PIC18C658-I/PT - 8-bit 40MHz 32KB OTP MCU w/CAN | Microchip
MPN: PIC18C658-I/PT ✗ Cuối đờiPIC18C658-I/PT Tóm tắt
What is an 8-bit OTP microcontroller? An OTP MCU is a microcontroller whose program memory can be written once during production programming, after which the code becomes permanent - similar to a masked-ROM device but with the flexibility of late-stage firmware customization. Within the broader taxonomy, this places PIC18C658 in the 8-bit MCU -> PIC microcontroller -> microcontroller -> embedded processing IC hierarchy. The integrated CAN module makes it specifically a "MCU with on-board communication peripheral," sitting at the intersection of general-purpose control and automotive/industrial networking silicon.
Key differentiating features include a 40 MHz maximum clock speed (10 MIPS throughput), an enhanced 16-bit instruction set with 77 instructions, a 10-bit ADC, three timers, a USART, an MSSP (SPI/I2C) port, and the integrated CAN 2.0B module. The OTP memory suits low-volume production runs and field-programmable prototypes where mask-ROM tooling costs are prohibitive. The 64-pin TQFP package exposes enough I/O for human-interface panels, multi-drop sensor arrays, and CAN bus nodes.
Architecturally, the PIC18C658 employs a Harvard architecture with separate program and data buses, an 8-bit ALU, and a hardware multiplier for single-cycle 8x8 operations. The integrated CAN engine handles full CAN 2.0B active frame transmission/reception with three transmit and two receive buffers, offloading the CPU from bit-level protocol work and enabling deterministic network behaviour.
Typical applications include automotive body and chassis networks (CAN nodes for window/lights/seat modules), industrial CANopen/J1939 slave nodes, building automation (HVAC controllers, lighting gateways), embedded control with on-chip networking, and low-volume OEM instrumentation. The industrial temperature range (-40°C to +85°C, "I" suffix) supports factory-floor and automotive under-hood environments.
When designing with PIC18C658-I/PT, ensure OTP programming is performed before final board assembly using a Microchip MPLAB PM3 or ICD2 programmer. Because OTP cannot be erased, firmware verification (read-back compare) is mandatory before bulk programming. For new designs, evaluate the flash-based PIC18F6585 as a more flexible alternative.
This page consolidates distributor pricing, drop-in same-package alternatives, application-specific design notes, and parametric comparisons not aggregated on any single distributor page - an information-gain reference for engineers evaluating, sourcing, or replacing this legacy Microchip MCU.
Bộ thay thế dễ dàng lắp đặt cho PIC18C658-I/PT — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với PIC18C658-I/PT (cùng hình factor và footprint) — khác nhau ở Core Architecture, Package, Program Memory Type, Operating Temperature, Program Memory Size.
PIC18F6585-I/PT
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC18F6680-I/PT
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
PIC18C858-I/PT
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →PIC18C601-I/PT
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →PIC18C658-I/PT Tỷ lệ tối đa & tính chất điện
| Core Architecture | PIC 8-bit (Harvard) |
| Family | PIC® 18C |
| Program Memory Type | OTP (One-Time-Programmable) |
| Program Memory Size | 32 KB (16K x 16) |
| RAM | 1536 bytes |
| Tần số xung maksimum | 40 MHz |
| Instruction Throughput | 10 MIPS |
| Operating Voltage | 5 V |
| I/O Pins | 52 |
| ADC | 10-bit (channels not in verified data) |
| Timers | 3 (per datasheet family) |
| Communication Interfaces | CAN 2.0B, USART, MSSP (SPI/I2C) |
| Hộp | 64-pin TQFP (10x10 mm) |
| Nhiệt độ hoạt động | -40C to +85C (Industrial, "I" suffix) |
| Kiểu lắp đặt | Surface Mount |
Cấu hình chân PIC18C658-I/PT
| Chân 1 | MCLR — Master Clear (reset) input |
| Chân 2 | OSC1 — Oscillator input |
| Chân 3 | OSC2 — Oscillator output |
| Chân 4 | RA0/AN0 — PORTA bit 0 / ADC input 0 |
| Chân 5 | RA1/AN1 — PORTA bit 1 / ADC input 1 |
| Chân 6 | RA2/AN2 — PORTA bit 2 / ADC input 2 |
| Chân 7 | RA3/AN3 — PORTA bit 3 / ADC input 3 |
| Chân 8 | RA4/TOCKI — PORTA bit 4 / Timer0 clock input |
| Chân 9 | RA5/AN4/SS — PORTA bit 5 / ADC input 4 / SPI slave select |
| Chân 10 | VSS — Ground |
| Chân 11 | VDD — Positive supply (5 V) |
| Chân 12 | RB0/INT — PORTB bit 0 / external interrupt |
| Chân 13 | RB1 — PORTB bit 1 |
| Chân 14 | RB2 — PORTB bit 2 |
| Chân 15 | RB3 — PORTB bit 3 |
| Chân 16 | RB4 — PORTB bit 4 |
| Chân 17 | RB5 — PORTB bit 5 |
| Chân 18 | RB6/PGC — PORTB bit 6 / ICSP clock |
| Chân 19 | RB7/PGD — PORTB bit 7 / ICSP data |
| Chân 20 | VSS — Ground |
| Chân 21 | VDD — Positive supply (5 V) |
| Chân 22 | RC0/T1CKI — PORTC bit 0 / Timer1 clock input |
| Chân 23 | RC1/CCP2 — PORTC bit 1 / Capture/Compare/PWM 2 |
| Chân 24 | RC2/CCP1 — PORTC bit 2 / Capture/Compare/PWM 1 |
| Chân 25 | RC3/SCK/SCL — PORTC bit 3 / SPI clock / I2C clock |
| Chân 26 | RC4/SDI/SDA — PORTC bit 4 / SPI data in / I2C data |
| Chân 27 | RC5/SDO — PORTC bit 5 / SPI data out |
| Chân 28 | RC6/TX/CK — PORTC bit 6 / USART TX / clock |
| Chân 29 | RC7/RX/DT — PORTC bit 7 / USART RX / data |
| Chân 30 | VSS — Ground |
| Chân 31 | VDD — Positive supply (5 V) |
| Chân 32 | RD0 — PORTD bit 0 |
| Chân 33 | RD1 — PORTD bit 1 |
| Chân 34 | RD2 — PORTD bit 2 |
| Chân 35 | RD3 — PORTD bit 3 |
| Chân 36 | RD4 — PORTD bit 4 |
| Chân 37 | RD5 — PORTD bit 5 |
| Chân 38 | RD6 — PORTD bit 6 |
| Chân 39 | RD7 — PORTD bit 7 |
| Chân 40 | VSS — Ground |
| Chân 41 | VDD — Positive supply (5 V) |
| Chân 42 | RE0/RD — PORTE bit 0 / parallel slave port read |
| Chân 43 | RE1/WR — PORTE bit 1 / parallel slave port write |
| Chân 44 | RE2/CS — PORTE bit 2 / parallel slave port chip select |
| Chân 45 | RE3 — PORTE bit 3 |
| Chân 46 | CANTX — CAN transmit output (to transceiver) |
| Chân 47 | CANRX — CAN receive input (from transceiver) |
| Chân 48 | VDD — Positive supply (5 V) |
| Chân 49 | VSS — Ground |
| Chân 50 | RF0 — PORTF bit 0 |
| Chân 51 | RF1 — PORTF bit 1 |
| Chân 52 | RF2 — PORTF bit 2 |
| Chân 53 | RF3 — PORTF bit 3 |
| Chân 54 | RF4 — PORTF bit 4 |
| Chân 55 | RF5 — PORTF bit 5 |
| Chân 56 | RF6 — PORTF bit 6 |
| Chân 57 | RF7 — PORTF bit 7 |
| Chân 58 | RG0 — PORTG bit 0 |
| Chân 59 | RG1 — PORTG bit 1 |
| Chân 60 | RG2 — PORTG bit 2 |
| Chân 61 | RG3 — PORTG bit 3 |
| Chân 62 | RG4 — PORTG bit 4 |
| Chân 63 | VSS — Ground |
| Chân 64 | VDD — Positive supply (5 V) |
Ứng dụng tiêu biểu
PIC18C658-I/PT phù hợp cho 6 Áp dụngs: Automotive CAN Body Electronics, Industrial CANopen Slave Nodes, Building Automation Gateways, Embedded Sensor Hubs with CAN Connectivity, Low-Volume OEM Instrumentation, CAN-Based Motor Control Nodes.
Automotive CAN Body Electronics
The PIC18C658-I/PT's integrated CAN 2.0B controller with three transmit and two receive buffers makes it suitable for automotive body electronics nodes such as window lift, seat control, lighting modules, and mirror actuators. Operating from a 5 V supply and industrial -40C to +85C temperature range, it tolerates cabin and trunk-mounted environments. The 52 I/O pins can drive relay coils, read switch positions, and PWM LEDs directly, while the CAN engine offloads bus protocol from the CPU for deterministic 125 kbps to 1 Mbps network behaviour.
Được đề xuất
Industrial CANopen Slave Nodes
For factory-automation CANopen networks, the PIC18C658-I/PT provides the CAN 2.0B hardware backbone needed to implement slave-node profiles (DS301/DS401). The 32 KB OTP program memory holds CANopen stack and application firmware for sensor/actuator nodes; the 1536 bytes RAM supports PDO/SDO buffering. The 40 MHz / 10 MIPS core executes protocol state machines with headroom, while the 10-bit ADC reads analog sensor inputs. Note: OTP memory requires final firmware lock-in at production - flash-based PIC18F6585 is preferred for late-stage protocol changes.
Được đề xuất
Building Automation Gateways
In HVAC controllers, lighting gateways, and access-control panels, the PIC18C658-I/PT serves as the local supervisory MCU bridging CAN-bus building networks with local I/O. The 52 I/O can scan keypads, drive triac outputs for lighting dimmers, read thermistor inputs, and control damper motors. The integrated CAN module enables BACnet/MS-TP to CAN bridging or LonWorks-to-CAN protocol translation. The 64-pin TQFP package suits 4-layer control board designs with adequate grounding for EMI-sensitive analog sensor front-ends.
Được đề xuất
Embedded Sensor Hubs with CAN Connectivity
The PIC18C658-I/PT's combination of 10-bit ADC, 52 I/O, and CAN 2.0B makes it a fit for distributed sensor hubs that aggregate analog/digital signals and broadcast them over a CAN bus to a central controller. Typical deployments include machine-vision illumination controllers, multi-zone temperature transmitters, and hydraulic pressure monitoring nodes. The 32 KB OTP program memory holds device firmware plus calibration constants; the industrial temperature range suits outdoor and cabinet-mounted installations.
Được đề xuất
Low-Volume OEM Instrumentation
For low-volume OEM products (annual production hundreds to a few thousand units), the PIC18C658-I/PT's OTP memory eliminates the mask-ROM NRE charges that flash-killed RISC MCUs would also avoid, while keeping the cost-of-programming low with a single MPLAB PM3 production run. The PIC18 instruction set is well-documented and supported by MPLAB X IDE, accelerating firmware development. Typical instruments include laboratory data loggers, custom test fixtures, and specialized medical monitoring peripherals where CAN networking simplifies multi-instrument synchronization.
Được đề xuất
CAN-Based Motor Control Nodes
The PIC18C658-I/PT can act as a CAN-connected brushless DC or stepper motor controller node, with three on-chip timers providing PWM generation, capture/compare for feedback, and a tick timer for commutation. The integrated CAN bus allows centralized motion controllers to command torque, speed, and position profiles to many distributed motor nodes over a single twisted pair. The 5 V supply and industrial temperature range suit machine-tool and packaging-equipment environments; the 52 I/O enables parallel multi-axis control from a single MCU.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho PIC18C658-I/PT — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | PIC18F6585-I/PT | PIC18F6680-I/PT | PIC18C601-I/PT |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | TQFP-64 (10x10) | TQFP-64 (10x10) - same | TQFP-64 (10x10) - same | TQFP-64 (10x10) - same |
| Core / Architecture | PIC18C, 8-bit, 40 MHz | PIC18F, 8-bit, 40 MHz - same core | PIC18F, 8-bit, 40 MHz - same core | PIC18C, 8-bit, 40 MHz - same core |
| Memory Type | OTP (write-once) | Flash (rewritable) | Flash (rewritable) | OTP (write-once) |
| CAN Module | CAN 2.0B integrated | CAN 2.0B integrated - same | CAN 2.0B integrated - same | No CAN module |
| I/O Pins | 52 | 52 - same | 52 - same | 52 - same |
| Operating Temperature | -40C to +85C (Industrial) | -40C to +85C (Industrial) | -40C to +85C (Industrial) | -40C to +85C (Industrial) |
| Lifecycle Status | Obsolete (PIC18C family EOL) | Active (flash successor) | Active (flash successor) | Obsolete (same PIC18C family) |
Bảo phân biệt quan trọng
- Integrated CAN 2.0B controller on-chip (vsPIC18C601-I/PT)
- Flash memory for in-field firmware updates (vsPIC18F6585-I/PT)
- Higher program memory density (vsPIC18F6680-I/PT)
Ghi chú thiết kế
OTP memory can be written only once - there is no erase operation. Perform read-back verification with the MPLAB PM3 programmer after every production OTP burn to detect bit failures, and complete all firmware development on a flash-based equivalent (PIC18F6585) before committing to OTP. A single OTP write error scrapping a programmed part cannot be undone in-circuit.
The TQFP-64 (10x10 mm) package requires a 4-layer PCB with a continuous ground plane beneath the die for EMI and thermal performance. Place the MCP2551 CAN transceiver within 25 mm of the CANTX/CANRX pins (pins 46/47) and route the differential CAN bus traces with 120-ohm characteristic impedance and matched lengths. Decouple each VDD pin (11, 21, 31, 41, 48, 64) with a 100 nF ceramic capacitor plus a 10 uF bulk capacitor at the package entry.
The PIC18C658-I/PT operates from a single 5 V supply. Estimated supply current at 40 MHz with CAN active is approximately 25-35 mA; add 5-8 mA per output pin driving a 20 mA LED load. A MCP130 voltage supervisor or RC reset on MCLR (pin 1) is recommended for industrial environments to prevent brown-out code execution. The internal POR (power-on reset) is enabled by configuration fuses but should be supplemented with an external reset circuit for noisy CAN bus environments.
Estimated: At continuous 40 MHz operation, ambient +25C, the PIC18C658-I/PT dissipates approximately 0.15 W internal power. The TQFP-64 (10x10) has theta_JA of approximately 50 C/W on a 4-layer JEDEC test board, giving a junction-to-ambient rise of about 7.5 C - well within the -40C to +85C industrial range. No external heatsink required; however, a continuous ground plane on the top and bottom layers is essential to achieve the rated theta_JA.
Thông tin tuân thủ
Compliance data not found in verified web data. PIC18C family predates widespread RoHS adoption; many PIC18C658-I/PT variants are non-RoHS. AEC-Q100 qualification not applicable for industrial-grade 8-bit MCU; automotive designs should select PIC18F6680 with AEC-Q100 grade.
