SY89809LTC - 500 MHz 1:9 HSTL Clock Driver | Microchip
MPN: SY89809LTC ✗ Cuối đờiSY89809LTC Tóm tắt
A bus clock driver is a clock and timing integrated circuit that reproduces or buffers a clock signal while providing multiple outputs for system distribution. In the signal path, a clock buffer can increase fanout, isolate a source from downstream loading, and help maintain edge quality when driving multiple circuit groups. The SY89809LTC uses differential HSTL signaling, which supports robust high-speed transmission over controlled-impedance printed circuit board traces.
The key features of the SY89809LTC include a 1:9 fanout ratio, nine differential HSTL output pairs, a maximum operating frequency of 500 MHz, and compatibility with low-voltage 3.3 V and 1.8 V applications. The 32-pin TQFP package provides a surface-mount solution for compact systems requiring numerous clock outputs. The device is categorized as a clock fanout buffer and multiplexer with HSTL input and HSTL output.
Technically, the SY89809LTC is intended for high-performance bus-clock distribution rather than low-frequency general-purpose clock buffering. Differential clock distribution helps reduce sensitivity to common-mode noise on the PCB when trace impedance, pair spacing, and termination are controlled correctly. The 1:9 ratio allows one source clock to feed nine output pairs, reducing the number of separate buffering stages required in a multi-load clock tree.
Typical uses include processor clock distribution, memory-interface clock fanout, communications backplanes, test-and-measurement systems, and other high-speed digital platforms. In a processor or memory system, the device can distribute a central clock to several controller groups while limiting source loading. In communications equipment, the nine outputs can serve multiple modules or logical partitions, subject to the signal-integrity requirements of the complete board.
Design attention should be given to differential trace impedance, pair length matching, power-supply decoupling, and the electrical requirements of the connected HSTL devices. Place the device close to the clock source when the source has limited fanout capability, and route each differential pair as a controlled-impedance structure. Confirm the complete clock-tree topology and termination arrangement with the system-level timing and signal-integrity requirements.
This product page combines the manufacturer identification, package information, operating-frequency data, lifecycle information, application guidance, comparison fields, and verified source links for SY89809LTC. It is intended to help engineers establish the component identity, understand its clock-distribution role, and plan a qualified replacement or redesign review.
Bộ thay thế dễ dàng lắp đặt cho SY89809LTC — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Không có bộ thay thế dễ dàng lắp đặt sẵn có cho sản phẩm này.
Yêu cầu các bộ thay thếSY89809LTC Thông số kỹ thuật
| Device Type | Bus clock driver |
| Fanout Ratio | 1:9 |
| Number of Differential Output Pairs | 9 pairs |
| Maximum Operating Frequency | 500 MHz |
| Điện áp cung cấp | 3.3 V |
| Compatible Supply Voltage | 1.8 V or 3.3 V |
| Input Logic | HSTL |
| Output Logic | Differential HSTL |
| Number of Circuits | 1 circuit |
| Hộp | 32-pin TQFP, 7 mm x 7 mm |
| Kiểu lắp đặt | SMD (SMT) |
| Khoảng nhiệt độ hoạt động | 0°C to 85°C |
| Trạng thái vòng đời | Obsolete (EOL) |
| Input Clock Count | 1 input |
| Output Clock Count | 9 differential output pairs |
| Product Class | Clock fanout buffer, multiplexer |
Hướng dẫn cấu hình chân SY89809LTC 32-pin tqfp, 7 mm x 7 mm
Cấu hình chân cho SY89809LTC (32-pin tqfp, 7 mm x 7 mm gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho SY89809LTC.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
SY89809LTC phù hợp cho 6 Áp dụngs: Processor Clock Fanout, Memory Interface Clock Distribution, Communications Backplane Distribution, Test and Measurement Equipment, Industrial Control Data Backplane, High-Speed Digital Backplane Clocking.
Processor Clock Fanout
The SY89809LTC fits processor-clock trees that require one source signal to reach nine downstream logic groups. Its 1:9 fanout ratio can reduce the number of separate buffer stages, while the differential HSTL outputs support controlled-impedance routing at rates up to 500 MHz. Place the driver close to the source when source fanout is limited, and validate the clock topology against every receiver’s input capacitance and timing requirement. Because the device is obsolete, engineers should also review an approved lifecycle migration before committing it to a new platform.
Được đề xuất
Memory Interface Clock Distribution
The nine differential HSTL output pairs make the SY89809LTC applicable to memory-oriented systems that distribute a central clock among several controller or interface groups. Operation up to 500 MHz provides a useful design ceiling for many synchronous memory and backplane applications, while the 1:9 ratio simplifies fanout. The implementation must use differential routing with the required HSTL reference and termination arrangement. Confirm receiver loading, clock duty-cycle distortion, skew, and board-level timing margins before release.
Được đề xuất
Communications Backplane Distribution
The SY89809LTC can distribute a common bus clock across multiple communications modules when the system uses HSTL and requires nine differential branches. Differential signaling helps maintain signal integrity over controlled-impedance PCB traces, and the 500 MHz maximum operating frequency supports high-speed digital architectures. Route output pairs away from noisy sources, maintain consistent pair geometry, and include the correct reference-plane transitions. Any change to the clock source, receiver standard, cable, or connector requires a new signal-integrity review.
Được đề xuất
Test and Measurement Equipment
The SY89809LTC is appropriate for test and measurement equipment that must fan one high-speed clock across multiple acquisition, control, or conversion sections. Its nine differential HSTL outputs can reduce clock-tree complexity and support distribution up to 500 MHz. Designers should evaluate deterministic and random jitter, duty-cycle distortion, output-to-output skew, return loss, and channel loss rather than relying only on the headline frequency. Use controlled-impedance routing and keep sensitive analog or timing circuitry outside noisy clock-return paths.
Được đề xuất
Industrial Control Data Backplane
In an industrial controller, the SY89809LTC can provide a common differential clock to several data-processing or communication blocks. The 1:9 ratio is useful when a backplane includes multiple bus-clock destinations, and the surface-mount 32-pin TQFP supports compact controller assemblies. Industrial temperature and lifecycle requirements should be checked independently from the stated 0°C to 85°C operating range. Because the component is obsolete, production continuation should depend on formal manufacturer guidance and a documented engineering change process.
Được đề xuất
High-Speed Digital Backplane Clocking
The SY89809LTC is suited to a high-speed digital backplane that requires nine differential HSTL clock branches from one central source. Its 500 MHz operating capability can support demanding synchronous routing while reducing clock-tree stage count. Correct use depends on preserving differential impedance, controlling pair skew, and terminating the HSTL network according to the system architecture. Validate source amplitude, receiver thresholds, loading, and worst-case cable or trace behavior before using the device as a drop-in design element in a new backplane.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho SY89809LTC — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này |
|---|---|
| Brand | Microchip Technology |
| Package | 32-pin TQFP, 7 mm x 7 mm |
| Device Type | Bus clock driver |
| Fanout Ratio | 1:9 |
| Differential Output Pairs | 9 pairs |
| Maximum Frequency | 500 MHz |
| Nominal Supply Voltage | 3.3 V |
| Input Logic | HSTL |
| Output Logic | Differential HSTL |
| Operating Temperature Range | 0°C to 85°C |
Bảo phân biệt quan trọng
- Provides nine differential clock branches from one source (vsNo verified drop-in alternative)
- Supports 500 MHz differential HSTL distribution (vsNo verified drop-in alternative)
- Combines nine outputs with a 32-pin TQFP footprint (vsNo verified drop-in alternative)
Ghi chú thiết kế
Route all nine differential HSTL output pairs as controlled-impedance traces with consistent pair spacing and a continuous reference plane. Match pair length where the system requires minimized skew between clock destinations. Avoid splitting a differential pair across package or board layers, and keep the clock-input route short enough to avoid unnecessary attenuation before the first output branch.
Validate the complete HSTL network at the target clock frequency, including source amplitude, receiver thresholds, trace loss, loading, and termination. A 500 MHz clock leaves less margin for impedance discontinuities and excessive loading than a low-frequency clock. Use the manufacturer application guidance and system-level signal-integrity model to establish termination locations and acceptable output skew.
Place power-supply decoupling components close to the device supply pins and connect them to an appropriate ground reference with minimal loop area. Maintain short, direct clock-input routing and avoid coupling the input net to output and data nets. Check power sequencing, supply ramp behavior, and clock startup conditions in hardware because a static schematic review does not establish safe operating behavior.
Do not treat any generic nine-output clock buffer as a direct replacement. The SY89809LTC is obsolete and uses a specific 32-pin TQFP arrangement with HSTL signaling. A valid migration requires matching pin assignments, supply voltage, input thresholds, output swing, reference-plane arrangement, frequency capability, and package dimensions, followed by board-level timing validation.
Thông tin tuân thủ
The component is a general-purpose clock and timing IC rather than an automotive-qualified device. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations require confirmation from the manufacturer.