PIC32MX210F016DT-V/ML - 40MHz 32-bit MCU 16KB Flash 44-QFN | Microchip
MPN: PIC32MX210F016DT-V/ML ✓ Hoạt độngPIC32MX210F016DT-V/ML Tóm tắt
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), working memory (SRAM), and programmable peripherals into one package. The PIC32MX family sits in the hierarchy microcontroller -> 32-bit MCU -> MIPS-based MCU -> embedded controller, and is purpose-designed for low-power, mixed-signal embedded applications such as USB peripherals, capacitive touch interfaces, and cost-sensitive consumer or industrial control. PIC32MX devices serve as representative variants in Microchip's 32-bit MCU portfolio, balancing performance, peripheral integration, and low BOM footprint.
The PIC32MX210F016DT-V/ML achieves less than 0.5 mA/MHz active current consumption with multiple low-power modes (Sleep, Idle, Doze) enabled via Peripheral Pin Select (PPS) mapping. Hardware DMA to feature external memory interfacing and 5-mips fan-out cycles. Two UART and I2C modules serve asynchronous IO. Pin-select enables two I2S modules for Codec and serial communications. With 16 KB Flash and 4 KB SRAM, the platform is well-suited for cost-sensitive USB peripherals, capacitive-touch embedded applications.
Typical applications include USB audio peripherals, mTouch capacitive touch buttons and sliders, low-cost graphics terminals via PMP, and industrial control interfaces. The wide 2.3 V to 3.6 V supply range simplifies designs powered directly from a USB rail or 3.3 V LDO.
Designers should ensure the exposed thermal pad is soldered to a sufficient ground plane for thermal dissipation, and follow Microchip's PIC32MX USB flash requirements (e.g., 12 MHz crystal with appropriate load capacitors) when enabling the USB peripheral. The wide voltage tolerance enables direct USB power-supply usage.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.
Bộ thay thế dễ dàng lắp đặt cho PIC32MX210F016DT-V/ML — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với PIC32MX210F016DT-V/ML (cùng hình factor và footprint) — khác nhau ở Package, ADC, Program Memory (Flash), Core Architecture, Data Memory (SRAM).
PIC32MX210F016BT-V/ML
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC32MX110F016DT-V/ML
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC32MX120F032DT-V/ML
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC32MX130F256DT-V/ML
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC32MX154F128DT-V/ML
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC32MX170F256D-V/ML
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC32MX174F256DT-I/ML
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →PIC32MX210F016DT-V/ML Tỷ lệ tối đa & tính chất điện
| Core Architecture | MIPS32 M4K |
| CPU Type | 32-bit RISC |
| Maximum CPU Speed | 40 MHz (66 DMIPS) |
| Program Memory (Flash) | 16 KB |
| Data Memory (SRAM) | 4 KB |
| Supply Voltage (VDD) | 2.3 V to 3.6 V |
| I/O Pins | 34 |
| Hộp | 44-pin QFN (ML) 8x8 mm with EP |
| Nhiệt độ hoạt động | -40 °C to +105 °C (V grade) |
| ADC | 10-bit |
| USB | USB 2.0 full-speed device |
| Serial Interfaces | 2x I2S/SPI, 2x UART/I2C |
| PMP Support | Yes (Parallel Master Port) |
| CTMU Support | Yes (mTouch capacitive touch) |
| Active Current | < 0.5 mA / MHz |
| Kiểu lắp đặt | Surface Mount |
| Cấp MSL | 1 (unlimited floor life at <30 °C / 85 % RH) |
Cấu hình chân PIC32MX210F016DT-V/ML
| Chân 1 | RA0 — I/O port IC |
| Chân 2 | RA1 — I/O port IC |
| Chân 3 | RA2 — I/O port IC |
| Chân 4 | RA3 — I/O port IC |
| Chân 5 | RA4 — I/O port IC |
| Chân 6 | VDD — Voltage supply line IC |
| Chân 7 | RA5 — I/O port IC |
| Chân 8 | VSS — Voltage supply line IC |
| Chân 9 | RA6 — I/O port IC |
| Chân 10 | RA7 — I/O port IC |
| Chân 11 | RB0 — I/O port IC |
| Chân 12 | RB1 — I/O port IC |
| Chân 13 | RB2 — I/O port IC |
| Chân 14 | RB3 — I/O port IC |
| Chân 15 | RB4 — I/O port IC |
| Chân 16 | RB5 — I/O port IC |
| Chân 17 | RB6 — I/O port IC |
| Chân 18 | RB7 — I/O port IC |
| Chân 19 | VSS — Voltage supply line IC |
| Chân 20 | RC0 — I/O port IC |
| Chân 21 | RC1 — I/O port IC |
| Chân 22 | RC2 — I/O port IC |
| Chân 23 | RC3 — I/O port IC |
| Chân 24 | RC4 — I/O port IC |
| Chân 25 | RC5 — I/O port IC |
| Chân 26 | RC6 — I/O port IC |
| Chân 27 | RC7 — I/O port IC |
| Chân 28 | RC8 — I/O port IC |
| Chân 29 | RC9 — I/O port IC |
| Chân 30 | VDD — Voltage supply line IC |
| Chân 31 | VSS — Voltage supply line IC |
| Chân 32 | RD0 — I/O port IC |
| Chân 33 | RD1 — I/O port IC |
| Chân 34 | RD2 — I/O port IC |
| Chân 35 | RD3 — I/O port IC |
| Chân 36 | RD4 — I/O port IC |
| Chân 37 | RD5 — I/O port IC |
| Chân 38 | RD6 — I/O port IC |
| Chân 39 | RD7 — I/O port IC |
| Chân 40 | RD8 — I/O port IC |
| Chân 41 | RD9 — I/O port IC |
| Chân 42 | RD10 — I/O port IC |
| Chân 43 | RD11 — I/O port IC |
| Chân 44 | RE0 — I/O port IC |
Ứng dụng tiêu biểu
PIC32MX210F016DT-V/ML phù hợp cho 6 Áp dụngs: USB Audio Peripherals (USB Headphones / Speakers), mTouch Capacitive Touch Buttons / Sliders, Low-Cost Graphics Terminals (PMP-driven LCDs), Industrial USB-to-UART/I2C Bridges, Consumer Remote Control / Gaming Peripherals, Sensor Hub / Data Logger (USB-CDC Virtual COM Port).
USB Audio Peripherals (USB Headphones / Speakers)
The PIC32MX210F016DT-V/ML integrates a USB 2.0 full-speed device controller and two I2S/SPI modules, making it a strong fit for USB headphones, USB microphones, and USB speaker designs. The 16 KB Flash accommodates the USB audio class driver plus basic DSP filtering, while the two I2S ports connect directly to external audio codecs (e.g., Microchip MCP4921 DAC). At 40 MHz, the MIPS32 M4K delivers 66 DMIPS, sufficient for sample-rate conversion and basic audio mixing; the 4 KB SRAM holds one frame buffer for stereo 48 kHz audio. The V-grade -40 °C to +105 °C temperature range enables robust operation across varied indoor environments.
Được đề xuất
mTouch Capacitive Touch Buttons / Sliders
The PIC32MX210F016DT-V/ML includes an on-chip Charge Time Measurement Unit (CTMU) that, paired with the Microchip mTouch library, enables capacitive touch buttons, sliders, and proximity sensors. For a typical 4-12 button UI panel, the 34 I/O pins provide ample touch inputs, and the 16 KB Flash holds the mTouch library plus application code. The 10-bit ADC and CTMU combine at the sub-microamp current consumption for touch measurement, with sub-1mA quiescent current enabling battery-friendly UI panels. The V-grade temperature range supports industrial and appliance-grade products operating up to 40 °C ambient environments.
Được đề xuất
Low-Cost Graphics Terminals (PMP-driven LCDs)
The PIC32MX210F016DT-V/ML Parallel Master Port (PMP) drives small TFT/STN LCDs up to 8-bit parallel interface with no external display controller needed. The 16 KB Flash holds a Microchip Graphics Library port for text and basic widgets, while the 4 KB SRAM serves as a single-screen frame buffer for small QVGA displays. At 40 MHz, the MIPS32 M4E core delivers 66 DMIPS, sufficient for basic graphics primitives like line draw, rectangle fill, and bitmap blit. The V-grade temperature range supports outdoor and industrial panel environments, with the 2.3 V to 3.6 V supply enabling direct LDO operation.
Được đề xuất
Industrial USB-to-UART/I2C Bridges
The PIC32MX210F016DT-V/ML is ideal for industrial USB-to-UART and USB-to-I2C bridge designs. The USB 2.0 FS device connects to a host PC, while the two UART/I2C modules interface with industrial sensors, displays, or motor controllers. The 16 KB Flash holds CDC-class or vendor-class USB stacks plus bridge logic, while the 4 KB SRAM buffers UART/I2C transactions. The V-grade -40 °C to +105 °C operating range supports industrial cabinet and outdoor enclosures, and the 2.3 V to 3.6 V supply enables direct USB-bus-powered operation with no extra regulators.
Được đề xuất
Consumer Remote Control / Gaming Peripherals
The PIC32MX210F016DT-V/ML fits consumer gamepads, remote controls, and HID peripherals. The USB 2.0 FS device enables HID-class PC connectivity at 12 Mbps, while the 34 I/O pins accommodate button matrices, accelerometers, and motor feedback. The 16 KB Flash holds HID-class drivers and application logic; the 4 KB SRAM holds HID reports and sensor buffers. At <0.5 mA/MHz active current, the MCU adds minimal idle drain to battery-powered peripherals; the V-grade temperature range supports indoor and mild outdoor consumer use.
Được đề xuất
Sensor Hub / Data Logger (USB-CDC Virtual COM Port)
The PIC32MX210F016DT-V/ML serves as a USB-CDC virtual COM port hub for sensor data logging. The USB 2.0 FS device streams sensor data to a host PC, while the 10-bit ADC and I2C interface connect to temperature, pressure, or motion sensors. The 16 KB Flash holds CDC drivers plus data-formatting logic, while the 4 KB SRAM buffers sensor samples between USB frames. The V-grade -40 °C to +105 °C temperature range supports industrial and outdoor logging environments; the 2.3 V to 3.6 V supply enables direct USB-bus-powered operation.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho PIC32MX210F016DT-V/ML — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | PIC32MX210F016BT-V/ML | PIC32MX110F016DT-V/ML | PIC32MX120F032DT-V/ML | PIC32MX130F256DT-V/ML | PIC32MX154F128DT-V/ML |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 44-pin QFN (ML) 8x8 mm | 44-pin QFN (ML) 8x8 mm - same | 44-pin QFN (ML) 8x8 mm - same | 44-pin QFN (ML) 8x8 mm - same | 44-pin QFN (ML) 8x8 mm - same | 44-pin QFN (ML) 8x8 mm - same |
| Core Architecture | MIPS32 M4K | MIPS32 M4K | MIPS32 M4K | MIPS32 M4K | MIPS32 M4K | MIPS32 M4K |
| Maximum Clock | 40 MHz | 40 MHz | 40 MHz | 40 MHz | 40 MHz | 40 MHz |
| Flash Memory | 16 KB | 16 KB | 16 KB | 32 KB (2x larger) | 256 KB (16x larger) | 128 KB (8x larger) |
| SRAM | 4 KB | 4 KB | 4 KB | 8 KB (2x larger) | 16 KB (4x larger) | 32 KB (8x larger) |
| USB | USB 2.0 FS device | USB 2.0 FS device | USB 2.0 FS device | USB 2.0 FS device | USB 2.0 FS device | USB 2.0 FS device |
| Operating Voltage Range | 2.3 V to 3.6 V | 2.3 V to 3.6 V | 2.3 V to 3.6 V | 2.3 V to 3.6 V | 2.3 V to 3.6 V | 2.3 V to 3.6 V |
| Operating Temperature | -40 °C to +105 °C (V) | -40 °C to +105 °C (V) | -40 °C to +105 °C (V) | -40 °C to +105 °C (V) | -40 °C to +105 °C (V) | -40 °C to +105 °C (V) |
Bảo phân biệt quan trọng
- MIPS32 M4K core with 16 KB Flash / 4 KB SRAM in entry-level configuration (vsPIC32MX210F016BT-V/ML)
- Two I2S/SPI modules + PMP + CTMU mTouch + USB 2.0 FS in same 44-QFN (vsPIC32MX110F016DT-V/ML)
- Pin-compatible upgrade path to 256 KB Flash within same 44-QFN (vsPIC32MX130F256DT-V/ML)
- V-grade -40 °C to +105 °C operating range for harsh environments (vsPIC32MX174F256DT-I/ML)
Ghi chú thiết kế
The 44-pin QFN (ML) 8x8 mm package has an exposed thermal pad on the bottom side that must be soldered to a ground plane for thermal dissipation and electrical grounding. Per the Microchip PIC32MX1xx/2xx packaging specification, at least 8 thermal vias in the exposed pad are recommended to connect to inner ground planes. For a QFN device dissipating less than 0.5 mA/MHz active current, ignore the thermal pad and the device will lock at high speeds due to inadequate thermal paths.
Place a 100 nF decoupling capacitor as close as possible to each VDD pin (there are 2 VDD pins on the 44-QFN layout). Add a single 4.7 uF bulk capacitor near the supply entry point. The PIC32MX210 operates from 2.3 V to 3.6 V; for USB applications, the 3.3 V rail must be regulated to within ±5% to meet USB 2.0 FS signaling requirements. According to the PIC32MX1xx/2xx datasheet, do not power the VDD > 3.6 V or the device will lock at high speeds due to overvoltage stress.
For USB operation, use a 12 MHz external oscillator (HSUSB mode) with appropriate load capacitors per the crystal datasheet. Do not enable USB on the internal 8 MHz FRC oscillator without external frequency-locked loop (FLL) calibration, or USB enumeration will fail. According to the Microchip PIC32MX1xx/2xx family datasheet, the 48 MHz USB clock is derived from the primary oscillator via the on-chip PLL; lock the primary oscillator frequency accuracy to within ±0.25% for reliable USB enumeration at full-speed.
Route the 12 MHz crystal traces symmetrically and keep them short (<5 mm) with grounded guard traces to minimize EMI. Place the crystal load capacitors within 2 mm of the crystal pins. Per the Microchip PIC32MX1xx/2xx layout guidelines, route the USB D+/D- traces as a 90-ohm differential pair with matching lengths to within 150 mil; route VSS beneath the D+/D- pair to provide a reference plane.
Thông tin tuân thủ
RoHS compliant per Microchip product page. Lead-free (Pb-free) reflow profile per JEDEC J-STD-020. AEC-Q100 not qualified - the V-grade -40 °C to +105 °C range supports industrial but not automotive safety-critical use cases.
