 12-bit) | 384 bytes | 512 bytes | 512 bytes | 896 bytes | 384 bytes |
| Data RAM | 16 bytes | 16 bytes | 24 bytes | 24 bytes | 24 bytes | 16 bytes |
| Maximum Clock Speed | 4 MHz | 4 MHz | 4 MHz | 4 MHz | 4 MHz | 4 MHz |
| GPIO Pins | 4 | 4 | 4 | 4 | 4 | 4 |
| Analog Peripherals | None | None | Comparator | Comparator + 8-bit ADC | Comparator + 8-bit ADC | Comparator + 8-bit ADC |
| Operating Temperature | -40 C to +125 C (Extended) | -40 C to +85 C (Industrial) | -40 C to +125 C | -40 C to +125 C | -40 C to +125 C | -40 C to +125 C |
Bảo phân biệt quan trọng
- Lowest cost Flash PIC with 8-DFN package (vsPIC10F200-E/P)
- Extended temperature range (vsPIC10F200-I/MC)
- Baseline minimal-cost Flash MCU (vsPIC12F629-I/P)
Ghi chú thiết kế
Place a 100 nF decoupling capacitor as close as possible to the VDD pin (pin 1) of the PIC10F200-E/MC. For battery-powered designs, add a 10 uF bulk capacitor at the power source. The MCU draws under 1 mA active at 4 MHz and microamp-level current in sleep - well-suited for 2x AA or coin-cell operation. The POR (power-on reset) and DRT (device reset timer) handle startup reliably down to 2.0V VDD.
The 8-DFN (2x3 mm) package has an exposed thermal pad on the underside for mechanical integrity - ensure the PCB land pattern includes at least 50% thermal via array under the pad to the ground plane for reliable reflow soldering. Keep ICSP pins GP0 (pin 6) and GP1 (pin 7) accessible during layout - either route to test pads or expose via header for in-circuit programming.
Pin GP3 is input-only - using it as output will damage the device. MCLR (pin 4) must be tied to VDD through a 10 kohm resistor for normal operation, or directly to VDD if no external reset is needed. The internal 4 MHz oscillator accuracy is +/- 1% typical at 25 C but degrades at temperature extremes - for UART or precision timing applications across the full -40 C to +125 C range, calibrate the OSCCAL register against a known reference.
Thông tin tuân thủ
RoHS compliant per Microchip product page. NOT AEC-Q100 qualified - for AEC-Q100 automotive applications use PIC16F or PIC18F series.
