PIC16F716-E/SS - 20MHz 8-Bit Flash MCU | Microchip Technology
MPN: PIC16F716-E/SS ✓ Hoạt độngPIC16F716-E/SS Tóm tắt
An 8-bit Flash microcontroller is a programmable semiconductor that combines a CPU, program memory, data memory and peripherals on one integrated circuit. Within the embedded-control hierarchy, the PIC16F716 belongs to the PIC16 family of 8-bit RISC microcontrollers. It combines a conventional processor core with mixed-signal peripherals, allowing a design to measure analog inputs, control outputs, and execute embedded control logic without requiring separate components for every function.
Key features include a 20 MHz maximum clock speed, 3.5 KB of Flash program memory organized as 2K by 14 bits, and 128 bytes of RAM. The four-channel 8-bit A/D converter supports applications that need sensor measurements, while enhanced capture, compare and PWM modules provide flexible timing and waveform-generation functions. Operation across 2.5 V, 3.3 V and 5 V supply options allows the same controller family to address low-voltage control, sensor-interface and conventional embedded applications.
The PIC16F716 architecture uses a compact RISC-based instruction set and integrates the A/D converter, timers, I/O ports, and enhanced capture/compare/PWM peripherals into a single device. Its 128 bytes of RAM limit the amount of simultaneous volatile data that can be retained, so register allocation and buffering strategy should be planned carefully. Flash program memory supports field-programmable embedded logic, while the A/D subsystem provides a direct interface to resistive, resistive-divider and other analog sensors.
Typical applications include industrial motor and appliance controls, automotive interface modules, consumer products, and compact sensor nodes. The combination of four analog channels and multiple timers is useful in fan controllers, temperature monitors, keypad interfaces, and small closed-loop control systems. The 20-pin SSOP also permits a relatively compact PCB footprint when fine-pitch assembly and adequate board spacing are available.
Designers should reserve all supply pins for proper decoupling, route analog inputs away from switching nodes, and maintain the voltage and current limits stated in the manufacturer datasheet. The -E suffix identifies the specified temperature grade, while /SS identifies the 20-pin SSOP package and SS provides the extended operating-temperature designation associated with this ordering code.
This product page consolidates the manufacturer specifications, package details, programming resources, commercially relevant sourcing information, and clearly identified drop-in alternatives. It also highlights the constraints that matter most when deciding whether the PIC16F716-E/SS fits a new embedded-control design or whether a different MCU should be selected.
Bộ thay thế dễ dàng lắp đặt cho PIC16F716-E/SS — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với PIC16F716-E/SS (cùng hình factor và footprint) — khác nhau ở Package, Timers, ADC, Program Memory (Flash), RoHS Status.
PIC16F716-I/SS
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC16F716-E/SS Tỷ lệ tối đa & tính chất điện
| Product Type | 8-bit Flash-based RISC microcontroller |
| Maximum Clock Speed | 20 MHz |
| Program Memory | 3.5 KB Flash (2K x 14 bits) |
| Data Memory | 128 bytes RAM |
| A/D Converter Resolution | 8 bits |
| A/D Converter Channels | 4 channels |
| Additional Timers | 2 timers |
| I/O Pin Count | 13 I/O pins |
| Điện áp cung cấp hoạt động | 2.5 V to 5.5 V |
| Supported Supply Levels | 2.5 V, 3.3 V and 5 V |
| Enhanced Peripherals | Enhanced capture, compare and PWM |
| Hộp | 20-pin SSOP |
| Kiểu lắp đặt | Surface mount |
| Terminal Count | 20 terminals |
| Trạng thái vòng đời | Active |
| Temperature Grade | -E extended temperature grade |
Hướng dẫn cấu hình chân PIC16F716-E/SS 20-pin ssop
Cấu hình chân cho PIC16F716-E/SS (20-pin ssop gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho PIC16F716-E/SS.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
PIC16F716-E/SS phù hợp cho 6 Áp dụngs: Industrial Sensor Monitoring, Fan and Motor Control, Appliance Control Module, Automotive Interface Control, Consumer Product Interface, Embedded Timer and Counter.
Industrial Sensor Monitoring
The PIC16F716-E/SS fits industrial sensor-monitoring designs that require four analog measurement channels without a separate ADC. Its 8-bit A/D converter can read resistive or divider-based sensors, while 128 bytes of RAM provides working storage for current readings and control state. The 20 MHz clock supports responsive sampling and filtering, and two additional timers can organize acquisition intervals or periodic control actions. Keep analog traces short, isolate them from switching nodes, and reference the electrical-characteristics limits before selecting external sensor ranges.
Được đề xuất
Fan and Motor Control
The PIC16F716-E/SS is appropriate for compact fan or small-motor controllers that combine speed measurement with controlled drive timing. Its four A/D channels can monitor a supply, temperature, or motor-related analog signal, while the additional timers and enhanced PWM functions organize switching or modulation functions. The 13 available I/O pins leave room for control outputs and status signals. Designers should calculate timing and drive current from the selected external transistors and motors because those load ratings are not defined by the microcontroller itself.
Được đề xuất
Appliance Control Module
The PIC16F716-E/SS supports appliance-control boards that must read analog inputs and coordinate several timed outputs. Its four-channel 8-bit A/D converter can monitor temperature, position, or level signals, while enhanced capture, compare and PWM functions can simplify operating cycles and actuator timing. The 3.5 KB Flash capacity is suitable for focused control firmware, although 128 bytes of RAM requires disciplined buffer management. Firmware should include safe output states for power loss, sensor faults, and actuator overload conditions.
Được đề xuất
Automotive Interface Control
The PIC16F716-E/SS can support compact automotive interface and auxiliary-control functions where four analog inputs and multiple timed I/O resources are useful. Microchip identifies automotive applications among the PIC16F716 family's intended markets, and the device combines 20 MHz processing with 13 I/O pins. A production automotive design must still verify the exact temperature grade, transient limits, EMC requirements and vehicle load-dump protection externally. The MCU should not be connected directly to vehicle power or long harness wiring without appropriate protection.
Được đề xuất
Consumer Product Interface
The PIC16F716-E/SS is suitable for compact consumer products requiring local sensing, user input and timed output control. Its four analog inputs can support touch, level or temperature-related functions, while the timers and PWM peripherals can drive indicators or simple actuators. The 20-pin SSOP reduces board area compared with larger packages, making the device useful in space-constrained products. Firmware organization must account for the 128-byte RAM limit, and production programming should follow the device programming specification for reliable field or manufacturing integration.
Được đề xuất
Embedded Timer and Counter
The PIC16F716-E/SS can serve as the central controller in a compact timer, event counter or repetitive-sequence product. Two additional timers complement the core timing resources, while the 13 I/O pins support input capture, output events and status indication. A 20 MHz clock provides a higher processing ceiling for debouncing, event handling and display updates, and the four A/D channels can supervise an analog process variable. Define timer prescaler and interrupt latency requirements during firmware planning so scheduling remains deterministic.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho PIC16F716-E/SS — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | PIC16F716-I/SS |
|---|---|---|
| Brand | Microchip Technology | Microchip Technology |
| Package | 20-pin SSOP | 20-pin SSOP - same |
| Architecture | 8-bit PIC16 RISC | 8-bit PIC16 RISC |
| Maximum Clock Speed | 20 MHz | 20 MHz |
| Program Memory | 3.5 KB Flash (2K x 14 bits) | 3.5 KB Flash |
| RAM | 128 bytes | 128 bytes |
| A/D Converter | 4 channels at 8 bits | 4 channels at 8 bits |
| I/O Pins | 13 I/O pins | 13 I/O pins |
| Supply Voltage Range | 2.5 V to 5.5 V | 2.5 V to 5.5 V |
| Temperature Grade | -E extended temperature grade | -I industrial temperature grade |
| Enhanced PWM | Available | Available |
Bảo phân biệt quan trọng
- Same-footprint alternative within the exact PIC16F716 family (vsPIC16F716-I/SS)
- Four-channel analog measurement in a compact controller (vsPIC16F716-I/SS)
- Flexible 2.5 V to 5.5 V operating range (vsPIC16F716-I/SS)
Ghi chú thiết kế
Place the supply bypass capacitor close to the device power pins and connect the ground return directly to the ground plane. Follow the capacitor value and placement recommendations in the Microchip Technology PIC16F716 datasheet DS41206B. Keep analog and digital return currents separated where possible, and verify the design against the operating range of 2.5 V to 5.5 V.
Use the 20-pin SSOP land pattern from the manufacturer package drawing and verify all pad dimensions against the final PCB library. Maintain adequate spacing between adjacent copper features because the 0.50 mm package pitch limits assembly clearance. Inspect solder joints after reflow, particularly on the oscillator, programming and analog-input pins where access or thermal cycling can affect reliability.
Route the four analog inputs away from switching nodes, relay contacts, clock lines and high-current return paths. Use a quiet ground reference for A/D input filtering, and place any input network close to the controller to minimize pickup. The four-channel 8-bit converter is intended for compact control signals, so input conditioning must keep source impedance and settling behavior compatible with the acquisition sequence.
Do not treat the -E suffix as a universal substitute for every PIC16F716 ordering code, and do not interchange the /SS package with /SO or other package options without checking the PCB footprint. Confirm the programming interface, oscillator configuration, I/O assignments and temperature limits in DS41206B. The 128-byte RAM limit also makes stack and buffer-depth checks important for firmware stability.
Thông tin tuân thủ
The exact compliance declarations for PIC16F716-E/SS must be confirmed through the manufacturer's product documentation or a current compliance statement.