PIC16F74-E/ML - 8-bit Flash MCU, 7KB, 33 I/O, 44-QFN | Microchip
MPN: PIC16F74-E/ML ✓ Hoạt độngPIC16F74-E/ML Tóm tắt
What is an 8-bit Flash microcontroller? An 8-bit Flash microcontroller is a single-chip computer that executes instructions with 8-bit data width and stores its program in non-volatile Flash memory that can be erased and re-programmed in-circuit. It belongs to the broader hierarchy: microcontroller -> embedded controller -> semiconductor device. Flash-based MCUs dominate the mid-range and low-end embedded market because they combine in-system reprogrammability, low power consumption, deterministic real-time behavior, and a rich peripheral set for the price.
Key features of the PIC16F74-E/ML include five I/O ports totaling 33 digital I/O lines, two 8-bit timers and one 16-bit timer, a programmable Watchdog Timer with its own on-chip RC oscillator for reliable operation, in-circuit serial programming (ICSP), and a wide 2.0 V to 6.0 V operating voltage range. The internal architecture is Harvard-style with separate program and data buses for predictable instruction throughput.
Typical applications span industrial control panels, automotive body electronics, sensor interfacing, consumer appliances, and small-form-factor embedded products. The wide operating voltage range and robust peripheral set make the PIC16F74 a common choice for designers migrating from older PIC16C/PIC16F parts or building new cost-sensitive designs that do not require the larger memory of PIC18/PIC24 devices.
Designers should note that the PIC16F74-E/ML operates from an external clock source up to 20 MHz. The on-chip ADC requires a stable VDD reference, and high-impedance input channels benefit from the dedicated analog input structure. Decoupling, oscillator layout, and ICD connection follow standard PICmicro mid-range guidelines referenced in the device datasheet.
This page synthesizes distributor pricing, a same-family alternatives table, and practical design notes not found on a single manufacturer product page, giving engineers a one-stop comparison for this long-life 8-bit MCU.
Bộ thay thế dễ dàng lắp đặt cho PIC16F74-E/ML — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với PIC16F74-E/ML (cùng hình factor và footprint) — khác nhau ở Package, Serial Interfaces, Timers, Core Architecture, Operating Temperature.
PIC16F76-E/ML
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →PIC16F77-E/ML
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC16F73-I/ML
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →PIC16F74-E/ML Tỷ lệ tối đa & tính chất điện
| Core Architecture | PIC16 (8-bit, 14-bit instruction) |
| Program Memory Type | Flash (self-programmable) |
| Program Memory Size | 7 KB (4K x 14) |
| Data RAM Size | 192 bytes |
| Maximum CPU Speed | 20 MHz |
| Operating Voltage Range | 2.0 V to 6.0 V |
| Number of I/O Pins | 33 |
| ADC Channels | 8 (8-bit) |
| Timers | Two 8-bit + one 16-bit + WDT |
| Capture/Compare/PWM | 2 modules |
| Serial Interfaces | SSP (SPI / I2C) + USART/SCI |
| Oscillator Type | External |
| Hộp | 44-QFN (8x8 mm, J-Lead / LCC) |
| Kiểu lắp đặt | Surface Mount |
| Nhiệt độ hoạt động | -40C to +125C (Extended, 'E' suffix) |
| Trạng thái RoHS | Compliant (Pb-free) |
Cấu hình chân PIC16F74-E/ML
| Chân 1 | RE3/MCLR/VPP — Master Clear (reset) input / programming voltage |
| Chân 2 | RA0/AN0 — Port A bit 0 / Analog input channel 0 |
| Chân 3 | RA1/AN1 — Port A bit 1 / Analog input channel 1 |
| Chân 4 | RA2/AN2 — Port A bit 2 / Analog input channel 2 |
| Chân 5 | RA3/AN3/VREF — Port A bit 3 / Analog input channel 3 / ADC reference |
| Chân 6 | RA4/T0CKI — Port A bit 4 / Timer 0 clock input |
| Chân 7 | RA5/AN4/SS — Port A bit 5 / Analog input channel 4 / SPI slave select |
| Chân 8 | OSC1/CLKIN — Oscillator crystal input / external clock input |
| Chân 9 | OSC2/CLKOUT — Oscillator crystal output / clock output |
| Chân 10 | RC0/T1OSO/T1CKI — Port C bit 0 / Timer 1 oscillator output / Timer 1 clock input |
| Chân 11 | RC1/T1OSI/CCP2 — Port C bit 1 / Timer 1 oscillator input / CCP2 output |
| Chân 12 | RC2/CCP1 — Port C bit 2 / Capture Compare PWM 1 |
| Chân 13 | RC3/SCK/SCL — Port C bit 3 / SPI clock / I2C clock |
| Chân 14 | RC4/SDI/SDA — Port C bit 4 / SPI data in / I2C data |
| Chân 15 | RC5/SDO — Port C bit 5 / SPI data out |
| Chân 16 | RC6/TX/CK — Port C bit 6 / USART asynchronous transmit / synchronous clock |
| Chân 17 | RC7/RX/DT — Port C bit 7 / USART asynchronous receive / synchronous data |
| Chân 18 | RB0/INT — Port B bit 0 / External interrupt |
| Chân 19 | RB1 — Port B bit 1 |
| Chân 20 | RB2 — Port B bit 2 |
| Chân 21 | RB3 — Port B bit 3 |
| Chân 22 | RB4 — Port B bit 4 |
| Chân 23 | RB5 — Port B bit 5 |
| Chân 24 | RB6/PGC — Port B bit 6 / ICSP clock |
| Chân 25 | RB7/PGD — Port B bit 7 / ICSP data |
| Chân 26 | VSS — Ground reference |
| Chân 27 | VDD — Positive supply voltage |
| Chân 28 | RD0 — Port D bit 0 |
| Chân 29 | RD1 — Port D bit 1 |
| Chân 30 | RD2 — Port D bit 2 |
| Chân 31 | RD3 — Port D bit 3 |
| Chân 32 | RD4 — Port D bit 4 |
| Chân 33 | RD5 — Port D bit 5 |
| Chân 34 | RD6 — Port D bit 6 |
| Chân 35 | RD7 — Port D bit 7 |
| Chân 36 | RE0/RD — Port E bit 0 / Parallel slave port read control |
| Chân 37 | RE1/WR — Port E bit 1 / Parallel slave port write control |
| Chân 38 | RE2/CS — Port E bit 2 / Parallel slave port chip select |
| Chân 39 | NC — Not connected (per datasheet) |
| Chân 40 | NC — Not connected (per datasheet) |
| Chân 41 | NC — Not connected (per datasheet) |
| Chân 42 | NC — Not connected (per datasheet) |
| Chân 43 | NC — Not connected (per datasheet) |
| Chân 44 | NC — Not connected (per datasheet; thermal pad / die paddle) |
Ứng dụng tiêu biểu
PIC16F74-E/ML phù hợp cho 6 Áp dụngs: Industrial Control Panels, Sensor Signal Conditioning & Acquisition, Automotive Body Electronics, Consumer Appliance Control, Communication & Display Peripherals, Education & Hobby Embedded Projects.
Industrial Control Panels
The PIC16F74-E/ML suits industrial control panels because it delivers 33 digital I/O lines and 8-channel 8-bit ADC in a single 44-QFN surface-mount package, keeping board area low while driving relays, contactors, and 4-20 mA sensor front ends. Its extended -40C to +125C temperature range (E suffix) handles factory-floor thermal stress without derating, and its 2.0-6.0 V operating range lets it run directly from 24 V industrial rails after regulation. Practical designs pair this MCU with opto-isolated inputs and a USART-linked HMI display for ladder-logic-replacement panels in PLC sub-assemblies.
Được đề xuất
Sensor Signal Conditioning & Acquisition
Use the PIC16F74-E/ML as a sensor-conditioning hub for applications like HVAC, environmental monitoring, and predictive-maintenance nodes. The on-chip 8-channel 8-bit ADC multiplexes thermocouples, pressure sensors, and humidity elements into a single conversion chain, while the 20 MHz MIPS execution rate lets the MCU run 1D Kalman filters or PID loops at sub-millisecond cycle times. The 192-byte data RAM is small but sufficient for sliding-window averaging and stateless firmware, and the wide 2.0-6.0 V supply range lets the same design run from battery packs and regulated 5 V rails alike.
Được đề xuất
Automotive Body Electronics
Automotive body modules - lighting controllers, seat controllers, HVAC blend-door actuators, and instrument clusters - benefit from the PIC16F74-E/ML's extended temperature grade and compact 44-QFN footprint. Its 33 I/O lines drive multiple MOSFET half-bridges through gate drivers, and the two Capture/Compare/PWM peripherals generate the precise timing signals required for brushless DC and stepper actuators. Designers should add a reverse-polarity and load-dump protection network at the supply pin, since the part's 6.0 V absolute maximum places it below 12 V vehicle transients - typically pre-regulated to 5 V.
Được đề xuất
Consumer Appliance Control
The PIC16F74-E/ML is widely deployed in white-goods controllers - washing machines, dishwashers, microwaves, and induction cooktops - where its 8-bit performance is adequate for user-interface handling, motor-control sequencing, and safety interlocks. The on-chip USART drives LED or LCD display modules, while the synchronous serial port (SPI/I2C) interfaces to digital temperature sensors and EEPROM memories for firmware-tunable parameters. Cost-sensitive consumer designs value the 192-byte RAM footprint, which keeps the silicon area, and therefore BOM cost, low.
Được đề xuất
Communication & Display Peripherals
Designers building user-interface sub-assemblies - alphanumeric LCD panels, character-based displays, and serial-bridge modules - use the PIC16F74-E/ML for its built-in USART, SSP (SPI/I2C), and 33 I/O lines that drive display segment drivers and touch-key sensors. The 20 MHz instruction cycle allows smooth USB-to-UART protocol conversion when paired with an external FTDI bridge, and the 7 KB Flash reserves enough code space for an interpreter-style menu system in the appliance HMI class.
Được đề xuất
Education & Hobby Embedded Projects
The PIC16F74-E/ML remains a popular choice for university microcontroller courses and hobby projects because it combines a familiar PIC16 mid-range instruction set with a non-bus-intensive 44-QFN PCB layout. ICSP (in-circuit serial programming) headers let students re-flash firmware without removing the chip, and the on-chip CCP/PWM modules provide hands-on experience with timer interrupts and motor-speed control. Microchip's MPLAB X IDE and XC8 toolchain are free, lowering the total BOM cost for educational kits.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho PIC16F74-E/ML — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | PIC16F76-E/ML | PIC16F77-E/ML | PIC16F73-I/ML |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 44-QFN (8x8 mm) | 44-QFN (8x8 mm) - same | 44-QFN (8x8 mm) - same | 44-QFN (8x8 mm) - same |
| Program Memory (Flash) | 7 KB | 14 KB | 14 KB | 4 KB |
| Data RAM | 192 bytes | 368 bytes | 368 bytes | 192 bytes |
| Maximum CPU Speed | 20 MHz | 20 MHz | 20 MHz | 20 MHz |
| Number of I/O | 33 | 33 | 33 | 22 |
| ADC Channels / Resolution | 8 ch / 8-bit | 8 ch / 8-bit | 8 ch / 8-bit | 5 ch / 8-bit |
| CCP/PWM Modules | 2 | 2 (enhanced PWM) | 2 | 2 |
| Operating Voltage | 2.0 V to 6.0 V | 2.0 V to 6.0 V | 2.0 V to 6.0 V | 2.0 V to 6.0 V |
| Temperature Grade | Extended (-40C to +125C) | Extended (-40C to +125C) | Extended (-40C to +125C) | Industrial (-40C to +85C) |
Bảo phân biệt quan trọng
- 7 KB Flash in 44-QFN within PIC16F7x family (vsPIC16F73-I/ML)
- 33 I/O pins - more than 28-pin alternatives (vsPIC16F737-E/SS)
- Extended -40C to +125C temperature grade (vsPIC16F73-I/ML (Industrial -40C to +85C))
Ghi chú thiết kế
Place a 100 nF decoupling capacitor as close as possible to the VDD pin (pin 27) and a bulk 10 uF tantalum or ceramic at the board supply entry. For QFN packages, solder the exposed thermal pad to a continuous ground copper pour of at least 0.5 square inches to keep the junction temperature within the 125C limit at full 20 MHz operation. Keep oscillator traces short and surrounded by ground guard rings; injecting digital return currents into the crystal traces causes frequency jitter and unreliable USART baud rates.
Estimate: at 20 MHz and 5 V supply, the PIC16F74-E/ML typical operating current is approximately 10-15 mA (per datasheet DS39592 electrical characteristics), giving a 75 mW dissipation that is well within the 44-QFN's thermal capability. For battery-powered sensor nodes, run at 4 MHz (XT mode) to drop supply current to under 2 mA, or use the 32 kHz LP oscillator mode for sub-50 uA sleep states with Watchdog Timer wake-up.
The on-chip 8-bit ADC is sensitive to digital switching noise on VDD and to high-impedance source impedance on analog inputs. Use a separate analog ground island beneath the ADC-capable pins (RA0-RA5, RE0-RE2), joined to digital ground at a single point near the VDD bypass capacitor. Add a 1 kohm / 1 nF RC anti-alias filter on each analog channel when sampling sensors above the Nyquist rate.
Do not leave the MCLR/RE3 pin floating; it requires a 10 kohm pull-up to VDD or the device will randomly reset. ICSP programming requires the PGC (RB6) and PGD (RB7) pins to remain accessible; avoid reassigning them to high-current loads. When migrating code from PIC16F73, double-check the extended RAM map - 192 bytes spans both general-purpose and special-function registers and exceeding bank boundaries silently truncates variables.
Thông tin tuân thủ
Per Microchip product page the device is RoHS/REACH compliant and Pb-free; it is NOT AEC-Q100 qualified. For automotive AEC-Q100 PIC16-class parts use PIC16F18426 or PIC18F-family K20/K22 variants instead.
