TLE62512G - 1 Mbaud CAN Transceiver | Infineon | Automotive
MPN: TLE62512G ✗ Cuối đờiTLE62512G Tóm tắt
A CAN transceiver is an interface IC that converts logic-level signals between a host controller and the physical CAN bus. It belongs to the automotive communication-interface hierarchy: CAN controller interface, CAN transceiver, interface IC, and semiconductor. The transceiver handles bus-line signaling, while a separate CAN controller normally handles frame generation, arbitration, error management, and higher-level communication.
Key verified features of the TLE6251-2G family include 1 Mbaud operation, ISO 11898-5 compliance, wake functionality, failure detection, a low-power sleep mode, and ESD protection. These features target automotive and mixed-power-supply HS-CAN systems where low quiescent consumption and defined behavior during power-down are useful. The target is a single 1/1 CAN transceiver rather than a multi-channel CAN controller.
The DSO-14 package supports compact PCB integration, while the electrical interface is intended to connect the transceiver's TX, RX, CANH, and CANL-related system connections to an external bus network. Exact pin names, absolute maximum ratings, supply-voltage limits, loop-delay limits, propagation-delay values, and thermal limits must be taken from the manufacturer datasheet rather than inferred from distributor listings.
Typical applications include automotive ECUs, body-control modules, powertrain controllers, gateway electronics, industrial automation equipment using CAN, and mixed-power HS-CAN networks. In these systems, the transceiver provides the physical-layer interface while the controller manages protocol frames. Select the TLE62512G when the design specifically requires the verified Infineon 1 Mbaud CAN interface and its listed wake, failure-detection, sleep, ESD, and ISO 11898-5 features.
Before layout is finalized, verify the complete pinout, recommended external components, bus termination, supply sequencing, and transceiver operating modes in the manufacturer documentation. Do not substitute a similar CAN device without checking pin compatibility, bus timing, standby behavior, failure reporting, and package details.
Bộ thay thế dễ dàng lắp đặt cho TLE62512G — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với TLE62512G (cùng hình factor và footprint) — khác nhau ở Failure Detection, Package, Power-Down Behavior.
TLE62512GXUMA1
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →TLE62512GXUMA3
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
TLE62512GS
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
TLE6251-2G
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
TLE62512G
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →TLE62512G Thông số kỹ thuật
| Product Type | High-speed CAN transceiver |
| CAN Data Rate | 1 Mbaud |
| CAN Interface | 1/1 CAN transceiver |
| Compliance | ISO 11898-5 compliant |
| Wake Function | Wake capability |
| Failure Detection | Failure detection capability |
| Sleep Mode | Low-power sleep mode |
| ESD Protection | ESD protection |
| Power-Down Behavior | Excellent passive behavior in power-down |
| Hộp | DSO-14 |
| Package Type | Surface-mount DSO |
Hướng dẫn cấu hình chân TLE62512G surface-mount dso
Cấu hình chân cho TLE62512G (surface-mount dso gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho TLE62512G.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
TLE62512G phù hợp cho 6 Áp dụngs: Automotive Electronic Control Units, Vehicle Body-Control Modules, Industrial CAN Automation, CAN Gateway Modules, Mixed-Power-Supply HS-CAN Networks, Diagnostic and Test Equipment.
Automotive Electronic Control Units
The TLE62512G fits an automotive ECU that connects a CAN controller to a high-speed CAN bus. Its verified 1 Mbaud capability supports the physical layer used for body, comfort, gateway, and powertrain-related communication designs. The wake function helps a node react to bus activity, while failure detection gives the controller a diagnostic signal when the interface detects a bus-related problem. The DSO-14 package also keeps the physical interface compact. Before layout, confirm the exact pinout, external termination requirements, EMC layout, and supply values from the Infineon datasheet.
Được đề xuất
Vehicle Body-Control Modules
A body-control module can use the TLE62512G as the high-speed CAN physical interface for distributed vehicle functions such as centralized gateway communication, lighting control, door systems, and climate-control coordination. The 1 Mbaud rate and wake capability match the family’s intended HS-CAN use, while low-power sleep mode is valuable when the vehicle must reduce standby consumption. The interface does not replace the CAN protocol controller; it translates between controller I/O and CAN bus signaling. Verify transceiver timing, fault behavior, and all package pins before schematic release.
Được đề xuất
Industrial CAN Automation
The TLE62512G can serve as the CAN physical-layer device in industrial automation equipment that uses a CAN controller to connect sensors, drives, remote I/O, or service equipment. Its 1 Mbaud rate supports high-speed CAN communication, while wake and sleep functions can help manage inactive network periods. The interface should be placed according to the manufacturer’s bus-layout recommendations, with attention to termination, common-mode behavior, ESD protection, and grounding. Because industrial systems may use different bus lengths and fault conditions, verify the full electrical limits before selecting the device.
Được đề xuất
CAN Gateway Modules
A gateway module can use the TLE62512G as a single CAN transceiver interface when it needs a high-speed CAN physical connection alongside another communication or processing section. The family’s 1 Mbaud specification, wake capability, failure detection, and sleep operation are useful for gateways that may remain connected to a mixed-power HS-CAN network. The transceiver should be paired with a controller whose timing and termination expectations match the bus. Keep the CAN traces short and controlled, provide the specified bus protection and bypass components, and confirm that the exact DSO-14 variant is used.
Được đề xuất
Mixed-Power-Supply HS-CAN Networks
The TLE62512G is specifically associated by Infineon documentation with mixed-power-supply high-speed CAN networks. The family listing highlights excellent passive behavior during power-down, which helps a node avoid inappropriate bus activity while its local supply is transitioning or unavailable. That behavior is important when different portions of a vehicle or industrial system use separate supply domains. The design still requires correct enable/standby sequencing, bus termination, supply decoupling, and EMC layout. Confirm the exact operating-mode truth table and power-down electrical limits in the manufacturer documentation.
Được đề xuất
Diagnostic and Test Equipment
The TLE62512G can be used in CAN diagnostic equipment or test fixtures that need a deterministic physical interface to a high-speed CAN network. The 1 Mbaud rate supports standard HS-CAN test traffic, while wake and failure detection help the fixture exercise low-power and error-related operating conditions. The device is only the physical interface, so the test system also needs a CAN controller, bus termination, instrumentation, and software that generates and validates frames. Use isolated test arrangements when the target network can have ground-potential differences.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho TLE62512G — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | TLE62512GXUMA1 | TLE62512GXUMA3 | TLE6251-2G | TLE62512GS |
|---|---|---|---|---|---|
| Product Type | High-speed CAN transceiver | High-speed CAN transceiver | High-speed CAN transceiver | High-speed CAN transceiver | High-speed CAN transceiver family reference |
| Package | DSO-14 | PG-DSO-14-24 | PG-DSO-14 | DSO-14 family package | DSO-14 family reference |
| Brand | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies |
Bảo phân biệt quan trọng
- Verified high-speed CAN rate (vsGeneric CAN transceiver with unspecified rate)
- Power-down behavior (vsGeneric transceiver without verified passive power-down)
- Diagnostic and low-power features (vsBasic CAN transceiver without verified wake or failure detection)
- Package-family continuity (vsCross-package CAN transceiver)
Ghi chú thiết kế
Place the TLE62512G close to the CANH and CANL connector or bus entry, and keep the CAN bus traces short, symmetrical, and continuous. Follow the Infineon recommended CAN transceiver layout for termination, common-mode return, and protection components. Do not route high-current power paths between the bus connector and transceiver because inductive spikes can degrade communication margin.
Use the exact supply and decoupling values from the manufacturer datasheet; the verified search excerpts do not provide them. Confirm the transceiver’s normal, sleep, and power-down sequencing so the CAN bus remains passive when the local supply is unavailable. This is particularly important in mixed-power-supply HS-CAN networks, where multiple nodes can be powered from different domains.
Do not treat a related distributor suffix as automatically interchangeable with TLE62512G. Before PCB release, compare the exact ordering code against the Infineon package drawing and pinout, then verify supply voltage, timing, sleep current, wake behavior, failure-detection signaling, and ESD ratings. A package-compatible appearance alone does not establish pin-to-pin or system-level compatibility.
Thông tin tuân thủ
The verified data confirms ISO 11898-5 compliance and ESD protection for the Infineon TLE6251-2G family, but it does not provide RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statements. Confirm these items in the current manufacturer documentation.
