TS944AID - Quad Rail-to-Rail Micropower Op Amp | STMicroelectronics
MPN: TS944AID ✗ Cuối đờiTS944AID Tóm tắt
An operational amplifier is a high-gain analog building block used to amplify, buffer, filter, and compare small voltage signals. The TS944AID belongs to the rail-to-rail output operational-amplifier family, combining four independent amplifier channels with a common supply in one compact 14-pin package. Rail-to-rail output operation allows the output voltage to approach the supply rails more closely than a conventional fixed-headroom amplifier, improving usable signal range in low-voltage systems.
The four-channel arrangement reduces package count and simplifies routing in designs requiring several similar amplifier stages. A 2.5 V minimum supply supports low-energy systems, while the 10 V maximum supply provides flexibility for conventional industrial signal ranges. The approximately 1.2 µA supply current per channel is particularly valuable when every microwatt affects battery life. The -40°C to +85°C operating range supports industrial equipment and consumer products requiring operation beyond room temperature.
STMicroelectronics describes the TS944 series as micropower, rail-to-rail output operational amplifiers. Its four-channel architecture is useful for sensor conditioning, current-loop receivers, filtering, and low-level signal buffering. Because the TS944AID combines four amplifiers in one package, matching channels can simplify calibration, reduce board area, and keep sensitive analog paths physically close. Decoupling and stable-reference techniques remain important when the amplifier operates beside switching circuitry or long sensor cables.
Typical uses include industrial pressure and temperature sensors, low-power condition-monitoring equipment, portable measurement instruments, analog interface boards, and general-purpose signal buffers. In a sensor front end, two channels can amplify or level-shift sensor outputs while the remaining channels support filtering, threshold detection, or output buffering. Its low supply current is advantageous when the complete system must operate from a small energy source rather than a laboratory supply.
For PCB design, place the supply bypass capacitor close to the device and route high-impedance input and feedback traces away from switching nodes and fast digital signals. Confirm output swing, input common-mode range, stability, and capacitive-load limits against the manufacturer datasheet for the actual supply voltage and load. Verify the exact pin orientation and channel assignments before assembly because the SOIC-14 outline alone does not identify the functional pins.
This product page consolidates the device identity, operating envelope, package information, replacement considerations, and application-oriented design guidance. It also distinguishes confirmed family information from parameters that require direct consultation of the manufacturer datasheet before precision analog design or PCB release.
Bộ thay thế dễ dàng lắp đặt cho TS944AID — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với TS944AID (cùng hình factor và footprint) — khác nhau ở Package, Input Bias Current, Input Type, Number of Amplifier Channels, Number of Pins.
TS944IPT
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →TS944A
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
TS944AI
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
TS944AID Tỷ lệ tối đa & tính chất điện
| Product Type | Quad operational amplifier |
| Number of Amplifier Channels | 4 circuits |
| Supply Voltage Range | 2.5 V to 10 V |
| Supply Current per Channel | 1.2 µA |
| Total Typical Supply Current | 4.8 µA |
| Kiểu đầu ra | Rail-to-rail output |
| Khoảng nhiệt độ hoạt động | -40°C to +85°C |
| Hộp | 14-pin SOIC |
| Kiểu lắp đặt | Surface mount |
| Số lượng chân | 14 pins |
| Amplifier Category | General-purpose amplifier |
| Power Class | Micropower |
Hướng dẫn cấu hình chân TS944AID 14-pin soic
Cấu hình chân cho TS944AID (14-pin soic gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho TS944AID.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
TS944AID phù hợp cho 6 Áp dụngs: Battery-Powered Sensor Conditioning, Industrial Pressure and Temperature Measurement, Low-Power Data Acquisition, Portable Environmental Monitoring, Signal Buffering and Active Filtering, Analog Interface and Threshold Detection.
Battery-Powered Sensor Conditioning
The TS944AID is well suited to low-energy sensor interfaces because four amplifier channels operate from 2.5 V to 10 V while each channel consumes approximately 1.2 µA. A compact front end can use the channels for sensor amplification, reference buffering, active filtering, and threshold detection without requiring four separate packages. The rail-to-rail output architecture improves available signal swing in low-voltage systems. When designing a battery-powered conditioner, confirm the sensor output range and common-mode requirements against the manufacturer electrical characteristics, and account for leakage from switches, protection devices, and external resistors. This approach reduces package count while preserving a low-power architecture suited to portable environmental or condition-monitoring equipment.
Được đề xuất
Industrial Pressure and Temperature Measurement
The TS944AID can support multichannel industrial measurement circuitry where several low-level sensor signals must be conditioned close to the acquisition electronics. Its 2.5 V to 10 V supply range and -40°C to +85°C operating range support industrial equipment, while the four-channel SOIC-14 package simplifies routing and provides matching amplifier types in one device. The low typical supply current of approximately 1.2 µA per channel is valuable when the instrument must operate from limited power. Use the channels for signal amplification, filtering, buffering, or level detection, and verify input common-mode limits, offset, noise, and output swing at the actual supply voltage before production release.
Được đề xuất
Low-Power Data Acquisition
The TS944AID is useful in compact data-acquisition systems that require several analog channels but cannot justify the power or area of larger amplifiers. Its four channels can condition successive sensor inputs or process simultaneous signals from a low-power multiplexer, while approximately 1.2 µA per channel limits the amplifier contribution to system standby current. The 14-pin SOIC package also reduces the number of external amplifier footprints. Design the acquisition front end with attention to source impedance, settling behavior, channel-switching transients, and reference stability. The manufacturer datasheet should be used to confirm bandwidth and settling requirements for the selected sampling rate and acquisition architecture.
Được đề xuất
Portable Environmental Monitoring
The TS944AID fits portable environmental-monitoring equipment that combines temperature, humidity, gas, or vibration sensing with battery-powered operation. The low 2.5 V minimum supply and approximately 1.2 µA per-channel supply current help preserve energy reserves, while four channels allow a compact implementation of sensor amplification, filtering, and alarm detection. Rail-to-rail output operation provides improved output range when the monitored variable is measured close to a supply rail. Because sensor cables can introduce noise and ground offsets, keep sensitive traces away from external connectors and digital switching nodes. Confirm offset, bias-current, noise, and common-mode behavior in the manufacturer datasheet for the selected sensor source impedance.
Được đề xuất
Signal Buffering and Active Filtering
The TS944AID can implement multiple buffered or active-filter stages within one 14-pin SOIC package. The rail-to-rail output characteristic is useful for buffers that must preserve signal range near the supply limits, while the low per-channel current suits distributed low-power analog blocks. Designers can allocate channels to unity-gain buffers, gain stages, anti-alias filters, or active level-shifting networks as required. Verify noise, gain accuracy, output-drive capability, and capacitive-load stability for the actual source and load impedances. Keep feedback-loop traces compact and maintain a quiet ground reference to minimize channel-to-channel interaction, especially when filtering small signals or using long external resistor networks.
Được đề xuất
Analog Interface and Threshold Detection
The TS944AID can combine analog buffering with comparator-style threshold functions in a low-voltage interface circuit. Four available channels provide flexibility for conditioning a sensed voltage, amplifying an error signal, driving a filtered reference, and detecting a limit condition. The 2.5 V to 10 V supply range accommodates low-energy systems, while approximately 1.2 µA per channel supports reduced standby demand. Threshold accuracy will depend on input offset, offset drift, noise, and reference quality, so these parameters must be checked in the manufacturer electrical tables. Use hysteresis or filtering where appropriate to prevent repeated switching near the threshold, and account for output behavior under the selected capacitive load.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho TS944AID — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | TS944 | TS944A | TS944AI |
|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Package | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC |
| Amplifier Channels | 4 circuits | 4 circuits | 4 circuits | 4 circuits |
| Supply Voltage Range | 2.5 V to 10 V | 2.5 V to 10 V | 2.5 V to 10 V | 2.5 V to 10 V |
| Supply Current per Channel | 1.2 µA | 1.2 µA | 1.2 µA | 1.2 µA |
| Output Type | Rail-to-rail output | Rail-to-rail output | Rail-to-rail output | Rail-to-rail output |
Bảo phân biệt quan trọng
- Four amplifier channels in one package (vsLM324ADR)
- Rail-to-rail output operation (vsLM324KDR)
- Very low per-channel supply current (vsLM2904PWR)
Ghi chú thiết kế
Place the supply bypass capacitor immediately adjacent to the power and ground pins, and use a short, low-inductance connection between the capacitor and the device. High-impedance input and feedback paths should remain away from the bypass-capacitor return current and digital switching nodes. For sensor interfaces, keep connector-side protection components away from the amplifier inputs and route the quiet ground return without sharing high-current paths whenever practical.
Do not assume that rail-to-rail output automatically means the input common-mode range reaches both supply rails. Check the manufacturer electrical characteristics at the actual supply voltage, especially when sensing near 2.5 V. Likewise, verify output swing under the intended load and confirm capacitive-load stability before placing significant capacitance directly on an amplifier output. These checks prevent offset errors, clipping, and oscillation in compact analog modules.
For low-level signals, use short feedback resistors, minimize input-node capacitance, and keep sensitive traces away from sources of steep switching edges. If the TS944AID drives an ADC input, add or preserve the manufacturer-recommended isolation resistor and verify settling at the ADC acquisition bandwidth. For longer sensor cables, consider guarding, differential conversion, or filtering before the amplifier input rather than relying on the amplifier alone to reject interference.
The four amplifiers typically contribute about 4.8 µA when each channel operates at the quoted 1.2 µA, but the complete power budget must also include input bias current, output leakage, reference circuits, protection devices, and external bias networks. Estimate the worst-case current using the manufacturer maximum values rather than the typical value. Confirm that the source can support startup, load transients, and the system sleep state without causing rail collapse.
Thông tin tuân thủ
A reseller listing states that the obsolete TS944AID is RoHS compliant, but no manufacturer declaration was identified for this MPN. Other compliance attributes require confirmation from STMicroelectronics.