THS4051ID - 70MHz High-Speed Amplifier | Texas Instruments
MPN: THS4051ID ✓ Hoạt độngTHS4051ID Tóm tắt
A high-speed voltage-feedback amplifier is a voltage-amplifier topology that uses feedback to set closed-loop gain while preserving signal fidelity across a wide frequency range. The THS4051 belongs to the operational-amplifier hierarchy, combining low-noise signal conditioning with the fast response required by video, communications, and imaging systems. Its stable operation at all gains makes it useful in gain-dependent analog front ends where predictable behavior is important.
The principal performance features are 70 MHz small-signal bandwidth, 240 V/µs slew rate, and 60 ns settling to 0.1%. The amplifier also provides 100 mA typical output drive and a 30 MHz differential-gain bandwidth of 0.1 dB. According to the Texas Instruments manufacturer datasheet, these characteristics make THS4051 suitable for video, communication, and imaging applications.
THS4051 uses a voltage-feedback architecture and is stable at all gains in both inverting and non-inverting configurations. Its bandwidth supports video signals extending to the 30 MHz region, while the 240 V/µs slew rate limits large-signal distortion when handling rapidly changing waveforms. The device operates from dual supplies of ±4.5 V to ±16 V, supporting conventional positive and negative analog rails used in professional video and communications equipment.
Typical uses include video buffering, communications-signal conditioning, imaging front ends, active filters, and general-purpose high-speed analog amplification. In these systems, the amplifier can reduce edge degradation that might otherwise appear when a slower amplifier drives a terminated or capacitive load. The single-channel configuration also lets designers allocate one amplifier per signal when channel count and board area are important.
When laying out a THS4051 circuit, use short feedback paths, place input and feedback components close to the pins, and minimize parasitic capacitance around high-impedance input nodes. Keep power-supply decoupling close to the supply pins and verify stability with the actual source impedance, load, and cable capacitance used in the finished system.
This product page consolidates the THS4051ID electrical characteristics, validated same-package alternatives, application guidance, comparison parameters, and practical PCB considerations. These engineering-oriented details help engineers select the amplifier, compare suitable replacements, and plan a robust high-speed analog layout without duplicating basic datasheet lookups.
Bộ thay thế dễ dàng lắp đặt cho THS4051ID — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
THS4051CDR
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
THS4051IDRG4
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
THS4051ID Tỷ lệ tối đa & tính chất điện
| Amplifier Type | Single-channel voltage-feedback high-speed amplifier |
| Number of Channels | 1 channel |
| Small-Signal Bandwidth | 70 MHz |
| Slew Rate | 240 V/µs |
| Settling Time | 60 ns to 0.1% |
| Output Drive | 100 mA typical |
| Differential Gain Bandwidth | 30 MHz at 0.1 dB |
| Differential Phase | 0.01° |
| Supply Voltage Range | ±4.5 V to ±16 V |
| Gain Stability | Stable at all gains in inverting and non-inverting configurations |
| Hộp | 8-SOIC, 0.154 inch (3.90 mm) body width |
| Số chân | 8 pins |
| Kiểu lắp đặt | Surface mount |
| Primary Applications | Video, communications, and imaging |
| Amplifier Topology | Voltage feedback |
Hướng dẫn cấu hình chân THS4051ID 8-soic, 0.154 inch (3.90 mm) body width
Cấu hình chân cho THS4051ID (8-soic, 0.154 inch (3.90 mm) body width gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho THS4051ID.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
THS4051ID phù hợp cho 6 Áp dụngs: Video Signal Buffering, Communications Signal Conditioning, Imaging Front-End Amplification, High-Speed Active Filters, Precision Edge and Pulse Conditioning, Analog Test and Measurement.
Video Signal Buffering
The THS4051ID fits video buffers because it combines 70 MHz small-signal bandwidth with a 240 V/µs slew rate, preserving edge definition in higher-bandwidth analog paths. Its 30 MHz differential-gain bandwidth at 0.1 dB is also well suited to video distribution and gain stages. Place the amplifier close to the source and load, use short traces, and terminate the output according to the video standard and cable length. Verify output swing, source impedance, and settling performance at the intended gain before finalizing the PCB.
Được đề xuất
Communications Signal Conditioning
THS4051ID is appropriate for communications signal-conditioning stages that need a 70 MHz bandwidth and rapid large-signal response. The 240 V/µs slew rate and 60 ns settling time help preserve pulse shape when source and load impedances create meaningful transition requirements. Use short, impedance-controlled routing and keep feedback components adjacent to the amplifier to minimize parasitic feedback. Confirm the complete data path against the required modulation bandwidth, output amplitude, and channel timing budget.
Được đề xuất
Imaging Front-End Amplification
The THS4051ID can support imaging front ends where sensor or photodiode signals require low-distortion amplification across a broad bandwidth. Its 240 V/µs slew rate improves large-signal response, while stable operation at all gains simplifies the selection of inverting or non-inverting signal paths. Keep sensitive input nodes short and shielded from switching nodes, and evaluate noise, input bias current, and photodiode capacitance against the sensor specification. The amplifier’s 8-SOIC format also supports compact board arrangements when channel density matters.
Được đề xuất
High-Speed Active Filters
THS4051ID is suitable for wide-band active-filter stages because it is stable at all gains and combines 70 MHz bandwidth with a 240 V/µs slew rate. These characteristics allow practical filter bandwidths beyond those of many general-purpose operational amplifiers. Select resistor and capacitor values against the closed-loop gain, then check filter Q, component tolerances, and op-amp noise in the complete circuit. High-Q stages need careful layout because parasitic capacitance and probe loading can shift the intended response.
Được đề xuất
Precision Edge and Pulse Conditioning
The THS4051ID supports pulse and edge conditioning where the 240 V/µs slew rate and 60 ns settling time are more important than the quiescent current of a lower-speed amplifier. Fast transitions reduce the duration of amplitude distortion and help maintain timing relationships between channels. Confirm that the signal amplitude remains inside the output swing limits at the selected supply voltage, and use matched layouts when multiple channels must preserve skew. Add resistive loading or output isolation if the next stage presents unexpected capacitive loading.
Được đề xuất
Analog Test and Measurement
The THS4051ID is appropriate for general-purpose high-speed analog test and measurement circuits that require 70 MHz bandwidth and rapid settling. It can serve as a buffer, gain stage, or output driver in equipment handling waveforms with meaningful edge content. The 8-SOIC package is straightforward to assemble, but precision measurements also require attention to offset, noise, probe loading, and connector parasitics. Evaluate those parameters with the actual fixture and bandwidth requirement rather than relying on small-signal bandwidth alone.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho THS4051ID — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | THS4051CDR | THS4051IDRG4 |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-SOIC | 8-SOIC - same | 8-SOIC - same |
| Channel Count | 1 channel | 1 channel | 1 channel |
| Small-Signal Bandwidth | 70 MHz | 70 MHz | 70 MHz |
| Slew Rate | 240 V/µs | 240 V/µs | 240 V/µs |
| Settling Time | 60 ns to 0.1% | 60 ns to 0.1% | 60 ns to 0.1% |
| Output Drive | 100 mA typical | 100 mA typical | 100 mA typical |
| Supply Voltage Range | ±4.5 V to ±16 V | ±4.5 V to ±16 V | ±4.5 V to ±16 V |
| Gain Stability | Stable at all gains in inverting and non-inverting configurations | Stable at all gains in inverting and non-inverting configurations | Stable at all gains in inverting and non-inverting configurations |
| Differential Gain Bandwidth | 30 MHz at 0.1 dB | 30 MHz at 0.1 dB | 30 MHz at 0.1 dB |
Bảo phân biệt quan trọng
- High-speed response with stable all-gain operation (vsTHS4051CDR)
- Direct same-package ordering option (vsTHS4051IDRG4)
- Single-channel architecture supports independent analog paths (vsTHS4031ID)
Ghi chú thiết kế
Route the high-speed signal path as a short, continuous trace from the source to the amplifier input and from the output to the load. Place input and feedback components directly beside their associated pins, and avoid routing sensitive input traces parallel to output and supply-return paths. For an 8-SOIC footprint, follow the Texas Instruments package drawing and PCB guidelines so pad spacing, solder mask, and assembly clearances match the specified body width.
Use a solid, low-impedance ground reference and place supply-bypass capacitors close to the amplifier supply pins. The 240 V/µs slew rate can produce fast current transitions, so long supply and ground loops increase radiated noise and may disturb neighboring analog stages. Keep the feedback loop compact and use a solid ground plane where possible. Verify the finished board with an oscilloscope because parasitic inductance and capacitance can affect settling even when the schematic simulation appears correct.
Do not select an amplifier from bandwidth alone when the application contains large signals or heavy capacitive loading. Although THS4051ID provides 70 MHz bandwidth and 240 V/µs slew rate, output swing, load current, supply headroom, and stability can impose earlier limits. Check the manufacturer operating conditions, use the intended load and source impedance, and preserve the supported common-mode range. Also confirm the exact physical pin map from the manufacturer datasheet before releasing artwork.
For cable or long-trace outputs, terminate the line according to its characteristic impedance and place any isolation resistor close to the amplifier pin. Rapid edges make uncontrolled impedance discontinuities more likely to produce reflections. If the source has significant capacitance, add a suitable isolation network and recheck stability and amplitude response. Probe with a short ground spring or a proper active probe to avoid adding unintended capacitance at the measurement point.
Thông tin tuân thủ
Use the current Texas Instruments product page and material-compliance documentation for formal RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations.
