STM32G031F8P3TR - 64MHz Cortex-M0+ 64KB Flash | STMicroelectronics
MPN: STM32G031F8P3TR ✓ Hoạt độngSTM32G031F8P3TR Tóm tắt
Bộ thay thế dễ dàng lắp đặt cho STM32G031F8P3TR — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với STM32G031F8P3TR (cùng hình factor và footprint) — khác nhau ở Flash Memory, Mounting Type, Package, Core, SRAM.
STM32G031F8P6TR
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
STM32G031F6P7
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
STM32G031F6P6
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →STM32G031F8P3
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →STM32G030F6P6TR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →STM32G031F8P3TR Tỷ lệ tối đa & tính chất điện
| Core | Arm Cortex-M0+ |
| Architecture | 32-bit RISC |
| Maximum CPU Frequency | 64 MHz |
| Flash Memory | 64 KB |
| SRAM | 8 KB |
| Operating Voltage | 2.5 V to 3.3 V |
| Hộp | 20-pin TSSOP |
| Kiểu lắp đặt | Surface Mount |
| Product Family | STM32G0 mainstream |
| Device Type | Microcontroller IC |
| Manufacturer | STMicroelectronics |
| Ordering Suffix | P3TR |
Hướng dẫn cấu hình chân STM32G031F8P3TR 20-pin tssop
Cấu hình chân cho STM32G031F8P3TR (20-pin tssop gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho STM32G031F8P3TR.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
STM32G031F8P3TR phù hợp cho 6 Áp dụngs: Compact Industrial Control Module, Small Motor Controller, USB Peripheral and Consumer Electronics, Sensor and IoT Controller, LED Lighting Controller, Battery-Powered Measurement Device.
Compact Industrial Control Module
The STM32G031F8P3TR fits compact industrial controllers that need deterministic embedded processing without a large microcontroller package. Its Arm Cortex-M0+ core operates up to 64 MHz, while 64 KB of Flash and 8 KB of SRAM provide room for control firmware, parameter storage, and runtime buffers. The 20-pin TSSOP package reduces board area and supports cost-effective surface-mount assembly. Designers should confirm timer, ADC, communication, and GPIO assignments in the manufacturer datasheet before assigning industrial inputs, outputs, and communication lines.
Được đề xuất
Small Motor Controller
STM32G031F8P3TR is appropriate for small motor-control subsystems where a compact MCU must execute a control loop and coordinate peripheral functions. The 64 MHz Cortex-M0+ core provides responsive instruction execution, and the 64 KB Flash and 8 KB SRAM support embedded control code, parameters, and status data. The 20-pin TSSOP footprint can save board space in a compact controller. Confirm the required PWM channels, timer architecture, ADC characteristics, pin multiplexing, and thermal conditions in the manufacturer documentation for the specific motor and driver stage.
Được đề xuất
USB Peripheral and Consumer Electronics
The STM32G031F8P3TR can serve as the central MCU in compact USB-enabled peripheral and consumer products. Its Cortex-M0+ core at up to 64 MHz is suitable for protocol handling, configuration, and local control, while 64 KB Flash and 8 KB SRAM provide a practical embedded memory budget. The 20-pin TSSOP package supports dense boards and automated assembly. Check the exact USB, bootloader, crystal, and GPIO requirements in the manufacturer datasheet, because peripheral availability and pin assignment depend on the selected STM32G031 variant.
Được đề xuất
Sensor and IoT Controller
STM32G031F8P3TR is well suited to compact IoT and sensor-controller boards that must acquire, process, and transmit limited amounts of data. The 64 MHz core can service protocol tasks and control logic, while 64 KB Flash and 8 KB SRAM accommodate firmware, calibration values, and short-lived sensor data. Its small 20-pin TSSOP package enables placement close to sensors and communication hardware. Verify ADC performance, serial-interface pin availability, clocking, and low-power modes in the manufacturer datasheet for the intended sensing chain.
Được đề xuất
LED Lighting Controller
The STM32G031F8P3TR can implement compact LED-lighting controllers where timing, communication, and user-interface logic must coexist in a small board. Its 64 MHz Cortex-M0+ core supports PWM and control-loop execution, and the 64 KB Flash and 8 KB SRAM are sufficient for embedded lighting firmware and configuration storage. The 20-pin TSSOP footprint allows the controller to be placed close to the LED driver circuitry. Confirm timer channels, PWM resolution, communication peripherals, and output-pin electrical limits in the manufacturer datasheet.
Được đề xuất
Battery-Powered Measurement Device
STM32G031F8P3TR is appropriate for compact battery-powered measurement products where the controller must balance processing capability, memory, and board size. The 2.5 V to 3.3 V operating range supports common low-voltage embedded platforms, while the 64 MHz core provides enough throughput for acquisition control and data processing. The 20-pin TSSOP package minimizes footprint and can simplify assembly in high-volume designs. Verify low-power behavior, ADC accuracy, timer resources, and analog pin constraints against the manufacturer datasheet before setting the battery budget.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho STM32G031F8P3TR — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | STM32G031F8P6TR | STM32G031F6P7 | STM32G031F6P6 | STM32G030F6P6TR |
|---|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Package | 20-pin TSSOP | 20-pin TSSOP | 20-pin TSSOP | 20-pin TSSOP | 20-pin TSSOP |
| Product Positioning | STM32G031 mainstream microcontroller | STM32G031 family | STM32G031 family | STM32G031 family | STM32G030 family |
Bảo phân biệt quan trọng
- Mainstream STM32G031 device with 64 KB Flash and 8 KB SRAM (vsSTM32G030F6P6TR)
- Compact 20-pin TSSOP integration (vsSTM32G031G8U6)
- 64 MHz Cortex-M0+ processing in a low-cost MCU (vsSTM32G031F8P6TR)
Ghi chú thiết kế
Design the 2.5 V to 3.3 V power rails with the decoupling and startup behavior specified in the manufacturer datasheet. Place the required input and output capacitors close to the appropriate power pins, keep the ground return path continuous, and verify the supply ramp against reset and boot requirements. The 64 MHz operating speed and peripheral configuration should be validated under the intended voltage and temperature conditions before production release.
Use the manufacturer TSSOP-20 land pattern and pin-description table for the PCB footprint. Preserve the package orientation marking, keep the pin-1 side identifiable, and route SWD programming, reset, clock, and ground signals for reliable programming and field service. The compact 20-pin package limits routing flexibility, so assign pins against the final peripheral mix rather than relying on a generic STM32G0 layout.
Do not treat an STM32G031 ordering suffix change as automatically drop-in. Confirm package pinout, Flash and SRAM capacity, voltage range, temperature grade, clock configuration, and peripheral resources against the exact replacement datasheet. The 64 KB Flash and 8 KB SRAM values apply to STM32G031F8P3TR and must not be assumed for related F6 or G0 variants.
For analog sensing, communication, or motor-control connections, isolate sensitive signal routing from fast-switching nodes and keep return paths short. Check the ADC, timer, communication, and pin-multiplexing requirements before finalizing the layout. The Cortex-M0+ core can operate at 64 MHz, so clock distribution and signal-integrity margin should be evaluated on the assembled board rather than inferred only from the nominal frequency.
Thông tin tuân thủ
Compliance information is not stated in the verified manufacturer or distributor excerpts. Confirm RoHS, REACH, automotive qualification, lead-free, halogen-free, and conflict-minerals status in the manufacturer documentation before release.