THS6093IDR - 275mA +12V ADSL Line Driver | Texas Instruments (Tape & Reel)
MPN: THS6093IDR ✓ Hoạt độngTHS6093IDR Tóm tắt
An ADSL line driver is a specialized interface-circuit component that converts upstream driver signals into robust, high-current line outputs suitable for copper telephone networks. It sits within the power-management and signal-conditioning hierarchy of a customer premises equipment design, translating logic-level commands into line-side waveforms while helping preserve signal integrity across the transformer-coupled network.
Key features include a wide supply-voltage range, suitability for single +12 V operation, compatibility with a 1:2 transformer ratio, and low 2.1 pA/√Hz noninverting current noise. The THS6093 also provides low total harmonic distortion of -72 dBc while driving the line and includes shutdown control. Each channel draws only 7.3 mA of supply current, helping limit the power burden of a multi-output access circuit.
The device uses two noninverting outputs in a 14-pin SOIC package. Its high output-current capability is important for ADSL line interfaces because the external transformer, network loading, and cable losses can require substantially more current than a conventional logic driver. The specified 275 mA rating provides the core design limit for transformer selection, copper-line loading, supply capability, and thermal analysis.
Typical uses include full-rate ADSL customer premises equipment, G.Lite ADSL line interfaces, and power-line carrier line-driver circuits. In each application, the THS6093 can operate from a single +12 V rail and drive the line through an appropriate external transformer while the shutdown function provides a controlled path for reducing activity when the endpoint is inactive.
The primary design consideration is ensuring that the +12 V supply, output-current demand, transformer ratio, load, thermal conditions, and signal-integrity expectations all agree. Use the manufacturer datasheet pin-description table when assigning PCB nets, and confirm that the selected transformer supports the specified 1:2 ratio and operating bandwidth.
Bộ thay thế dễ dàng lắp đặt cho THS6093IDR — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
THS6093IDRG4
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
THS6093IDR Thông số kỹ thuật
| Product Type | Dual ADSL CPE and PLC line driver |
| Output Current | 275 mA |
| Nominal Supply Voltage | +12 V |
| Điện áp cung cấp | 7.3 mA per channel |
| Number of Driver Channels | 2 |
| Noninverting Current Noise | 2.1 pA/√Hz |
| Total Harmonic Distortion | -72 dBc while driving |
| Transformer Compatibility | 1:2 transformer ratio |
| Shutdown Function | Yes |
| Supported Applications | Full-rate ADSL, G.Lite ADSL, and PLC line driving |
| Hộp | 14-pin SOIC, 0.154 inch body width, 3.90 mm width |
| Kiểu lắp đặt | Surface mount |
| Packaging | Tube |
Hướng dẫn cấu hình chân THS6093IDR 14-pin soic, 0.154 inch body width, 3.90 mm width
Cấu hình chân cho THS6093IDR (14-pin soic, 0.154 inch body width, 3.90 mm width gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho THS6093IDR.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
THS6093IDR phù hợp cho 6 Áp dụngs: Full-Rate ADSL CPE Line Interface, G.Lite ADSL Terminal Interface, Power-Line Carrier Line Driver, Central Office Line-Side Interface, Remote Terminal Equipment Line Output, Copper Network Access Card.
Full-Rate ADSL CPE Line Interface
The THS6093IDR fits a full-rate ADSL customer premises equipment line driver because it provides two 275 mA-capable outputs, operates from a single +12 V supply, and supports the required 1:2 transformer ratio. Each channel consumes 7.3 mA of supply current, which helps control the power requirement of the dual-channel interface. Its specified 2.1 pA/√Hz noninverting current noise and -72 dBc distortion support waveform quality at the line driver stage. Place the device close to the external transformer and follow the manufacturer decoupling and routing guidance to limit supply disturbance and preserve high-speed signal integrity.
Được đề xuất
G.Lite ADSL Terminal Interface
The THS6093IDR is suitable for a G.Lite ADSL terminal interface where reduced-rate operation requires a robust copper-line output stage. The device supports full-rate ADSL and G.Lite applications and can use a single +12 V supply, avoiding the need for a split positive and negative line-driver rail. Its two-channel architecture allows a compact implementation when the design drives two related line outputs. The 275 mA output rating, 7.3 mA supply current per channel, and specified 2.1 pA/√Hz noise density make it possible to balance line-drive capability against board space and power use.
Được đề xuất
Power-Line Carrier Line Driver
The THS6093IDR can serve as a power-line carrier line driver because it combines a 275 mA output-current capability with low noninverting current noise of 2.1 pA/√Hz. The device supports a single +12 V operating rail and includes shutdown control, allowing the interface to be disabled when the communication channel is not required. Its -72 dBc total harmonic distortion specification is valuable when preserving waveform quality through the coupling network. The external coupling or transformer network remains application-specific, so validate its ratio, bandwidth, loading, and isolation against the manufacturer interface guidance.
Được đề xuất
Central Office Line-Side Interface
The THS6093IDR can be evaluated for a central-office line-side interface where compact, high-current driver capability is needed. Two channels in a 14-pin SOIC reduce board area compared with separate single-channel implementations, while 7.3 mA supply current per channel supports a practical multi-channel power budget. Its 275 mA output rating must be reconciled with the transformer, cable length, line impedance, and worst-case operating condition. Because shutdown and output behavior are central to line-interface management, use the manufacturer pin and application descriptions when defining the interface topology.
Được đề xuất
Remote Terminal Equipment Line Output
The THS6093IDR is appropriate for remote terminal equipment that drives a signal from the customer premises toward the central office. Its noninverting output arrangement simplifies the drive path for compatible line-interface circuitry, while the 1:2 transformer compatibility provides a defined starting point for network-coupling design. The 275 mA capability accommodates the current demanded by the line interface, but the actual operating point must include transformer losses and network loading. Shutdown control can reduce activity during inactive periods, while the low-noise and low-distortion characteristics support transmission quality.
Được đề xuất
Copper Network Access Card
A copper network access card can use the THS6093IDR when it requires two high-current line-driver outputs in a limited PCB area. The 14-pin SOIC package is compatible with conventional surface-mount assembly, and the dual-channel configuration consolidates related line-drive functions. Single +12 V operation simplifies the principal power rail, while 7.3 mA per channel provides a starting point for thermal and supply budgeting. The design must still reserve adequate routing and component placement for the external transformer, input/output return paths, and supply decoupling recommended for reliable high-speed line transmission.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho THS6093IDR — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | THS6093IDRRG4 |
|---|---|---|
| Package | 14-SOIC | 14-SOIC |
| Brand | Texas Instruments | Texas Instruments |
| Product Type | Dual ADSL CPE and PLC line driver | Same functional characteristics and terminals as THS6093IDR |
| Output Current | 275 mA | 275 mA consistent with THS6093IDR |
| Nominal Supply Voltage | +12 V | +12 V consistent with THS6093IDR |
| Driver Channels | 2 | 2 consistent with THS6093IDR |
| Supply Current | 7.3 mA per channel | 7.3 mA per channel consistent with THS6093IDR |
| Noninverting Current Noise | 2.1 pA/√Hz | 2.1 pA/√Hz consistent with THS6093IDR |
| Total Harmonic Distortion | -72 dBc while driving | -72 dBc while driving consistent with THS6093IDR |
| Transformer Ratio | Compatible with 1:2 | Compatible with 1:2 consistent with THS6093IDR |
Bảo phân biệt quan trọng
- Direct THS6093IDR replacement without PCB changes (vsTHS6093IDRRG4)
- High-current dual line-drive capability (vsTHS6093IDRRG4)
- Low-noise and low-distortion line output (vsTHS6093IDRRG4)
Ghi chú thiết kế
Design the +12 V supply around the combined requirements of both channels and the worst-case line load. Each channel draws 7.3 mA of supply current, but the external transformer and line network determine the switching and current demand at the outputs. Verify the 275 mA rating against actual load, pulse behavior, and temperature rather than treating it as a universal continuous-current allowance.
Use the manufacturer datasheet pin-description table when assigning the 14-SOIC footprint and follow its application layout for input, output, supply, ground, and shutdown routing. Keep the line-driver outputs and their associated return paths compact, and place decoupling and signal-conditioning components close to their relevant pins. Poor high-speed return-current paths can increase distortion even when the regulator and external transformer are correctly selected.
Do not select a generic high-current line driver solely by package size. The THS6093IDR's suitability depends on its 275 mA rating, 1:2 transformer compatibility, 2.1 pA/√Hz current noise, -72 dBc distortion while driving, and shutdown behavior. Check the exact ordering code and packaging format during production release to avoid mixing requirements between THS6093IDR and THS6093IDRRG4.
Estimated: the conductor dissipation is P = I² × R, using the actual output-current waveform and effective copper-network resistance. Apply the calculated dissipation to the relevant device and transformer thermal model, then apply the manufacturer ambient and junction-temperature limits. Because no exact thermal-resistance data are stated here, request those values from the datasheet before sizing copper area or specifying a thermal solution.
Thông tin tuân thủ
No explicit environmental or automotive qualification statements were identified for THS6093IDR.