PIC18C858-I/PT - 8-bit 40MHz 32KB EPROM MCU w/ CAN | Microchip
MPN: PIC18C858-I/PT ✗ Cuối đờiPIC18C858-I/PT Tóm tắt
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, working RAM, and programmable I/O peripherals. The PIC18C family uses Microchip's enhanced 8-bit RISC architecture with C-compiler-optimized instruction set, linear program memory addressing up to 32 Kbytes, and linear data memory addressing up to 4 Kbytes, making it suitable for embedded control applications that need deterministic real-time response.
Key features of the PIC18C858-I/PT include a 10-bit Analog-to-Digital Converter (ADC) with multiple input channels, an integrated CAN 2.0B module for automotive and industrial networking, USART, MSSP (SPI/I2C), and capture/compare/PWM peripherals. Its 40MHz clock delivers up to 10 MIPS of processing throughput, and the 68 I/O pins give designers ample headroom for keypad, LCD, sensor, and actuator interfaces.
Architecturally, the PIC18C858 uses Harvard bus architecture with separate program and data paths, an 8-bit data path, and a 16-bit instruction word. This separation allows simultaneous instruction fetch and data access, eliminating the von Neumann bottleneck. The integrated CAN peripheral provides hardware message filtering and acceptance masks, freeing the CPU from bit-stuffing tasks.
Typical applications include industrial automation controllers, automotive body and chassis ECUs, CAN-based sensor networks, building automation gateways, and embedded control systems that benefit from the integrated CAN bus. The wide operating voltage range and industrial temperature grade also support process-control installations and HVAC controllers.
When designing with this device, remember that the PIC18C858 is built on EPROM (erasable programmable read-only memory) technology and is one-time programmable (OTP) in production. The part is marked Not Recommended for new designs by Microchip, so consider flash-based successors like the PIC18F8525 for new development. Engineers should verify the ICSP programming interface and oscillator startup timing during bring-up.
Bộ thay thế dễ dàng lắp đặt cho PIC18C858-I/PT — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với PIC18C858-I/PT (cùng hình factor và footprint) — khác nhau ở Package, Operating Temperature, ADC, Core Architecture, Program Memory Type.
PIC18C658-I/PT
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC18F8525-I/PT
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC18C858T-I/PT
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC18C858-E/PT
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC18C801-I/PT
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC18C858-I/PT Tỷ lệ tối đa & tính chất điện
| Core Architecture | PIC 8-bit RISC |
| Core Clock Speed | 40 MHz (max) |
| Program Memory Type | EPROM (OTP) |
| Program Memory Size | 32 KB (16K x 16) |
| RAM Size | 1.5 KB |
| Data Memory Addressing | Up to 4 KB (linear) |
| I/O Pin Count | 68 |
| Điện áp cung cấp | 4.2 V to 5.5 V |
| Nhiệt độ hoạt động | -40 C to +85 C (Industrial) |
| Hộp | 80-pin TQFP (PT) |
| Kiểu lắp đặt | Surface Mount |
| ADC | 10-bit |
| CAN Module | Integrated CAN 2.0B |
| Peripherals | USART, MSSP (SPI/I2C), CCP/PWM |
Cấu hình chân PIC18C858-I/PT
| Chân 1 | OSC1/CLKI — Oscillator input / external clock input |
| Chân 2 | OSC2/CLKO — Oscillator output |
| Chân 3 | MCLR/VPP — Master clear reset / programming voltage |
| Chân 4 | RA0/AN0 — PORTA bit 0 / analog input 0 |
| Chân 5 | RA1/AN1 — PORTA bit 1 / analog input 1 |
| Chân 6 | RA2/AN2/VREF- — PORTA bit 2 / analog input 2 / ADC VREF- |
| Chân 7 | RA3/AN3/VREF+ — PORTA bit 3 / analog input 3 / ADC VREF+ |
| Chân 8 | RA4/T0CKI — PORTA bit 4 / Timer0 clock input |
| Chân 9 | RA5/AN4 — PORTA bit 5 / analog input 4 |
| Chân 10 | VSS — Ground reference |
| Chân 11 | VDD — Positive supply (4.2V-5.5V) |
| Chân 12 | RB0/INT0 — PORTB bit 0 / external interrupt 0 |
| Chân 13 | RB1/INT1 — PORTB bit 1 / external interrupt 1 |
| Chân 14 | RB2/INT2 — PORTB bit 2 / external interrupt 2 |
| Chân 15 | RB3/INT3 — PORTB bit 3 / external interrupt 3 |
| Chân 16 | RB4 — PORTB bit 4 |
| Chân 17 | RB5 — PORTB bit 5 |
| Chân 18 | RB6/PGC — PORTB bit 6 / ICSP clock |
| Chân 19 | RB7/PGD — PORTB bit 7 / ICSP data |
| Chân 20 | VSS — Ground reference |
| Chân 21 | VDD — Positive supply |
| Chân 22 | RC0/T1CKI — PORTC bit 0 / Timer1 clock input |
| Chân 23 | RC1/CCP2 — PORTC bit 1 / Capture/Compare/PWM 2 |
| Chân 24 | RC2/CCP1 — PORTC bit 2 / Capture/Compare/PWM 1 |
| Chân 25 | RC3/SCK/SCL — PORTC bit 3 / SPI clock / I2C clock |
| Chân 26 | RC4/SDI/SDA — PORTC bit 4 / SPI data in / I2C data |
| Chân 27 | RC5/SDO — PORTC bit 5 / SPI data out |
| Chân 28 | RC6/TX/CK — PORTC bit 6 / USART TX / clock |
| Chân 29 | RC7/RX/DT — PORTC bit 7 / USART RX / data |
| Chân 30 | RD0/PSP0 — PORTD bit 0 / parallel slave port data 0 |
| Chân 31 | RD1/PSP1 — PORTD bit 1 / parallel slave port data 1 |
| Chân 32 | RD2/PSP2 — PORTD bit 2 / parallel slave port data 2 |
| Chân 33 | RD3/PSP3 — PORTD bit 3 / parallel slave port data 3 |
| Chân 34 | RD4/PSP4 — PORTD bit 4 / parallel slave port data 4 |
| Chân 35 | RD5/PSP5 — PORTD bit 5 / parallel slave port data 5 |
| Chân 36 | RD6/PSP6 — PORTD bit 6 / parallel slave port data 6 |
| Chân 37 | RD7/PSP7 — PORTD bit 7 / parallel slave port data 7 |
| Chân 38 | VSS — Ground reference |
| Chân 39 | VDD — Positive supply |
| Chân 40 | RE0/RD — PORTE bit 0 / parallel slave port read |
| Chân 41 | RE1/WR — PORTE bit 1 / parallel slave port write |
| Chân 42 | RE2/CS — PORTE bit 2 / parallel slave port chip select |
| Chân 43 | RF0 — PORTF bit 0 |
| Chân 44 | RF1 — PORTF bit 1 |
| Chân 45 | RF2 — PORTF bit 2 |
| Chân 46 | RF3 — PORTF bit 3 |
| Chân 47 | RF4 — PORTF bit 4 |
| Chân 48 | RF5 — PORTF bit 5 |
| Chân 49 | RF6 — PORTF bit 6 |
| Chân 50 | RF7 — PORTF bit 7 |
| Chân 51 | VSS — Ground reference |
| Chân 52 | VDD — Positive supply |
| Chân 53 | RG0 — PORTG bit 0 |
| Chân 54 | RG1 — PORTG bit 1 |
| Chân 55 | RG2 — PORTG bit 2 |
| Chân 56 | RG3 — PORTG bit 3 |
| Chân 57 | RG4 — PORTG bit 4 |
| Chân 58 | AVDD — Analog positive supply |
| Chân 59 | AVSS — Analog ground |
| Chân 60 | CANTX — CAN bus transmit output |
| Chân 61 | CANRX — CAN bus receive input |
| Chân 62 | VSS — Ground reference |
| Chân 63 | VDD — Positive supply |
| Chân 64 | RH0 — PORTH bit 0 (external memory bus) |
| Chân 65 | RH1 — PORTH bit 1 (external memory bus) |
| Chân 66 | RH2 — PORTH bit 2 (external memory bus) |
| Chân 67 | RH3 — PORTH bit 3 (external memory bus) |
| Chân 68 | RH4 — PORTH bit 4 (external memory bus) |
| Chân 69 | RH5 — PORTH bit 5 (external memory bus) |
| Chân 70 | RH6 — PORTH bit 6 (external memory bus) |
| Chân 71 | RH7 — PORTH bit 7 (external memory bus) |
| Chân 72 | VSS — Ground reference |
| Chân 73 | VDD — Positive supply |
| Chân 74 | RJ0 — PORTJ bit 0 (external memory bus) |
| Chân 75 | RJ1 — PORTJ bit 1 (external memory bus) |
| Chân 76 | RJ2 — PORTJ bit 2 (external memory bus) |
| Chân 77 | RJ3 — PORTJ bit 3 (external memory bus) |
| Chân 78 | RJ4 — PORTJ bit 4 (external memory bus) |
| Chân 79 | RJ5 — PORTJ bit 5 (external memory bus) |
| Chân 80 | RJ6 — PORTJ bit 6 (external memory bus) |
Ứng dụng tiêu biểu
PIC18C858-I/PT phù hợp cho 6 Áp dụngs: Industrial CAN Network Node, Automotive Body Control Module, Building Automation Gateway, Process Control Sensor Hub, HVAC Controller Board, Embedded CAN-to-Serial Bridge.
Industrial CAN Network Node
The PIC18C858-I/PT is purpose-built for industrial CAN network nodes thanks to its integrated CAN 2.0B module with hardware acceptance filtering. At 40MHz it delivers 10 MIPS, comfortably handling CAN 2.0B message processing at 1 Mbps alongside sensor sampling via the 10-bit ADC. The 68 I/O pins connect directly to digital sensors, opto-isolated inputs, and relay drivers typical of industrial control cabinets. Placed on a CAN bus backbone with a TJA1050 transceiver, it forms a slave node reading field sensors and broadcasting status frames. The 4.2-5.5V supply matches 5V industrial rails directly. Trade-off: EPROM requires pre-programmed parts - consider PIC18F8525 for field-updateable firmware.
Được đề xuất
Automotive Body Control Module
Automotive body control modules benefit from the PIC18C858-I/PT's combination of 32KB EPROM, integrated CAN, and 68 I/O pins. Window, mirror, lighting, and door-lock actuators can be driven directly through high-current I/O ports while CAN connectivity links the BCM to the vehicle bus. The 10-bit ADC reads switch and sensor inputs for debounced control decisions. Operating from a regulated 5V rail with industrial temperature rating, it suits under-dash automotive environments. The CAN hardware filtering offloads message routing from the CPU, leaving cycles for body-control logic. Note: For safety-critical systems requiring ASIL compliance, pair with an external watchdog and consider newer PIC18F variants with functional safety documentation.
Được đề xuất
Building Automation Gateway
Building automation gateways bridge HVAC, lighting, and security subsystems using the PIC18C858-I/PT's CAN module plus USART and MSSP peripherals. The 32KB EPROM stores gateway routing tables and protocol converters, while 1.5KB RAM handles message buffering. The 68 I/O pins drive status LEDs, keypads, and LCD displays common to building controllers. Running at 40MHz it converts between BACnet, Modbus, and CAN protocols in real time. The 5V supply matches typical building-automation backplane rails, and the -40C to +85C industrial range covers mechanical-room environments. Trade-off: EPROM programming requires a parallel programmer at production - the PIC18F8525-I/PT offers ICSP for in-the-field firmware updates.
Được đề xuất
Process Control Sensor Hub
Process control sensor hubs use the PIC18C858-I/PT to aggregate multiple analog and digital sensors and broadcast readings over CAN. The 10-bit ADC multiplexes across multiple process variables (temperature, pressure, flow), while the integrated CAN module transmits standardized frames to a central PLC. The 68 I/O pins accommodate digital sensor arrays plus HMI keypad input. At 10 MIPS the MCU handles linearization math, calibration lookups, and CAN protocol stack simultaneously. The 4.2-5.5V supply operates from a 5V regulated industrial rail. The wide temperature range supports outdoor and factory-floor deployments. Compared to a discrete ADC + microcontroller solution, this integrated part reduces BOM count and PCB footprint.
Được đề xuất
HVAC Controller Board
HVAC controller boards leverage the PIC18C858-I/PT for fan, compressor, and valve control loops. The CCP/PWM peripherals generate variable-speed drive signals for brushless DC fans, while the ADC reads temperature sensors from multiple zones. The integrated CAN bus links indoor units to the building management system. With 32KB of program memory, control loop firmware plus scheduling logic fits comfortably. The 1.5KB RAM handles setpoint storage and PID working variables. Operating from a 5V supply with industrial temperature grade, the MCU suits rooftop unit and air-handler installations. For new designs, migrate to PIC18F8525-I/PT to gain flash reprogrammability and field firmware updates.
Được đề xuất
Embedded CAN-to-Serial Bridge
A CAN-to-serial bridge application uses the PIC18C858-I/PT to convert between CAN 2.0B frames and RS-232/RS-485 serial traffic for legacy equipment integration. The CAN peripheral handles incoming automotive or industrial frames, while the USART drives the serial port at programmable baud rates. The MSSP peripheral can additionally support SPI-to-CAN bridging. With 68 I/O pins, status LEDs and configuration switches fit alongside the comms interfaces. The 32KB EPROM holds the protocol-conversion state machine and configuration tables. Operating at 40MHz the bridge sustains full-duplex serial plus 1 Mbps CAN without frame drops. Trade-off: For high-throughput bridging with multi-message buffering, the larger RAM on PIC18F8525 is preferable.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho PIC18C858-I/PT — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | PIC18C658-I/PT | PIC18F8525-I/PT | PIC18C858T-I/PT | PIC18C858-E/PT | PIC18C801-I/PT |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | TQFP-80 (PT) | TQFP-80 (PT) - same | TQFP-80 (PT) - same | TQFP-80 (PT) - same | TQFP-80 (PT) - same | TQFP-80 (PT) - same |
| Program Memory | 32 KB EPROM | 16 KB EPROM (-50%) | 32 KB Flash (same size, in-system programmable) | 32 KB EPROM (same) | 32 KB EPROM (same) | 0 KB (external memory only) |
| RAM Size | 1.5 KB | 1.5 KB (same) | 4 KB (+167%) | 1.5 KB (same) | 1.5 KB (same) | 1.5 KB (same) |
| Memory Type | EPROM (OTP) | EPROM (OTP) | Flash (in-system programmable) | EPROM (OTP) | EPROM (OTP) | External memory only |
| Core Clock Speed | 40 MHz | 40 MHz (same) | 40 MHz (same) | 40 MHz (same) | 40 MHz (same) | 40 MHz (same) |
| CAN Module | Yes (integrated CAN 2.0B) | Yes (integrated CAN 2.0B) | Yes (integrated CAN 2.0B) | Yes (integrated CAN 2.0B) | Yes (integrated CAN 2.0B) | No (external memory only) |
| Operating Temperature | -40 C to +85 C (Industrial) | -40 C to +85 C (Industrial) | -40 C to +85 C (Industrial) | -40 C to +85 C (Industrial) | -40 C to +125 C (Extended) | -40 C to +85 C (Industrial) |
Bảo phân biệt quan trọng
- Integrated CAN 2.0B peripheral with hardware filtering (vsPIC18C801-I/PT)
- 32 KB EPROM program memory (vsPIC18C658-I/PT)
- Flash-based successor path with same peripherals (vsPIC18F8525-I/PT)
Ghi chú thiết kế
The PIC18C858-I/PT operates from a single 4.2V to 5.5V supply. Place a 100nF decoupling capacitor close to each VDD pin (multiple VDD pins on the TQFP-80 package) and a bulk 10uF tantalum or ceramic capacitor on the board supply rail. Use separate analog (AVDD) and digital (VDD) supplies tied together at a single point near the IC if the ADC is in use, with a ferrite bead to reduce digital switching noise coupling into analog measurements.
The PIC18C858 uses EPROM (OTP) memory, so firmware must be fully validated before production programming. Unlike flash-based PIC18F variants, there is no in-circuit reprogramming option. Engineers should prototype on a flash-based equivalent (e.g., PIC18F8525-I/PT) to avoid scrapping EPROM parts during firmware iteration. The part is also marked NRND (Not Recommended for new designs) by Microchip - verify the end product's lifecycle support window before committing to this part in long-life designs.
Route the CANRX and CANTX pins to the CAN transceiver (e.g., TJA1050) using a matched-impedance differential pair, keeping the traces short and away from switching nodes. Place the oscillator crystal as close to OSC1/OSC2 as possible with ground guard traces. The 80-pin TQFP package has a thermal pad - solder it to a ground copper pour for improved thermal dissipation, especially at 40MHz operation. Avoid running noisy digital signals parallel to analog inputs to minimize ADC crosstalk.
Thông tin tuân thủ
RoHS, REACH, and lead-free status not explicitly provided in the verified web data. PIC18C858 is an older EPROM-based MCU (introduced ~1999), predating many modern compliance certifications. Marked NRND (Not Recommended for new designs) by Microchip as of 2026-09-26.
