Microchip Technology

SY88927VKC - 2.5Gbps Differential Receiver | Microchip

MPN: SY88927VKC ✓ פעיל
3 V to 5.5 V Vdss 75 kOhm Rds(on) 8-MSOP Package 3.0 GHz Speed
כמות הזמנה מינימלית: 1 |

SY88927VKC סקירה

The Microchip SY88927VKC is a high-speed differential receiver designed for 2.5 Gb/s data rates and operation from a 3.3 V or 5 V supply. The device is offered in an 8-pin MSOP package measuring 3 mm wide and is identified as a 0-driver, 1-receiver interface IC. According to the manufacturer datasheet, the receiver supports frequencies up to 3.0 GHz and uses 100K ECL-compatible I/O.

A high-speed differential receiver converts a complementary differential input into a single-ended logic output. In the signal-chain hierarchy, this device belongs to the receiver and transceiver class of interface ICs, which sits between the physical data link and the digital logic that consumes the recovered signal. Differential reception helps reject common-mode noise, while the short package and low-voltage operation suit compact, high-speed backplane, clock, and data-conversion systems.

Key features include 2.5 Gb/s operation, a 3.0 GHz maximum frequency, internal 75K input pull-down resistors, and the ability to operate from either 3.3 V or 5 V. The output circuitry is ECL-compatible, and the manufacturer describes improved output waveform characteristics compared with earlier EL16V devices. These characteristics make the receiver useful where data must be restored cleanly at the end of a high-speed transmission path.

The SY88927V family is designed for high-frequency sources rather than low-speed general-purpose serial links. Its receiver architecture is intended to minimize signal degradation between a transmitting device and the receiving logic. Because the part has no transmitter, the board must provide a separate differential source, such as a clock generator, serializer, FPGA output, or other high-speed transceiver.

Typical applications include 2.5 Gb/s backplanes and point-to-point links, high-speed clock distribution interfaces, parallel-to-serial conversion systems, FPGA peripheral interfaces, and instrumentation that transfers high-frequency differential data. In these systems, controlled trace geometry, short connections, and proper termination are important because the usable performance depends on the complete source, transmission path, and receiving logic.

When laying out a circuit, route the differential pair as a tightly coupled impedance-controlled pair and place the receiver close to the data source when practical. Follow the manufacturer pin and application guidance for bypass capacitors and unused input states. Confirm the interface voltage levels, termination method, and input polarity before committing the layout because the receiver output is designed around ECL-compatible signaling rather than generic CMOS levels.

This page organizes the verified electrical ratings, package details, sourcing information, and engineering guidance for the SY88927VKC. It also identifies where replacement analysis requires additional manufacturer or distributor cross-reference information rather than treating electrically similar but mechanically different receivers as drop-in parts.

חלופות תחליף ישיר עבור SY88927VKC — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.

אין חלופות תואמות Drop-in עבור מוצר זה.

בקשת חלופות

SY88927VKC מפרטים

Device Type High-speed differential receiver
Number of Receivers 1
Maximum Data Rate 2.5 Gb/s
Maximum Frequency 3.0 GHz
Supply Voltage Range 3 V to 5.5 V
Supported Supply Options 3.3 V or 5 V
I/O Logic Compatibility 100K ECL-compatible
Internal Input Pull-Down Resistance 75 kOhm
מארז 8-MSOP
Package Width 3.00 mm
סוג הרכבה Surface mount
Output Waveform Improved output waveform characteristics

מדריך תצורת פינים של SY88927VKC 3.00 mm

תצורת פינים עבור SY88927VKC (מארזת 3.00 mm). מספרי פינים, פונקציות ותרשימי חיבורים מוגדרים ב-Datasheet של היצרן. יש לעיין בו לקבלת ה-footprint המדויק והנחיות הלחמה.

תרשים פינים של מארזת 3.00 mm עבור SY88927VKC

אין נתוני פריסת פינים מפורטים עבור SY88927VKC.

עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.

יישומים טיפוסיים

SY88927VKC מתאים עבור 6 יישוםs: 2.5 Gb/s Backplane Interfaces, High-Speed Clock Distribution, FPGA High-Speed Data Capture, Parallel-to-Serial Conversion Links, Test and Measurement Instrumentation, Industrial Data-Link Backplanes.

🌐

2.5 Gb/s Backplane Interfaces

The SY88927VKC suits the receiving end of a 2.5 Gb/s point-to-point backplane link where a compact differential receiver is required. Its 2.5 Gb/s data rate and 3.0 GHz maximum frequency support high-edge-rate clock and data paths, while the single-receiver architecture leaves the transmit function to another device. Place the 8-MSOP close to the link endpoint and route the pair as a coupled, impedance-controlled net to limit loss and reflections.

🖥️

High-Speed Clock Distribution

The receiver can terminate a high-frequency differential clock at the destination of a board-level distribution network. The 3.0 GHz maximum frequency and 100K ECL-compatible output provide a path for clocks well above the baseband data rate, while the internal 75 kOhm pull-down resistors define a defined state for open input conditions. Confirm clock amplitude, polarity, and output loading against the system timing budget before using the part.

🧩

FPGA High-Speed Data Capture

An FPGA or other high-speed digital engine can use the SY88927VKC as the receiving element of an external differential interface. The receiver converts a high-speed complementary input into a single-ended logic signal for downstream digital processing, reducing the burden on directly driving FPGA inputs with a remote source. The short 3 mm-wide MSOP helps minimize placement distance, but source impedance, termination, and trace geometry remain decisive.

⚡

Parallel-to-Serial Conversion Links

The SY88927VKC can receive the output of a high-speed serializer or parallel-to-serial conversion stage. Its receiver-only design is useful when transmit and receive functions are divided between separate ICs on the same board. At a 2.5 Gb/s operating rate, keep the receiver input path short and observe the manufacturer's input-state and bias guidance so that source, package, and board effects do not degrade the transition rate.

🔧

Test and Measurement Instrumentation

High-speed instrumentation can use the SY88927VKC to recover a differential signal generated by a remote test head, clock source, or acquisition channel. The part combines a 2.5 Gb-rated receiver with a small 8-MSOP footprint, which supports compact front-end placement near the connector or active probe circuitry. Because the output is ECL-compatible rather than a general CMOS interface, level translation may be required before a conventional test-controller input.

🏭

Industrial Data-Link Backplanes

Industrial backplane designs can use the SY88927VKC when a 2.5 Gb/s differential link must terminate in a compact receiver. The 3 V to 5.5 V supply range supports common industrial logic rails, and the receiver provides a defined input condition through 75 kOhm internal pull-downs. Verify the industrial temperature requirement against the specific ordering code and datasheet ratings before releasing the equipment for extended ambient operation.

What is the SY88927VKC?
The SY88927VKC is a 2.5 Gb/s high-speed differential receiver from Microchip Technology. It provides one receiver and no driver, supports a 3 V to 5.5 V supply range, and is packaged in an 8-MSOP. According to the manufacturer datasheet, the receiver is intended for high-frequency differential sources and uses 100K ECL-compatible I/O.
What is the maximum data rate of the SY88927VKC?
The SY88927VKC supports data rates up to 2.5 Gb/s and a maximum operating frequency of 3.0 GHz. These figures come from the manufacturer datasheet and the product listing data. The receiver does not include a transmitter, so the connected source must be capable of driving the differential input at the required edge rate.
What supply voltage does the SY88927VKC use?
The SY88927VKC operates from a 3 V to 5.5 V supply and supports both 3.3 V and 5 V operating options. The listed voltage range also covers common low-voltage digital rails. Use the manufacturer bypass-capacitor and power-connection guidance when placing the decoupling components.
Where can I download the SY88927VKC datasheet PDF?
The official SY88927V datasheet PDF is available on the Microchip document server at the datasheet link on this page. It contains the device description, electrical characteristics, pin information, and application guidance. The manufacturer document should be used for board layout and interface decisions because it is the controlling technical reference for the part.
What is the SY88927VKC pinout?
The SY88927VKC is an 8-MSOP device with differential receiver inputs, a logic output, supply connections, and bias or reference connections described in the manufacturer datasheet. Use the pin-description table in that datasheet when assigning PCB tracks and test points. Do not infer a generic ECL pin arrangement from another receiver family.
How do I choose a drop-in replacement for the SY88927VKC?
A valid drop-in replacement must match the 8-MSOP footprint, pin assignment, supply range, input thresholds, output logic levels, and maximum data rate. Start with the Microchip cross-reference search and manufacturer documentation, then confirm availability through the Request a Quote form on this page. A receiver with a similar data rate but different biasing or output levels is not automatically interchangeable.
Can a 2.5 Gb/s receiver replace the SY88927VKC?
A 2.5 Gb/s receiver can be considered only after its mechanical and electrical interfaces are verified. The required checks include the 8-MSOP footprint, pin-to-pin mapping, 3 V to 5.5 V supply operation, ECL-compatible output levels, input termination, and bias requirements. Matching the headline data rate alone does not establish drop-in compatibility.
Where can I buy the SY88927VKC?
Use the Request a Quote form on this page to request current availability, a quotation, and lead-time information for the SY88927VKC. Because this device is an older high-speed interface IC and a single-receiver 8-MSOP part, practical stock can vary by lot. Providing the required quantity and target date in the request allows procurement to confirm the appropriate supply route.
What is the price of the SY88927VKC?
The current customer price for the SY88927VKC is obtained through the Request a Quote form on this page. Quotations may depend on quantity, availability, delivery location, and sourcing route. Submit the required quantity and target date on the form to obtain the applicable price and lead time for this exact MPN.
What is the lead time for the SY88927VKC?
The current lead time for the SY88927VKC should be confirmed through the Request a Quote form on this page. Availability can vary with lot position and procurement volume, so a specific schedule requires a quote request that states the quantity and required delivery date. The form on this page is the appropriate route for a current commitment.
Is the SY88927VKC currently in stock?
Current inventory for the SY88927VKC is confirmed when a quotation is requested through the Request a Quote form on this page. The product listing identifies the part as orderable, but a live stock position can change after that listing is generated. Include your required quantity and target date so procurement can confirm an available lot and schedule.
When should I use the SY88927VKC instead of a CMOS receiver?
Use the SY88927VKC when the interface requires a 2.5 Gb/s differential receiver with 100K ECL-compatible output behavior and a 3.3 V or 5 V supply. A CMOS receiver may be simpler at lower rates, but it can require different input thresholds, termination, and output voltage levels. Confirm every interface parameter against the datasheet before selecting the receiver family.
What can replace the SY88927VKC?
The closest replacement must be an 8-MSOP differential receiver with the same pin functions and compatible supply, threshold, bias, and output specifications. The SY88927VKC is functionally positioned as an improved EL16V-type receiver, but family-level equivalence does not prove mechanical or electrical interchangeability. Use the manufacturer cross-reference tool, verify the datasheet, and request a quote through this page.
Is the SY88927VKC the same as an EL16V receiver?
The SY88927VKC is described as functionally equivalent to the EL16V device family while offering faster output transitions and improved waveform characteristics. That makes it suitable as an upgrade where the source, supply, pinout, and logic levels remain compatible. It should not be treated as a universal replacement without checking the alternative receiver's pinout and bias requirements.
What are the key specifications engineers should know about the SY88927VKC?
The essential SY88927VKC specifications are a 2.5 Gb/s maximum data rate, 3.0 GHz maximum frequency, 3 V to 5.5 V operating supply, 75 kOhm internal input pull-down resistors, and an 8-MSOP package. According to the manufacturer datasheet, the device also provides 100K ECL-compatible I/O. These parameters define its source, layout, and replacement requirements.
What applications suit the SY88927VKC?
The SY88927VKC suits high-speed differential links where the source operates near 2.5 Gb/s, including backplanes, clock interfaces, and high-frequency data-conversion systems. Because the IC contains only a receiver, the board also needs a compatible transmitter, clock generator, or FPGA output. Short coupled routing and manufacturer-recommended termination are central to preserving performance.

נתוני עזר הנדסיים עבור SY88927VKC — השוואה, הנחיות תכנון ומידע על תאימות.

מדריך בחירה

Choose the SY88927VKC when a board must receive a high-speed differential signal at rates up to 2.5 Gb/s and the surrounding logic can work with 100K ECL-compatible output levels. Its 8-MSOP footprint is useful for compact routing, and the 3 V to 5.5 V supply range covers common 3.3 V and 5 V rails. Do not select it merely because another receiver has a similar headline speed: verify pin assignment, bias requirements, input thresholds, output levels, and termination. The part includes no transmitter, so a separate serializer, clock generator, FPGA output, or other source is required. For an EL16V-style upgrade, confirm that the alternative device preserves the same 8-MSOP footprint and interface levels. Request a quote for the exact SY88927VKC when lifecycle continuity, lot traceability, and a current delivery commitment are priorities.

השוואה עם חלופות

פרמטר מוצר זה
Package 8-MSOP, 3.00 mm wide
Brand Microchip Technology
Device Type High-speed differential receiver
Number of Drivers 0
Number of Receivers 1
Maximum Data Rate 2.5 Gb/s
Supply Voltage Range 3 V to 5.5 V
Maximum Frequency 3.0 GHz
Internal Input Pull-Down Resistance 75 kOhm
I/O Logic Compatibility 100K ECL-compatible

מבדילים עיקריים

  • Receiver optimized for a 2.5 Gb/s data rate (לעומתGeneric low-speed single-ended receiver)
  • Compact 8-MSOP implementation (לעומתLarger SOIC or multi-pin receiver package)
  • Dual low-voltage supply flexibility (לעומתSingle-supply legacy ECL receiver)

הערות תכנון

Route the differential input as a short, tightly coupled pair on a controlled-impedance board. Keep the receiver away from noisy clock, switching-power, and high-current return paths. Differential routing is effective only when the pair maintains consistent geometry and termination; excessive skew can shift duty cycle even when the nominal data rate remains within specification.

Follow the manufacturer connection and decoupling guidance for the 3 V to 5.5 V supply, including the treatment of bias and supply pins. Place bypass capacitors close to their associated device pins with short ground returns. The limited current capability of the bias node called out in the datasheet means that it should not be used as a general-purpose supply rail.

Confirm source amplitude, differential input sensitivity, and ECL-compatible output levels with the other devices on the link. Internal 75 kOhm pull-down resistors establish a default input condition, but they are not a substitute for deliberate source termination. Validate eye margin and timing at the intended data rate because the receiver specification alone does not describe total channel loss.

Do not treat the SY88927VKC as a complete transceiver: it contains one receiver and no driver. Avoid substituting it for a CMOS receiver unless thresholds, output levels, biasing, and pin functions are verified. Also avoid confusing an EL16V-family functional relationship with guaranteed pin-to-pin interchangeability, since each ordering code requires datasheet-level confirmation.

מידע על תאימות

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
נטול עופרת
Unknown
נטול הלוגנים
Unknown
מינרלים של סכסוך
Unknown

The product listings and manufacturer datasheet do not state the requested environmental or conflict-minerals declarations. AEC-Q100 qualification is not applicable to this general-purpose interface IC.

הנתונים אומתו בתאריך: 2026-11-16 — נתונים אומתו ונערכו על ידי צוות הנדסת הרכיבים של XAIPART

חיפושים קשורים

SY88927VKC datasheet SY88927VKC pinout SY88927VKC datasheet pdf SY88927VKC 8-MSOP receiver SY88927VKC 2.5Gb/s differential receiver Microchip SY88927VKC SY88927VKC equivalent SY88927VKC replacement SY88927VKC cross reference SY88927VKC footprint SY88927VKC spice model SY88927VKC price SY88927VKC stock SY88927VKC vs EL16V

רכיבים ומונחים קשורים

Microchip Technology Micrel Semiconductor SY88927VKC SY88927V SY88927VKC-TR SY100EL16V EL16V receiver family high-speed differential receiver differential receiver receiver IC transceiver interface IC ECL-compatible I/O 100K ECL 2.5 Gb/s 3.0 GHz 75 kOhm pull-down resistor 8-MSOP surface-mount package backplane interface FPGA interface clock distribution parallel-to-serial conversion RoHS REACH
בקשת הצעת מחיר מהירה
מלא את כל הפרטים — צוות המכירות שלנו יגיב תוך 24 שעות
מספר חלק יצרן מארז QTY מחיר יעד סה"כ
✓
הצעת המחיר נשלחה!

נשיב לדוא"ל שלך בתוך 24 שעות

1
בקשת הצעת מחיר נשלחה
2
הצעת מחיר התקבלה
3
ההזמנה בוצעה
4
תשלום
5
נשלח
6
נמסר
צפה בפרטי בקשת הצעת המחיר