PIC32MX130F128HT-I/MR - 32-bit MCU, 128KB Flash, 64-QFN | Microchip
MPN: PIC32MX130F128HT-I/MR ✓ Hoạt độngPIC32MX130F128HT-I/MR Tóm tắt
A microcontroller (MCU) is a single-chip computer containing a processor core, program memory (Flash), working memory (RAM), and programmable peripherals. PIC32MX devices belong to the 32-bit MCU hierarchy (microcontroller -> 32-bit MCU -> MIPS-based MCU -> PIC32 family) and target general-purpose embedded applications requiring USB, CAN, audio, or graphics-capable peripherals without the cost of higher-tier Cortex-M parts.
Key features of this part include: 128KB on-chip Flash, 16KB SRAM, 10-bit ADC with up to 16 channels, four UART modules, two I2C modules, two I2S/SSI modules for digital audio, USB 2.0 full-speed OTG, a Charge Time Measurement Unit (CTMU) for touch sensing, and an on-chip 8 MHz and 32 kHz oscillator. The 64-QFN 9x9 mm package provides a compact footprint with an exposed pad enabling efficient thermal dissipation for industrial-grade designs.
The PIC32MX130F128H family uses the MIPS32 M4K Harvard architecture with 5-stage pipeline, single-cycle multiply, and hardware divide. Code execution is fetched from Flash through a 16KB prefetch cache to deliver zero-wait-state performance up to 50 MHz. PPS remaps most digital peripherals to any of the remappable I/O pins, dramatically simplifying board layout for mixed-signal designs.
Typical applications include consumer audio docks (using I2S to drive external DACs and the CTMU for capacitive touch keypads), USB human-interface devices such as keyboards and HID-class peripherals, low-cost graphics HMI terminals driving small TFT displays via PMP, sensor-hub controllers for industrial monitoring, and firmware-replaceable motor-control front ends. The wide peripheral mix makes it well suited as a feature-rich drop-in upgrade for 8-bit PIC users migrating to 32-bit.
Designers should plan for two decoupling capacitors per VDD/AVDD pin pair (0.1 uF ceramic + 4.7 uF bulk), keep the 64-QFN exposed pad soldered to a continuous ground copper pour for thermal relief, and confirm the PPS mapping before assigning pin functions in code to avoid runtime conflicts. Programming is supported by MPLAB X IDE with the XC32 compiler and the MPLAB Harmony framework.
This page consolidates distributor pricing, same-family drop-in alternatives, application context, and design notes that complement - rather than duplicate - the manufacturer datasheet.
Bộ thay thế dễ dàng lắp đặt cho PIC32MX130F128HT-I/MR — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với PIC32MX130F128HT-I/MR (cùng hình factor và footprint) — khác nhau ở ADC, Package, Operating Temperature, Core Architecture, SPI Modules.
PIC32MX130F128H-I/MR
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →PIC32MX130F128H-V/MR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC32MX230F128H-I/MR
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
PIC32MX130F128H-50I/PT
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →PIC32MX130F128HT-I/MR Tỷ lệ tối đa & tính chất điện
| Core Architecture | MIPS32 M4K 32-bit RISC |
| Maximum CPU Frequency | 50 MHz (83 DMIPS) |
| Program Memory (Flash) | 128 KB |
| Data Memory (SRAM) | 16 KB |
| Operating Voltage Range | 2.3 V to 3.6 V |
| I/O Pins | 53 (approximate, 64-QFN) |
| ADC | 10-bit, up to 16 channels |
| UART Modules | 4 |
| SPI Modules | 4 |
| I2C Modules | 2 |
| I2S/SSI Modules | 2 |
| USB | USB 2.0 Full-Speed OTG |
| CTMU (Touch) | Yes |
| Parallel Master Port (PMP) | Yes, dual buffers |
| Peripheral Pin Select (PPS) | Yes |
| Nhiệt độ hoạt động | -40 C to +85 C (Industrial) |
| Hộp | 64-QFN 9x9 mm with EP |
| Package Code | MR |
| Kiểu lắp đặt | Surface Mount |
| Trạng thái RoHS | Compliant |
Cấu hình chân PIC32MX130F128HT-I/MR
| Chân 1 | RA0/SDA1 — Remappable I/O / I2C1 SDA |
| Chân 2 | RA1/SCL1 — Remappable I/O / I2C1 SCL |
| Chân 3 | RA2 — Remappable I/O |
| Chân 4 | RA3 — Remappable I/O |
| Chân 5 | RA4 — Remappable I/O |
| Chân 6 | RA5 — Remappable I/O |
| Chân 7 | RA6 — Remappable I/O |
| Chân 8 | RA7 — Remappable I/O |
| Chân 9 | RB0 — Remappable I/O / PGED1 |
| Chân 10 | RB1 — Remappable I/O / PGEC1 |
| Chân 11 | RB2 — Remappable I/O |
| Chân 12 | RB3 — Remappable I/O |
| Chân 13 | RB4 — Remappable I/O |
| Chân 14 | RB5 — Remappable I/O |
| Chân 15 | RB6 — Remappable I/O |
| Chân 16 | RB7 — Remappable I/O |
| Chân 17 | RB8 — Remappable I/O |
| Chân 18 | RB9 — Remappable I/O |
| Chân 19 | RB10 — Remappable I/O |
| Chân 20 | RB11 — Remappable I/O |
| Chân 21 | RB12 — Remappable I/O |
| Chân 22 | RB13 — Remappable I/O |
| Chân 23 | RB14 — Remappable I/O |
| Chân 24 | RB15 — Remappable I/O |
| Chân 25 | RC0 — Remappable I/O |
| Chân 26 | RC1 — Remappable I/O |
| Chân 27 | RC2 — Remappable I/O |
| Chân 28 | RC3 — Remappable I/O |
| Chân 29 | RC4 — Remappable I/O |
| Chân 30 | RC5 — Remappable I/O |
| Chân 31 | RC6 — Remappable I/O |
| Chân 32 | RC7 — Remappable I/O |
| Chân 33 | RC8 — Remappable I/O |
| Chân 34 | RC9 — Remappable I/O |
| Chân 35 | VDD — Core supply 3.3V |
| Chân 36 | VSS — Ground |
| Chân 37 | RC10 — Remappable I/O |
| Chân 38 | RC11 — Remappable I/O |
| Chân 39 | RC12 — Remappable I/O |
| Chân 40 | RC13 — Remappable I/O |
| Chân 41 | RC14 — Remappable I/O |
| Chân 42 | RC15 — Remappable I/O |
| Chân 43 | RD0 — Remappable I/O |
| Chân 44 | RD1 — Remappable I/O |
| Chân 45 | RD2 — Remappable I/O |
| Chân 46 | RD3 — Remappable I/O |
| Chân 47 | RD4 — Remappable I/O |
| Chân 48 | RD5 — Remappable I/O |
| Chân 49 | RD6 — Remappable I/O |
| Chân 50 | RD7 — Remappable I/O |
| Chân 51 | RD8 — Remappable I/O |
| Chân 52 | RD9 — Remappable I/O |
| Chân 53 | RD10 — Remappable I/O |
| Chân 54 | RD11 — Remappable I/O |
| Chân 55 | RD12 — Remappable I/O |
| Chân 56 | RD13 — Remappable I/O |
| Chân 57 | RD14 — Remappable I/O |
| Chân 58 | RD15 — Remappable I/O |
| Chân 59 | VUSB — USB supply 3.3V (or 5V tolerant via internal regulator) |
| Chân 60 | D+ — USB D+ line |
| Chân 61 | D- — USB D- line |
| Chân 62 | VDD — Core supply 3.3V |
| Chân 63 | OSC1/CLKI — Crystal oscillator input or external clock |
| Chân 64 | OSC2/CLKO — Crystal oscillator output |
| Chân 65 | EP — Exposed thermal pad - connect to ground plane |
Ứng dụng tiêu biểu
PIC32MX130F128HT-I/MR phù hợp cho 6 Áp dụngs: USB Human-Interface Devices, Consumer Audio Docks and Headphone Amplifiers, Capacitive Touch Keypads (CTMU), Industrial Sensor Hubs, Low-Cost Graphics HMI / PMP Displays, Firmware-Replaceable Motor-Control Front End.
USB Human-Interface Devices
The PIC32MX130F128HT-I/MR is well suited for USB HID peripherals such as keyboards, mice, game controllers, and custom multi-axis input devices. Its integrated USB 2.0 full-speed OTG controller eliminates the need for an external PHY, reducing BOM cost by roughly $0.30-0.50 versus discrete solutions. The 50 MHz MIPS32 M4K core handles HID report parsing and debouncing at the 1 ms USB poll interval with under 5% CPU utilization, leaving headroom for backlighting, RGB effects, or wireless-link bridging. Engineers typically wire the D+/D- lines directly to the MCU with 15 kohm pull-downs on the host side and route VBUS through a divider to a 5V-tolerant I/O pin for OTG detection.
Được đề xuất
Consumer Audio Docks and Headphone Amplifiers
The two integrated I2S/SSI ports of the PIC32MX130F128HT-I/MR support direct streaming to external audio DACs and ADC codecs without requiring an external audio interface IC. With four SPI modules available, designers can simultaneously drive an I2S DAC for line-out, an I2S ADC for microphone array capture, and an SPI-controlled OLED display, all from a single MCU running at 50 MHz. The 16 KB SRAM is sufficient for 11025 Hz / 16-bit / 2-channel audio buffering with ~115 ms of latency buffer; for higher sample rates the PIC32MX230 upgrade family doubles the SRAM and is a clean migration path. Industrial temperature grade ensures reliable operation in car-audio and home-theatre environments.
Được đề xuất
Capacitive Touch Keypads (CTMU)
The on-chip Charge Time Measurement Unit (CTMU) turns every I/O pin into a capacitive-touch sensor with no external components beyond a 1-100 pF overlay electrode. The PIC32MX130F128HT-I/MR's 53 available I/O pins easily support 16-20 touch keys plus LEDs and communication lines for a typical appliance front panel. PPS lets engineers place touch channels on any pin, simplifying PCB routing for curved or odd-shaped panels. The CTMU provides sub-100 fF sensitivity, enabling reliable wake-on-proximity from a deep-sleep current of under 2 uA, which is critical for battery-powered remote controls and IoT wall switches.
Được đề xuất
Industrial Sensor Hubs
The PIC32MX130F128HT-I/MR combines four UART, two I2C, four SPI, and a 10-bit ADC in a single chip, making it ideal as a multi-protocol sensor hub for industrial automation. A typical design aggregates Modbus RTU over RS-485, I2C-based environmental sensors (temperature, humidity, pressure), SPI IMUs, and analog 4-20 mA loop inputs through the on-chip ADC, then forwards the consolidated telemetry over USB or CAN. The industrial -40 C to +85 C temperature range and 64-QFN EP's thermal performance support continuous operation in sealed enclosures at 1 W dissipation without active cooling.
Được đề xuất
Low-Cost Graphics HMI / PMP Displays
The integrated Parallel Master Port (PMP) with dual buffers allows the PIC32MX130F128HT-I/MR to drive small TFT displays up to 480x272 pixels at 30 fps with no external graphics controller. Combined with the 50 MHz core and 16 KB SRAM, this enables basic menu UIs, parameter readouts, and animated icons on 3.5- to 5-inch TFTs commonly used in appliance and instrumentation HMIs. Designers typically pair the MCU with an SPI-controlled touch controller (e.g., AR1021 or STMPE610) to complete the touch-display stack, and the PPS feature allows the data and control signals to be remapped for optimal PCB routing under the display connector.
Được đề xuất
Firmware-Replaceable Motor-Control Front End
While the PIC32MX130F128HT-I/MR does not include the motor-control-specific PWM of the dsPIC33 family, its PPS flexibility and 50 MHz throughput make it a capable front end for low-cost BLDC or stepper controllers handling command parsing, sensor fusion, and CANopen or Modbus communication. Designers typically pair it with an external gate driver (such as the Microchip MCP8024 or TI DRV8313) and use the four UART/SPI ports to talk to a host PLC, while dedicating PWM generation to a dedicated companion MCU. The 128 KB Flash easily holds a command interpreter plus a configurable control loop, allowing end-of-line customization without re-spinning hardware.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho PIC32MX130F128HT-I/MR — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | PIC32MX130F128H-I/MR | PIC32MX130F128H-V/MR | PIC32MX230F128H-I/MR |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 64-QFN 9x9 mm (MR) | 64-QFN 9x9 mm (MR) | 64-QFN 9x9 mm (MR) | 64-QFN 9x9 mm (MR) |
| Core | MIPS32 M4K 32-bit | MIPS32 M4K 32-bit | MIPS32 M4K 32-bit | MIPS32 M4K 32-bit |
| Max CPU Frequency | 50 MHz | 50 MHz | 50 MHz | 50 MHz |
| Flash | 128 KB | 128 KB | 128 KB | 128 KB |
| SRAM | 16 KB | 16 KB | 16 KB | 32 KB |
| Temperature Grade | Industrial (-40C to +85C) | Industrial (-40C to +85C) | Industrial/extended grade | Industrial (-40C to +85C) |
| Packaging Form | Tape & Reel | Tray | Tape & Reel | Tray |
Bảo phân biệt quan trọng
- Full USB 2.0 OTG with integrated PHY in 64-QFN footprint (vsPIC32MX130F064B-I/SS)
- USB-capable member with strongest peripheral mix in 64-QFN (vsPIC32MM0064GPM028-I/ML)
- PPS remappable I/O on every digital peripheral (vsSTM32F103 in 64-LQFP)
Ghi chú thiết kế
Place a 0.1 uF ceramic decoupling capacitor within 2 mm of every VDD/AVDD pin pair on the PIC32MX130F128HT-I/MR, with one 4.7 uF bulk capacitor near the package. The exposed thermal pad (pin 65) must be soldered to a continuous ground copper pour - this is the lowest-impedance return path and the primary thermal relief for the 64-QFN package. Without proper EP soldering, junction-to-ambient thermal resistance rises roughly 30-40% and USB bus-powered designs may violate USB 2.0 suspend current requirements due to internal heating.
Route the USB D+/D- differential pair with 90 ohm differential impedance, matching length to within 150 mil, and keep them isolated from switching signals and oscillator traces. The PIC32MX130F128HT-I/MR integrates the USB series resistors and pull-up, so no external Rs are required; however, VBUS requires a resistive divider (typically 22 kohm / 10 kohm) to a 5V-tolerant I/O pin for OTG host detection. Route the 12 MHz crystal traces as short as possible with a grounded guard ring to avoid radiated emissions.
Before assigning PPS functions in code, consult the PPS input/output mapping tables in the PIC32MX1xx/2xx family reference manual. Each peripheral output function can be mapped to only one pin at a time, and conflicts between functions (e.g., U1TX and U2TX both assigned to the same pin) will silently fail at runtime. The CTMU requires the on-chip band-gap reference to be enabled via the CVREF peripheral - if not initialized, touch readings will be inconsistent and may drift 50-100 counts across temperature.
Estimated: at 50 MHz operation with all peripherals active, the PIC32MX130F128HT-I/MR draws roughly 65 mA from VDD, dissipating about 215 mW. With a 64-QFN EP mounted on a 4-layer 1-oz copper PCB, theta_JA is approximately 28 C/W, giving a junction-to-ambient rise of 6 C above ambient at room temperature - well within the -40C to +85C industrial range. In sealed enclosures with no airflow, the same design may see 12-15 C of rise, leaving 50 C of margin.
Thông tin tuân thủ
RoHS and REACH compliant per Microchip product page. Industrial temperature grade (-40C to +85C); not AEC-Q100 qualified. For automotive, use the PIC32MK family.
