PIC18LF24K22T-I/ML - 16KB Flash 8-bit MCU, 64MHz, QFN-28
MPN: PIC18LF24K22T-I/ML ✓ Hoạt độngPIC18LF24K22T-I/ML Tóm tắt
A microcontroller is the programmable central processing unit of any embedded system, combining CPU, memory, peripherals and interrupt logic on a single silicon die. Within Microchip's portfolio, the PIC18F K-series sits in the mid-range 8-bit segment above the baseline PIC16 family and below the 16-bit dsPIC and 32-bit PIC32 families. The LF sub-series denotes the low-VDD variant, while the trailing K22 denotes the 16 KB Flash tier of the PIC18F K22 family. The 'T' suffix in this MPN denotes Tape & Reel packaging and 'I/ML' specifies the industrial temperature grade (-40C to +85C) and the 28-pin ML/QFN package.
Key features include: 16 KB Flash (8K x 16), 768 B SRAM, 256 B EEPROM, 25 I/O pins, 12-bit ADC with computation features (ADC2), CTMU charge-time measurement, mTouch capacitive touch support, and nanoWatt XLP power management with multiple idle, sleep and deep-sleep modes. The integrated bootloader removes timer functionality only when the dedicated software bootloader is in use; the part otherwise offers a full suite of timers.
Typical applications include battery-powered IoT sensor nodes, wearable health and fitness electronics, low-power wireless sensor accessories, industrial sensor conditioning, USB-to-UART bridges using the EUSART, and ultra-low-power remote controls. Design consideration: the QFN-28 package requires thermal pad soldering for proper ground connectivity; the exposed pad (EP) must be soldered to the board ground plane to meet the datasheet thermal and electrical specifications.
This page synthesizes distributor pricing, drop-in alternatives within the same QFN-28 footprint, and practical low-power design notes not found in the manufacturer datasheet alone.
Bộ thay thế dễ dàng lắp đặt cho PIC18LF24K22T-I/ML — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với PIC18LF24K22T-I/ML (cùng hình factor và footprint) — khác nhau ở Package, ADC, Core Architecture, I/O Pins, Program Memory (Flash).
PIC18LF24K22-I/ML
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC18LF24K22-I/SO
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC18LF24K22-I/MV
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC18LF24K22-E/SO
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC18LF23K22T-I/ML
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC18LF23K22T-I/SO
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC18F24K22-I/ML
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC18LF24K22T-I/ML Tỷ lệ tối đa & tính chất điện
| Family | PIC18 K-series (PIC18F/LF K22) |
| Core | PIC18 8-bit RISC |
| Program Memory (Flash) | 16 KB (8K x 16) |
| Data SRAM | 768 bytes |
| Data EEPROM | 256 bytes |
| Max CPU Frequency | 64 MHz (16 MIPS) |
| Supply Voltage (VDD) | 1.8 V to 3.6 V |
| I/O Pins | 25 |
| ADC | 12-bit, up to 19 channels, ADC2 with computation |
| Comparators | 2 analog comparators |
| Timers | Four 8/16-bit timers |
| CCP/ECCP Modules | 3 |
| Communication | 2x MSSP (SPI/I2C), 2x EUSART (LIN-capable) |
| Hộp | 28-QFN (6x6 mm) with Exposed Pad |
| Nhiệt độ hoạt động | -40 C to +85 C (Industrial) |
| Kiểu lắp đặt | Surface Mount |
| Cấp MSL | 3 |
| Trạng thái RoHS | Compliant |
Cấu hình chân PIC18LF24K22T-I/ML
| Chân 1 | MCLR/RE3 — Master Clear (reset) input or digital input only on RE3 |
| Chân 2 | RA0/AN0 — Digital I/O A:0 / Analog input channel 0 |
| Chân 3 | RA1/AN1 — Digital I/O A:1 / Analog input channel 1 |
| Chân 4 | RA2/AN2 — Digital I/O A:2 / Analog input channel 2 |
| Chân 5 | RA3/AN3 — Digital I/O A:3 / Analog input channel 3 |
| Chân 6 | RA4 — Digital I/O A:4 (no analog) |
| Chân 7 | RA5/AN4 — Digital I/O A:5 / Analog input channel 4 |
| Chân 8 | RE0/AN5 — Digital I/O E:0 / Analog input channel 5 |
| Chân 9 | RE1/AN6 — Digital I/O E:1 / Analog input channel 6 |
| Chân 10 | RE2/AN7 — Digital I/O E:2 / Analog input channel 7 |
| Chân 11 | VDD — Positive supply voltage (1.8 V to 3.6 V) |
| Chân 12 | VSS — Ground reference |
| Chân 13 | RA7/OSC1 — Digital I/O A:7 / Crystal oscillator input |
| Chân 14 | RA6/OSC2 — Digital I/O A:6 / Crystal oscillator output |
| Chân 15 | RC0/SOSCO — Digital I/O C:0 / SOSC oscillator output |
| Chân 16 | RC1/SOSCI — Digital I/O C:1 / SOSC oscillator input |
| Chân 17 | RC2/CCP1 — Digital I/O C:2 / CCP1 PWM output |
| Chân 18 | RC3/SCL — Digital I/O C:3 / I2C clock (MSSP) |
| Chân 19 | RC4/SDA — Digital I/O C:4 / I2C data (MSSP) |
| Chân 20 | RC5/SDO — Digital I/O C:5 / SPI data out (MSSP) |
| Chân 21 | RC6/TX/CK — Digital I/O C:6 / EUSART TX / clock |
| Chân 22 | RC7/RX/DT — Digital I/O C:7 / EUSART RX / data |
| Chân 23 | RD0 — Digital I/O D:0 |
| Chân 24 | RD1 — Digital I/O D:1 |
| Chân 25 | RD2 — Digital I/O D:2 |
| Chân 26 | RD3 — Digital I/O D:3 |
| Chân 27 | RB0/AN8 — Digital I/O B:0 / Analog input channel 8 / interrupt-on-change |
| Chân 28 | EP — Exposed thermal pad - must be soldered to ground plane |
Ứng dụng tiêu biểu
PIC18LF24K22T-I/ML phù hợp cho 6 Áp dụngs: Battery-Powered IoT Sensor Node, Wearable Health Monitor, Industrial Sensor Conditioning, Low-Power Remote Control, USB-to-UART Bridge, Capacitive Touch User Interface.
Battery-Powered IoT Sensor Node
The PIC18LF24K22T-I/ML is well-suited for battery-powered IoT sensor nodes that transmit periodic telemetry over LoRa, BLE or sub-GHz radios. Its 1.8 V to 3.6 V VDD range allows direct connection to a single CR2032 coin cell or 2x AA alkaline cells without a boost converter, while the nanoWatt XLP sleep current below 50 nA typical (per Microchip datasheet DS39984) extends battery life to multiple years. The 12-bit ADC with 19 channels and the integrated CTMU enable direct interface to resistive, capacitive and analog sensors, while the 64 MHz CPU executes the radio stack and sensor-fusion algorithms in real time. Designers commonly pair this MCU with sub-GHz transceivers such as the Microchip MRF89XA or BLE modules like the RN4870 to build wireless sensor endpoints.
Được đề xuất
Wearable Health Monitor
Wearables for health and fitness monitoring benefit from the PIC18LF24K22T-I/ML's combination of ultra-low-power sleep modes and integrated mTouch capacitive touch sensing. The device can stay in deep sleep with RTCC retention between sensor samples, waking only for sub-millisecond measurement intervals to read optical heart-rate or SpO2 sensors. The 12-bit ADC with computation features (ADC2) provides averaging and threshold detection without CPU intervention, saving additional energy. The 28-QFN (6x6 mm) package footprint fits comfortably inside a wristband form factor while the 1.8 V minimum VDD supports direct operation from small Li-ion or Li-polymer batteries. Designers pair this MCU with optical biosensors such as the MAX30102 to deliver multi-parameter fitness tracking.
Được đề xuất
Industrial Sensor Conditioning
Industrial 4-20 mA loop-powered transmitters and remote sensor conditioning modules often use the PIC18LF24K22T-I/ML for its 12-bit ADC accuracy and low-power operation. The wide operating voltage from 1.8 V to 3.6 V enables direct power from a 3.3 V LDO fed by a loop-derived supply, while the wide industrial temperature range (-40C to +85C) handles factory floor environments. The two EUSART ports support RS-485 or LIN communication, and the dual MSSP ports handle SPI sensors and I2C peripherals concurrently. This makes the part a versatile choice for pressure, temperature and flow sensor transmitters requiring modest computation and low standby current in line-powered or battery-backed installations.
Được đề xuất
Low-Power Remote Control
Battery-powered remote controls for consumer electronics, garage doors and industrial cranes benefit from the PIC18LF24K22T-I/ML's mTouch capacitive sensing, ultra-low sleep current, and IR modulation capability via CCP/ECCP. The MCU can remain in deep sleep until a capacitive touch or button press wakes it, then transmit via PWM-driven IR LED or sub-GHz radio. The 1.8 V minimum supply allows coin-cell operation for years without battery replacement. The 28-QFN package keeps the design compact, while the 16 KB Flash easily accommodates RF stack and user-interface firmware. This is a common architecture for low-cost universal remote controls and wireless key fobs.
Được đề xuất
USB-to-UART Bridge
The PIC18LF24K22T-I/ML implements a USB-to-UART bridge when paired with a USB 2.0 Full-Speed transceiver. The dual EUSART ports support RS-232, RS-485 and LIN interfaces, while the integrated 12-bit ADC and timers provide auxiliary GPIO and PWM for LED status indication. The 64 MHz core delivers ample throughput for UART baud rates up to 1 Mbaud without CPU bottleneck. Its low 1.8 V minimum supply enables bus-powered or self-powered designs with simple LDO regulators. Designers commonly build CDC-ACM virtual COM port bridges using the Microchip USB stack, turning this MCU into a drop-in replacement for commercial bridges.
Được đề xuất
Capacitive Touch User Interface
The PIC18LF24K22T-I/ML integrates Microchip's mTouch capacitive touch sensing module with the CTMU (Charge Time Measurement Unit), enabling up to 25 touch electrodes without external touch ICs. This makes the part ideal for kitchen appliances, automotive interior controls and IoT devices that need sealed-button interfaces. The 12-bit ADC with computation features supports proximity and slider gestures, while the 16 KB Flash easily accommodates touch firmware libraries. The 28-QFN package minimizes PCB area in space-constrained products and the LF variant's 1.8 V minimum supply supports direct battery connection. The hardware CTMU provides noise-robust touch performance even in high-EMI environments.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho PIC18LF24K22T-I/ML — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | PIC18LF24K22-I/ML | PIC18LF23K22T-I/ML | PIC18F24K22-I/ML |
|---|---|---|---|---|
| Package | 28-QFN (6x6 mm) - tape & reel | 28-QFN (6x6 mm) - tray | 28-QFN (6x6 mm) | 28-QFN (6x6 mm) |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Flash Memory | 16 KB | 16 KB | 8 KB | 16 KB |
| SRAM | 768 bytes | 768 bytes | 768 bytes | 768 bytes |
| EEPROM | 256 bytes | 256 bytes | 256 bytes | 256 bytes |
| Max Frequency | 64 MHz (16 MIPS) | 64 MHz (16 MIPS) | 64 MHz (16 MIPS) | 64 MHz (16 MIPS) |
| VDD Range | 1.8 V to 3.6 V | 1.8 V to 3.6 V | 1.8 V to 3.6 V | 2.4 V to 5.5 V |
| Operating Temperature | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C |
Bảo phân biệt quan trọng
- Lowest VDD floor in the K22 family (vsPIC18F24K22-I/ML)
- 16 KB Flash tier vs lower-density siblings (vsPIC18LF23K22T-I/ML)
- Tape & reel packaging for high-volume assembly (vsPIC18LF24K22-I/ML)
Ghi chú thiết kế
The 28-QFN (ML) package has an exposed thermal pad (EP, pin 28) that MUST be soldered to the PCB ground plane for proper thermal dissipation, mechanical reliability and electrical ground reference. According to Microchip datasheet DS39984, omitting the EP solder connection can cause thermal runaway, EMI issues and unreliable operation. Use sufficient micro-via stitching (typically 9-12 vias) under the EP for optimal thermal performance.
Estimated: at VDD=3.3 V, CPU=64 MHz, IO load=10 mA, total active current is approximately 8 mA. To extend battery life, use Sleep mode (under 50 nA typical per datasheet DS39984) and only enable peripherals on demand. For applications averaging <1% duty cycle, average current can fall below 100 uA, extending a CR2032 coin cell life beyond five years.
Place a 100 nF decoupling capacitor as close as possible to the VDD pin (pin 11) with a short trace. Add a 10 uF tantalum or electrolytic bulk capacitor on the VSS plane near the MCU. For ADC accuracy, isolate analog VDD from digital VDD with a ferrite bead and add a dedicated 100 nF cap to the AVVDD pin (not present on 28-QFN, use filtered digital VDD).
Thông tin tuân thủ
Industrial temperature grade only (-40C to +85C). AEC-Q100 automotive variants are not available in this MPN family - choose PIC18F K22 Q1 suffixes for automotive.
