PIC24F08KL402T-I/SS - 16-Bit 8KB Flash MCU | Microchip
MPN: PIC24F08KL402T-I/SS ✓ Hoạt độngPIC24F08KL402T-I/SS Tóm tắt
A PIC24F microcontroller belongs to the 16-bit MCU hierarchy and provides a practical balance between processing performance, peripheral integration, memory capacity, and power efficiency. The PIC24F08KL402 family is positioned for compact control systems that require more arithmetic capability than an 8-bit MCU while retaining a relatively simple architecture, low-power operating modes, and a broad selection of serial and timing peripherals.
Key features include 8 KB of Flash memory organized as 2.75K × 24 words, 1 KB of RAM, 512 bytes of EEPROM, and an ADC with 12 channels and 10-bit resolution. The MCU also provides I2C and SPI through its MSSP peripheral, two 16-bit timer/counter blocks, up to two 8-bit timers, and two CCP modules for capture, compare, or PWM operation. Configurable open-drain digital outputs add flexibility for bus and signal interfaces.
The 32 MHz core delivers a maximum instruction rate of 16 MIPS, making the PIC24F08KL402T-I/SS suitable for responsive control loops and peripheral-heavy embedded products. Its nanoWatt XLP architecture supports low-power operation, which is valuable in battery-powered equipment, portable instruments, and systems that spend substantial time in sleep or idle states. The 10-bit ADC supports analog measurement while configurable digital outputs and serial interfaces expand system-level connectivity.
Typical applications include industrial sensor controllers, compact power-supply monitors, building-control modules, battery-powered instruments, serial data loggers, and low-cost embedded control boards. The combination of EEPROM, Flash, ADC, UART-like serial connectivity, timers, and PWM allows a compact design to perform measurement, control, configuration storage, and communications without requiring a separate external memory device.
PCB implementation should preserve short, clean return paths for analog and digital signals and provide suitable decoupling close to the supply pins. Because the SSOP footprint has closely spaced leads, inspect the manufacturer pin-description table before assigning tracks, programming connector signals, or checking exposed pad requirements. Validate the final component orientation and pin numbering against the package drawing before fabrication.
This product page combines the manufacturer product information, verified distributor specifications, application guidance, lifecycle considerations, and design-oriented comparison content. It is intended to help engineers identify the correct 28-pin PIC24F configuration and plan low-power, mixed-signal embedded designs without treating a similar package number as a guaranteed replacement.
Bộ thay thế dễ dàng lắp đặt cho PIC24F08KL402T-I/SS — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với PIC24F08KL402T-I/SS (cùng hình factor và footprint).
Không có bộ thay thế dễ dàng lắp đặt sẵn có cho sản phẩm này.
Yêu cầu các bộ thay thếPIC24F08KL402T-I/SS Tỷ lệ tối đa & tính chất điện
| Architecture | 16-bit |
| Maximum CPU Frequency | 32 MHz |
| Instruction Throughput | 16 MIPS |
| Flash Memory | 8 KB (2.75K × 24 words) |
| RAM | 1 KB |
| EEPROM | 512 bytes |
| ADC Resolution | 10 bits |
| ADC Channels | 12 channels |
| Digital I/O Sink Current | 18 mA per pin |
| Digital I/O Source Current | 18 mA per pin |
| Open-Drain Outputs | Configurable on digital I/O pins |
| External Interrupt Sources | Up to 3 sources |
| 16-Bit Timer/Counters | 2 |
| 8-Bit Timer/Counters | Up to 2 |
| Capture/Compare/PWM Modules | 2 CCP modules |
| Serial Peripheral | MSSP supporting I2C and SPI |
| Điện áp cung cấp | 3 V |
| Power Technology | nanoWatt XLP |
| Hộp | 28-pin SSOP |
Hướng dẫn cấu hình chân PIC24F08KL402T-I/SS 28-pin ssop
Cấu hình chân cho PIC24F08KL402T-I/SS (28-pin ssop gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho PIC24F08KL402T-I/SS.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
PIC24F08KL402T-I/SS phù hợp cho 6 Áp dụngs: Industrial Sensor Controller, Low-Power Data Logger, Power-Supply Monitor, Serial Communications Module, Building Control and Automation, LED and PWM Control.
Industrial Sensor Controller
The PIC24F08KL402T-I/SS fits compact industrial sensor nodes that combine analog measurement with low-power digital control. Its 12-channel, 10-bit ADC can monitor multiple sensor inputs, while the two 16-bit timer/counters support precise timing tasks and the CCP modules can generate PWM outputs. The 16-bit core operating at up to 32 MHz and 16 MIPS provides responsive signal processing without moving to a higher-power processor. EEPROM can retain calibration or configuration values across power cycles. Place the MCU near the sensor interface, route analog inputs away from switching nodes, and use the MSSP in I2C or SPI mode when the remote sensor requires a serial interface.
Được đề xuất
Low-Power Data Logger
The PIC24F08KL402T-I/SS is suitable for portable data-logging equipment that must balance storage, measurement, and standby power. Its 8 KB of Flash holds firmware and configuration data, while 1 KB of RAM supports working buffers and the 512-byte EEPROM preserves device identity or calibration information. The 10-bit ADC can sample sensors at a controlled interval, and the nanoWart XLP architecture supports low-power operating modes for long battery life. A practical design can wake with a timer, acquire measurements, store results in Flash or EEPROM, and return to sleep. Select external storage only when the application requires more than the MCU's internal memory.
Được đề xuất
Power-Supply Monitor
The PIC24F08KL402T-I/SS can supervise a compact power module by using its 10-bit ADC to monitor analog feedback and its digital I/O to inspect operating-state signals. Two CCP modules can support power-control or dimming functions, while the timer/counter blocks provide accurate delays and periodic measurement timing. The 32 MHz, 16-bit processing core is sufficient for supervisory logic, fault recording, and communication with a higher-level controller. EEPROM is useful for storing thresholds or event counters. The analog input network must respect the electrical limits in the manufacturer datasheet, and power rails should be sequenced only after checking which pins remain operational during reset.
Được đề xuất
Serial Communications Module
The PIC24F08KL402T-I/SS works for compact protocol-conversion and embedded communications equipment because its MSSP peripheral supports I2C and SPI while general-purpose digital I/O supports additional serial functions. At 32 MHz with 16 MIPS throughput, the MCU can frame packets, service timers, update indicators, and maintain protocol timing concurrently. Its 8 KB of Flash supports a moderate protocol stack or command table, and EEPROM can retain configuration parameters such as addresses or baud-rate settings. For a new PCB, route the serial interface away from ADC and PWM signals, provide stable clocking, and verify pin multiplexing in the exact 28-pin device documentation.
Được đề xuất
Building Control and Automation
The PIC24F08KL402T-I/SS is appropriate for distributed building-control nodes that monitor inputs and control limited loads. The 12-channel ADC can read potentiometers, temperature sensors, and other analog transducers, while timer/counter and CCP peripherals handle periodic sampling and actuator timing. Configurable open-drain outputs can support communication buses or wired sensor interfaces where appropriate. EEPROM preserves room-specific configuration, and the compact 28-pin SSOP package helps limit board area. Keep mains-derived or high-energy interfaces outside the MCU's electrical limits, use isolation where required, and design watchdog and reset behavior around the application's fail-safe requirements.
Được đề xuất
LED and PWM Control
The PIC24F08KL402T-I/SS can drive dimming, indicator, or status-control circuitry using the resources of its two CCP modules. PWM generation, timing, and status updates can be handled by the 16-bit core while the MSSP communicates with a display or remote controller. The 32 MHz operating speed provides timing headroom for multiple control functions, and the 10-bit ADC can monitor a current-sense or potentiometer input for feedback control. Low-current LEDs may be connected through suitable driver transistors or buffers after checking the individual pin limits. High-current lighting should use a dedicated driver, while the MCU supplies control, timing, and fault-status information.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho PIC24F08KL402T-I/SS — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này |
|---|---|
| Package | 28-pin SSOP |
| Brand | Microchip Technology |
| CPU Architecture | 16-bit |
| Maximum CPU Frequency | 32 MHz |
| Instruction Throughput | 16 MIPS |
| Flash Memory | 8 KB |
| RAM | 1 KB |
| EEPROM | 512 bytes |
| ADC | 12-channel, 10-bit |
| Low-Power Technology | nanoWart XLP |
Bảo phân biệt quan trọng
- Integrated mixed-signal capability (vsPIC24F08KL402-I/SS)
- Instruction throughput for embedded control (vsPIC24F08KL402-I/SS)
- Low-power system integration (vsPIC24F08KL402T-I/SO)
Ghi chú thiết kế
Use the manufacturer package drawing and pin-description table to assign every connection before routing the 28-pin SSOP footprint. Pay particular attention to programming, reset, analog-reference, and multiplexed peripheral signals because their functions cannot be inferred from generic 28-pin MCU conventions. Keep the footprint and component orientation consistent with the assembly drawing, and verify pin 1 against the package marker before fabrication.
Route analog inputs away from PWM outputs, high-current switching nodes, and long digital traces. Place input filtering or sensing components close to the relevant pins, follow the datasheet recommendations for analog grounding, and keep the 10-bit ADC reference and supply connections stable. If the MCU also drives PWM-controlled loads, increase separation between analog and power paths and evaluate the finished board for switching-induced measurement error.
Design the 3 V supply path for both normal operation and the highest expected peripheral load. Apply the manufacturer recommendations for decoupling and place the required capacitors close to the appropriate supply and ground pins. For battery-powered designs, calculate the average current from active and sleep durations, then verify the external regulator's quiescent current; the MCU's low-power capability cannot compensate for excess current in the rest of the power path.
Do not treat a similar 28-pin ordering code as an automatic substitute. Validate the exact pin assignments, peripheral availability, memory organization, electrical limits, temperature grade, and package drawing before changing the MPN. In particular, review MSSP pin mapping, ADC inputs, CCP outputs, and programming pins on the schematic. A board-level substitution requires both footprint compatibility and functional equivalence across every connected signal.
Thông tin tuân thủ
The target is a general-purpose industrial-temperature-ordering-code microcontroller rather than an AEC-Q100 automotive-qualified variant. Explicit RoHS, REACH, lead-free, halogen-free, and conflict-minerals statements were not established.