PIC16F877A-E/L - 8-bit 20MHz 14KB Flash MCU 44-PLCC | Microchip
MPN: PIC16F877A-E/L ✓ Hoạt độngPIC16F877A-E/L Tóm tắt
An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, RAM, non-volatile program memory, peripherals, and I/O on one die. PIC16F-series MCUs belong to the enhanced mid-range family of Microchip's PIC microcontroller hierarchy: PIC10/12/14/16 (base-line and mid-range 8-bit) -> PIC16 (mid-range, enhanced mid-range) -> PICmicro 8-bit -> Microcontroller -> Semiconductor. They are designed for deterministic, low-power embedded control with a small instruction footprint (35 instructions on the PIC16F877A).
Key features of the PIC16F877A include a 10-bit Analog-to-Digital Converter (ADC) with up to 8 input channels, two 8-bit timers plus one 16-bit timer, two Capture/Compare/PWM (CCP) modules, an Enhanced Universal Synchronous Asynchronous Receiver Transmitter (EUSART), a Master Synchronous Serial Port (MSSP) configurable for SPI or I2C, an ICD (In-Circuit Debug) interface, two analog comparators, brown-out reset (BOR), and a programmable watchdog timer. The Harvard architecture and 14-bit instruction word allow compact, predictable code execution.
Typical applications include industrial control systems, HVAC controllers, automotive body and interior electronics, sensor signal conditioning, low-cost instrumentation, and education/development platforms where the PIC16F877A is a long-standing reference design. The wide operating voltage and rich analog/digital peripheral mix make it suitable for replacing multiple discrete components with one programmable solution.
When designing with this device, ensure proper decoupling (100 nF + 10 uF bulk) near VDD pins, place the MCLR pull-up correctly for in-circuit debugging, and verify I/O assignments against the 44-pin PLCC pinout. The internal RC oscillator can be used to save cost, but a crystal is recommended for timing-sensitive UART or PWM applications.
Bộ thay thế dễ dàng lắp đặt cho PIC16F877A-E/L — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với PIC16F877A-E/L (cùng hình factor và footprint) — khác nhau ở Package, Operating Temperature, Core Architecture, Serial Interfaces, Timers.
PIC16F877-20/L
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →PIC16F877-20I/L
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →PIC16F871-E/L
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC18F458-E/L
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC16F877A-I/L
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →PIC16F877A-E/L Tỷ lệ tối đa & tính chất điện
| Core | PIC16 |
| Architecture | 8-bit Harvard RISC |
| Instruction Set | 35 single-word instructions |
| Instruction Cycle Time | 200 ns @ 20 MHz |
| Tần số xung maksimum | 20 MHz |
| Program Memory (Flash) | 14 KB (8K x 14 words) |
| Data Memory (SRAM) | 368 bytes |
| Data EEPROM | 256 bytes |
| Supply Voltage (VDD) | 2.0 V to 5.5 V |
| Nhiệt độ hoạt động | -40 C to +125 C (Extended grade, "E") |
| I/O Pins | 33 |
| ADC | 10-bit, up to 8 channels |
| Timers | 2 x 8-bit, 1 x 16-bit |
| CCP Modules | 2 (Capture/Compare/PWM) |
| Serial Interfaces | MSSP (SPI / I2C), EUSART (RS-232/RS-485) |
| Comparators | 2 analog |
| In-Circuit Debug | Yes (ICD) |
| Brown-out Reset | Yes |
| Watchdog Timer | Yes (programmable) |
| Hộp | 44-pin PLCC (J-lead, 16.59 x 16.59 mm) |
| Kiểu lắp đặt | Surface Mount |
| Cấp MSL | 3 (168 hours) |
| Trạng thái RoHS | Compliant |
Cấu hình chân PIC16F877A-E/L
| Chân 1 | MCLR/VPP — Master Clear (Reset) input / Programming voltage |
| Chân 2 | RA0/AN0 — PORTA bit 0 / Analog input 0 |
| Chân 3 | RA1/AN1 — PORTA bit 1 / Analog input 1 |
| Chân 4 | RA2/AN2/VREF- — PORTA bit 2 / Analog input 2 / ADC VREF- |
| Chân 5 | RA3/AN3/VREF+ — PORTA bit 3 / Analog input 3 / ADC VREF+ |
| Chân 6 | RA4/T0CKI — PORTA bit 4 / Timer0 clock input |
| Chân 7 | RA5/AN4/SS — PORTA bit 5 / Analog input 4 / SPI slave select |
| Chân 8 | RE0/RD/AN5 — PORTE bit 0 / Parallel port read control / Analog input 5 |
| Chân 9 | RE1/WR/AN6 — PORTE bit 1 / Parallel port write control / Analog input 6 |
| Chân 10 | RE2/CS/AN7 — PORTE bit 2 / Parallel port chip select / Analog input 7 |
| Chân 11 | VDD — Positive supply voltage (+5 V typical) |
| Chân 12 | VSS — Ground reference |
| Chân 13 | OSC1/CLKIN — Oscillator input / External clock input |
| Chân 14 | OSC2/CLKOUT — Oscillator output / Clock output |
| Chân 15 | RC0/T1OSO/T1CKI — PORTC bit 0 / Timer1 oscillator output / Timer1 clock input |
| Chân 16 | RC1/T1OSI/CCP2 — PORTC bit 1 / Timer1 oscillator input / CCP2 I/O |
| Chân 17 | RC2/CCP1 — PORTC bit 2 / CCP1 I/O (Capture/Compare/PWM) |
| Chân 18 | RC3/SCK/SCL — PORTC bit 3 / SPI clock / I2C clock |
| Chân 19 | RC4/SDI/SDA — PORTC bit 4 / SPI data in / I2C data |
| Chân 20 | RC5/SDO — PORTC bit 5 / SPI data out |
| Chân 21 | RC6/TX/CK — PORTC bit 6 / EUSART async transmit / sync clock |
| Chân 22 | RC7/RX/DT — PORTC bit 7 / EUSART async receive / sync data |
| Chân 23 | RD0/PSP0 — PORTD bit 0 / Parallel slave port bit 0 |
| Chân 24 | RD1/PSP1 — PORTD bit 1 / Parallel slave port bit 1 |
| Chân 25 | RD2/PSP2 — PORTD bit 2 / Parallel slave port bit 2 |
| Chân 26 | RD3/PSP3 — PORTD bit 3 / Parallel slave port bit 3 |
| Chân 27 | RD4/PSP4 — PORTD bit 4 / Parallel slave port bit 4 |
| Chân 28 | RD5/PSP5 — PORTD bit 5 / Parallel slave port bit 5 |
| Chân 29 | RD6/PSP6 — PORTD bit 6 / Parallel slave port bit 6 |
| Chân 30 | RD7/PSP7 — PORTD bit 7 / Parallel slave port bit 7 |
| Chân 31 | VSS — Ground reference |
| Chân 32 | VDD — Positive supply voltage (+5 V typical) |
| Chân 33 | RB0/INT — PORTB bit 0 / External interrupt input |
| Chân 34 | RB1 — PORTB bit 1 |
| Chân 35 | RB2 — PORTB bit 2 |
| Chân 36 | RB3/PGM — PORTB bit 3 / Low-voltage programming input |
| Chân 37 | RB4 — PORTB bit 4 |
| Chân 38 | RB5 — PORTB bit 5 |
| Chân 39 | RB6/PGC — PORTB bit 6 / In-circuit debugger clock |
| Chân 40 | RB7/PGD — PORTB bit 7 / In-circuit debugger data |
| Chân 41 | NC — Not connected (per datasheet) |
| Chân 42 | NC — Not connected (per datasheet) |
| Chân 43 | NC — Not connected (per datasheet) |
| Chân 44 | NC — Not connected (per datasheet) |
Ứng dụng tiêu biểu
PIC16F877A-E/L phù hợp cho 6 Áp dụngs: Industrial Control Systems, HVAC and Building Automation, Educational and Development Platforms, Sensor Signal Conditioning Nodes, Automotive Body Electronics, Low-Cost Instrumentation.
Industrial Control Systems
The PIC16F877A-E/L is a strong fit for industrial control with 33 digital I/O to drive relays, contactors, and discrete sensors, plus a 10-bit ADC for analog process variables. Its 2.0 V to 5.5 V supply range tolerates 24 V industrial bus rails after simple regulation. Hardware PWM and CCP modules simplify closed-loop PID loops for motor or valve control without software overhead.
Được đề xuất
HVAC and Building Automation
The PIC16F877A-E/L handles multi-zone HVAC control by reading temperature sensors via its 10-bit ADC and driving triac/SSR outputs through its CCP/PWM modules. The MSSP interface supports I2C temperature/humidity sensor arrays, while EUSART links to building management networks. The Extended temperature grade (-40 C to +125 C) supports unconditioned rooftop and basement installations.
Được đề xuất
Educational and Development Platforms
The PIC16F877A-E/L is the canonical reference microcontroller for embedded systems curricula, with decades of academic tutorials, datasheets, and example code. Its 44-pin PLCC is easy to socket on development boards, while the in-circuit debugger (ICD) interface enables live debugging in MPLAB X. The 14 KB Flash accommodates multiple student projects without reprogramming hardware.
Được đề xuất
Sensor Signal Conditioning Nodes
The PIC16F877A-E/L integrates sensor signal paths by multiplexing multiple analog sensors through the 10-bit ADC, processing thresholds, and driving outputs via SPI or UART. Its 5 MIPS performance is adequate for digital filtering (moving average, basic Kalman) on slow-changing sensor signals. The wide 2.0 V to 5.5 V supply supports battery and 5 V bus operation.
Được đề xuất
Automotive Body Electronics
The PIC16F877A-E/L is used in non-safety automotive body modules such as interior lighting controllers, seat adjusters, and HVAC panels. Its Extended temperature grade (-40 C to +125 C) handles under-dash environments, while the 33 I/O support multiple switch/LED loads. For safety-critical modules, migrate to AEC-Q100-qualified PIC16F parts; the PIC16F877A itself is not AEC-Q100 qualified.
Được đề xuất
Low-Cost Instrumentation
The PIC16F877A-E/L drives low-cost bench instruments such as panel meters, function generators, and signal analyzers using its PWM modules to synthesize waveforms and its 10-bit ADC to digitize measurements. Its UART enables USB-to-serial interface bridges for PC connectivity. The 14 KB Flash stores lookup tables and calibration data, simplifying firmware updates.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho PIC16F877A-E/L — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | PIC16F877-20/L | PIC16F871-E/L | PIC18F458-E/L | PIC16F877A-I/L |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 44-pin PLCC (J-lead) | 44-pin PLCC - same | 44-pin PLCC - same | 44-pin PLCC - same | 44-pin PLCC - same |
| Core | PIC16 (8-bit, 14-bit instruction) | PIC16 - same | PIC16 - same | PIC18 (16-bit instruction) | PIC16 - same |
| Program Memory (Flash) | 14 KB Flash | ROM (one-time programmable) | 13 KB Flash | 32 KB Flash | 14 KB Flash |
| Data Memory (SRAM) | 368 bytes | 368 bytes | 368 bytes | 1536 bytes | 368 bytes |
| Maximum Clock Frequency | 20 MHz | 20 MHz | 20 MHz | 40 MHz | 20 MHz |
| Operating Temperature | -40 C to +125 C (Extended) | 0 C to +70 C (Commercial) | -40 C to +125 C (Extended) | -40 C to +125 C (Extended) | -40 C to +85 C (Industrial) |
| ADC Channels | 8 x 10-bit | 8 x 10-bit | 5 x 10-bit | 8 x 10-bit | 8 x 10-bit |
Bảo phân biệt quan trọng
- Extended temperature grade for industrial/automotive environments (vsPIC16F877A-I/L)
- Decades of design heritage and reference material (vsPIC16F887-I/L)
- More ADC channels than PIC16F871 (vsPIC16F871-E/L)
Ghi chú thiết kế
Place 100 nF ceramic decoupling capacitors as close as possible to each VDD/AVDD pin (pins 11 and 32), plus a 10 uF bulk capacitor near the MCU. VSS pins (12 and 31) must both be returned to a common low-impedance ground plane. Estimated: the PIC16F877A typically draws 5-15 mA active at 20 MHz and 5 V; the brown-out reset (BOR) is configurable via the configuration word to assert below 4.0 V.
The PLCC-44 package uses J-leads and accepts through-hole sockets that simplify programming and rework. Use a PLCC-44 socket (e.g., 3M Textool) on development boards. Estimated: keep the MCLR pull-up (typically 10 kohm) within 5 mm of pin 1 to avoid spurious resets; route the PGC/PGD ICD signals (RB6/RB7) away from switching traces to preserve debug signal integrity.
Do not leave MCLR floating - always tie it to VDD through a 10 kohm pull-up or directly if hardware reset is not needed. Watchdog timer must be disabled in configuration or cleared in software to avoid unintended resets. The internal oscillator (INTOSC) saves an external crystal but limits timing accuracy to roughly 2%, which is insufficient for UART communication without calibration.
Thông tin tuân thủ
RoHS compliance verified from Microchip product page. PIC16F877A-E/L is not AEC-Q100 qualified; for AEC-Q100 automotive, use PIC16F877A-E/L equivalent devices in the Microchip automotive portfolio.
