STMicroelectronics

TS924IDT - Quad Rail-to-Rail Op Amp, 4 MHz | STMicroelectronics

MPN: TS924IDT ✓ Hoạt động
2.7 V to 12 V Vdss 15 nA Id 14-pin Small Outline (SO-14) Package
MOQ: 1 |

TS924IDT Tóm tắt

The STMicroelectronics TS924IDT is a quad, rail-to-rail BiCMOS operational amplifier optimized for 3 V and 5 V operation, with four amplifiers housed in a 14-pin Small Outline package. Key specifications include a 4 MHz gain-bandwidth product, 1.3 V/µs slew rate, and a 2.7 V to 12 V supply-voltage range.

An operational amplifier is an active analog signal-conditioning device that amplifies the voltage difference between its inverting and non-inverting inputs. The TS924 belongs to the quad operational-amplifier family, placing four amplifiers in one package to reduce component count in multi-channel instrumentation. Its rail-to-rail input and output architecture supports low-voltage signal chains in which the usable common-mode and output ranges extend close to the supply rails.

The BiCMOS construction combines bipolar input transistors with CMOS output stages. In the TS924, this architecture supports low input-bias current of 15 nA, a 4 MHz unity-gain bandwidth, and 1.3 V/µs slew rate. The device is specified for both 3 V and 5 V systems and operates across a supply range of 2.7 V to 12 V. The operating temperature range extends from -40 °C to +125 °C.

Typical applications include current-to-voltage conversion in precision measurement systems, sensor-signal conditioning, low-voltage audio circuits, active filtering, and general-purpose analog signal conditioning. Because four matched amplifier channels share one package, designers can also use the device for dual-rail control loops, quad sensor interfaces, and multi-axis signal acquisition.

When laying out a TS924IDT circuit, place each decoupling capacitor close to its corresponding supply pin and keep feedback resistors and input traces short to minimize parasitic capacitance. Verify the input common-mode range, output-current capability, and capacitive-load stability against the load connected to each amplifier. The SO-14 outline is suitable for conventional surface-mount assembly and supports design reuse across the STMicroelectronics TS92x family.

This page consolidates the manufacturer specifications, package and lifecycle information, price references, cross-reference findings, and practical design guidance into one engineering-focused resource for evaluating the TS924IDT in new analog designs.

Bộ thay thế dễ dàng lắp đặt cho TS924IDT — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.

Các biến thể trong loạt này

Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với TS924IDT (cùng hình factor và footprint) — khác nhau ở Package, Amplifier Type, Supply Voltage Range, RoHS Status, Slew Rate.

STMicroelectronics
Package: 14-pin small-outline package (14-SO)
Amplifier Type: Rail-to-Rail operational amplifier
Supply Voltage Range: 3 V to 5 V operation
So sánh với TS924IDT →
STMicroelectronics
Package: 16-pin SOIC
Slew Rate: 1.3 V/us
So sánh với TS924IDT →
STMicroelectronics
Package: SOIC-16, 16-SO
Amplifier Type: Quad general-purpose operational amplifier
Supply Voltage Range: 3 V to 12 V
So sánh với TS924IDT →
STMicroelectronics
Package: 14-pin SOIC
So sánh với TS924IDT →

TS924AIDT

✅ Drop-In ⚠️ Thông số chưa được xác minh
📦 SO-14
Enhanced TS924A family variant in the same 14-pin SO footprint; electrical characteristics require verification against the TS924

📋 Tham chiếu thay thế (không có trong danh mục)

TS924ID

✅ Drop-In
STMicroelectronics
📦 SO-14
4 circuits · Rail-to-Rail operational amplifier · BiCMOS · 3 V to 5 V operation · 80 mA · 80 dB · 0.1 µA · 5000 µV

Liên hệ để biết giá

Xem tài liệu →

TS925IDT

✅ Drop-In
STMicroelectronics
📦 SO-14
Quad general-purpose operational amplifier · 4 circuits · Yes · Yes · 3 V to 12 V · 3 V and 5 V · 4 MHz · 1.3 V/us

Liên hệ để biết giá

Xem tài liệu →

TS924AID

✅ Drop-In
📦 SO-14
Enhanced TS924A family in the same 14-pin SO footprint; uses a different ordering designation from TS924IDT

📋 Tham chiếu thay thế (không có trong danh mục)

TS925ID

✅ Drop-In ⚠️ Thông số chưa được xác minh
STMicroelectronics
📦 SO-14
4 amplifiers · 4 circuits · General-purpose operational amplifier · Rail-to-rail · Rail-to-rail · 4 MHz · 1.3 V/us · 2.7 V to 12 V

Liên hệ để biết giá

Xem tài liệu →

TS925AIDT

✅ Drop-In ⚠️ Thông số chưa được xác minh
📦 SO-14
Enhanced TS925A variant in the same 14-pin SO package; bandwidth, slew rate, and accuracy require comparison with TS924IDT

📋 Tham chiếu thay thế (không có trong danh mục)

TS924IDT Tỷ lệ tối đa & tính chất điện

Number of Amplifiers 4
Amplifier Type General-purpose operational amplifier
Architecture BiCMOS
Rail-to-Rail Input and output
Supply Voltage Range 2.7 V to 12 V
Optimized Supply Voltage 3 V and 5 V
Gain-Bandwidth Product 4 MHz
Slew Rate 1.3 V/µs
Input Bias Current 15 nA
Khoảng nhiệt độ hoạt động -40 °C to +125 °C
Hộp 14-pin Small Outline (SO-14)
Kiểu lắp đặt Surface mount
Output Current Capability High output current
Trạng thái RoHS Compliant
Trạng thái vòng đời Active
Manufacturer Lead Time 3-7 business days

Cấu hình chân TS924IDT

SOIC-14 (3.9mm) Package Pinout Diagram SOIC-14 14-pin small outline IC, 3.9x8.7mm, P1.27mm, JEDEC MS-012. Pin 1 by chamfer. 1 14 2 13 3 12 4 11 5 10 6 9 7 8 SOIC-14 (3.9mm)
Chân 1 OUT1 — Amplifier 1 output
Chân 2 -IN1 — Amplifier 1 inverting input
Chân 3 +IN1 — Amplifier 1 non-inverting input
Chân 4 V- — Negative supply or ground
Chân 5 +IN2 — Amplifier 2 non-inverting input
Chân 6 -IN2 — Amplifier 2 inverting input
Chân 7 OUT2 — Amplifier 2 output
Chân 8 OUT3 — Amplifier 3 output
Chân 9 -IN3 — Amplifier 3 inverting input
Chân 10 +IN3 — Amplifier 3 non-inverting input
Chân 11 V+ — Positive supply
Chân 12 +IN4 — Amplifier 4 non-inverting input
Chân 13 -IN4 — Amplifier 4 inverting input
Chân 14 OUT4 — Amplifier 4 output

Ứng dụng tiêu biểu

TS924IDT phù hợp cho 6 Áp dụngs: Precision Sensor Signal Conditioning, Low-Voltage Audio Output Stages, Active Filtering and Equalization, Current-to-Voltage Measurement, Industrial Control and Data Acquisition, Portable and Battery-Powered Instruments.

🧩

Precision Sensor Signal Conditioning

The TS924IDT suits four-channel sensor conditioning because its four rail-to-rail amplifiers fit into one 14-pin SO package while maintaining 15 nA input-bias current. Connect each amplifier as a non-inverting or differential stage around a resistive sensor network, then place a short feedback path close to the device. The 4 MHz gain-bandwidth product supports useful closed-loop bandwidth above audio frequencies, while the 1.3 V/µs slew rate produces full-scale transitions quickly. For high-impedance sensors, evaluate input leakage, offset voltage, and noise over the -40 °C to +125 °C operating range before fixing the gain.

🎧

Low-Voltage Audio Output Stages

For headphone buffers, line-level output stages, or small-signal audio amplification, the TS924IDT provides rail-to-rail output behavior and a 1.3 V/µs slew rate in a 3 V or 5 V design. Its high-output-current architecture is intended to support moderate capacitive and resistive loads more effectively than a general-purpose micropower amplifier. Place output resistors or isolation networks where required by the load, and verify capacitive-load stability from the manufacturer guidance. The four channels can support dual stereo pairs or a mixer architecture without requiring four separate amplifier packages.

🔧

Active Filtering and Equalization

The TS924IDT is appropriate for active filters and equalizer sections where multiple identical amplifiers share one package. A 4 MHz gain-bandwidth product gives sufficient loop-gain reserve for many low-frequency filter sections, and the 1.3 V/µs slew rate helps preserve signal amplitude through fast transitions. Build each second-order section with local feedback resistors and capacitors, keeping the amplifier output separated from high-impedance summing nodes. Check stability with the actual source impedance and load capacitance, especially when the filter also performs current-to-voltage conversion.

📷

Current-to-Voltage Measurement

The TS924IDT can implement transimpedance amplifiers for photodiodes, electrochemical sensors, and other current-producing devices. Its 15 nA input-bias current reduces the error associated with high-value feedback resistors, while the 4 MHz bandwidth and 1.3 V/µs slew rate support responsive measurement of transient currents. Use a guarded, low-leakage feedback node and avoid long PCB traces into the inverting input. Because photodiode capacitance and cable capacitance can destabilize the high-gain stage, follow the application guidance in the manufacturer datasheet or add an isolation resistor and compensation capacitor.

🏭

Industrial Control and Data Acquisition

The -40 °C to +125 °C operating range and 2.7 V to 12 V supply capability make the TS924IDT suitable for industrial control boards that condition several low-level channels. The quad configuration can amplify thermocouple, bridge-sensor, pressure, or position-sensor outputs without requiring four separate amplifiers. For 24 V industrial environments, regulate the supply down to the supported range before the device. Verify input protection, transient immunity, grounding, and channel-to-channel isolation according to the final EMC and safety requirements of the end equipment.

📱

Portable and Battery-Powered Instruments

A portable instrument running from a 3 V or 5 V rail can use the TS924IDT when rail-to-rail signal handling is more important than minimum quiescent current. The device combines four amplifiers in a single SO-14 package, reducing board area compared with four separate single-amplifier packages. Its low-bias-current input stage also suits sensors with high source impedances. Current consumption still depends on the complete signal chain and selected operating point, so evaluate quiescent current for the intended duty cycle and confirm the battery voltage range against the device specifications.

What is the TS924IDT?
The TS924IDT is a quad rail-to-rail BiCMOS operational amplifier from STMicroelectronics, with four amplifiers in a 14-pin Small Outline package. According to the manufacturer datasheet, the device is optimized and fully specified for 3 V and 5 V operation, supports a 2.7 V to 12 V supply range, and provides a 4 MHz gain-bandwidth product with 1.3 V/µs slew rate.
What is the operating voltage of the TS924IDT?
The TS924IDT operates from a 2.7 V to 12 V supply. The manufacturer datasheet identifies 3 V and 5 V as the primary optimized operating points, making the amplifier suitable for low-voltage analog systems that do not require a higher rail. Design the circuit so its signal amplitudes and output swing remain inside the input and output ranges specified for the selected supply voltage.
What are the key specifications of TS924IDT that engineers should know?
The TS924IDT combines four rail-to-rail amplifiers, a 4 MHz gain-bandwidth product, 1.3 V/µs slew rate, and 15 nA input-bias current in one SO-14 package. STMicroelectronics specifies it for 2.7 V to 12 V operation, with performance optimized at 3 V and 5 V. Its -40 °C to +125 °C temperature range covers industrial environments, while the low-bias-current input stage suits high-impedance sensor interfaces.
Where can I download the TS924IDT datasheet PDF?
The official TS924IDT datasheet PDF is available from STMicroelectronics at the manufacturer datasheet link on this page. It is titled “Rail-to-rail output current quad operational amplifier” and covers the TS924 and TS924A devices. Use the manufacturer PDF for the authoritative pin description, electrical characteristics, typical performance curves, and application guidance when designing a new board.
Where can I find the TS924IDT pinout?
The TS924IDT pinout is documented in the pin-description table of the STMicroelectronics TS924 datasheet. This 14-pin SO package contains four complete amplifier channels: four non-inverting inputs, four inverting inputs, four outputs, one positive-supply connection, and one ground connection. Use the package drawing and pin table together when assigning PCB nets and checking routing continuity.
Is the TS924IDT suitable for low-voltage sensor interfaces?
Yes, the TS924IDT is well suited to many low-voltage sensor-interface circuits because its rail-to-rail inputs, 15 nA input-bias current, and 2.7 V minimum supply voltage support operation close to the supply rails. Confirm that the sensor output stays within the amplifier's input common-mode range and evaluate the noise and offset performance required by the measurement before fixing the gain and feedback network.
What is the best drop-in replacement for TS924IDT?
The closest same-family replacement is the TS924AIDT, which retains the 14-pin Small Outline format and the TS924 family function while using the enhanced TS924A variant. A second same-brand option is TS925IDT, which also uses a 14-pin Small Outline package and provides pin-compatible channel functions, although its electrical characteristics can differ. Confirm the full operating conditions and AC parameters in the relevant manufacturer datasheet before production substitution.
Can TS925IDT replace TS924IDT?
TS925IDT can serve as a pin-compatible 14-pin Small Outline alternative when its channel functions and electrical limits meet the design requirements. The TS924IDT is specified at 4 MHz bandwidth and 1.3 V/µs slew rate, while the TS925 family has different electrical characteristics. Verify supply range, input common-mode range, output swing, and stability with the required load before treating it as a drop-in replacement.
TS924IDT vs TS924AIDT - which is better for a new design?
Choose TS924AIDT when the enhanced TS924A family characteristics are preferred, and choose TS924IDT when its 4 MHz bandwidth, 1.3 V/µs slew rate, and 15 nA input-bias current meet the original design requirements. Both use the same 14-pin Small Outline device family and are intended for 3 V and 5 V systems. Review both manufacturer datasheets for offset, noise, and load-drive differences.
When should I choose TS924IDT instead of TS924AIDT?
Choose TS924IDT when an existing design has already been validated around the TS924 family's 4 MHz bandwidth, 1.3 V/µs slew rate, and 15 nA input-bias current, especially when component continuity matters. Select TS924AIDT for a new design when the enhanced family variant offers preferable electrical characteristics. Package interchangeability does not remove the need to verify DC accuracy, noise, and stability.
What can replace TS924IDT in an existing PCB design?
TS924AIDT and TS925IDT are the most practical same-brand 14-pin Small Outline candidates for a board-level substitution. Both preserve the four-amplifier SO-14 format, but a valid replacement also requires compatible input common-mode range, output swing, supply voltage, and stability. Review the relevant manufacturer datasheet and test the actual board, because the package being identical does not guarantee identical performance.
Is the TS924IDT the same as the TS924ID?
TS924IDT and TS924ID represent closely related ordering forms of the same STMicroelectronics device family, and comparison listings describe their terminals and packages as consistent. The “T” suffix denotes the tape-and-reel ordering configuration associated with this listing, while TS924ID is commonly listed without that packing suffix. Confirm the required packing method and the manufacturer ordering information before substituting the labels.
Is the TS924IDT RoHS compliant?
Yes, the TS924IDT is identified as RoHS compliant in the product listing for this exact ordering code. STMicroelectronics lists the device as active, and the component is supplied in a 14-pin Small Outline package. For a complete environmental declaration, review the current manufacturer product page and the applicable material-compliance documentation associated with your procurement lot.
Where can I buy TS924IDT and request a quote?
Use the “Request a Quote” form on this page to request TS924IDT pricing, stock confirmation, and a current delivery quotation from XAIPART. The product is listed as active, and a manufacturer-channel listing indicates a typical lead time of 3-7 business days. Submit the required quantity, target packaging, and shipment location with the inquiry so the quotation reflects the exact order configuration.
What is the price of TS924IDT?
Current TS924IDT pricing is obtained through the “Request a Quote” form on this page, where the quantity and delivery details you enter are used to prepare an offer. The listed component is a 14-pin SO quad rail-to-rail operational amplifier rated for 2.7 V to 12 V operation. Requesting a quote also allows stock, lead-time, and traceability requirements to be confirmed for the exact MPN.
How much current can the TS924IDT output drive?
The TS924IDT is characterized by the manufacturer as a rail-to-rail high-output-current quad operational amplifier, making it suitable for driving moderate loads rather than only high-impedance sensing circuits. Exact output-current limits depend on supply voltage, output voltage, and temperature. Consult the output-current and output-voltage-swing characteristics in the STMicroelectronics datasheet before loading an amplifier stage.

Dữ liệu tham khảo kỹ thuật cho TS924IDT — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.

Hướng dẫn chọn lựa

Choose the TS924IDT for 3 V or 5 V analog systems that need four rail-to-rail amplifier channels, low input-bias current, and a 4 MHz bandwidth in one SO-14 package. It is a strong fit for sensor conditioning, transimpedance measurement, active filtering, and moderate-load audio or control circuits. Select TS924AIDT for a new design when the enhanced TS924A family variant is preferred after comparing accuracy and noise. TS925IDT is a practical SO-14 alternative when its distinct bandwidth, slew rate, and output-drive characteristics better match the load. LM2902N/PB may be preferred for a dual-amplifier design that does not need rail-to-rail operation, but it does not reduce package count in the same way. For any substitution, verify supply range, common-mode range, output swing, offset, noise, and capacitive-load stability rather than relying only on the package outline.

So sánh với các sản phẩm thay thế

Tham số Sản phẩm này TS924AIDT TS924ID TS925IDT TS924AID TS925ID
Brand STMicroelectronics STMicroelectronics STMicroelectronics STMicroelectronics STMicroelectronics STMicroelectronics
Package SO-14 SO-14 SO-14 SO-14 SO-14 SO-14
Number of Amplifiers 4 4 4 4 4 4
Architecture BiCMOS BiCMOS BiCMOS BiCMOS BiCMOS BiCMOS
Supply Voltage Range 2.7 V to 12 V 2.7 V to 12 V 2.7 V to 12 V 2.7 V to 12 V 2.7 V to 12 V 2.7 V to 12 V
Optimized Operating Point 3 V and 5 V 3 V and 5 V 3 V and 5 V 3 V and 5 V 3 V and 5 V 3 V and 5 V
Rail-to-Rail Operation Input and output Input and output Input and output Input and output Input and output Input and output

Bảo phân biệt quan trọng

  • Four-channel integration in one package (vsLM2902N/PB)
  • Rail-to-rail signal handling at low supply voltage (vsLM2902N/PB)
  • Specified dynamic performance for the TS924 family (vsTS925IDT)
  • Low-bias-current input stage for sensor interfaces (vsLM324ADR)

Ghi chú thiết kế

Route the four inverting-input and four non-inverting-input connections away from the supply pins and output traces. High-impedance inputs are particularly sensitive to leakage through contaminated PCB surfaces or nearby high-impedance nets. Place the input-bias-current compensation or guarding network recommended in the manufacturer application guidance directly beside the relevant input pin rather than extending it across the board.

Place the supply bypass capacitor immediately across the V+ and V- pins, with the shortest possible ground return. Because the package contains four amplifiers sharing one supply connection, the total supply current is four times the average current drawn by each channel. Use a regulator and capacitor arrangement that can supply the summed channel current plus transient demand without producing supply droop that distorts all four outputs simultaneously.

Do not assume that an identical 14-pin footprint guarantees identical behavior. When substituting TS924AIDT, TS925IDT, TS924AID, or TS925ID, verify input common-mode range, output swing, input offset, noise, slew rate, bandwidth, and capacitive-load stability at the intended supply voltage. The TS924IDT's 4 MHz bandwidth and 1.3 V/µs slew rate should be compared with the selected alternative before releasing a production change.

Keep feedback components close to the associated amplifier pins and avoid routing the high-impedance summing node beneath or between output traces. For transimpedance applications, minimize the capacitance at the inverting input and follow the datasheet's guidance for stability with photodiode or cable capacitance. An isolation resistor between the source and inverting input can help control high-frequency feedback when the physical board cannot be optimized.

Thông tin tuân thủ

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
Không chì
Unknown
Không halogen
Unknown
Khoáng vật xung đột
Unknown

RoHS compliance is identified for the exact TS924IDT ordering code. No automotive qualification is claimed for this general-purpose amplifier.

Dữ liệu được xác minh vào: 2026-11-16 — dữ liệu được xác minh và quản lý bởi đội ngũ kỹ thuật phần cứng của XAIPART

Tìm kiếm liên quan

TS924IDT datasheet TS924IDT pinout TS924IDT datasheet pdf TS924IDT SO-14 STMicroelectronics TS924IDT TS924IDT specifications TS924IDT rail-to-rail op amp TS924IDT 4 MHz 1.3 V/us TS924IDT drop-in replacement TS924IDT vs TS925IDT TS924IDT equivalent amplifier TS924IDT price TS924IDT stock TS924IDT sensor interface quad 3V rail-to-rail amplifier TS924IDT

Các bộ phận và thuật ngữ liên quan

STMicroelectronics TS924IDT TS924AIDT TS924ID TS925IDT TS924AID TS925ID quad operational amplifier rail-to-rail amplifier BiCMOS analog signal conditioning current-to-voltage conversion sensor interface gain-bandwidth product slew rate input-bias current common-mode range output swing small outline package SO-14 surface mount RoHS 3 V operation 5 V operation
Báo giá nhanh RFQ
Hãy điền đầy đủ thông tin — đội ngũ bán hàng của chúng tôi sẽ phản hồi trong vòng 24 giờ
Mã sản phẩm Nhà sản xuất Kiểu đóng gói QTY Giá mục tiêu Phụ
✓
Báo giá đã gửi!

Chúng tôi sẽ trả lời email của bạn trong vòng 24 giờ

1
RFQ đã gửi
2
Phiếu báo giá nhận được
3
Đặt hàng thành công
4
Thanh toán
5
Đã gửi
6
Đã giao hàng
Xem chi tiết RFQ