PIC18LF47J13T-I/ML - 128KB Flash 8-bit XLP MCU 44-QFN | Microchip
MPN: PIC18LF47J13T-I/ML ✓ Hoạt độngPIC18LF47J13T-I/ML Tóm tắt
An 8-bit microcontroller (MCU) is a small programmable processor that integrates CPU, Flash, RAM, and peripherals on a single silicon die; the PIC18 family is Microchip's high-performance 8-bit architecture using a 16-bit instruction word with RISC-style pipelining, sitting in the hierarchy MCU -> microcontroller -> embedded processor -> semiconductor. The LF prefix denotes the wide-voltage 2.0V-3.6V variant optimized for battery-powered XLP designs.
Key features include 128 KB Flash (64K x 16), 4 KB RAM, 12-bit ADC with multiple channels, deep sleep current under 100 nA typical, internal oscillator, nanoWatt XLP technology, and integrated peripherals including comparators, PWM, I2C/SPI/UART, and CTMU for touch applications. The 34 I/O count enables rich peripheral integration in space-constrained designs.
Architecturally the device uses a 16-bit modified Harvard bus with a C compiler-friendly instruction set, deep sleep and ultra-low-power Run modes, hardware RTCC, and on-chip voltage regulator operating from 2.0V-3.6V, supporting either USB 2.0 full-speed via the internal transceiver or low-energy Bluetooth stacks. The 8x8 mm QFN package provides thermal dissipation for higher-speed operation.
Typical applications include low-power wireless sensor nodes, USB peripherals, consumer electronics, battery-powered medical devices, industrial control panels, and IoT edge nodes where deep sleep current directly determines battery life.
When designing with this part, plan pin allocation to share the 44-pin QFN between the USB D+/D- pair, the ICSP programming pins (PGED/PGEC), and your application I/O; an external 8 MHz crystal plus PLL can drive the 48 MHz system clock, or the internal 31 kHz-8 MHz RC oscillator can eliminate external clock hardware.
Bộ thay thế dễ dàng lắp đặt cho PIC18LF47J13T-I/ML — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với PIC18LF47J13T-I/ML (cùng hình factor và footprint) — khác nhau ở Package, ADC, Operating Temperature, I/O Pins, Core.
PIC18LF47J13-I/ML
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
PIC18F47J13-I/ML
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →PIC18F47J53-I/ML
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC18F46J50-I/ML
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
PIC18LF46J13-I/ML
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →PIC18F4553-I/ML
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC18LF47J13T-I/ML Tỷ lệ tối đa & tính chất điện
| Family | PIC18 XLP 18J |
| Core | 8-bit PIC |
| Program Memory | 128 KB Flash (64K x 16) |
| RAM Size | 4 KB (3.8K x 8) |
| Maximum CPU Speed | 48 MHz (12 MIPS) |
| Điện áp cung cấp | 2.0 V to 3.6 V |
| I/O Pins | 34 |
| ADC | 12-bit, multi-channel |
| Hộp | 44-pin VQFN (8x8 mm) exposed pad |
| Kiểu lắp đặt | Surface Mount |
| Nhiệt độ hoạt động | -40C to +85C (Industrial) |
| Oscillator | Internal + external crystal support |
| USB | USB 2.0 Full-Speed (on select variants) |
| Trạng thái RoHS | Compliant |
| Cấp MSL | 3 (168 hours) |
Hướng dẫn cấu hình chân PIC18LF47J13T-I/ML 44-pin vqfn (8x8 mm) exposed pad
Cấu hình chân cho PIC18LF47J13T-I/ML (44-pin vqfn (8x8 mm) exposed pad gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho PIC18LF47J13T-I/ML.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
PIC18LF47J13T-I/ML phù hợp cho 6 Áp dụngs: Battery-Powered Wireless Sensor Node, USB HID Peripheral Device, Industrial Control Panel HMI, Portable Medical Monitoring Device, Consumer Electronics Remote Control, IoT Edge Sensor with BLE Connectivity.
Battery-Powered Wireless Sensor Node
The PIC18LF47J13T-I/ML fits battery-powered wireless sensor nodes through its nanoWatt XLP technology with deep-sleep current under 100 nA typical and 128 KB Flash capable of holding Zigbee, BLE stack, or proprietary RF protocol firmware. Its 2.0V-3.6V supply range supports direct connection to single-cell Li-ion (3.0V nominal) or two AA cells without external regulation. The 12-bit ADC with multiple channels directly interfaces temperature, humidity, and battery-voltage sensors, while 34 I/O pins connect to user buttons, LEDs, and an SPI-connected radio module. Compared to higher-power MCUs, this part extends coin-cell battery life from months to years in duty-cycled sensor applications.
Được đề xuất
USB HID Peripheral Device
The PIC18LF47J13T-I/ML is well-suited to USB Human Interface Device applications such as keyboards, mice, game controllers, and custom HID peripherals through its integrated USB 2.0 Full-Speed peripheral with on-chip transceiver. The 128 KB Flash comfortably stores USB HID class drivers plus application firmware, and the 48 MHz core delivers 12 MIPS to handle USB polling at 1 kHz without CPU saturation. Designers connect D+/D- directly to the USB connector with a 1.5 kohm pull-up on D+ for full-speed device enumeration. The exposed thermal pad on the 44-QFN package dissipates heat during sustained USB traffic and bus-powered operation.
Được đề xuất
Industrial Control Panel HMI
The PIC18LF47J13T-I/ML supports industrial HMI panels with -40C to +85C industrial temperature range, 128 KB Flash for menu structures and I/O handling code, and 34 I/O to drive character LCDs, scan keypads, and interface opto-isolated inputs. The wide 2.0V-3.6V supply tolerates industrial 24V bus systems regulated down via a simple buck converter. The 12-bit ADC handles analog sensor inputs such as 4-20 mA current loop receivers and thermistor networks. Compared to smaller Flash MCUs, the J13 reserves code space for IEC 61131-3 style ladder logic interpreters or Modbus RTU protocol stacks.
Được đề xuất
Portable Medical Monitoring Device
The PIC18LF47J13T-I/ML suits portable medical devices such as pulse oximeters, blood pressure monitors, and continuous glucose monitors through its XLP deep-sleep modes that extend battery life to multi-year operation on a single coin cell. The 12-bit ADC with multiple channels samples photodiode signals (pulse oximetry) or impedance measurements accurately, while 128 KB Flash stores FDA-traceable firmware plus wireless protocol stacks for transmitting vitals to a paired phone. The 2.0V-3.6V supply accepts single Li-ion or 3V coin cells without external regulation. Compared to higher-performance ARM Cortex MCUs, the PIC18LF47J13 provides simpler IEC 62304 software classification pathways.
Được đề xuất
Consumer Electronics Remote Control
The PIC18LF47J13T-I/ML is ideal for advanced consumer remote controls with voice activation, IR/RF transmission, and OLED display drivers through its 128 KB Flash accommodating voice recognition libraries and protocol stacks for IR (RC5/RC6/SIRC) or 2.4 GHz RF transmission. The deep-sleep current under 100 nA typical preserves battery life when the remote sits idle, waking only on button press or motion interrupt. The 12-bit ADC reads battery voltage and ambient light sensors for adaptive backlight control, while 34 I/O drives a 7-row by 8-column keypad matrix and OLED display SPI interface. Compared to 32-bit MCUs, the J13 offers lower BOM cost in this cost-sensitive consumer category.
Được đề xuất
IoT Edge Sensor with BLE Connectivity
The PIC18LF47J13T-I/ML fits IoT edge sensor designs with external BLE modules through its 128 KB Flash storing sensor fusion algorithms, BLE command parsers, and OTA bootloader code. The 48 MHz core executes sensor sampling and BLE event handling without bottlenecks, and the 4 KB RAM accommodates small data buffers for environmental, motion, or proximity sensor data streams. The 2.0V-3.6V supply supports direct Li-ion or regulated 3.3V USB power, while the 12-bit ADC handles analog front-end signals from gas sensors, thermistors, or strain gauges. Compared to integrated BLE SoCs, this approach allows module swap flexibility across BLE, LoRa, or sub-GHz protocols.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho PIC18LF47J13T-I/ML — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | PIC18LF47J13-I/ML | PIC18F47J13-I/ML | PIC18F47J53-I/ML | PIC18F46J50-I/ML | PIC18LF46J13-I/ML |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 44-pin VQFN (8x8 mm) | 44-pin VQFN (8x8 mm) - same | 44-pin VQFN (8x8 mm) - same | 44-pin VQFN (8x8 mm) - same | 44-pin VQFN (8x8 mm) - same | 44-pin VQFN (8x8 mm) - same |
| Program Flash | 128 KB | 128 KB | 128 KB | 64 KB | 64 KB | 64 KB |
| RAM | 4 KB | 4 KB | 4 KB | 3.8 KB | 3.9 KB | 3.8 KB |
| Supply Voltage | 2.0V to 3.6V | 2.0V to 3.6V | 2.0V to 3.6V (3.0V min for some features) | 2.0V to 3.6V | 2.0V to 3.6V | 2.0V to 3.6V |
| XLP / Deep Sleep | Yes (nanoWatt XLP) | Yes (nanoWatt XLP) | Yes (nanoWatt) | Yes (nanoWatt) | Yes (nanoWatt) | Yes (nanoWatt XLP) |
| USB | USB 2.0 Full-Speed Device | USB 2.0 Full-Speed Device | USB 2.0 Full-Speed Device | USB 2.0 OTG (Host + Device) | USB 2.0 Full-Speed Device | USB 2.0 Full-Speed Device |
| Pin Count / I/O | 44-pin / 34 I/O | 44-pin / 34 I/O | 44-pin / 34 I/O | 44-pin / 34 I/O | 44-pin / 34 I/O | 44-pin / 34 I/O |
Bảo phân biệt quan trọng
- Largest Flash in the 44-QFN LF XLP family (vsPIC18LF46J13-I/ML)
- Integrated USB 2.0 Full-Speed with on-chip transceiver (vsPIC18F4553-I/ML)
- LF low-voltage process for true XLP operation (vsPIC18F47J13-I/ML)
Ghi chú thiết kế
Estimated: At VDD = 3.3V, 48 MHz active, the PIC18LF47J13T-I/ML draws approximately 15-20 mA active current. For battery operation, switching the CPU to deep sleep between samples reduces current below 100 nA typical. Use the internal 31 kHz RTCC for sleep-mode timing, waking the CPU only on RTCC rollover or external interrupt to achieve multi-year battery life on a 220 mAh coin cell.
The 44-pin QFN package has an exposed thermal pad on the bottom that MUST be soldered to a continuous ground pour on the PCB for both thermal dissipation and electrical reference. Place four or more thermal vias in the exposed pad land pattern connecting top copper to internal ground planes. The QFN ground pad is pin 45 (the die substrate), so a missing solder connection here causes erratic ADC readings and USB communication failures.
The PIC18LF47J13T-I/ML requires a 10 uF bulk capacitor plus a 0.1 uF ceramic decoupling capacitor placed within 5 mm of the VDD pin. The PGED1/PGEC1 pins are shared with general I/O and must be accessible for ICSP programming - do not place them on nets that conflict with debugging access. The USB D+/D- traces must be 90 ohm differential and length-matched within 2 mm; otherwise enumeration failures occur at full-speed USB. The configuration words must be programmed correctly or the part will operate in an unexpected oscillator mode.
Estimated: The 44-pin VQFN (8x8 mm) package has theta_JA of approximately 30 C/W with a properly soldered ground pad and 1 oz copper. At 3.3V x 20 mA active, dissipation is 66 mW, resulting in a 2 C junction temperature rise - well within the 125 C maximum. In industrial -40C to +85C environments, ensure the PCB ground pour provides adequate heat spreading for sustained USB or RF transmission bursts that draw higher transient currents.
Thông tin tuân thủ
RoHS and REACH compliant per Microchip product page; lead-free packaging confirmed. Not AEC-Q100 qualified - this part targets consumer, industrial, and IoT applications rather than automotive. Halogen-free status not explicitly stated in verified data.
