TUSB1106PWR USB 2.0 Transceiver | Texas Instruments
MPN: TUSB1106PWR ✓ Hoạt độngTUSB1106PWR Tóm tắt
A USB transceiver is an interface integrated circuit that converts between a host controller or peripheral controller’s digital signaling and the physical D+ and D- differential pair used by USB. In the broader electronics hierarchy, the TUSB1106 belongs to the USB interface IC family, interface transceivers, and power-management-aware connectivity semiconductors. It provides the physical-layer path for exchanging serial data and detecting bus state in USB 2.0 systems.
The TUSB1106 family supports both full-speed and low-speed USB data rates. Full-speed operation provides a higher-rate communication option for peripherals that require more throughput, while low-speed operation supports devices with modest bandwidth requirements and suitable device-state behavior. USB 2.0 Revision 2.0 compliance is specifically identified for the TUSB1105 and TUSB1106 transceivers by Texas Instruments.
The TUSB1106PWR is a half-duplex, one-channel transceiver, matching the “1/1 Transceiver Half” device description shown in the product listing. Its differential USB data interface connects to the external data and power behavior of the USB link, while control and configuration pins support integration into host or peripheral designs. The single USB channel makes the device appropriate for compact equipment, industrial control modules, embedded systems, and accessory interfaces that require one USB physical transceiver.
Typical design locations include USB host controllers, USB peripheral controllers, portable test equipment, industrial interface cards, and embedded USB-to-serial or USB communication subsystems. The device should be placed near the USB connector so that the high-speed differential traces remain short, continuous, and impedance controlled. Connector-side protection, proper D+ and D- routing, and compliance with the USB signal-integrity requirements are more important than adding unrelated circuit functions.
When designing a replacement circuit, verify the complete pin description, electrical limits, operating-temperature range, and USB compliance requirements against the manufacturer datasheet. The principal engineering trade-off is that this device supports USB 2.0 full-speed and low-speed signaling rather than USB high-speed operation at 480 Mbit/s. For new designs that require high-speed USB data rates, select a transceiver explicitly specified for that speed instead.
This page organizes the verified manufacturer and distributor information into an engineering-oriented view covering USB data rates, package format, application fit, comparison criteria, and practical design guidance. The package and interface hierarchy are emphasized so engineers can identify whether the TUSB1106PWR matches the intended USB physical-layer design.
Bộ thay thế dễ dàng lắp đặt cho TUSB1106PWR — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
TUSB1105PWR
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
TUSB1106PWR Thông số kỹ thuật
| Device Type | USB full-speed/low-speed transceiver |
| Number of Channels | 1 channel |
| Transceiver Configuration | Half-duplex, 1/1 transceiver |
| USB Standard Compliance | Universal Serial Bus Specification Revision 2.0 |
| Full-Speed Data Rate | 12 Mbit/s |
| Low-Speed Data Rate | 1.5 Mbit/s |
| Package Type | 16-pin TSSOP (PW) |
| Số chân | 16 pins |
| Kiểu lắp đặt | Surface mount |
Hướng dẫn cấu hình chân TUSB1106PWR 16-pin tssop (pw)
Cấu hình chân cho TUSB1106PWR (16-pin tssop (pw) gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho TUSB1106PWR.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
TUSB1106PWR phù hợp cho 6 Áp dụngs: Embedded USB Peripheral Interface, Industrial Control Module, USB Test and Measurement Adapter, Portable Device Accessory, USB-to-Serial Bridge, Security and Access Controller.
Embedded USB Peripheral Interface
The TUSB1106PWR fits an embedded peripheral that communicates through a USB full-speed or low-speed connection. Its 12 Mbit/s full-speed rate is suitable for command exchange, configuration transfer, firmware update, and moderate data streaming, while the 1.5 Mbit/s low-speed rate supports simpler device functions. Place the transceiver close to the USB connector, route D+ and D- as a controlled differential pair, and connect the device’s USB controller according to the manufacturer pin-description table. The main benefit is a dedicated single-channel physical layer in a 16-pin TSSOP package; the design must not be treated as a 480 Mbit/s high-speed solution.
Được đề xuất
Industrial Control Module
The TUSB1106PWR can provide the USB physical interface for an industrial control module that uses a host computer to configure equipment or exchange operating data. Full-speed operation at 12 Mbit/s offers more bandwidth than low speed, while USB Specification Revision 2.0 compatibility supports a broadly established device architecture. Keep the transceiver and connector region separated from noisy switching stages, use a continuous reference plane, and apply connector-side ESD protection. Because this is a one-channel transceiver, designs needing multiple simultaneous USB links should use additional devices or a multi-channel controller.
Được đề xuất
USB Test and Measurement Adapter
The TUSB1106PWR is appropriate for compact test adapters and instrumentation interfaces that exchange commands and sampled data over USB full speed. Its 12 Mbit/s maximum stated full-speed rate can support moderate control traffic and data transfer without requiring a high-speed transceiver. Place the device near the external connector to minimize trace length, maintain matched D+ and D- geometry, and decouple supply pins according to the manufacturer recommendations. The advantage is a dedicated half-duplex USB physical layer in a 16-pin TSSOP footprint; system throughput may also be limited by the connected controller and USB host.
Được đề xuất
Portable Device Accessory
A portable electronic accessory can use the TUSB1106PWR for a full-speed USB connection to a computer or charger-compatible interface. The 16-pin TSSOP package is practical for compact single-port designs, and the device supports both 12 Mbit/s full-speed and 1.5 Mbit/s low-speed operation. Layout quality is critical: route D+ and D- over uninterrupted ground, keep connector and protection components close together, and avoid long stubs. The device does not perform USB power negotiation or battery charging, so those functions must be handled separately by the host-side system.
Được đề xuất
USB-to-Serial Bridge
The TUSB1106PWR can serve as the USB physical layer in a USB-to-serial bridge that exposes a serial interface to an embedded controller. Full-speed operation at 12 Mbit/s is suitable for configuration consoles, firmware transport, and moderate data-transfer functions. Position the transceiver at the USB connector edge, maintain impedance continuity for the differential pair, and isolate it from clocks, switching regulators, and high-current actuator drivers. Since the TUSB1106 handles one half-duplex USB channel rather than the serial protocol itself, the companion controller must implement the required bridge and data framing.
Được đề xuất
Security and Access Controller
The TUSB1106PWR can support a USB connection for an access-control or security peripheral that exchanges enrollment data, status, and audit information with a host. Its full-speed mode provides 12 Mbit/s while low-speed support allows lower-bandwidth device functions where appropriate. Keep the USB trace geometry compact and isolated from security-sensitive analog or sensing circuitry, and follow the manufacturer’s recommended decoupling and grounding arrangement. This device supplies only the USB transceiver function, so authentication, cryptographic processing, and secure storage must be implemented by dedicated system components.
Được đề xuất
Dữ liệu tham khảo kỹ thuật cho TUSB1106PWR — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | TUSB1105PWR |
|---|---|---|
| Package | 16-pin TSSOP (PW) | 16-pin TSSOP (PW) |
| Brand | Texas Instruments | Texas Instruments |
| Device Type | USB transceiver | USB transceiver |
| Channel Count | 1 channel | 1 channel |
| USB Specification | Universal Serial Bus Specification Revision 2.0 | Universal Serial Bus Specification Revision 2.0 |
| Full-Speed Data Rate | 12 Mbit/s | 12 Mbit/s |
| Low-Speed Data Rate | 1.5 Mbit/s | 1.5 Mbit/s |
Bảo phân biệt quan trọng
- Single-channel half-duplex USB interface (vsTUSB1105PWR)
- USB Revision 2.0 full-speed operation (vsTUSB1105PWR)
- Low-speed compatibility (vsTUSB1105PWR)
Ghi chú thiết kế
Route the USB D+ and D- conductors as a short, tightly coupled differential pair over a continuous ground plane. Keep the transceiver close to the USB connector, remove unnecessary stubs, and avoid changing layer stackups between the connector, protection components, and transceiver. USB signal integrity depends on the complete path, so confirm the implemented geometry with the layout rules and test limits appropriate for 12 Mbit/s operation.
Do not substitute this part for a USB high-speed transceiver: the stated maximum operating rate is 12 Mbit/s full speed, not 480 Mbit/s. Also verify the complete pin description and supply requirements against the manufacturer datasheet rather than treating the 16-pin TSSOP outline as sufficient proof of compatibility. A footprint match alone does not establish electrical, control, or protocol equivalence.
Place connector-side protection and any required series impedance components close to the USB connector and follow the manufacturer’s recommended placement around the transceiver. Provide local supply decoupling using the capacitance and layout specified in the datasheet. Maintain a low-impedance ground return beneath the differential pair and separate the USB routing region from switching nodes and high-current power paths.
Thông tin tuân thủ
USB Specification Revision 2.0 compliance is stated by Texas Instruments for the TUSB1105 and TUSB1106 family. RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status are not established by the available manufacturer and distributor information.