TS972IPT - Dual Low-Noise Rail-to-Rail Op Amp | STMicroelectronics
MPN: TS972IPT ✓ Hoạt độngTS972IPT Tóm tắt
The TS972 belongs to the TS97x family of low-noise operational amplifiers. An operational amplifier is an analog signal-processing IC that uses high open-loop gain to amplify differences between two input voltages. The TS97x family is designed for low-voltage operation, rail-to-rail output signal swing, and portable applications where supply voltage, power consumption, and signal headroom are important design constraints.
Key characteristics include a 12 MHz gain-bandwidth product, 4 V/us slew rate, dual amplifier channels, and an 8-pin TSSOP package. The rail-to-rail output stage allows the output to approach the supply rails more closely than a conventional non-rail-to-rail output stage. This is valuable in low-voltage systems where usable output range is limited and improves the effective signal range available to downstream analog and digital circuits.
The TS97x family operates with voltages as low as ±1.35 V, according to STMicroelectronics product information, and the TS972IPT is identified as a 2.7 V to 10 V supply-range device in the listed technical data. The combination of low-noise operation and moderate bandwidth supports applications such as sensor interfaces, buffer stages, audio signal paths, and general-purpose analog amplification. The dual package is particularly useful when a design requires two similar channels with matching supply and ground connections.
Typical uses include battery-powered instrumentation, portable measurement systems, active filtering, signal conditioning, and low-voltage sensor interfaces. The 12 MHz bandwidth provides useful speed for signals beyond static or very-low-frequency operation, while the 4 V/us slew rate helps preserve large-signal response. In designs using the rail-to-rail output, the output still requires adequate output-current capability and suitable load conditions for the selected operating point.
When laying out a TS972IPT circuit, place input and output components close to their associated pins and keep sensitive input traces short and away from switching-current paths. Check the required common-mode input range, output swing, load, supply voltage, and stability conditions against the manufacturer datasheet before finalizing the application. The TSSOP package also requires careful thermal planning when both amplifier channels dissipate significant power.
Bộ thay thế dễ dàng lắp đặt cho TS972IPT — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với TS972IPT (cùng hình factor và footprint) — khác nhau ở Package, Amplifier Type, Number of Amplifiers.
TS972IQT
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →TS972IYPT
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
TS462CPT
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
TS972IPT Tỷ lệ tối đa & tính chất điện
| Amplifier Type | Dual operational amplifier |
| Number of Amplifiers | 2 |
| Gain-Bandwidth Product | 12 MHz |
| Slew Rate | 4 V/us |
| Supply Voltage Range | 2.7 V to 10 V |
| Minimum Total Supply Voltage | ±1.35 V |
| Output Swing | Rail-to-rail signal swing |
| Unity-Gain Bandwidth | 12 MHz |
| Hộp | 8-pin TSSOP |
| Kiểu lắp đặt | Surface mount |
| Trạng thái vòng đời | Active |
Hướng dẫn cấu hình chân TS972IPT 8-pin tssop
Cấu hình chân cho TS972IPT (8-pin tssop gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho TS972IPT.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
TS972IPT phù hợp cho 6 Áp dụngs: Battery-Powered Sensor Interface, Portable Instrumentation, Active Filtering, Audio Signal Conditioning, Industrial Control Signal Conditioning, General-Purpose Analog Buffering.
Battery-Powered Sensor Interface
TS972IPT fits low-voltage sensor front ends that need more usable signal range than a conventional amplifier output can provide. Its rail-to-rail output swing and operation from a low supply are useful for buffering pressure, temperature, and position sensors without wasting headroom. The two channels can amplify or buffer complementary signals on one board, while 12 MHz bandwidth provides margin for moderately responsive sensor systems. Designers should verify the sensor output range against the input common-mode limits and select resistor values that preserve signal-chain stability.
Được đề xuất
Portable Instrumentation
TS972IPT is appropriate for portable measurement instruments powered from a low-voltage battery or regulated rail. The dual amplifier arrangement reduces package count when processing two channels, while rail-to-rail output improves measurement utilization in compact systems. Its 12 MHz bandwidth and 4 V/us slew rate are suitable for instrument blocks that need moderate signal bandwidth rather than only static accuracy. Layout should keep sensitive inputs away from display, reference, and switching-supply paths to avoid injecting noise into the measurement result.
Được đề xuất
Active Filtering
TS972IPT can implement active filters and signal-conditioning blocks where the 12 MHz gain-bandwidth product offers useful loop-gain margin beyond low-frequency sensor signals. Two channels allow paired filter sections or a filter plus output buffer on the same TSSOP package. Rail-to-rail output can improve headroom in low-voltage filter designs, but component tolerances, feedback-network scaling, and the amplifier's noise and stability characteristics must be checked during simulation. Place feedback and compensation components close to the corresponding amplifier pins.
Được đề xuất
Audio Signal Conditioning
TS972IPT can serve as a low-voltage audio preamplifier or signal-conditioning stage when the circuit requires two related channels and moderate bandwidth. The 12 MHz gain-bandwidth product accommodates audio-band signals with additional loop margin, and rail-to-rail output can increase headroom in portable audio equipment. The dual-channel configuration is useful for stereo or balanced audio paths. Verify output load, output-current capability, noise performance, and channel matching against the manufacturer data before using it where channel symmetry is critical.
Được đề xuất
Industrial Control Signal Conditioning
TS972IPT is suitable for low-voltage industrial signal-conditioning stages where sensor outputs must be amplified before conversion or control. The dual-channel package supports two inputs from one controller while simplifying supply distribution, and the rail-to-rail output helps preserve range in compact control assemblies. The 4 V/us slew rate is useful for signals with faster transitions than typical slow process sensors. Confirm the operating-temperature range and electromagnetic-immunity requirements for the final equipment before deployment.
Được đề xuất
General-Purpose Analog Buffering
TS972IPT works as a dual unity-gain buffer when a design needs to isolate a high-impedance source from a downstream load. Rail-to-rail output helps preserve signal amplitude at low supply voltages, while the dual configuration allows buffering of two nodes in a compact circuit. The 12 MHz bandwidth provides more capability than a purely low-frequency reference buffer. Validate source impedance, capacitive loading, output stability, and thermal behavior with the actual source and load because generic buffer assumptions may not apply at the extremes of the operating range.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho TS972IPT — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
Ghi chú thiết kế
Route the two input pairs and feedback networks as short, compact loops. Keep amplifier inputs away from supply-current return paths and switching nodes because input capacitance can convert high-current edges into voltage noise. Place the feedback resistors directly beside the relevant amplifier pins, and maintain a quiet ground reference for both channels when the device performs differential or instrumentation-style signal conditioning.
Decouple the supply pins locally with the capacitance required by the manufacturer application guidance and place the high-frequency bypass capacitor at the package power pin. Check the supply voltage against both the absolute maximum and the operating region. Low-voltage operation is supported, but the available output swing still depends on the load and must be evaluated before assuming a rail-to-rail output reaches either supply rail.
Do not treat rail-to-rail output as unlimited output swing or current capability. Confirm common-mode input range, output-current limits, load impedance, and stability with the actual circuit. Also verify that the selected 8-pin TSSOP footprint and pin assignments match the exact suffix; closely related TS97x parts may differ in temperature grade, reel code, or qualification rather than electrical function.
Estimate dissipation from the actual supply voltage, output voltage, and load current in each amplifier channel. Because the TS972IPT contains two amplifiers in one TSSOP package, both channels can contribute to the package's total heating. Use the manufacturer thermal information for the exact package and board environment, then preserve copper around the device and avoid placing heat-sensitive components immediately beside the TSSOP in high-load conditions.
Thông tin tuân thủ
No explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statement is present in the available product information. As a general-purpose operational amplifier, the automotive qualification field is treated as not applicable unless the exact ordering suffix is qualified for automotive use.