SY88927VKC - 2.5Gbps Differential Receiver | Microchip
MPN: SY88927VKC ✓ Hoạt độngSY88927VKC Tóm tắt
A high-speed differential receiver converts a complementary differential input into a single-ended logic output. In the signal-chain hierarchy, this device belongs to the receiver and transceiver class of interface ICs, which sits between the physical data link and the digital logic that consumes the recovered signal. Differential reception helps reject common-mode noise, while the short package and low-voltage operation suit compact, high-speed backplane, clock, and data-conversion systems.
Key features include 2.5 Gb/s operation, a 3.0 GHz maximum frequency, internal 75K input pull-down resistors, and the ability to operate from either 3.3 V or 5 V. The output circuitry is ECL-compatible, and the manufacturer describes improved output waveform characteristics compared with earlier EL16V devices. These characteristics make the receiver useful where data must be restored cleanly at the end of a high-speed transmission path.
The SY88927V family is designed for high-frequency sources rather than low-speed general-purpose serial links. Its receiver architecture is intended to minimize signal degradation between a transmitting device and the receiving logic. Because the part has no transmitter, the board must provide a separate differential source, such as a clock generator, serializer, FPGA output, or other high-speed transceiver.
Typical applications include 2.5 Gb/s backplanes and point-to-point links, high-speed clock distribution interfaces, parallel-to-serial conversion systems, FPGA peripheral interfaces, and instrumentation that transfers high-frequency differential data. In these systems, controlled trace geometry, short connections, and proper termination are important because the usable performance depends on the complete source, transmission path, and receiving logic.
When laying out a circuit, route the differential pair as a tightly coupled impedance-controlled pair and place the receiver close to the data source when practical. Follow the manufacturer pin and application guidance for bypass capacitors and unused input states. Confirm the interface voltage levels, termination method, and input polarity before committing the layout because the receiver output is designed around ECL-compatible signaling rather than generic CMOS levels.
This page organizes the verified electrical ratings, package details, sourcing information, and engineering guidance for the SY88927VKC. It also identifies where replacement analysis requires additional manufacturer or distributor cross-reference information rather than treating electrically similar but mechanically different receivers as drop-in parts.
Bộ thay thế dễ dàng lắp đặt cho SY88927VKC — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Không có bộ thay thế dễ dàng lắp đặt sẵn có cho sản phẩm này.
Yêu cầu các bộ thay thếSY88927VKC Thông số kỹ thuật
| Device Type | High-speed differential receiver |
| Number of Receivers | 1 |
| Maximum Data Rate | 2.5 Gb/s |
| Maximum Frequency | 3.0 GHz |
| Supply Voltage Range | 3 V to 5.5 V |
| Supported Supply Options | 3.3 V or 5 V |
| I/O Logic Compatibility | 100K ECL-compatible |
| Internal Input Pull-Down Resistance | 75 kOhm |
| Hộp | 8-MSOP |
| Package Width | 3.00 mm |
| Kiểu lắp đặt | Surface mount |
| Output Waveform | Improved output waveform characteristics |
Hướng dẫn cấu hình chân SY88927VKC 3.00 mm
Cấu hình chân cho SY88927VKC (3.00 mm gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho SY88927VKC.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
SY88927VKC phù hợp cho 6 Áp dụngs: 2.5 Gb/s Backplane Interfaces, High-Speed Clock Distribution, FPGA High-Speed Data Capture, Parallel-to-Serial Conversion Links, Test and Measurement Instrumentation, Industrial Data-Link Backplanes.
2.5 Gb/s Backplane Interfaces
The SY88927VKC suits the receiving end of a 2.5 Gb/s point-to-point backplane link where a compact differential receiver is required. Its 2.5 Gb/s data rate and 3.0 GHz maximum frequency support high-edge-rate clock and data paths, while the single-receiver architecture leaves the transmit function to another device. Place the 8-MSOP close to the link endpoint and route the pair as a coupled, impedance-controlled net to limit loss and reflections.
High-Speed Clock Distribution
The receiver can terminate a high-frequency differential clock at the destination of a board-level distribution network. The 3.0 GHz maximum frequency and 100K ECL-compatible output provide a path for clocks well above the baseband data rate, while the internal 75 kOhm pull-down resistors define a defined state for open input conditions. Confirm clock amplitude, polarity, and output loading against the system timing budget before using the part.
FPGA High-Speed Data Capture
An FPGA or other high-speed digital engine can use the SY88927VKC as the receiving element of an external differential interface. The receiver converts a high-speed complementary input into a single-ended logic signal for downstream digital processing, reducing the burden on directly driving FPGA inputs with a remote source. The short 3 mm-wide MSOP helps minimize placement distance, but source impedance, termination, and trace geometry remain decisive.
Parallel-to-Serial Conversion Links
The SY88927VKC can receive the output of a high-speed serializer or parallel-to-serial conversion stage. Its receiver-only design is useful when transmit and receive functions are divided between separate ICs on the same board. At a 2.5 Gb/s operating rate, keep the receiver input path short and observe the manufacturer's input-state and bias guidance so that source, package, and board effects do not degrade the transition rate.
Test and Measurement Instrumentation
High-speed instrumentation can use the SY88927VKC to recover a differential signal generated by a remote test head, clock source, or acquisition channel. The part combines a 2.5 Gb-rated receiver with a small 8-MSOP footprint, which supports compact front-end placement near the connector or active probe circuitry. Because the output is ECL-compatible rather than a general CMOS interface, level translation may be required before a conventional test-controller input.
Industrial Data-Link Backplanes
Industrial backplane designs can use the SY88927VKC when a 2.5 Gb/s differential link must terminate in a compact receiver. The 3 V to 5.5 V supply range supports common industrial logic rails, and the receiver provides a defined input condition through 75 kOhm internal pull-downs. Verify the industrial temperature requirement against the specific ordering code and datasheet ratings before releasing the equipment for extended ambient operation.
Dữ liệu tham khảo kỹ thuật cho SY88927VKC — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này |
|---|---|
| Package | 8-MSOP, 3.00 mm wide |
| Brand | Microchip Technology |
| Device Type | High-speed differential receiver |
| Number of Drivers | 0 |
| Number of Receivers | 1 |
| Maximum Data Rate | 2.5 Gb/s |
| Supply Voltage Range | 3 V to 5.5 V |
| Maximum Frequency | 3.0 GHz |
| Internal Input Pull-Down Resistance | 75 kOhm |
| I/O Logic Compatibility | 100K ECL-compatible |
Bảo phân biệt quan trọng
- Receiver optimized for a 2.5 Gb/s data rate (vsGeneric low-speed single-ended receiver)
- Compact 8-MSOP implementation (vsLarger SOIC or multi-pin receiver package)
- Dual low-voltage supply flexibility (vsSingle-supply legacy ECL receiver)
Ghi chú thiết kế
Route the differential input as a short, tightly coupled pair on a controlled-impedance board. Keep the receiver away from noisy clock, switching-power, and high-current return paths. Differential routing is effective only when the pair maintains consistent geometry and termination; excessive skew can shift duty cycle even when the nominal data rate remains within specification.
Follow the manufacturer connection and decoupling guidance for the 3 V to 5.5 V supply, including the treatment of bias and supply pins. Place bypass capacitors close to their associated device pins with short ground returns. The limited current capability of the bias node called out in the datasheet means that it should not be used as a general-purpose supply rail.
Confirm source amplitude, differential input sensitivity, and ECL-compatible output levels with the other devices on the link. Internal 75 kOhm pull-down resistors establish a default input condition, but they are not a substitute for deliberate source termination. Validate eye margin and timing at the intended data rate because the receiver specification alone does not describe total channel loss.
Do not treat the SY88927VKC as a complete transceiver: it contains one receiver and no driver. Avoid substituting it for a CMOS receiver unless thresholds, output levels, biasing, and pin functions are verified. Also avoid confusing an EL16V-family functional relationship with guaranteed pin-to-pin interchangeability, since each ordering code requires datasheet-level confirmation.
Thông tin tuân thủ
The product listings and manufacturer datasheet do not state the requested environmental or conflict-minerals declarations. AEC-Q100 qualification is not applicable to this general-purpose interface IC.