PIC16F1513T-I/SS - 8-bit XLP MCU 7KB Flash 28-SSOP | Microchip
MPN: PIC16F1513T-I/SS ✓ Hoạt độngPIC16F1513T-I/SS Tóm tắt
A PIC microcontroller is a compact, self-contained computer-on-a-chip built around a RISC (Reduced Instruction Set Computer) Harvard architecture. It integrates a CPU core, non-volatile Flash program memory, volatile SRAM, on-chip peripherals (ADC, timers, PWM, communications), and digital I/O pins into a single IC. The PIC16F1513 sits in the mid-range PIC16F1xxx family, positioned above the PIC16F1503/1507/1508/1509 entry-level XLP parts and below the PIC16F171x/176x higher-pin-count variants. Its 28-pin SSOP footprint makes it popular in space-constrained designs that need more I/O than an 8-bit PIC in 14- or 20-pin packages can offer.
Key features include a 20 MHz internal oscillator (with 31 kHz LFINTOSC option for low-power modes), 18 ADC channels with 10-bit resolution, Enhanced Universal Synchronous Asynchronous Receiver Transmitter (EUSART), Master Synchronous Serial Port (MSSP) supporting SPI and I²C, multiple 16-bit timers (TMR1 with gate control, TMR3), 10-bit PWM with up to 4 outputs, and an enhanced Power-On Reset / Brown-Out Reset (POR/BOR). The XLP technology delivers typical sleep currents below 100 nA with Real-Time Clock active, extending battery life in wireless sensor and metering applications.
The architecture uses a 14-bit instruction word and a 14-bit program memory bus, allowing single-word instructions to execute in one instruction cycle (4 clock periods). On-chip in-circuit serial programming (ICSP) and in-circuit debugging (ICD) are supported via standard Microchip development tools (MPLAB X IDE, PICkit™ 5, MPLAB Snap), making the device accessible to engineers across hobby, education, and production settings.
Typical applications include IoT sensor nodes, battery-powered wireless transmitters, home automation controllers, LED lighting drivers, low-end consumer appliances, motor control signal conditioning, industrial sensor interfaces, and remote control receivers. The combination of low-power sleep modes, generous ADC channel count, and standard serial peripherals suits multi-channel analog monitoring where wall power is unavailable.
When designing with the PIC16F1513T-I/SS, plan for decoupling on VDD/VCORE with 100 nF and 10 µF bulk capacitors placed within a few millimetres of the pins. Choose low-power ICSP pin assignments carefully if your PCB exposes the ICSP header - both ICSPCLK and ICSPDAT pins are shared with general-purpose I/O, so adding a low-value series resistor (typically 100 Ω to 470 Ω) can isolate debug circuits from production noise. Operating voltage range spans 1.8 V to 5.5 V.
This page synthesizes distributor pricing, drop-in Microchip same-family alternatives, and practical low-power design notes not collected in any single manufacturer document.
Bộ thay thế dễ dàng lắp đặt cho PIC16F1513T-I/SS — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với PIC16F1513T-I/SS (cùng hình factor và footprint) — khác nhau ở ADC, Package, Timers, Program Memory (Flash), Communication.
PIC16F1513-I/SS
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC16F1509T-I/SS
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC16F1459-I/SS
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC16F1713-I/SS
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
PIC16F1769-I/SS
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →PIC16F1527-I/SS
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
PIC16F1513T-I/SS Tỷ lệ tối đa & tính chất điện
| Device Family | PIC16F1xxx (Mid-Range Core, 14-bit instruction) |
| Core Architecture | 8-bit PIC RISC, Harvard |
| Program Memory (Flash) | 7 KB (4K x 14 words) |
| SRAM | 256 bytes |
| Maximum CPU Speed | 20 MHz |
| Operating Voltage (VDD) | 1.8 V to 5.5 V |
| ADC | 10-bit, up to 17 channels (per family datasheet) |
| Timers | TMR0 (8-bit), TMR1/TMR3 (16-bit with gate), TMR2/TMR4/TMR6 (8-bit) |
| PWM Outputs | 10-bit PWM, up to 4 channels (CCP/ECCP) |
| Communication | EUSART (LIN-capable), MSSP (SPI / I²C) |
| I/O Pins | 27 (28-pin SSOP) |
| Low-Power Feature | XLP nanoWatt technology (sleep current < 100 nA typical) |
| Internal Oscillator | 16 MHz HFINTOSC, 31 kHz LFINTOSC, PLL optional |
| Nhiệt độ hoạt động | -40 °C to +85 °C (Industrial, "I") |
| Hộp | 28-pin SSOP (5.30 mm body) |
| Kiểu lắp đặt | Surface Mount |
| Programming/Debug | ICSP + ICD via MPLAB X IDE / PICkit / MPLAB Snap |
| Trạng thái RoHS | Compliant |
Cấu hình chân PIC16F1513T-I/SS
| Chân 1 | RA3/AN3/VREF+ — Digital I/O / Analog input 3 / ADC positive reference |
| Chân 2 | RA2/AN2 — Digital I/O / Analog input 2 |
| Chân 3 | RA1/AN1/ICSPCLK — Digital I/O / Analog input 1 / ICSP clock |
| Chân 4 | RA0/AN0/ICSPDAT — Digital I/O / Analog input 0 / ICSP data |
| Chân 5 | RA7/OSC1/CLKIN — Digital I/O / Crystal oscillator input / external clock |
| Chân 6 | RA6/OSC2/CLKOUT — Digital I/O / Crystal oscillator output / clock output |
| Chân 7 | VDD — Positive supply voltage (1.8 V to 5.5 V) |
| Chân 8 | VSS — Ground reference |
| Chân 9 | RA5/AN4/SS/HLVDIN — Digital I/O / Analog input 4 / SPI slave select / High/Low-Voltage detect input |
| Chân 10 | RA4/AN3/T0CKI — Digital I/O / Analog input 3 / Timer0 clock input |
| Chân 11 | RC0/SOSCO — Digital I/O / Secondary oscillator output |
| Chân 12 | RC1/SOSCI — Digital I/O / Secondary oscillator input |
| Chân 13 | RC2/AN6 — Digital I/O / Analog input 6 |
| Chân 14 | RC3/AN7 — Digital I/O / Analog input 7 |
| Chân 15 | RC4/AN8 — Digital I/O / Analog input 8 |
| Chân 16 | RC5/AN9 — Digital I/O / Analog input 9 |
| Chân 17 | RC6/AN8/SS — Digital I/O / Analog input 8 / SPI slave select (alt) |
| Chân 18 | RC7/AN9/SDO — Digital I/O / Analog input 9 / SPI data out |
| Chân 19 | VSS — Ground reference |
| Chân 20 | VDD — Positive supply voltage (1.8 V to 5.5 V) |
| Chân 21 | RB0/AN10/INT — Digital I/O / Analog input 10 / External interrupt |
| Chân 22 | RB1/AN11 — Digital I/O / Analog input 11 |
| Chân 23 | RB2/AN12 — Digital I/O / Analog input 12 |
| Chân 24 | RB3/AN13 — Digital I/O / Analog input 13 |
| Chân 25 | RB4/AN14 — Digital I/O / Analog input 14 |
| Chân 26 | RB5/AN15 — Digital I/O / Analog input 15 |
| Chân 27 | RB6/ICSPCLK — Digital I/O / ICSP clock (alternate) |
| Chân 28 | RB7/ICSPDAT — Digital I/O / ICSP data (alternate) |
Ứng dụng tiêu biểu
PIC16F1513T-I/SS phù hợp cho 6 Áp dụngs: Battery-Powered IoT Sensor Node, Home Automation Lighting Controller, Industrial Sensor Signal Conditioning, Low-End Consumer Appliance Control, Remote Control RF Receiver, Educational Microcontroller Platform.
Battery-Powered IoT Sensor Node
The PIC16F1513T-I/SS suits battery-powered IoT sensor nodes because of its XLP nanoWatt architecture and 17 ADC channels. Sleep currents typically below 100 nA allow multi-year operation from a single CR2032 coin cell when the firmware spends most of its time in sleep with periodic wake-ups. The 7 KB Flash fits lightweight LoRaWAN or BLE beacon firmware, while the EUSART and MSSP peripherals drive any external radio module without external glue logic. The 10-bit ADC samples thermistor, photocell, or soil-moisture sensors directly, eliminating dedicated analog ICs.
Được đề xuất
Home Automation Lighting Controller
The PIC16F1513T-I/SS drives multi-channel LED or smart-bulb lighting controllers by combining its 10-bit PWM with up to 4 channels, plus EUSART and MSSP for DMX, I²C, or wireless dimmer interfaces. Its 7 KB Flash supports PWM dimming curves, color-temperature mixing, and simple OTA bootloaders. The 27 I/O pins are sufficient for keypad input, status LEDs, and zero-cross triac drivers. Operating from 1.8 V to 5.5 V lets the same MCU run on battery backup or rectified mains-derived rails.
Được đề xuất
Industrial Sensor Signal Conditioning
The PIC16F1513T-I/SS acts as a 17-channel analog front end in industrial sensor conditioning modules, where its 10-bit ADC digitizes 4-20 mA loop, 0-10 V, or thermocouple signals with adequate resolution for monitoring not control. The PIC RISC core runs simple linearization, threshold alarming, and Modbus RTU framing over EUSART, all within 7 KB Flash. The industrial -40 °C to +85 °C temperature grade and 1.8 V to 5.5 V operation let it sit inside harsh-enclosure sensor hubs without extra regulation.
Được đề xuất
Low-End Consumer Appliance Control
The PIC16F1513T-I/SS handles main control tasks in rice cookers, air purifiers, dehumidifiers, and other low-end consumer appliances. Its 27 I/O pins drive 7-segment or basic LCD displays, accept keypad matrices, and switch triac or MOSFET outputs via PWM. The 20 MHz core and 7 KB Flash fit state-machine firmware plus simple look-up tables for cooking profiles or fan curves. XLP low-power modes keep standby consumption below regulatory limits.
Được đề xuất
Remote Control RF Receiver
The PIC16F1513T-I/SS decodes OOK/FSK remote-control packets in low-power wireless receivers by combining its EUSART for synchronous demodulation, TMR1/TMR3 for carrier timing, and XLP sleep modes between packets. The 7 KB Flash supports rolling-code security algorithms and multiple protocol templates. PICkit-style ICSP on RA0/RA1 enables rapid factory calibration and ID assignment. Operating at 1.8 V to 5.5 V suits coin-cell-powered key fobs and line-powered receivers alike.
Được đề xuất
Educational Microcontroller Platform
Universities and training labs adopt the PIC16F1513T-I/SS as an introductory platform because it pairs the classic PIC16 architecture with enough Flash (7 KB) and ADC channels (17) for meaningful lab projects without the cost of higher-pin-count devices. ICSP and ICD via RA0/RA1 work with the low-cost PICkit 5 or MPLAB Snap debugger. The 28-SSOP package is breadboard-friendly with SSOP-to-DIP adapters, and the XLP nanoWatt features provide hands-on lessons in low-power firmware design.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho PIC16F1513T-I/SS — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | PIC16F1513-I/SS | PIC16F1509T-I/SS | PIC16F1459-I/SS | PIC16F1713-I/SS | PIC16F1769-I/SS | PIC16F1527-I/SS |
|---|---|---|---|---|---|---|---|
| Package | 28-SSOP | 28-SSOP - same | 28-SSOP - same | 28-SSOP - same | 28-SSOP - same | 28-SSOP - same | 28-SSOP - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Flash Memory | 7 KB | 7 KB | 5 KB | 14 KB | 16 KB | 14 KB | 28 KB |
| SRAM | 256 B | 256 B | 256 B | 8 KB | 1 KB | 1 KB | 1.5 KB |
| Max CPU Speed | 20 MHz | 20 MHz | 20 MHz | 48 MHz (USB PLL) | 32 MHz | 32 MHz | 20 MHz |
| ADC Channels | 17 | 17 | 12 | 9 | 17 | 17 | 17 |
| Operating Voltage | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 2.3 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V |
| Operating Temperature | -40 °C to +85 °C | -40 °C to +85 °C | -40 °C to +85 °C | -40 °C to +85 °C | -40 °C to +85 °C | -40 °C to +85 °C | -40 °C to +85 °C |
| Special Features | XLP, 10-bit ADC, EUSART, MSSP | XLP, 10-bit ADC, EUSART, MSSP | XLP, 10-bit ADC, EUSART, MSSP | XLP, USB Full-Speed, MSSP, EUSART | XLP, 10-bit ADC, 5-bit DAC, op-amp, angular timer | XLP, 10-bit ADC, 10-bit DAC, op-amp | XLP, 10-bit ADC, MSSP, EUSART, 2x CCP |
| Unit Price (1 pc) | $1.62 | $1.55 (Tube) | $1.45 | $1.85 | $2.10 | $2.05 | $2.35 |
Bảo phân biệt quan trọng
- 17 ADC channels with XLP nanoWatt sleep on 28-SSOP (vsPIC16F1509T-I/SS)
- Same XLP architecture at lower cost vs 14 KB Flash parts (vsPIC16F1459-I/SS)
- Right-sized memory avoids overpaying for 16 KB Flash (vsPIC16F1713-I/SS)
- Industrial -40 °C to +85 °C temperature grade standard (vsPIC16F1503-I/ST (TSSOP package))
Ghi chú thiết kế
Estimated: at 20 MHz active and 3.3 V VDD, the PIC16F1513T-I/SS typically draws around 2 mA active current. In Sleep with Watchdog disabled, this drops to under 100 nA, per the XLP datasheet. Always place a 100 nF decoupling capacitor within 5 mm of each VDD pin (pins 7 and 20) and a bulk 10 µF on the supply rail. For battery-powered designs, configure the LFINTOSC to 31 kHz before entering Sleep and use Timer1 with external 32.768 kHz crystal for RTC operation.
Route the ICSP lines (RA0/ICSPDAT and RA1/ICSPCLK) directly to a 2x3 or 1x6 programming header with no series resistors in normal production. For in-circuit debugging in noisy environments, add 100 Ω to 470 Ω series resistors on these lines, and ensure no high-current traces run parallel to ICSP for more than 25 mm to avoid coupling. Keep the SSOP-28 thermal pad on the package connected to VSS or left floating - the SSOP-28 has no exposed thermal pad unlike QFN variants.
Do not leave the MCLR pin floating - tie it to VDD through a 10 kΩ pull-up for normal operation, or to a debugger reset line during development. The PIC16F1513T-I/SS does not have internal MCLR pull-up on all revisions; check the CONFIG register settings in your code. Also avoid using RA0/RA1 as analog inputs and ICSP simultaneously - configure the APFCON register so the ICSP function does not interfere with sensor sampling.
When using the ADC at 10-bit resolution, add a 10 nF bypass capacitor at the VREF+ pin (RA3) if a separate voltage reference is used. Source impedance above 10 kΩ on ADC inputs causes acquisition-time errors and reduces effective resolution. For multi-channel scanning above 50 ksps, switch to the internal 2.048 V or 4.096 V FVR reference to minimize reference drift across the operating temperature range.
Thông tin tuân thủ
RoHS and REACH compliance per Microchip product environmental compliance page. AEC-Q100 not applicable - this part is not qualified to automotive grade. For automotive designs, use the PIC16F1513-E/SS extended-temperature variant or PIC16F1713T-I/SS.
