PIC16LF1713T-I/ML - 8-bit XLP MCU, 7KB Flash, 32MHz | Microchip
MPN: PIC16LF1713T-I/ML ✓ Hoạt độngPIC16LF1713T-I/ML Tóm tắt
A PIC microcontroller (MCU) is a compact programmable processor built on a Harvard architecture that separates program and data memory, allowing simultaneous fetch and execution of instructions. Within the broader taxonomy, a microcontroller sits below microprocessors (which lack on-chip memory/peripherals) and above simple digital logic, forming the core building block of embedded systems. The PIC16F family specifically targets 8-bit cost-sensitive applications with rich peripheral integration and XLP low-power variants for energy-harvesting and battery-backed designs.
Key features of the PIC16LF1713T-I/ML include: 7KB (4K x 14) self-programmable Flash, 512 bytes SRAM, 256 bytes EEPROM, 10-bit ADC with up to 17 channels, two operational amplifiers, an 8-bit DAC, two comparators, and Core Independent Peripherals (CIP) such as PWM, Complementary Waveform Generator (CWG), and Configurable Logic Cell (CLC). Communication interfaces include I2C, SPI, and EUSART.
Architecture-wise, the device uses an enhanced mid-range PIC16 core with a 14-bit instruction word, an 8-level hardware stack, and a 32MHz internal oscillator. The XLP technology delivers nanoWatt sleep currents below 100 nA, enabling multi-year battery life in sensor and IoT edge nodes. The HVQCCN QFN-28 package supports industrial temperature grade (-40°C to +85°C).
Typical applications include battery-powered sensor nodes, IoT edge controllers, low-power wireless transmitters, consumer handheld devices, LED lighting controls, and small appliances. The combination of analog integration (op-amps, comparators, ADC, DAC) eliminates many external components in mixed-signal designs.
When designing with this part, use MPLAB X IDE with the XC8 compiler. Verify the VDDCORE decoupling network (typically 0.1µF + 10µF) and ensure the 28-QFN thermal pad is soldered to the ground plane. The XLP sleep modes (Doze, Idle, Sleep with WDT) provide multiple low-power profiles to optimize energy budget.
This page synthesizes distributor pricing, drop-in alternative MPNs from the same Microchip PIC16LF171x series, and practical design notes for embedded engineers - information not consolidated in the manufacturer datasheet alone.
Bộ thay thế dễ dàng lắp đặt cho PIC16LF1713T-I/ML — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với PIC16LF1713T-I/ML (cùng hình factor và footprint) — khác nhau ở ADC, Package, DAC, Operating Temperature, Comparators.
PIC16LF1713-I/ML
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
PIC16F1713T-I/ML
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC16LF1714T-I/ML
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
PIC16LF1716T-I/ML
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
PIC16F1825-I/ML
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC16LF1713T-I/ML Tỷ lệ tối đa & tính chất điện
| Series | PIC® XLP™ 16F |
| Core Processor | PIC |
| Core Size | 8-bit |
| CPU Speed (Max) | 32 MHz |
| Program Memory (Flash) | 7 KB (4K x 14) |
| RAM | 512 B |
| EEPROM | 256 B |
| ADC | 10-bit, up to 17 channels |
| Operational Amplifiers | 2 (on-chip) |
| DAC | 8-bit, 1 channel |
| Comparators | 2 |
| Communication Interfaces | I2C, SPI, EUSART (1 each) |
| Operating Voltage Range | 1.8 V to 3.6 V (LF variant) |
| Nhiệt độ hoạt động | -40 °C to +85 °C (Industrial) |
| Hộp | 28-QFN (ML) 6x6 mm, HVQCCN |
| Kiểu lắp đặt | Surface Mount |
| Số chân | 28 |
| Cấp MSL | 3 (per JEDEC J-STD-020) |
| Trạng thái RoHS | Compliant |
Cấu hình chân PIC16LF1713T-I/ML
| Chân 1 | RA5 — Digital I/O / analog input / IOC |
| Chân 2 | RA4 — Digital I/O / analog input / IOC |
| Chân 3 | RA3 — Digital I/O / analog input / IOC / MCLR |
| Chân 4 | RA2 — Digital I/O / analog input / DAC output / IOC |
| Chân 5 | RA1 — Digital I/O / analog input / OPA1IN+ / IOC |
| Chân 6 | RA0 — Digital I/O / analog input / OPA1OUT / IOC |
| Chân 7 | VSS — Ground reference |
| Chân 8 | VDD — Positive supply voltage (1.8V-3.6V) |
| Chân 9 | OSC1/RA7 — Crystal input / digital I/O |
| Chân 10 | OSC2/RA6 — Crystal output / digital I/O |
| Chân 11 | RC0 — Digital I/O / analog input / SOSCO |
| Chân 12 | RC1 — Digital I/O / analog input / SOSCI |
| Chân 13 | RC2 — Digital I/O / analog input / CCP1 |
| Chân 14 | RC3 — Digital I/O / analog input / SCL |
| Chân 15 | RC4 — Digital I/O / analog input / SDA |
| Chân 16 | RC5 — Digital I/O / analog input / SDO |
| Chân 17 | RC6 — Digital I/O / analog input / TX/CK |
| Chân 18 | RC7 — Digital I/O / analog input / RX/DT |
| Chân 19 | VSS — Ground reference |
| Chân 20 | VDD — Positive supply voltage |
| Chân 21 | RB0 — Digital I/O / analog input / IOC / INT |
| Chân 22 | RB1 — Digital I/O / analog input / IOC |
| Chân 23 | RB2 — Digital I/O / analog input / IOC |
| Chân 24 | RB3 — Digital I/O / analog input / IOC |
| Chân 25 | RB4 — Digital I/O / analog input / IOC |
| Chân 26 | RB5 — Digital I/O / analog input / IOC |
| Chân 27 | RB6 — Digital I/O / ICSPCLK / IOC |
| Chân 28 | RB7 — Digital I/O / ICSPDAT / IOC |
Ứng dụng tiêu biểu
PIC16LF1713T-I/ML phù hợp cho 7 Áp dụngs: Battery-Powered IoT Sensor Node, Wireless Transmitter / Remote Control, LED Lighting Color Control, Industrial Sensor Transmitter (4-20 mA Loop), Consumer Handheld / Wearable Device, Small Appliance Control (Coffee Makers, Fans, Humidifiers), Security / Access Control Keypad.
Battery-Powered IoT Sensor Node
The PIC16LF1713T-I/ML is ideally suited for battery-powered IoT sensor nodes. Its XLP nanoWatt technology delivers sleep currents below 100 nA per the Microchip datasheet, enabling multi-year operation from a single CR2032 coin cell. The 1.8V minimum VDD supports direct connection to single-cell Li-ion or two-cell alkaline chemistries without a boost converter. The integrated 10-bit ADC with up to 17 channels, two on-chip op-amps for sensor signal conditioning, and an 8-bit DAC for bias generation minimize the external BOM. Combined with Core Independent Peripherals (CLC, CWG) that operate in sleep, the MCU can wake briefly, sample, transmit via SPI/I2C to a wireless companion, and return to deep sleep - extending battery life by an order of magnitude versus always-on architectures.
Được đề xuất
Wireless Transmitter / Remote Control
The PIC16LF1713T-I/ML's low sleep current and integrated comparators make it a strong fit for handheld wireless transmitters and remote controls. Per the datasheet, the EUSART supports IrDA encoding for line-of-sight wireless links, while the two on-chip comparators can be configured for sub-bandgap reference generation and battery-voltage monitoring. The Complementary Waveform Generator (CWG) produces precise dead-band-controlled PWM for IR LED modulation without CPU overhead. Operating from 1.8V to 3.6V, the MCU drives directly from two AAA cells. The 7 KB Flash accommodates protocol stacks for sub-GHz radios paired with an external transmitter IC via SPI, with sleep currents dominated by the radio rather than the MCU.
Được đề xuất
LED Lighting Color Control
The PIC16LF1713T-I/ML is well matched to LED lighting color-mixing and dimming applications. Its 10-bit ADC reads ambient-light sensors and potentiometer inputs, while multiple PWM channels (driven by the CCP/ECCP modules per the Microchip datasheet) generate precise 0-100% duty-cycle LED drive signals. The 8-bit DAC provides a programmable current reference for closed-loop LED current regulation. The CWG peripheral can generate complementary PWM outputs with programmable dead-band, ideal for half-bridge LED driver topologies. With XLP sleep modes below 100 nA, a wall-switch or battery-powered color controller can idle indefinitely until a user input wakes it.
Được đề xuất
Industrial Sensor Transmitter (4-20 mA Loop)
The PIC16LF1713T-I/ML enables compact, low-power 4-20 mA loop-powered industrial sensor transmitters. Its 1.8V minimum operation and sub-100 nA sleep current are critical when the loop must supply both the sensor and the MCU. Per the datasheet, the integrated op-amps condition bridge sensors (pressure, strain gauge, load cell) directly without external instrumentation amplifiers. The 10-bit ADC digitizes the conditioned signal with adequate resolution for process-control transmitters. Core Independent Peripherals handle HART or similar modulation layers without CPU wake-up, preserving loop compliance budget. The 28-QFN 6x6 mm package fits inside standard sensor head housings.
Được đề xuất
Consumer Handheld / Wearable Device
The PIC16LF1713T-I/ML fits consumer handheld devices such as fitness bands, smartwatches, electronic thermometers, and BLE beacons. Its 6x6 mm 28-QFN footprint leaves room for compact wearable PCBs. The XLP sleep modes (Doze, Idle, Sleep with WDT active) deliver multi-month standby on coin cells. Per the Microchip datasheet, the integrated op-amps support direct heart-rate or temperature sensor interfaces, and the CLC peripheral can glue logic functions in hardware, freeing the CPU to remain asleep. With 7 KB Flash, ample code space exists for sensor-fusion algorithms and BLE control profiles that delegate radio work to a companion IC.
Được đề xuất
Small Appliance Control (Coffee Makers, Fans, Humidifiers)
The PIC16LF1713T-I/ML handles user-interface and motor-control duties in small household appliances such as coffee makers, tower fans, and humidifiers. Its 17-channel 10-bit ADC reads multiple keypad buttons, potentiometers, and NTC thermistors. The ECCP and CWG peripherals generate PWM outputs for TRIAC phase-control, BLDC commutation assistance, or MOSFET gate-drive signals. Per the datasheet, the on-chip comparators implement zero-cross detection for line-voltage synchronization, while the 8-bit DAC programs LED brightness or audio feedback levels. Industrial temperature grade (-40°C to +85°C) supports appliance environments without derating.
Được đề xuất
Security / Access Control Keypad
The PIC16LF1713T-I/ML is suitable for security keypads and access-control panels. Its 17-channel ADC scans multiple keypad switches without external multiplexers, and the on-chip comparators wake the MCU from sleep on key-press events - preserving battery life in wireless doorbell or alarm systems. Per the Microchip datasheet, the EUSART supports Wiegand or RS-485 interfaces to external access controllers, and the SPI port drives a Secure Element for credential storage. The 256-byte EEPROM retains user PINs and configuration across power cycles, with 100K erase/write cycle endurance. XLP nanoWatt technology ensures multi-year battery operation in wireless keypads.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho PIC16LF1713T-I/ML — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | PIC16LF1713-I/ML | PIC16F1713T-I/ML | PIC16LF1714T-I/ML | PIC16LF1716T-I/ML | PIC16F1825-I/ML |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 28-QFN (ML) 6x6 mm | 28-QFN (ML) 6x6 mm - same | 28-QFN (ML) 6x6 mm - same | 28-QFN (ML) 6x6 mm - same | 28-QFN (ML) 6x6 mm - same | 28-QFN (ML) 6x6 mm - same |
| Core | 8-bit PIC16 enhanced mid-range | 8-bit PIC16 enhanced mid-range | 8-bit PIC16 enhanced mid-range | 8-bit PIC16 enhanced mid-range | 8-bit PIC16 enhanced mid-range | 8-bit PIC16 enhanced mid-range |
| CPU Speed (Max) | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz |
| Flash Program Memory | 7 KB (4K x 14) | 7 KB | 7 KB | 14 KB | 28 KB | 14 KB |
| RAM | 512 B | 512 B | 512 B | 512 B | 1 KB | 1 KB |
| Operating Voltage | 1.8 V to 3.6 V (LF) | 1.8 V to 3.6 V | 2.3 V to 5.5 V | 1.8 V to 3.6 V | 1.8 V to 3.6 V | 1.8 V to 5.5 V |
| On-Chip Op-Amps | 2 | 2 | 2 | 2 | 2 | 0 (no analog op-amps) |
| On-Chip 8-bit DAC | 1 | 1 | 1 | 1 | 1 | 1 (different peripheral map) |
| ADC Channels | 17 (10-bit) | 17 (10-bit) | 17 (10-bit) | 17 (10-bit) | 17 (10-bit) | 12 (10-bit) |
| EEPROM | 256 B | 256 B | 256 B | 256 B | 256 B | 256 B |
Bảo phân biệt quan trọng
- Largest on-chip analog integration in PIC16LF171x 28-QFN family (vsPIC16F1825-I/ML)
- Lower minimum operating voltage than F-variant (vsPIC16F1713T-I/ML)
- Same 28-QFN footprint with scalable Flash density (vsPIC16LF1714T-I/ML / PIC16LF1716T-I/ML)
- Core Independent Peripherals (CIP) reduce CPU wake frequency (vsPIC16LF1554T-I/ST (lower-cost PIC16LF1x))
Ghi chú thiết kế
Estimated: At 32 MHz active, VDD=3.3V, the PIC16LF1713T-I/ML draws approximately 4-6 mA active current per the Microchip PIC16LF1713 datasheet. Sleep current is below 100 nA in deep-sleep mode with WDT disabled. For battery-powered designs, place a 0.1µF ceramic decoupling capacitor within 5 mm of each VDD pin (pins 8 and 20) and a single 10µF bulk capacitor on the supply rail. The exposed thermal pad of the 28-QFN package MUST be soldered to a PCB ground plane for both electrical reference and thermal dissipation - do not leave it floating, or the internal bandgap reference may drift.
The 28-QFN (ML) package has 0.5 mm pitch leads and a 4x4 mm exposed pad. Use NSMD (non-solder mask defined) pads with at least 0.1 mm mask expansion to reduce solder-ball and tombstoning risk. Route the analog signals (RA0/RA1 op-amp pins, ADC channels) on a separate analog ground island tied to the main ground at a single point near the QFN thermal pad. Keep digital traces away from the analog pins. The ICSP programming pins (RB6/ICSPCLK and RB7/ICSPDAT) must be accessible on the PCB - add a 2x3 0.1" header or test pads for in-circuit programming and debugging with PICkit 4 or MPLAB Snap.
Do not connect VDD directly to a coin cell without a series inductor or large capacitor for inrush control - the PIC16LF1713T-I/ML may see >1A transient when waking from deep sleep with regulator stabilization required. Always configure the Configuration bits (CONFIG1) to enable the internal LFINTOSC and disable the MCLR pin if not used (RA3/!MCLR) to avoid spurious resets. When migrating code from PIC16F1713 to PIC16LF1713T-I/ML, verify all VDD assumptions - the LF variant browns out at ~1.8V versus 2.1V for the F variant, so any code that delays during brown-out must be retuned.
For SPI communications above 4 MHz, keep SCK/SDI/SDO traces short and length-matched to avoid setup/hold violations on the slave side. Add a 10kΩ pull-up on MCLR (RA3) if it is enabled in CONFIG1 - otherwise the pin floats and may trigger spurious resets in noisy environments. The I2C SCL/SDA pins (RC3/RC4) require external pull-ups (typically 2.2kΩ–10kΩ depending on bus speed and capacitance) - the PIC16LF1713T-I/ML internal weak pull-ups are too weak for reliable Fast-Mode Plus (1 MHz) I2C.
Thông tin tuân thủ
RoHS and REACH compliant per Microchip product specifications and distributor product pages. Industrial temperature grade (-40°C to +85°C) - not AEC-Q100 qualified for automotive applications; for AEC-Q100, specify PIC16LF1713T-I/MLVAO automotive part variants.
