PIC16C77-10E/PT - 8-Bit 10MHz OTP MCU 14KB Flash 44-TQFP | Microchip
MPN: PIC16C77-10E/PT ✗ Cuối đờiPIC16C77-10E/PT Tóm tắt
An MCU (microcontroller unit) is a single-chip computer containing a CPU core, non-volatile program memory, working RAM, peripherals, and I/O - essentially a complete compute subsystem on one IC. The 8-bit PIC16C family targets low-cost, deterministic, low-power embedded applications where simple register-level programming, predictable interrupt latency, and small footprint outweigh the throughput advantages of 16/32-bit cores. The PIC16C77 is the upper-memory sibling of the PIC16C76 within the mid-range PIC16C6X/7X family, adding 8K words of code space and an extended instruction set.
Key features of the PIC16C77-10E/PT include a wide operating voltage range of 2.5V to 6.0V, 25 mA source/sink current per I/O to directly drive LEDs or small relays, low-power consumption (typical <2 mA active at 5V/4MHz), and three temperature grades. The "-10E" suffix indicates 10MHz maximum frequency and the Extended (-40C to +125C) temperature range. The 44-TQFP (PT) package variant also offers 40-pin PDIP (P) and 44-pin PLCC (L) options for through-hole and socketed designs.
Architecturally, the PIC16C77 uses a Harvard RISC core with separate program and data buses, allowing simultaneous instruction fetch and data access. The 14-bit wide instruction word supports single-word single-cycle instructions with 200 ns minimum cycle time at 10MHz. The on-chip peripherals are mapped into a 368-byte register file and 8-level hardware stack, and an integrated power-on reset / brown-out detector / watchdog timer trio provides unsupervised operation. The synchronous serial port can be configured as SPI master/slave or I2C, while the AUSART delivers asynchronous or synchronous serial communication.
Typical applications include industrial automation controllers, sensor signal conditioning with on-chip ADC, motor and lighting control with PWM, HVAC user-interface panels, automotive body and accessory ECUs, and consumer appliance controllers. Its 33 I/O lines comfortably support mid-sized user interfaces with keypads, displays, and indicator LEDs.
When designing with the PIC16C77-10E/PT, the OTP memory constraint is critical: program code must be fully verified before production programming because OTP cannot be erased. For prototype or field-updatable designs, use the flash-based PIC16F77 drop-in successor. Always include decoupling capacitors within 10 mm of the VDD/VSS pins, and respect the 6.0V absolute-maximum supply.
This page synthesizes distributor pricing, drop-in alternatives, application notes, and design considerations not consolidated in the manufacturer datasheet.
Bộ thay thế dễ dàng lắp đặt cho PIC16C77-10E/PT — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với PIC16C77-10E/PT (cùng hình factor và footprint) — khác nhau ở Timers, Core Architecture, Serial Interfaces, Package, Program Memory Type.
PIC16C77-10/PT
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →PIC16C77-04I/PT
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
PIC16F77-I/PT
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →PIC16F877A-I/PT
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →PIC16C77-20E/PT
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →PIC16C77-10E/PT Tỷ lệ tối đa & tính chất điện
| Core Architecture | PIC 8-bit Harvard RISC |
| Series | PIC® 16C |
| Program Memory Type | OTP (One-Time Programmable) |
| Program Memory Size | 14 KB (8K x 14) |
| RAM Size | 368 B |
| EEPROM Data Memory | None |
| Maximum CPU Frequency | 10 MHz |
| Instruction Cycle Time | 200 ns |
| Operating Voltage Range | 2.5 V to 6.0 V |
| I/O Pins | 33 |
| ADC | 8 channels, 8-bit |
| Timers | 2 x 8-bit, 1 x 16-bit (CCP) |
| Communication Interfaces | AUSART, SPI, I2C (SSP) |
| I/O Sink/Source Current | 25 mA / 25 mA |
| Nhiệt độ hoạt động | -40 C to +125 C (Extended, "E" suffix) |
| Hộp | 44-TQFP (10x10 mm), "PT" suffix |
| Kiểu lắp đặt | Surface Mount |
| Packaging | Tube |
Cấu hình chân PIC16C77-10E/PT
| Chân 1 | RA0/AN0 — PORTA bit 0 / analog input 0 |
| Chân 2 | RA1/AN1 — PORTA bit 1 / analog input 1 |
| Chân 3 | RA2/AN2 — PORTA bit 2 / analog input 2 |
| Chân 4 | RA3/AN3/VREF — PORTA bit 3 / analog input 3 / VREF+ |
| Chân 5 | RA4/T0CKI — PORTA bit 4 / Timer0 clock input |
| Chân 6 | RA5/AN4/SS — PORTA bit 5 / analog input 4 / SPI slave select |
| Chân 7 | RE0/RD — PORTE bit 0 / parallel slave port read |
| Chân 8 | RE1/WR — PORTE bit 1 / parallel slave port write |
| Chân 9 | RE2/CS — PORTE bit 2 / parallel slave port chip select |
| Chân 10 | VDD — Positive digital supply (2.5-6.0 V) |
| Chân 11 | VSS — Digital ground |
| Chân 12 | OSC1/CLKIN — Crystal oscillator input / external clock in |
| Chân 13 | OSC2/CLKOUT — Crystal oscillator output / clock out |
| Chân 14 | RC0/T1OSO/T1CKI — PORTC bit 0 / Timer1 oscillator out / Timer1 clock in |
| Chân 15 | RC1/T1OSI/CCP2 — PORTC bit 1 / Timer1 oscillator in / CCP2 |
| Chân 16 | RC2/CCP1 — PORTC bit 2 / Capture/Compare/PWM 1 |
| Chân 17 | RC3/SCK/SCL — PORTC bit 3 / SPI clock / I2C clock |
| Chân 18 | RD0/PSP0 — PORTD bit 0 / parallel slave port bit 0 |
| Chân 19 | RD1/PSP1 — PORTD bit 1 / parallel slave port bit 1 |
| Chân 20 | RD2/PSP2 — PORTD bit 2 / parallel slave port bit 2 |
| Chân 21 | RD3/PSP3 — PORTD bit 3 / parallel slave port bit 3 |
| Chân 22 | RC4/SDI/SDA — PORTC bit 4 / SPI data in / I2C data |
| Chân 23 | RC5/SDO — PORTC bit 5 / SPI data out |
| Chân 24 | RC6/TX/CK — PORTC bit 6 / AUSART TX / clock |
| Chân 25 | RC7/RX/DT — PORTC bit 7 / AUSART RX / data |
| Chân 26 | RD4/PSP4 — PORTD bit 4 / parallel slave port bit 4 |
| Chân 27 | RD5/PSP5 — PORTD bit 5 / parallel slave port bit 5 |
| Chân 28 | RD6/PSP6 — PORTD bit 6 / parallel slave port bit 6 |
| Chân 29 | RD7/PSP7 — PORTD bit 7 / parallel slave port bit 7 |
| Chân 30 | AVSS — Analog ground |
| Chân 31 | AVDD — Analog positive supply |
| Chân 32 | VSS — Digital ground |
| Chân 33 | VDD — Positive digital supply (2.5-6.0 V) |
| Chân 34 | RB0/INT — PORTB bit 0 / external interrupt |
| Chân 35 | RB1 — PORTB bit 1 |
| Chân 36 | RB2 — PORTB bit 2 |
| Chân 37 | RB3 — PORTB bit 3 |
| Chân 38 | RB4 — PORTB bit 4 |
| Chân 39 | RB5 — PORTB bit 5 |
| Chân 40 | RB6/PGC — PORTB bit 6 / ICSP clock |
| Chân 41 | RB7/PGD — PORTB bit 7 / ICSP data |
| Chân 42 | RC0 — PORTC bit 0 (alternate location, dup) |
| Chân 43 | MCLR/VPP — Master clear reset (active low) / programming voltage |
| Chân 44 | VSS — Digital ground |
Ứng dụng tiêu biểu
PIC16C77-10E/PT phù hợp cho 6 Áp dụngs: Industrial Automation Controllers, Automotive Body and Accessory ECUs, HVAC Control Panels, Sensor Signal Conditioning and Data Acquisition, Motor Control (PWM and Stepper Drivers), Consumer Appliance Controllers.
Industrial Automation Controllers
The PIC16C77-10E/PT's 33 I/O lines, 8-channel 8-bit ADC, three timers, and 25 mA source/sink drive make it well suited to industrial PLCs, sensor-interface modules, and discrete control boards. Its 14 KB OTP program memory accommodates ladder-style logic and serial-protocol stacks, while the wide 2.5-6.0 V supply and -40C to +125C extended temperature range let it survive 24 V-conditioned industrial rails and factory-floor thermal stress. Place 100 nF decoupling caps within 10 mm of VDD/VSS, and use the AUSART for Modbus RTU over RS-485 transceivers.
Được đề xuất
Automotive Body and Accessory ECUs
Automotive body controllers, lighting modules, and accessory ECUs benefit from the PIC16C77-10E/PT's 25 mA I/O drive (enough to switch small relays and LED arrays directly), 8-channel ADC for battery-voltage and switch-state monitoring, and extended -40C to +125C operating range. The PWM-capable 16-bit CCP timer drives LED dimming and motor speed control without additional driver ICs, while the SSP supports SPI/I2C for sensor peripherals. For new automotive designs, prefer the AEC-Q100-qualified PIC16F877A-I/PT instead.
Được đề xuất
HVAC Control Panels
HVAC user-interface panels and thermostat controllers use the PIC16C77-10E/PT to scan keypads, drive LCD/LED displays, and read temperature/humidity sensors via the on-chip 8-channel 8-bit ADC. The 14 KB OTP memory holds UI state machines and PID control loops, while three timers handle PWM fan-speed outputs, scheduling, and debounce. The AUSART links the panel to a central HVAC controller for zone coordination, and the wide 2.5-6.0 V supply tolerance simplifies 5 V and 3.3 V mixed-rail designs.
Được đề xuất
Sensor Signal Conditioning and Data Acquisition
Multi-channel sensor-interface modules use the PIC16C77-10E/PT's 8-channel 8-bit ADC plus 33 I/O to read thermocouples, flow meters, pressure transducers, and switch contacts. The AUSART streams conditioned data to a host PLC or PC, while the SSP interfaces with SPI-based digital sensors. With 368 bytes of RAM and 14 KB of OTP program memory, the device holds calibration tables and linearization routines. Brown-out reset and watchdog timer provide unsupervised field operation.
Được đề xuất
Motor Control (PWM and Stepper Drivers)
Brushless DC, brushed DC, and small stepper-motor control loops fit within the PIC16C77-10E/PT's PIC16C core, leveraging the 16-bit CCP module for PWM generation and the 8-bit timers for commutation timing. The 25 mA I/O source/sink capability directly drives opto-isolated gate drivers, while the SSP synchronizes with encoder feedback over SPI. With 10 MHz CPU, the 200 ns instruction cycle supports 5-10 kHz commutation rates typical of small appliance and pump motors.
Được đề xuất
Consumer Appliance Controllers
Washing machines, dishwashers, microwave ovens, and small kitchen appliances integrate the PIC16C77-10E/PT for cycle control, user-interface handling, and safety monitoring. The wide 2.5-6.0 V supply accommodates rectified mains-derived rails, while the 8-channel ADC reads temperature, water level, and motor current sensors. OTP-based code locks in firmware against accidental field changes, and 33 I/O lines drive seven-segment displays, keypads, indicator LEDs, and TRIAC firing circuits through optocouplers.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho PIC16C77-10E/PT — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | PIC16C77-10/PT | PIC16C77-04I/PT | PIC16F77-I/PT | PIC16F877A-I/PT | PIC16C77-20E/PT |
|---|---|---|---|---|---|---|
| Package | 44-TQFP (PT) | 44-TQFP (PT) - same | 44-TQFP (PT) - same | 44-TQFP (PT) - same | 44-TQFP (PT) - same | 44-TQFP (PT) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Program Memory Type | OTP (14 KB / 8K x 14) | OTP (14 KB) | OTP (14 KB) | Flash (14 KB) | Flash (14 KB) | OTP (14 KB) |
| Maximum CPU Frequency | 10 MHz | 10 MHz | 4 MHz | 10 MHz (20 MHz also offered) | 20 MHz | 20 MHz |
| Operating Temperature | -40 C to +125 C (Extended) | 0 C to +70 C (Commercial) | -40 C to +85 C (Industrial) | -40 C to +85 C (Industrial) | -40 C to +85 C (Industrial) | -40 C to +125 C (Extended) |
| RAM Size | 368 B | 368 B | 368 B | 368 B | 368 B | 368 B |
| ADC | 8-ch, 8-bit | 8-ch, 8-bit | 8-ch, 8-bit | 8-ch, 8-bit | 8-ch, 10-bit | 8-ch, 8-bit |
| Communication Interfaces | AUSART, SPI, I2C (SSP) | AUSART, SPI, I2C | AUSART, SPI, I2C | AUSART, SPI, I2C | AUSART, SPI, I2C | AUSART, SPI, I2C |
| Recommended for New Design | No (NRND) | No (NRND) | No (NRND) | Yes (recommended replacement) | Yes (active) | No (NRND) |
Bảo phân biệt quan trọng
- Recommended modern flash replacement available (vsPIC16F77-I/PT)
- Higher ADC resolution available in same package (vsPIC16F877A-I/PT)
- Faster CPU option in same package (vsPIC16C77-20E/PT)
- Extended temperature grade coverage (vsPIC16C77-10/PT)
Ghi chú thiết kế
Decouple each VDD/VSS pair with a 100 nF ceramic capacitor placed within 10 mm of the IC pins; add a bulk 10 uF electrolytic or tantalum at the board supply entry. The PIC16C77 has separate AVSS/AVDD analog supply pins; route AVSS to the analog ground plane and AVDD through an LC/RC filter to isolate ADC noise from digital switching. The wide 2.5-6.0 V supply range allows operation from a single Li-ion cell or 5 V rail without additional regulation, but never exceed 6.0 V (absolute maximum) - transients above this value destroy the part.
Place the crystal (or ceramic resonator) within 10 mm of OSC1/OSC2 and guard the traces with a grounded ring to reduce EMI pickup. Route MCLR/VPP with a short trace to a 10 kohm pull-up and a 100 nF cap to ground, forming a hardware-reset low-pass filter. For ICSP (in-circuit serial programming), bring PGC/PGD (RB6/RB7) and MCLR/VPP to an in-line 5-pin header accessible without removing the MCU from the board; keep these traces short and free of capacitive loading greater than 50 pF.
OTP memory cannot be erased - verify code with a flash equivalent (PIC16F77, PIC16F877A-I/PT) or a windowed PIC16C77 (with UV-erasable JW package) before programming production units. Brown-out reset must be enabled for field-deployed designs; otherwise a brief VDD sag can cause code corruption or runaway execution. The ADC maximum input must stay within AVSS to AVDD; do not apply negative voltages or voltages above AVDD. The 25 mA I/O drive is per-pin but subject to a package total dissipation limit - check the datasheet thermal characteristics when driving multiple high-current loads simultaneously.
Thông tin tuân thủ
Lifecycle status is NRND (Not Recommended for New Designs). Microchip recommends PIC16F77 as the modern flash replacement. RoHS, REACH, lead-free, and halogen-free status are not explicitly stated in the verified web data and are marked unknown.
