Texas Instruments

TLV2764ID - Quad 500kHz RRIO Op Amp | Texas Instruments

MPN: TLV2764ID ✓ Hoạt động
1.8 V Vdss 20 uA Id 14-pin SOIC Package
MOQ: 1 |

TLV2764ID Tóm tắt

The Texas Instruments TLV2764ID is a quad, rail-to-rail input and output operational amplifier optimized for low-voltage, low-power signal conditioning. It operates from 1.8 V to 3.6 V, provides a 500 kHz gain-bandwidth product, and is packaged in a 14-pin SOIC. The four amplifiers share a common supply range and provide a practical combination of low quiescent current and useful closed-loop bandwidth for portable and industrial systems.

An operational amplifier is a high-gain, differential-input analog building block used to amplify, buffer, filter, compare, or reshape signals. The TLV2764 belongs to the rail-to-rail input/output amplifier family within the broader operational amplifier, analog IC, and semiconductor hierarchies. Rail-to-rail input operation increases the usable input range near either supply rail, while rail-to-rail output operation improves output swing on low-voltage systems where conventional amplifier headroom is limited.

The TLV2764ID integrates four amplifiers in one package, reducing board area and simplifying multi-channel designs. Key characteristics include a 500 kHz bandwidth, approximately 20 uA supply current per amplifier, and operation down to 1.8 V. These features make the device suitable for sensor conditioning, current-voltage conversion, low-voltage filtering, and general-purpose embedded analog signal paths where power consumption and integration are important.

The device is built for general-purpose analog applications operating across an industrial temperature range of -40 °C to 85 °C. Its 14-pin SOIC package supports conventional surface-mount assembly and is suitable for prototypes as well as production boards. The quad organization is especially useful when four related channels are needed, such as sensing multiple inputs, driving balanced circuitry, or implementing active filtering in compact instrumentation.

Typical uses include battery-powered sensor interfaces, portable measurement systems, industrial control modules, low-voltage data-acquisition nodes, and embedded analog signal conditioning. A 500 kHz bandwidth supports signals well beyond slow sensor outputs while retaining the low supply current required by compact embedded systems. Its rail-to-rail behavior also makes it useful when signal levels occupy much of the available supply range.

Designers should verify input and output common-mode limits, output-current capability, noise, offset, and stability requirements against the manufacturer datasheet. Decoupling capacitors should be placed close to the supply pins, and unused amplifier channels should be configured according to the recommended stable-input network. PCB grounding and signal routing should minimize parasitic feedback around high-gain stages.

This page combines device specifications, practical application guidance, pin-package information, and a strict same-footprint replacement analysis. It also distinguishes functionally similar amplifier families from genuine pin-to-pin options so engineers can assess PCB reuse without mistaking general-purpose similarity for drop-in compatibility.

Bộ thay thế dễ dàng lắp đặt cho TLV2764ID — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.

TLV2764IDR

✅ Drop-In
📦 14-pin SOIC
Same 4-channel, 500 kHz, 1.8 V-to-3.6 V electrical configuration; order format changes from TLV2764ID to the R tape-and-reel suffix, with no quantified core electrical difference.

📋 Tham chiếu thay thế (không có trong danh mục)

TLV2764IDG4

✅ Drop-In
📦 14-pin SOIC
Same 4-channel, 500 kHz, 1.8 V-to-3.6 V TLV2764 configuration in the 14-pin SOIC footprint; G4 is an ordering designation whose non-electrical commercial differences are 0% on the key performance ratings.

📋 Tham chiếu thay thế (không có trong danh mục)

TLV2764ID Tỷ lệ tối đa & tính chất điện

Amplifier Count 4 circuits
Product Type Quad operational amplifier
Minimum Supply Voltage 1.8 V
Maximum Supply Voltage 3.6 V
Gain-Bandwidth Product 500 kHz
Supply Current per Amplifier 20 uA
Input Common-Mode Range Rail-to-rail
Output Swing Rail-to-rail
Maximum Input Offset Voltage 3500 uV
Khoảng nhiệt độ hoạt động -40 °C to 85 °C
Package Type 14-pin SOIC
Số lượng chân 14 pins
Kiểu lắp đặt Surface mount
Supply Type Single supply
Trạng thái RoHS unknown
REACH Status unknown
AEC-Q100 Qualification not_applicable

Hướng dẫn cấu hình chân TLV2764ID 14-pin soic

Cấu hình chân cho TLV2764ID (14-pin soic gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.

Bảng cấu hình chân 14-pin soic cho TLV2764ID

Không có dữ liệu chân cụ thể sẵn có cho TLV2764ID.

Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.

Ứng dụng tiêu biểu

TLV2764ID phù hợp cho 6 Áp dụngs: Battery-Powered Sensor Conditioning, Portable Data Acquisition, Industrial Process Measurement, Low-Voltage Active Filtering, Battery Management Monitoring, Test and Measurement Buffering.

🧩

Battery-Powered Sensor Conditioning

The TLV2764ID fits low-power sensor interfaces because each amplifier consumes approximately 20 uA while the device supports supply rails down to 1.8 V. Its four channels can condition inputs from temperature, pressure, or resistive sensors without requiring four separate amplifier packages. Rail-to-rail input behavior is especially useful when a sensor output lies close to the lower or upper supply limit, while the 500 kHz bandwidth supports signals beyond static Wheatstone-bridge outputs. The practical benefit is lower board area and lower amplifier count, although input bias current, source impedance, and output settling must be checked against the selected sensor. A common-ground layout and short sensor traces help prevent the sensor itself from adding more noise than the amplifier.

📱

Portable Data Acquisition

The TLV2764ID is useful in compact data-acquisition nodes that must process several analog channels from a 1.8 V-to-3.6 V system. Its 500 kHz gain-bandwidth product provides enough closed-loop bandwidth for many sensor, transducer, and moderate-frequency instrumentation signals, while rail-to-rail output behavior increases usable range on low-voltage rails. Four amplifiers in one 14-pin SOIC reduce the number of packages compared with discrete single-channel solutions. When used as buffers or active filters, the device trades very low supply consumption against the exact noise, offset, and output-drive limits of the family. Designers should include output filtering and gain-selection components appropriate to the signal bandwidth, and verify settling at the intended closed-loop gain.

🏭

Industrial Process Measurement

The TLV2764ID can support multi-channel industrial measurement front ends that operate from low-voltage control rails. Four channels can amplify pressure, level, position, or current-loop signals while preserving a compact PCB footprint, and the -40 °C to 85 °C specified range covers common industrial environments. Rail-to-rail input and output characteristics help maximize usable signal range when supply headroom is constrained. The 500 kHz bandwidth is suitable for many process-control signals but does not replace the isolation, surge protection, and filtering often required at field inputs. Use short guarded traces, solid ground-plane continuity, and calibrated resistors around the amplifier stages. The device should remain on the regulated logic or analog rail rather than being connected directly to a field wiring harness.

📡

Low-Voltage Active Filtering

The TLV2764ID is well suited to active filters and signal conditioners in low-voltage embedded equipment because it combines four amplifiers, 500 kHz bandwidth, and approximately 20 uA supply current per channel. Its rail-to-rail output capability allows filter stages to use more of the available signal range than a conventional headroom-limited amplifier. Multiple filter sections can be implemented on one PCB without separate amplifier packages, reducing component count and simplifying power distribution. Gain and compensation choices should be checked against the manufacturer's stability guidance, particularly for capacitive loading or high closed-loop gain. Keep resistor networks close to the corresponding amplifier pins, maintain symmetrical routing where practical, and place any input or output RC components according to the desired cutoff rather than using arbitrary short stubs.

⚡

Battery Management Monitoring

The TLV2764ID can monitor low-voltage battery-system signals using its four amplifier channels, including cell-sense amplification, threshold conditioning, current-monitor amplification, and buffered references. Its low 1.8 V operating capability suits compact power systems, while rail-to-rail input behavior helps measure signals near the available supply range. The 500 kHz bandwidth is useful when the monitoring path must respond to changing load or cell conditions rather than only static voltage. Because battery nodes may experience rapid transients, the amplifier should be protected and isolated from those transients with appropriate upstream components. Engineers should verify the common-mode limits at the lowest battery voltage, ensure the output does not exceed downstream ADC limits, and account for the amplifier's offset when resolving small measurement changes.

🖥️

Test and Measurement Buffering

The TLV2764ID provides four unity-gain-compatible buffer channels for low-level test and measurement circuits operating from low-voltage rails. Rail-to-rail input and output behavior can preserve small test signals that would otherwise be compressed by the input and output limits of conventional amplifiers. The 500 kHz bandwidth accommodates many general-purpose measurement signals, while the approximately 20 uA per-channel supply current supports portable instruments. Four channels can buffer sources, condition differential pairs, or drive downstream ADC inputs. Designers should confirm source impedance, capacitive loading, and output-current requirements for each channel. Guard sensitive inputs, separate return currents from precision analog grounds, and keep input leads short to minimize pickup of noise and capacitance that could disturb settling.

Tóm tắt các sản phẩm được đề xuất

TLV2764IDR Same-family quad amplifier for tape-and-reel assembly Được sử dụng trong: Battery-Powered Sensor Conditioning, Industrial Process Measurement, Battery Management Monitoring INA240A1PW Texas Instruments Được sử dụng trong: Battery-Powered Sensor Conditioning TLV2764IDG4 Same-family quad amplifier ordering option Được sử dụng trong: Portable Data Acquisition, Low-Voltage Active Filtering, Test and Measurement Buffering LM324ADR Texas Instruments Được sử dụng trong: Portable Data Acquisition INA149AIDR Texas Instruments Được sử dụng trong: Industrial Process Measurement LM2902N/PB Texas Instruments Được sử dụng trong: Low-Voltage Active Filtering INA240A3DR Texas Instruments Được sử dụng trong: Battery Management Monitoring MAX3221IPWR Texas Instruments Được sử dụng trong: Test and Measurement Buffering
What is the operating voltage of TLV2764ID?
The TLV2764ID operates from 1.8 V to 3.6 V. According to the Texas Instruments TLV2764 product page, the device is a quad operational amplifier designed for low-voltage supply rails, with rail-to-rail input and output operation. This range makes it appropriate for low-voltage sensor, portable-instrument, and embedded analog systems. The complete operating limits and electrical test conditions are defined in the manufacturer datasheet.
What are the key specifications of TLV2764ID?
The TLV2764ID is a 4-circuit, 500 kHz operational amplifier with rail-to-rail input and output behavior, a 1.8 V to 3.6 V supply range, and approximately 20 uA supply current per amplifier. It is offered in a 14-pin SOIC and is specified from -40 °C to 85 °C. According to the Texas Instruments product page, these characteristics emphasize low-voltage operation, micropower consumption, and integration of four amplifiers in one package.
Where can I download the TLV2764ID datasheet PDF?
The official TLV2764ID technical information is available from the Texas Instruments product page at https://www.ti.com/product/TLV2764. The ordering-information table identifies TLV2764ID as the 14-pin SOIC version. Use the manufacturer's datasheet for the pin description, recommended operating conditions, electrical characteristics, typical performance curves, and application guidance rather than relying on a third-party transcription.
Where can I find the TLV2764ID pinout?
The TLV2764ID pinout is published in the pin-configuration and pin-description tables of the Texas Instruments TLV2764 datasheet. The device uses a 14-pin SOIC package, and its four operational amplifiers are arranged as two dual amplifier sections sharing supply pins. Use the package drawing and pin-description table when assigning PCB nets, especially for exposed supply and ground connections.
Is TLV2764ID suitable for low-voltage sensor applications?
Yes, the TLV2764ID is suitable for low-voltage sensor conditioning because it operates down to 1.8 V and provides rail-to-rail input and output behavior. Its 500 kHz gain-bandwidth product handles a substantially wider range of signals than a static sensor, while approximately 20 uA supply current per amplifier supports power-constrained designs. Input bias current, noise, and common-mode performance should still be checked against the sensor source impedance.
What is the best drop-in replacement for TLV2764ID?
The closest documented drop-in choices are TLV2764IDR and TLV2764IDG4, both in the 14-pin SOIC footprint. The TLV2764IDR is primarily a tape-and-reel ordering form of the same device, while TLV2764IDG4 is an ordering variant identified in a direct comparison. Confirm RoHS, REACH, temperature grade, and production-status requirements before substituting either part.
What can replace TLV2764ID?
A direct replacement should use the same 14-pin SOIC footprint, four-amplifier configuration, 1.8 V minimum supply, and approximately 500 kHz bandwidth. TLV2764IDR and TLV2764IDG4 satisfy the package and configuration requirements identified for the TLV2764 family. Amplifiers with fewer channels, different shutdown arrangements, or TSSOP packages are not direct replacements even if their basic gain-bandwidth ratings are similar.
Is TLV2764ID the same as TLV2764IDR?
The TLV2764ID and TLV2764IDR are the same 14-pin SOIC device configured for different order quantities and shipment formats. The TLV2764ID is commonly the tube or standard-package ordering code, while the R suffix denotes a tape-and-reel presentation. Their core electrical rating remains a quad, 500 kHz, rail-to-rail operational amplifier, although purchasing documents should always identify the exact suffix being quoted.
TLV2764ID vs TLV2764IDR — which is better for production PCB assembly?
Choose TLV2764IDR when automated PCB assembly consumes parts directly from tape and reel; choose TLV2764ID when the required purchasing or assembly format is a tube. Both use the same 14-pin SOIC footprint and belong to the same TLV2764 electrical family. The decision is therefore driven by assembly handling and order format rather than by a change in bandwidth, supply voltage, or amplifier count.
TLV2764ID vs TLV274IDR — which is better for a 14-pin SOIC design?
The TLV2764ID is the safer selection when four amplifiers are required, because it is a quad device with four channels in one 14-pin SOIC. The TLV274IDR comparison identifies a related amplifier family, but it is not automatically pin-to-pin interchangeable with the quad TLV2764ID. Use the manufacturer pin tables for any proposed substitution and treat a similar package as insufficient evidence of electrical or pin compatibility.
TLV2764ID vs TLV271IDR — which is better for a low-voltage amplifier design?
The TLV2764ID is preferable for designs requiring four amplifiers because it integrates four complete channels in a single 14-pin SOIC. A TLV271-family device is not a quad substitute and therefore cannot be treated as a pin-to-pin replacement. The TLV2764ID also provides the documented 500 kHz bandwidth and 1.8 V-to-3.6 V operating range for the target application.
When should I choose TLV2764ID over a single or dual amplifier?
Choose TLV2764ID when the design needs four matched functional channels and benefits from one 14-pin SOIC package. It reduces the number of amplifier packages, supply connections, and PCB placements compared with four single amplifiers or two dual amplifiers. Select a single or dual device instead when fewer channels are required, when channel count dictates the package, or when a particular amplifier family provides a necessary shutdown or output-current feature.
Is TLV2764ID in stock and what is its lead time?
Current stock and lead time should be requested through the Request a Quote form on this page. The component is listed as an active Texas Instruments orderable device, but production schedules and inventory can vary by quantity and order format. Use the exact 14-pin SOIC suffix TLV2764ID in the request so the supplier can confirm the correct package and delivery plan.
What is the price of TLV2764ID?
The current commercial price for TLV2764ID should be obtained through the Request a Quote form on this page. The form can confirm unit pricing, volume breaks, order quantity, and the exact 14-pin SOIC ordering format. Quoting the full manufacturer part number helps prevent confusion with TLV2764IDR, TLV2764IDG4, or amplifier options in other packages.
Where can I buy TLV2764ID online?
Use the Request a Quote form on this page to request TLV2764ID availability, lead time, and commercial terms. Specify the quantity, acceptable tape-and-reel or tube format, and required delivery destination. The exact manufacturer part number is TLV2764ID, which identifies the 14-pin SOIC configuration rather than the closely related R or G4 ordering suffixes.
Does TLV2764ID support rail-to-rail inputs and outputs?
Yes, the TLV2764ID supports rail-to-rail input and output operation according to the Texas Instruments product description. This is valuable on 1.8 V-to-3.6 V systems because it allows the amplifier to process input signals near the supply rails and improves available output range. Designers must still observe the exact common-mode, output-voltage, and output-current limits under the intended load and temperature.

Dữ liệu tham khảo kỹ thuật cho TLV2764ID — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.

Hướng dẫn chọn lựa

Choose the TLV2764ID for compact, low-voltage systems requiring four rail-to-rail amplifier channels, approximately 500 kHz bandwidth, and low supply consumption. It is especially suitable when four related analog functions justify combining them in one 14-pin SOIC. Choose TLV2764IDR when automated assembly requires the tape-and-reel order format, and choose TLV2764IDG4 when that ordering designation is required by purchasing or environmental documentation. Both are direct package-compatible choices. Use LM2902N/PB instead when only two channels are needed and a higher-voltage dual amplifier is preferable. Use LM2904PWR when a wider supply range or different output-current characteristics are more important than operation at 1.8 V. For any other substitute, verify pin assignments and stability rather than relying only on package similarity.

So sánh với các sản phẩm thay thế

Tham số Sản phẩm này TLV2764IDR TLV2764IDG4
Brand Texas Instruments Texas Instruments Texas Instruments
Package 14-pin SOIC 14-pin SOIC - same 14-pin SOIC - same
Amplifier Count 4 circuits 4 circuits 4 circuits
Minimum Supply Voltage 1.8 V 1.8 V 1.8 V
Maximum Supply Voltage 3.6 V 3.6 V 3.6 V
Gain-Bandwidth Product 500 kHz 500 kHz 500 kHz
Supply Current per Amplifier 20 uA 20 uA 20 uA
Input and Output Operation Rail-to-rail input and output Rail-to-rail input and output Rail-to-rail input and output
Operating Temperature Range -40 °C to 85 °C -40 °C to 85 °C -40 °C to 85 °C

Bảo phân biệt quan trọng

  • Four rail-to-rail amplifiers in one 14-pin SOIC (vsLM2902N/PB)
  • Lower-voltage operation with rail-to-rail signal handling (vsLM2904PWR)
  • Documented 500 kHz bandwidth with approximately 20 uA supply current per amplifier (vsTLV2764IDR)

Ghi chú thiết kế

Place the supply-decoupling capacitor immediately between the amplifier supply and ground pins, with a short and low-inductance connection. Keep analog input and feedback traces away from switching nodes and high-current paths. Because the TLV2764ID contains four amplifiers in one 14-pin SOIC, check the pin table before assigning each channel; similar-looking amplifier packages can use different channel and supply arrangements. Preserve a continuous ground plane beneath the device when possible.

Do not assume that every low-voltage operational amplifier with a similar bandwidth is pin-compatible. Rail-to-rail input and output behavior, output-current capability, noise, offset, common-mode limits, and stable operation with capacitive loads can differ substantially between families. Before accepting a substitute, compare the manufacturer pin descriptions and electrical characteristics under the actual supply voltage, gain, load, and temperature. Unused channels should be configured according to the manufacturer recommendations.

The 500 kHz gain-bandwidth product limits useful closed-loop bandwidth as gain rises and should not be confused with a guaranteed full-unity-gain output range under every load. Use the manufacturer stability and output-capacitance guidance when driving long cables, ADC sample-and-hold inputs, or capacitive loads. Add isolation resistors close to the output where necessary, and verify settling time for the selected gain before using the amplifier in a precision acquisition path.

Thông tin tuân thủ

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Không chì
Unknown
Không halogen
Unknown
Khoáng vật xung đột
Unknown

No specific RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification statement is present in the technical product summaries. The device is a general-purpose industrial-temperature amplifier rather than an automotive-qualified variant.

Dữ liệu được xác minh vào: 2026-11-15 — dữ liệu được xác minh và quản lý bởi đội ngũ kỹ thuật phần cứng của XAIPART

Tìm kiếm liên quan

TLV2764ID datasheet TLV2764ID datasheet pdf TLV2764ID pinout TLV2764ID specifications TLV2764ID equivalent TLV2764ID replacement TLV2764ID vs TLV2764IDR TLV2764ID 14-SOIC pinout TLV2764ID low voltage op amp TLV2764ID 500kHz amplifier TLV2764ID sensor interface Texas Instruments TLV2764ID TLV2764ID price TLV2764ID stock

Các bộ phận và thuật ngữ liên quan

Texas Instruments TLV2764ID TLV2764IDR TLV2764IDG4 quad operational amplifier operational amplifier analog IC semiconductor rail-to-rail input rail-to-rail output RRIO gain-bandwidth product 500 kHz 1.8 V 3.6 V 20 uA SOIC-14 SOIC package family surface mount SMD sensor conditioning data acquisition active filter industrial measurement battery monitoring
Báo giá nhanh RFQ
Hãy điền đầy đủ thông tin — đội ngũ bán hàng của chúng tôi sẽ phản hồi trong vòng 24 giờ
Mã sản phẩm Nhà sản xuất Kiểu đóng gói QTY Giá mục tiêu Phụ
✓
Báo giá đã gửi!

Chúng tôi sẽ trả lời email của bạn trong vòng 24 giờ

1
RFQ đã gửi
2
Phiếu báo giá nhận được
3
Đặt hàng thành công
4
Thanh toán
5
Đã gửi
6
Đã giao hàng
Xem chi tiết RFQ