STM32F401CCU7 - 84MHz Cortex-M4 MCU, 256KB Flash | STMicroelectronics
MPN: STM32F401CCU7 ✓ Hoạt độngSTM32F401CCU7 Tóm tắt
A microcontroller is a programmable system-on-chip that executes firmware, reads sensors, controls peripherals, and exchanges data with other systems. STM32F401 devices sit within the STM32 family, use the Arm Cortex-M4 processor core, and belong to the broader embedded MCU and embedded-processing semiconductor categories. Their combination of moderate processing performance, integrated memory, and compact packaging supports cost-sensitive embedded control while retaining useful DSP and floating-point capability.
Key features include a 32-bit Cortex-M4 core, an integrated FPU, 84 MHz maximum operating frequency, and 105 DMIPS performance. The 256 KB Flash provides embedded code and nonvolatile data storage, while 64 KB of RAM supports working memory and stack requirements. Multiple timers, one ADC, and 11 communication interfaces allow the MCU to consolidate sensing, timing, control, and external connectivity functions on a single device.
The architecture supports connected industrial, medical, consumer, and communications equipment where a compact controller must combine real-time control with manageable memory requirements. The single ADC and extensive peripheral set reduce the need for external components in moderate signal-processing designs, while the Cortex-M4 FPU accelerates floating-point calculations used in filtering, control, and sensor-conditioning algorithms. Software compatibility across the STM32 ecosystem can simplify firmware reuse and qualification.
Typical uses include industrial sensor controllers, building automation modules, compact motor-control subsystems, medical monitoring equipment, communications equipment, and consumer accessories. The 48-pin UFQFPN package supports dense PCB layouts, but its exposed thermal pad and fine-pitch leads require careful layout, assembly, and thermal-management practices.
For a new PCB, follow the pin-description table and recommended land pattern in the STMicroelectronics STM32F401 datasheet. Place all decoupling capacitors close to their supply pins, connect the exposed pad to the ground plane according to the datasheet layout, and verify signal-level compatibility before substituting the device in an existing design.
This page organizes the STM32F401CCU7 specifications, sourcing information, pinout resource, same-package alternatives, and practical integration guidance to support faster component selection and hardware planning.
Bộ thay thế dễ dàng lắp đặt cho STM32F401CCU7 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
STM32F401CCU6TR
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
STM32F401CCU7 Tỷ lệ tối đa & tính chất điện
| Product Type | 32-bit Arm Cortex-M4 microcontroller with FPU |
| Processor Core | Arm Cortex-M4 |
| Architecture | ARM 32-bit |
| Maximum CPU Frequency | 84 MHz |
| Peak Processing Performance | 105 DMIPS |
| Flash Memory | 256 KB |
| Flash Organization | 256K x 8 bits |
| RAM | 64 KB |
| Timer Count | 11 timers |
| ADC Count | 1 ADC |
| Communication Interface Count | 11 communication interfaces |
| Supply Voltage Options | 1.8 V, 2.5 V, or 3.3 V |
| Hộp | 48-pin UFQFPN |
| Package Dimensions | 7 x 7 mm |
| Exposed Pad | Yes |
| Kiểu lắp đặt | Surface mount |
| Delivery Format | Tray |
| Floating-Point Unit | Integrated |
Hướng dẫn cấu hình chân STM32F401CCU7 7 x 7 mm
Cấu hình chân cho STM32F401CCU7 (7 x 7 mm gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho STM32F401CCU7.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
STM32F401CCU7 phù hợp cho 6 Áp dụngs: Industrial Sensor Controller, Building Automation Module, Medical Monitoring Device, Compact Communications Controller, Motor and Actuator Control, Portable Consumer Accessory.
Industrial Sensor Controller
The STM32F401CCU7 fits compact industrial sensor controllers that combine periodic acquisition with local decision-making. Its 84 MHz Cortex-M4 core and integrated FPU can process filtered measurements, while one ADC supports suitable analog-sensing channels and 11 timers provide timing resources for sampling and control tasks. The 256 KB Flash stores application firmware, calibration logic, and protocol handlers, while 64 KB RAM accommodates buffers and control state. Its 48-pin UFQFPN package reduces board area, although the exposed pad and fine-pitch routing require careful PCB layout and thermal control.
Được đề xuất
Building Automation Module
The STM32F401CCU7 is appropriate for building automation modules that supervise sensors, coordinate outputs, and maintain communications over a local network. Its 11 timers can organize periodic sensing and actuator timing, and the 11 communication interfaces support multiple serial protocols within the STM32F4 family. The 84 MHz Cortex-M4 performance leaves useful headroom for filtering, state management, and protocol processing, while 256 KB of Flash accommodates a substantial embedded application. A 1.8 V, 2.5 V, or 3.3 V supply configuration allows alignment with the selected communications and sensor ecosystem.
Được đề xuất
Medical Monitoring Device
The STM32F401CCU7 can serve as the control processor in a compact medical monitoring device that samples limited analog signals and performs local signal processing. The integrated FPU supports efficient floating-point filtering and calculations, while the 84 MHz CPU can manage acquisition timing and user-interface tasks. Its 64 KB RAM and 256 KB Flash provide a balanced embedded footprint for connected monitoring products. Compliance must be evaluated at the finished-product level, including the exact ordering grade, applicable medical standards, electrical safety requirements, and risk-control processes rather than relying only on general MCU specifications.
Được đề xuất
Compact Communications Controller
The STM32F401CCU7 suits compact communications controllers that must manage serial links, framing, and application-layer logic in a small embedded enclosure. The 11 communication interfaces provide broad protocol-oriented peripheral support, while the Cortex-M4 FPU at 84 MHz offers sufficient throughput for buffering, filtering, and packet processing. The 48-pin UFQFPN footprint supports dense layouts where board area is constrained, and the 256 KB Flash can hold networking stacks or application firmware. Exact transceiver and protocol compatibility should be established from the manufacturer peripheral matrix and pin table.
Được đề xuất
Motor and Actuator Control
The STM32F401CCU7 can support compact motor or actuator-control subsystems that require deterministic periodic timing and embedded control calculations. Eleven timers provide a substantial timing foundation for PWM, input capture, and synchronization functions, while the 84 MHz Cortex-M4 core and FPU can execute filtering and control algorithms. Its 256 KB Flash and 64 KB RAM are suitable for moderate embedded-control workloads without requiring an external microcontroller. Power-stage design, thermal performance, and safety behavior remain system-level responsibilities, particularly where mains-connected or safety-related operation is required.
Được đề xuất
Portable Consumer Accessory
The STM32F401CCU7 fits portable consumer accessories that combine local control, analog sensing, and compact serial connectivity. Its low-density 48-pin package supports space-constrained assemblies, while the Cortex-M4 FPU provides practical signal-processing performance without a larger processor. The 256 KB Flash is suitable for embedded UI logic, communication handlers, and configuration data, and 64 KB RAM supports working buffers. Designers should use the exposed-pad land pattern and place decoupling capacitors according to the manufacturer guidance to preserve signal and thermal performance in a densely assembled enclosure.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho STM32F401CCU7 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | STM32F401CCU6TR |
|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics |
| Package | 48-pin UFQFPN (7 x 7 mm) | 48-pin UFQFPN (7 x 7 mm) |
| Processor Core | Arm Cortex-M4 | Arm Cortex-M4 |
| Maximum CPU Frequency | 84 MHz | 84 MHz |
| Flash Memory | 256 KB | 256 KB |
| RAM | 64 KB | 64 KB |
| Floating-Point Unit | Integrated | Integrated |
| Ordering Grade | U7 | U6 |
Bảo phân biệt quan trọng
- Compact 48-pin implementation with substantial embedded memory (vsSTM32F401CCU6TR)
- Floating-point processing in a compact MCU package (vsSTM32F401CCU6TR)
- Integration for embedded sensing and timing (vsSTM32F401CCU6TR)
Ghi chú thiết kế
Use the STM32F401 datasheet land pattern and pin-description table as the authority for the 48-pin UFQFPN footprint. Place required decoupling capacitors directly beside their associated supply and ground balls, keep the exposed-pad connection and thermal-via arrangement consistent with the reference layout, and verify courtyard clearance against the selected assembler. A fine-pitch QFN can appear electrically correct in schematic review yet become difficult to assemble if pads, vias, or solder mask openings are modified without manufacturer guidance.
Design separate, low-impedance paths for the MCU supply domains and connect each decoupling point close to the relevant package ball. Confirm regulator ripple, startup sequencing, voltage tolerances, and I/O limits against the selected 1.8 V, 2.5 V, or 3.3 V configuration. Do not route high-current return paths through the exposed pad area in a way that adds voltage noise to sensitive ground references. The manufacturer power-supply and decoupling recommendations should be copied exactly into the schematic and layout.
The exposed pad is a central thermal and electrical feature, not an unused lead. Provide the recommended ground-plane connection and vias so heat can spread away from the device under sustained 84 MHz operation. Estimate junction temperature from actual regulator dissipation, ambient temperature, board construction, and the package thermal data before defining the maximum operating duty cycle. Copper area on a small board can be limited, so enclosure airflow and load profile may require validation in the final mechanical assembly.
Do not treat another STM32F4 member as a drop-in part merely because it uses 48 pins. Verify the exact package drawing, exposed-pad requirements, power pins, oscillator connections, debug pins, alternate functions, and peripheral availability. When evaluating the STM32F401CCU6TR, confirm the operating-temperature grade and delivery format. Also check whether existing firmware relies on a peripheral or pin position not present in the selected variant, and run peripheral, clock, brownout, and full production-board validation before releasing an alternate MPN.
Thông tin tuân thủ
The manufacturer ordering information must be consulted for the exact package, temperature grade, and compliance declarations. No specific compliance claim is made for this exact ordering code.