R5F117BCGNA#20 - 16-Bit 24MHz 32KB RL78/I1D MCU | Renesas
MPN: R5F117BCGNA#20 ✓ Hoạt độngR5F117BCGNA#20 Tóm tắt
A microcontroller is a programmable semiconductor that integrates a CPU core, memory, analog conversion, and peripheral interfaces onto one device. The RL78 family is based on a 16-bit CISC architecture and is widely used in industrial control, metering, sensing, and embedded equipment where compact size, low power consumption, and analog signal handling are important. The R5F117BCGNA#20 belongs to the RL78/I1D series, which emphasizes enhanced analog functions rather than high-speed digital connectivity.
The device provides 32 KB of flash program memory organized as 32K x 8. Its integrated analog resources include operational amplifiers, a 12-bit A/D converter, and window comparators, allowing a board to condition and monitor sensor signals without relying on several separate analog components. The 24 MHz operating frequency supports responsive control-loop execution while the low-power design remains suitable for battery-operated and energy-conscious instruments.
The 32-HVQFN 5 x 5 mm package keeps the PCB footprint compact but makes thermal-pad layout and careful paste-stencil design important during assembly. The exposed-pad construction supports heat transfer to the PCB, which is particularly valuable when the analog circuitry, converter, and CPU operate continuously. Board designers should follow the manufacturer land-pattern and solder-mask guidance rather than treating the HVQFN as a generic QFN.
Typical applications include industrial detector modules, environmental and gas sensors, smart sensor nodes, compact instrumentation, battery-powered measurement products, and control boards where analog front ends and microcontroller processing are combined. The R5F117BCGNA#20 is also appropriate for designs requiring a -40°C to +105°C temperature range, provided the PCB, crystal or clock source, analog reference, and external components are rated for the same environmental range.
For new designs, first confirm the RL78/I1D peripheral mapping, pin multiplexing, and exposed-pad connection in the manufacturer datasheet and pin-description table. Keep analog inputs short, place bypass capacitors close to the supply pins, and route the analog ground reference carefully to minimize conversion noise. This page combines package and application analysis with drop-in substitution guidance and practical board-level design notes.
Bộ thay thế dễ dàng lắp đặt cho R5F117BCGNA#20 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
R5F117BCGNA#00
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
R5F104BCAFP#V0
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
R5F117BCGNA#20 Tỷ lệ tối đa & tính chất điện
| Manufacturer | Renesas Electronics |
| Series | RL78/I1D |
| Architecture | 16-bit |
| Tần số xung maksimum | 24 MHz |
| Flash Memory | 32 KB (32K x 8) |
| Hộp | 32-HVQFN (5 x 5 mm) with exposed pad |
| Khoảng nhiệt độ hoạt động | -40°C to +105°C |
| A/D Converter | 12-bit |
| Operational Amplifiers | Integrated |
| Window Comparators | Integrated |
| Kiểu lắp đặt | Surface mount |
| Product Category | Microcontrollers - MCU |
| Core Series | RL78 |
| Program Memory Organization | 32K x 8 bytes |
| Package Body Size | 5 x 5 mm |
| Số chân | 32 pins including exposed pad |
Hướng dẫn cấu hình chân R5F117BCGNA#20 5 x 5 mm
Cấu hình chân cho R5F117BCGNA#20 (5 x 5 mm gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho R5F117BCGNA#20.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
R5F117BCGNA#20 phù hợp cho 6 Áp dụngs: Industrial Gas and Environmental Sensors, Battery-Powered Measurement Instruments, Precision Detector Control Boards, Smart Sensor Hubs, Compact Industrial Control Modules, Low-Power Sensor Nodes.
Industrial Gas and Environmental Sensors
The R5F117BCGNA#20 fits environmental and gas-sensing modules because its integrated 12-bit A/D converter, operational amplifiers, and window comparators can condition a sensor output, digitize it, and detect upper and lower thresholds without several separate analog ICs. The 24 MHz 16-bit RL78 core provides enough control-loop performance for compensation, filtering, and sensor-state management. Its 32 KB of flash accommodates calibration tables, compensation coefficients, and diagnostic logic. In a battery-powered design, the low-power-oriented RL78/I1D architecture supports duty-cycled measurement, while the -40°C to +105°C range supports industrial environments. Keep sensor traces away from switching nodes and route the analog reference directly to the converter and amplifier supply pins.
Được đề xuất
Battery-Powered Measurement Instruments
The R5F117BCGNA#20 suits compact battery-powered instruments where analog conditioning, conversion, and control must coexist on a small board. Its 32-HVQFN 5 x 5 mm package limits footprint, while 32 KB of flash provides space for measurement algorithms and data buffering. The 12-bit A/D converter and integrated operational amplifiers can directly handle sensor outputs, reducing the component count and potential board area. The 24 MHz RL78 core supports responsive sampling and display or communication updates. Because the MCU and analog blocks share a constrained power budget, the design should use the device's low-power modes between measurements, disable unused analog channels, and follow the manufacturer layout guidance to minimize conversion noise.
Được đề xuất
Precision Detector Control Boards
The R5F117BCGNA#20 is well suited to detector control boards because it combines a 24 MHz 16-bit control processor with a 12-bit A/D converter, operational amplifiers, and window comparators. A detector front end can therefore be sampled and evaluated for over-range, under-range, or drift conditions while the CPU manages calibration and output state. The 32 KB of flash is useful for storing thresholds, correction data, and event logic. For industrial detector equipment, the -40°C to +105°C operating range supports operation across controlled machinery and ambient conditions. Place analog input components close to the relevant device pins, use a quiet analog ground strategy, and validate comparator thresholds with sufficient margin over worst-case process, temperature, and reference-voltage variation.
Được đề xuất
Smart Sensor Hubs
The R5F117BCGNA#20 can act as the central controller in a smart sensor hub that gathers analog measurements from resistive, capacitive, or current-based sensing elements. Its integrated operational amplifiers condition low-level inputs before the 12-bit A/D converter performs sampling, and the window comparators can quickly flag measurements outside programmed limits. The 24 MHz 16-bit core supports filtering and local decision-making, while 32 KB of flash can hold configuration and calibration data. The compact 32-HVQFN 5 x 5 mm package helps when several sensor channels must fit into a confined enclosure. Maintain separate analog and digital return-current paths, keep capacitor ESR and placement within the datasheet recommendations, and isolate high-current loads from sensitive sensor traces.
Được đề xuất
Compact Industrial Control Modules
The R5F117BCGNA#20 supports compact industrial control modules that must read analog process values and execute control logic within limited board space. The 32-HVQFN package reduces footprint, and the exposed pad provides a direct thermal path into the PCB when continuous operation increases dissipation. The 24 MHz RL78 core can service control loops and supervisory tasks, while the integrated 12-bit converter, amplifiers, and window comparators simplify analog front-end integration. The -40°C to +105°C range suits equipment deployed outside tightly controlled indoor environments. Design the thermal pad and copper pour according to the manufacturer package recommendations, keep high-current switching paths away from analog inputs, and verify grounding and filtering against the accuracy required by the process measurement.
Được đề xuất
Low-Power Sensor Nodes
The R5F117BCGNA#20 is appropriate for distributed low-power sensor nodes that periodically sample an analog input and report the result. Its integrated analog blocks can shorten the signal chain by combining amplification, conversion, and threshold comparison around the 24 MHz 16-bit processor. The 32 KB of flash supports protocol handlers, configuration, and calibration without requiring a larger memory footprint. Renesas identifies the RL78/I1D family for detectors and sensors requiring low power and analog integration, making sleep-mode behavior and wake-up timing central to the design. Verify the operating current in each required mode, disable unused peripherals, use the documented clock configuration, and confirm that the analog stabilization time meets the sampling interval.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho R5F117BCGNA#20 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | R5F117BCGNA#00 | R5F104BCAFP#V0 |
|---|---|---|---|
| Package | 32-HVQFN (5 x 5 mm) with exposed pad | 32-HVQFN (5 x 5 mm) with exposed pad | 32-pin LQFP per listed comparison data; footprint compatibility requires verification |
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Series | RL78/I1D | RL78/I1D | RL78 |
| CPU Architecture | 16-bit | 16-bit | 16-bit |
| Flash Memory | 32 KB (32K x 8) | 32 KB | 32 KB |
Bảo phân biệt quan trọng
- The strongest documented same-package substitution candidate (vsR5F117BCGNA#00)
- Analog integration reduces the need for separate support ICs (vsR5F104BCAFP#V0)
- Extended-temperature capability for industrial sensor products (vsR5F117BCGNA#00)
Ghi chú thiết kế
Keep analog inputs, the 12-bit A/D converter, and integrated operational-amplifier connections away from switching-node traces and high-current return paths. Use a continuous analog ground plane where the layout guidance permits, connect analog and digital returns at a controlled point, and place input bypass capacitors adjacent to the relevant supply pins. Short traces and low-loop-area grounding reduce conversion errors that are otherwise attributed to the MCU.
The 32-HVQFN exposed pad is the primary thermal path from the device to the PCB. Follow the manufacturer land pattern, fill the thermal-via requirement specified for the selected PCB stack-up, and avoid placing thermal-via stubs directly beneath sensitive analog inputs. Estimate the junction temperature from the calculated device dissipation and the actual copper area rather than assuming that the package rating applies without thermal-pad attachment.
Do not assign MCU functions from the package outline alone. The 32-HVQFN combines 32 pins and an exposed pad, while the RL78/I1D platform uses multiplexing and several options for high-voltage, analog, and peripheral assignments. Use the manufacturer pin-description table for every net, confirm the exposed-pad connection, and verify the package code in the ordering information before releasing artwork.
Estimate power use for both the active and sleep phases because battery-operated sensor designs are usually constrained by average current rather than peak current. Include the 12-bit converter, operational amplifiers, and any enabled window comparators in the active-load calculation. After implementation, measure current in each operating mode and verify that the analog settling time is acceptable for the intended sampling cycle.
Thông tin tuân thủ
No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations were identified. AEC-Q100 is not applicable because the R5F117BCGNA#20 is an industrial microcontroller rather than an automotive-qualified device.