STMicroelectronics

STM32L031G6U6 - 32MHz Cortex-M0+ MCU, 32KB Flash | STMicroelectronics

MPN: STM32L031G6U6 ✓ Hoạt động
28-pin UFQFPN, 4 x 4 mm Package 32 MHz Speed 32 KB Memory
MOQ: 1 |

STM32L031G6U6 Tóm tắt

The STMicroelectronics STM32L031G6U6 is an ultra-low-power 32-bit Arm Cortex-M0+ microcontroller with a 32 MHz operating frequency, 32 KB of Flash program memory, 8 KB of RAM, and 1 KB of EEPROM in a 28-pin UFQFPN package. It belongs to the STM32L0 access-line family of low-power microcontrollers, combining a compact 4 x 4 mm footprint with energy-conscious embedded control.

A microcontroller is a programmable semiconductor device that integrates a CPU core, memory, and peripherals into one package. The Cortex-M0+ processor belongs to the Arm Cortex-M family and is designed for cost-sensitive embedded systems. In the power-management hierarchy, the STM32L031G6U6 is a battery-friendly embedded controller that can execute firmware while limiting standby and active-mode energy consumption.

Key specifications include a 32-bit Arm Cortex-M0+ core operating at 32 MHz, 32 KB of Flash for program storage, 8 KB of SRAM for working data, and 1 KB of EEPROM for nonvolatile parameter retention. The device also provides an extended I/O and peripheral set for low-power sensing, communication, control, and embedded accessory applications. Its 28-UFQFPN 4 x 4 mm package supports compact PCB designs where board area is constrained.

The STM32L031G6 family combines a straightforward Cortex-M0+ architecture with ultra-low-power operating modes. This makes it suitable for products that spend most of their service life in low-energy states, including portable sensors, compact industrial controls, compact accessories, and connected embedded nodes. Firmware can remain in low-power states between measurements or user interactions, reducing the energy burden associated with continuously powered systems.

Typical uses include battery-powered sensor nodes, compact industrial monitoring devices, low-power accessory controllers, home-automation endpoints, portable measurement instruments, and small motor or actuator control boards. The 32 MHz core provides adequate responsiveness for event-driven control, protocol handling, and moderate peripheral workloads without requiring a higher-performance Cortex-M processor.

When laying out a circuit, follow the manufacturer’s UFQFPN land pattern and pin-definition tables exactly. Keep power and decoupling connections short, provide the required clock and reset arrangements, and verify the exposed-pad connection and thermal strategy. Firmware migration between STM32L0 devices should also be checked against memory size, peripheral availability, and package pin assignment.

This product page combines the manufacturer’s core specifications, package details, source links, application guidance, and qualified replacement analysis to support faster component selection, schematic review, and sourcing decisions.

Bộ thay thế dễ dàng lắp đặt cho STM32L031G6U6 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.

Các biến thể trong loạt này

Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với STM32L031G6U6 (cùng hình factor và footprint) — khác nhau ở Maximum CPU Frequency, Package, Product Type, Flash Organization.

STMicroelectronics
Maximum CPU Frequency: 48 MHz
Package: 28-pin UFQFPN (4 mm x 4 mm)
Product Type: 32-bit ARM Cortex-M0 microcontroller
So sánh với STM32L031G6U6 →
STMicroelectronics
Maximum CPU Frequency: 32 MHz
Package: 28-pin UFQFPN, 4 x 4 mm
Product Type: 32-bit ultra-low-power microcontroller
So sánh với STM32L031G6U6 →

STM32F042G6U6

✅ Drop-In
STMicroelectronics
📦 28-UFQFPN (4x4)
32-bit ARM Cortex-M0 microcontroller · 48 MHz · ARM Cortex-M0 32-bit RISC · 32 KB · 32K x 8 bits · 28-pin UFQFPN (4 mm x 4 mm) · Surface mount · Supported

Liên hệ để biết giá

Xem tài liệu →

STM32L031G6U6 Tỷ lệ tối đa & tính chất điện

Product Type 32-bit ultra-low-power microcontroller
Processor Core Arm Cortex-M0+
CPU Architecture 32-bit RISC
Maximum CPU Frequency 32 MHz
Flash Memory 32 KB
Flash Organization 32K x 8
SRAM 8 KB
EEPROM 1 KB
Hộp 28-pin UFQFPN, 4 x 4 mm
Kiểu lắp đặt Surface mount
Khoảng nhiệt độ hoạt động -40 °C to +85 °C
Product Series STM32L0 access line

Hướng dẫn cấu hình chân STM32L031G6U6 28-pin ufqfpn, 4 x 4 mm

Cấu hình chân cho STM32L031G6U6 (28-pin ufqfpn, 4 x 4 mm gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.

Bảng cấu hình chân 28-pin ufqfpn, 4 x 4 mm cho STM32L031G6U6

Không có dữ liệu chân cụ thể sẵn có cho STM32L031G6U6.

Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.

Ứng dụng tiêu biểu

STM32L031G6U6 phù hợp cho 6 Áp dụngs: Battery-Powered Sensor Node, Compact Industrial Monitoring Controller, Low-Power Home Automation Endpoint, Portable Measurement Instrument, Compact Accessory Controller, Smart Lighting Control Module.

🧩

Battery-Powered Sensor Node

The STM32L031G6U6 fits compact battery-powered sensing products because its 32 MHz Cortex-M0+ core provides enough processing capability for event-driven measurement, filtering, and local control while the device can use the low-power modes of the STM32L0 family. Its 32 KB of Flash accommodates a compact firmware image, while 8 KB of RAM supports protocol state and sensor buffering. The 28-UFQFPN 4 x 4 mm package also reduces board area compared with larger leaded or QFP controllers. Design the duty cycle around periodic wake-up operation and use the manufacturer’s low-power modes to reduce energy consumption between samples.

🏭

Compact Industrial Monitoring Controller

The STM32L031G6U6 is appropriate for small industrial monitoring modules that combine local sensing, status reporting, and simple control functions. Its 32-bit Arm Cortex-M0+ core runs at up to 32 MHz, giving adequate performance for peripheral management and event-driven logic without the complexity of a higher-tier processor. The 32 KB Flash, 8 KB RAM, and 1 KB EEPROM support embedded firmware, working buffers, and persistent configuration. The 4 x 4 mm UFQFPN package preserves PCB area, although designers should preserve the exposed-pad land and thermal copper path specified by the manufacturer.

📱

Low-Power Home Automation Endpoint

The STM32L031G6U6 can serve as the controller for a compact home-automation endpoint that measures environmental conditions or reacts to user inputs. Its Cortex-M0+ architecture handles timers, serial communication, and basic control logic, while the STM32L0 family’s low-power focus supports designs that remain idle for extended periods. The 32 KB Flash and 8 KB RAM are suitable for protocol handlers and small application state machines. A production board should use the exact manufacturer pin assignments because communication, wake, and debug functions must remain available while unused pins and the exposed pad are handled correctly.

🖥️

Portable Measurement Instrument

The STM32L031G6U6 suits portable instruments in which measurement control, display updates, and user interaction must coexist with a compact footprint. The 32 MHz Cortex-M0+ core can execute acquisition sequencing, calibration logic, and UI updates, while 8 KB of RAM provides space for buffers and 32 KB of Flash supports application firmware. Its small 28-pin UFQFPN package is valuable in handheld products where board area and energy use are constrained. Designers should verify the required analog, timer, and communication resources in the STM32L031G6 datasheet before assigning functions to pins.

🔧

Compact Accessory Controller

The STM32L031G6U6 is effective in compact accessories requiring a small embedded controller, such as configurable control modules, compact interface units, and low-energy peripheral controllers. Its 32-bit Cortex-M0+ architecture provides deterministic control execution at up to 32 MHz, while the 32 KB Flash and 8 KB RAM cover typical protocol and state-management workloads. The 28-pin UFQFPN package enables dense layouts but demands careful land-pattern execution and exposed-pad handling. Firmware should use the manufacturer’s startup and low-power guidance to avoid adding idle current through peripherals or I/O states.

💡

Smart Lighting Control Module

The STM32L031G6U6 can implement a compact smart-lighting controller that coordinates user inputs, schedules, status feedback, and communication traffic. The 32 MHz Cortex-M0+ core is sufficient for real-time switching logic and peripheral servicing, while the 8 KB RAM and 32 KB Flash support lightweight control firmware and local configuration. Its small UFQFPN footprint is useful in integrated lighting products where space is restricted. The controller should be evaluated for the required timing accuracy, output-driver interface, standby behavior, and automotive qualification needs of the finished product rather than for MCU performance alone.

Tóm tắt các sản phẩm được đề xuất

STM32L031G6 Family device used for firmware and peripheral planning Được sử dụng trong: Battery-Powered Sensor Node, Compact Industrial Monitoring Controller, Low-Power Home Automation Endpoint, Portable Measurement Instrument, Compact Accessory Controller, Smart Lighting Control Module STM32L031G6U6STR Related orderable configuration of the same family Được sử dụng trong: Battery-Powered Sensor Node, Low-Power Home Automation Endpoint, Compact Accessory Controller STM32F042G6U6 STMicroelectronics Được sử dụng trong: Compact Industrial Monitoring Controller, Portable Measurement Instrument, Smart Lighting Control Module
What are the key specifications of STM32L031G6U6 that engineers should know?
The STM32L031G6U6 is a 32 MHz Arm Cortex-M0+ microcontroller with 32 KB of Flash, 8 KB of RAM, and 1 KB of EEPROM in a 28-pin UFQFPN package. According to the STMicroelectronics STM32L031G6 datasheet, the device belongs to the ultra-low-power STM32L0 access line and combines a 32-bit RISC core with an extensive set of I/O and peripherals. These figures define its principal suitability for compact, energy-conscious embedded products.
Where can I download the STM32L031G6U6 datasheet PDF?
The official STM32L031G6U6 datasheet PDF is available from the manufacturer at https://www.st.com/resource/en/datasheet/stm32l031g6.pdf. The document is titled for the STM32L031G6 family and covers the Cortex-M0+ processor, embedded memory, electrical characteristics, package information, and peripheral behavior. Use the family document together with the exact UFQFPN ordering information for the STM32L031G6U6.
Where can I find the STM32L031G6U6 pinout?
The STM32L031G6U6 pinout is defined in the pin-description and package diagrams of the manufacturer’s STM32L031G6 family datasheet. The device uses a 28-pin UFQFPN package, so do not assume a generic QFN pinout. Use the manufacturer land pattern and pin-definition table when assigning PCB tracks, and observe the exposed-pad requirements shown in the package drawing.
What is the difference between STM32L031G6U6 and STM32L031G6U6STR?
STM32L031G6U6 and STM32L031G6U6STR identify different orderable configurations of the STM32L031G6U6 device family rather than different processor architectures. The listed device information identifies both as Cortex-M0+ MCUs with 32 MHz operation, 32 KB of Flash, and a 28-pin UFQFPN package. Confirm the exact packing and tape-and-reel suffix on the order before treating either part as a procurement substitution.
Is STM32L031G6U6 suitable for battery-powered sensor nodes?
The STM32L031G6U6 is suitable for battery-powered sensor nodes because it belongs to STMicroelectronics’ ultra-low-power STM32L0 access line. Its Cortex-M0+ core operates at up to 32 MHz, while the family supports low-energy operating modes for designs that spend substantial time idle. Actual battery life still depends on the sensor duty cycle, wake sources, regulator efficiency, and firmware behavior.
What memory does the STM32L031G6U6 contain?
The STM32L031G6U6 contains 32 KB of Flash program memory organized as 32K x 8, along with 8 KB of RAM and 1 KB of EEPROM. The STMicroelectronics STM32L031G6 datasheet identifies these as the embedded memory resources of the STM32L031x4/6 family. The combination is suitable for moderate firmware images, configuration data, and compact real-time control workloads.
How does STM32L031G6U6 compare with STM32F042G6U6 for a new design?
The STM32F042G6U6 is the closer same-package alternative identified for this design, but replacement should not be treated as automatic. Both are 32-bit Arm Cortex-M0+ microcontrollers associated with a 28-pin UFQFPN footprint, yet low-power behavior, peripherals, memory configuration, clock architecture, and firmware support can differ. Revalidate the full pin table, peripheral allocation, clock tree, and application firmware before production substitution.
When should I choose STM32L031G6U6 over STM32F042G6U6?
Choose STM32L031G6U6 when an ultra-low-power STM32L0 implementation and the established STM32L031G6 peripheral set are priorities. Choose STM32F042G6U6 only after checking whether its different memory or peripheral configuration satisfies the design. Both can share the 28-pin UFQFPN format, but physical package similarity does not eliminate software, peripheral, and pin-function compatibility checks.
What is the best drop-in replacement for STM32L031G6U6?
STM32F042G6U6 is the strongest candidate in the retrieved cross-reference material because it uses the same 28-pin UFQFPN format and a comparable Arm Cortex-M0+ architecture. It is a conditional drop-in candidate rather than an unconditional replacement because peripheral mappings and low-power characteristics require verification. A production swap should follow a complete GPIO, timer, communication, clock, debug, and firmware compatibility review.
Can STM32L031G6U6 be replaced without changing the PCB?
A no-PCB-change replacement is possible only when a candidate has the same 28-pin UFQFPN land pattern and pin functions. STM32F042G6U6 has the required package format, but its electrical and peripheral behavior must be checked against the installed design. Verify alternate-function assignments and application-specific pins rather than treating package equality as proof of complete replacement equivalence.
Where can I buy STM32L031G6U6 online?
Use the Request a Quote form on this page to request STM32L031G6U6 pricing, stock confirmation, and current lead time. The part is listed by STMicroelectronics as an STM32L031G6-family microcontroller in a 28-UFQFPN package, and multiple sourcing records exist. A formal quote is the appropriate route for obtaining an exact-MPN commercial commitment without relying on stale listing information.
What is the current price of STM32L031G6U6?
The current commercial price for STM32L031G6U6 should be obtained through the Request a Quote form on this page. Quote requests confirm the exact MPN, quantity, authorized supply condition, and current lead time. The structured pricing data on this page is intended for the platform’s live quotation process rather than a static customer-facing price guarantee.
What is the lead time and stock status for STM32L031G6U6?
Request current stock, minimum order quantity, and lead time for STM32L031G6U6 through the Request a Quote form on this page. Distributor status can vary by region, quantity, and supply condition, so a listing headline does not guarantee material for a production build. Include your requested quantity and target delivery date in the quote request.
Is STM32L031G6U6 the same as STM32L071K8U6?
No. STM32L071K8U6 is a different STM32L0 family device and is listed with a larger K-package configuration, while STM32L031G6U6 is an STM32L031G6U6 with a 28-UFQFPN package. It is therefore not a footprint-identical replacement for a completed STM32L031G6U6 board. Use it only for a new design after comparing memory, pin count, GPIO, peripherals, and software support.
What programming tools and firmware considerations apply to STM32L031G6U6?
The STM32L031G6U6 uses an Arm Cortex-M0+ architecture and is supported by the STMicroelectronics STM32 programming and software ecosystem. Firmware decisions should account for its 32 KB Flash, 8 KB RAM, 1 KB EEPROM, interrupt structure, and peripheral configuration. Confirm pin multiplexing and peripheral availability against the manufacturer’s CubeMX-generated configuration and the family reference manual.
What compliance and environmental specifications apply to STM32L031G6U6?
The STM32L031G6U6 is specified for operation from -40 °C to +85 °C, as stated in the product listing. RoHS, REACH, halogen-free, conflict-minerals, and AEC-Q100 status must be confirmed for the exact orderable configuration through STMicroelectronics’ product documentation or declarations. No automotive qualification should be assumed solely because the device operates across an industrial temperature range.

Dữ liệu tham khảo kỹ thuật cho STM32L031G6U6 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.

Hướng dẫn chọn lựa

Choose the STM32L031G6U6 when a new design benefits from the STM32L0 access line’s ultra-low-power positioning, a 32 MHz Cortex-M0+ core, 32 KB of Flash, 8 KB of RAM, and a compact 28-pin UFQFPN footprint. It is especially appropriate for battery-powered sensors, compact monitoring modules, and accessories that spend substantial time in low-energy states. STM32F042G6U6 is the practical candidate for a same-package design review because it retains the 28-UFQFPN format and similar memory organization, but its 48 MHz maximum clock and different STM32F0 peripheral architecture require explicit firmware and pin-function validation. Do not substitute it solely because the packages match. For designs requiring more flash, RAM, pins, or different peripherals, treat either MCU as a platform decision rather than a transparent component swap and compare the complete datasheet, package drawing, and application requirements.

So sánh với các sản phẩm thay thế

Tham số Sản phẩm này STM32F042G6U6
Brand STMicroelectronics STMicroelectronics
Package 28-UFQFPN (4x4) 28-UFQFPN (4x4)
Processor Core Arm Cortex-M0+ Arm Cortex-M0+
Maximum CPU Frequency 32 MHz 48 MHz
Flash Memory 32 KB 32 KB
RAM 8 KB 8 KB
EEPROM 1 KB 1 KB
Product Series STM32L0 access line STM32F0
Operating Temperature Range -40 °C to +85 °C -40 °C to +85 °C
Low-Power Focus Ultra-low-power STM32L0 access line STM32F0 general-purpose family
Pin Count 28 pins 28 pins
Price Tier Request a quote Request a quote

Bảo phân biệt quan trọng

  • Lower maximum clock frequency supports a more conservative processing target (vsSTM32F042G6U6)
  • Specialized ultra-low-power product positioning (vsSTM32F042G6U6)
  • Matches the established STM32L031G6 family memory architecture (vsSTM32F042G6U6)

Ghi chú thiết kế

Use the exact STM32L031G6U6 UFQFPN land pattern, including its exposed thermal pad, rather than a generic 28-pin QFN footprint. Confirm pad dimensions, pin numbering, solder-mask clearance, and paste stencil design against the manufacturer package drawing. The target uses a compact 4 x 4 mm package, so routing escape from inner rows and thermal-via placement require particular care.

Place the required local bypass capacitance directly beside the device power pins and keep the return-current path continuous through the exposed-pad land. Avoid routing sensitive signals beneath the MCU’s switching supply and high-current output paths. Select external components for the voltage range, startup behavior, and low-power current budget of the completed design after checking the family datasheet.

Do not treat the 28-UFQFPN package match between STM32L031G6U6 and STM32F042G6U6 as proof of complete interchangeability. Check every used GPIO, alternate function, timer channel, communication peripheral, clock pin, debug pin, and exposed-pad connection. Firmware, startup code, interrupt vectors, and low-power settings may also require revision when changing device families.

Keep clock, debug-programming, and communication routes short and away from noisy switching nodes. If the board supports external communication or sensor signals, route them over a continuous ground reference and follow the manufacturer’s recommended input filtering. Confirm that unused pins are left in states that do not increase leakage or prevent the intended low-power state.

Thông tin tuân thủ

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Không chì
Unknown
Không halogen
Unknown
Khoáng vật xung đột
Unknown

The operating temperature range is -40 °C to +85 °C. RoHS, REACH, halogen-free, lead-free, and conflict-minerals status require confirmation for the exact orderable device.

Dữ liệu được xác minh vào: 2026-11-19 — dữ liệu được xác minh và quản lý bởi đội ngũ kỹ thuật phần cứng của XAIPART

Tìm kiếm liên quan

stm32l031g6u6 datasheet stm32l031g6u6 pinout STM32L031G6U6 specifications STM32L031G6U6 datasheet PDF STM32L031G6U6 32MHz Cortex-M0+ STM32L031G6U6 32KB Flash 8KB RAM STM32L031G6U6 UFQFPN footprint STM32L031G6U6 equivalent STM32L031G6U6 replacement STM32L031G6U6 vs STM32F042G6U6 STM32L031G6U6 application circuit STM32L031G6U6 price STM32L031G6U6 stock STMicroelectronics STM32L031G6U6

Các bộ phận và thuật ngữ liên quan

STMicroelectronics STM32L031G6U6 STM32L031G6 STM32L031G6U6STR STM32F042G6U6 Arm Arm Cortex-M0+ 32-bit RISC microcontroller embedded controller ultra-low-power MCU STM32L0 access line STM32F0 Flash memory SRAM EEPROM 28-pin UFQFPN QFN package family surface mount 4 x 4 mm package battery-powered sensor node industrial monitoring home automation low-power mode 32 MHz
Báo giá nhanh RFQ
Hãy điền đầy đủ thông tin — đội ngũ bán hàng của chúng tôi sẽ phản hồi trong vòng 24 giờ
Mã sản phẩm Nhà sản xuất Kiểu đóng gói QTY Giá mục tiêu Phụ
✓
Báo giá đã gửi!

Chúng tôi sẽ trả lời email của bạn trong vòng 24 giờ

1
RFQ đã gửi
2
Phiếu báo giá nhận được
3
Đặt hàng thành công
4
Thanh toán
5
Đã gửi
6
Đã giao hàng
Xem chi tiết RFQ