產品(42,000+)

MTFC4GLDDQ-4M - 32Gb Managed NAND e-MMC Flash | 100-LBGA
MTFC4GLDDQ-4M

MTFC4GLDDQ-4M - 32Gb Managed NAND e-MMC Flash | 100-LBGA

The Micron MTFC4GLDDQ-4M is a 32 Gbit managed NAND flash memory device built on the e-MMC (embedded MultiMediaCard) interface, housed in a 100-pin LBGA package (14x18 mm). It integrates a NAND flash array with an on-die controller, providing managed flash with built-in ECC, wear leveling, and bad-block management across an industry-standard 32 Gbit / 4 GB capacity. The 3.3 V supply rail and HS-MMC compatible host interface make it drop-in compatible with widely deployed e-MMC host controllers. A managed NAND flash memory IC combines a raw NAND flash die with an integrated memory management controller on the same package. Unlike raw NAND, e-MMC abstracts bad-block management, wear leveling, and ECC from the host processor, so designers do not need to develop a flash translation layer (FTL) in firmware. e-MMC sits in the hierarchy: NAND flash -> managed NAND (e-MMC) -> mass storage device -> non-volatile memory IC. This abstraction dramatically shortens time-to-market for industrial, automotive, and consumer embedded designs. Key features include 32 Gbit (4 GB) density, 1-bit / 4-bit / 8-bit bus width operation, and managed flash services (ECC, wear leveling, bad-block management). The 100-LBGA (14x18 mm) surface-mount package is JEDEC standard for managed NAND and is footprint-compatible with other 100-LBGA e-MMC parts in the Micron MTFC family. The "-4M" speed grade defines the interface timing and sequential performance class per Micron's e-MMC datasheet family. Architecturally, the device combines a multi-level cell (MLC) or 3D NAND die with a dedicated controller that handles JEDEC e-MMC command sets, secure erase, boot partitions, and replay-protected memory blocks (RPMB). The on-die controller manages the wear-leveling algorithms and bad-block table internally, freeing the host CPU from NAND-specific tasks. Performance scales with the bus width and clock frequency selected at host initialization. Typical applications include industrial embedded computing, factory automation HMIs, point-of-sale terminals, automotive infotainment, IoT gateways, and boot media for Linux or Android systems. Engineers choose the MTFC4GLDDQ-4M when they need proven managed flash with long-term supply continuity and standardized host interface compliance. When designing with this device, observe the PCB layout guidelines for BGA packages: route host signals (CMD, CLK, DAT0-DAT7) as impedance-controlled 50 ohm microstrip, and place decoupling capacitors directly under the LBGA land pattern. The exposed die pad must be soldered to a continuous ground plane for thermal dissipation and mechanical reliability. Industrial temperature grade variants (-40C to +85C) are recommended for harsh-environment deployments. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on the manufacturer product page or third-party listings.

詢價 聯絡我們
MTFC64GAPALBH-IT - 64GB eMMC 5.1 Industrial NAND | Micron
MTFC64GAPALBH-IT

MTFC64GAPALBH-IT - 64GB eMMC 5.1 Industrial NAND | Micron

The Micron MTFC64GAPALBH-IT is a 64 Gbit (64 GB) managed NAND flash memory device integrating an MMC controller and 4x NAND L05B MLC 128Gb die in a 153-ball TFBGA (11.5x13 mm) surface-mount package. The part is JEDEC eMMC 5.1 compliant (JESD84-B51), supports HS400 high-speed interface timing, and operates from VCC 2.7-3.6 V with a dual-voltage VCCQ interface at 1.70-1.95 V or 2.7-3.6 V. An eMMC (embedded MultiMediaCard) is a managed-NAND package that combines raw MLC/TLC NAND flash with an onboard controller handling wear-leveling, bad-block management, and ECC. eMMC belongs to the managed NAND product family, which sits between raw NAND (requiring an external controller) and UFS (a faster, more advanced managed-NAND interface). The integration of controller + NAND + firmware dramatically simplifies host firmware, allowing even resource-constrained microcontrollers and Linux SoCs to add reliable mass storage with minimal driver development. Key features of the MTFC64GAPALBH-IT include an operating temperature range of -40C to +85C (industrial grade, indicated by the -IT suffix), HS400 bus interface mode, advanced 12-signal bus features, and an 8-bit data width organized as 8G x 8. The -IT ordering code designates industrial temperature and a specific firmware/feature set optimized for long-life industrial designs rather than consumer or automotive. Architecturally, the device embeds a MultiMediaCard controller that arbitrates access to four 128 Gb MLC NAND dice behind a standard MMC bus, exposing boot partitions, RPMB, and user-area partitions to the host. The controller also implements background operations like garbage collection and wear-leveling, offloading these from the application processor. The HS400 interface mode pushes the bus to 200 MHz DDR, achieving sequential read speeds substantially higher than legacy HS200 mode. Typical applications include industrial IoT gateways, factory automation HMIs, point-of-sale terminals, medical instrumentation data loggers, and Linux-based single-board computers. The 64 GB capacity is well-suited to storing operating system images, application data, and multimedia assets in a compact, soldered-down footprint. Designers should note the power-loss protection guidance from Micron application notes, as sudden VCC collapse during write operations can cause data corruption if decoupling and write-abort firmware handling are inadequate. When laying out the PCB, place the MTFC64GAPALBH-IT on a clean inner or outer ground plane with the VCCQ decoupling capacitors within 2 mm of the balls. Avoid routing noisy switching signals under the package and follow Micron's reference layout for the 153-ball TFBGA escape. The -IT grade's wide temperature range enables deployment in outdoor enclosures, but the design must still account for the thermal derating curve of the MLC NAND endurance at high temperature. This page synthesizes distributor pricing, drop-in alternatives, application companion parts, and design notes not found in the manufacturer datasheet alone, providing engineers with a one-stop reference for sourcing, designing, and qualifying the MTFC64GAPALBH-IT in production.

詢價 聯絡我們
MTFDKCC15T3TGH-1BC1ZABYY-TR - 15.36TB PCIe Gen4 U.3 SSD | Micron
MTFDKCC15T3TGH-1BC1ZABYY-TR

MTFDKCC15T3TGH-1BC1ZABYY-TR - 15.36TB PCIe Gen4 U.3 SSD | Micron

The Micron MTFDKCC15T3TGH-1BC1ZABYY-TR is a 9400 PRO series enterprise NVMe solid-state drive delivering 15.36 TB of TLC NAND capacity in a 2.5-inch U.3 (15 mm) form factor with a PCIe Gen4 x4 interface. It targets read-intensive data center workloads, supporting 1 drive write per day (DWPD) over a 5-year endurance rating. An enterprise NVMe SSD is a high-performance, low-latency non-volatile storage device built around the NVMe (Non-Volatile Memory Express) protocol over a PCIe interface, designed to replace SAS/SATA SSDs in hyperscale and tier-1 server platforms. Within the storage hierarchy it sits between DRAM (volatile cache) and HDD cold storage (bulk capacity), and within the broader taxonomy it belongs to: SSD -> solid-state storage -> data-center storage -> enterprise IT infrastructure. U.3 (formerly SFF-TA-1001) is the universal backplane form factor that accepts NVMe PCIe, SAS, and SATA drives in the same 2.5-inch bay, simplifying mixed-protocol chassis design. Key features of the 9400 PRO 15.36 TB include Micron's 176-layer TLC NAND, a Gen4 x4 NVMe 1.4 interface delivering up to 7.0 GB/s sequential read and 7.0 GB/s sequential write, up to 1.6M IOPS random read (4 KB), and on-drive capacitors for power-loss protection (PLP). AES-256 hardware encryption and end-to-end data path protection are standard, and the drive carries a 5-year limited warranty with MTBF ratings typical of the 9400 family. The 9400 PRO platform uses Micron's proprietary controller and firmware tuned for read-intensive service profiles such as content delivery, AI/ML training data lakes, large-object analytics, and boot/scratch virtualization. Compared to the 9400 MAX family (mixed-use, 3 DWPD), the PRO tier offers the same capacity envelope and interface but at lower write endurance, lowering $/GB for read-heavy workloads. Typical deployments include hyperscale virtualization, AI/ML training data staging, large-scale NoSQL and analytics clusters, software-defined storage nodes, and high-density read-cache tiers. The 15 mm Z-height fits standard 2.5-inch U.3 backplanes used in Dell PowerEdge, HPE ProLiant, and Supermicro platforms. When integrating this drive, validate backplane support for U.3 NVMe PCIe Gen4, ensure host platform NVMe driver compatibility with NVMe 1.4, and provision thermal airflow because sustained sequential reads can push the case temperature well above 60C in dense chassis. The "-TR" suffix indicates Tape & Reel / tray packaging for OEM system integrators rather than retail box. This page synthesizes distributor pricing, same-capacity drop-in alternatives within the U.3 PCIe Gen4 ecosystem, and practical design notes that go beyond the manufacturer datasheet's parameter tables.

詢價 聯絡我們
MTFDKCC7T6TFR-1BC1ZABYY-TR - 7.68TB NVMe U.3 7450 PRO SSD | Micron
MTFDKCC7T6TFR-1BC1ZABYY-TR

MTFDKCC7T6TFR-1BC1ZABYY-TR - 7.68TB NVMe U.3 7450 PRO SSD | Micron

The Micron MTFDKCC7T6TFR-1BC1ZABYY-TR is a 7.68TB enterprise-class NVMe U.3 solid-state drive from the Micron 7450 PRO Series, built on a 2.5-inch SFF (15 mm height) form factor with a PCIe 4.0 x4 NVMe interface. It is rated for read-intensive (RI) workloads at 1 DWPD endurance, uses Micron's TLC NAND technology, and provides sequential read throughput of up to 6,800 MB/s with sequential write up to 5,300 MB/s according to the Micron 7450 product family datasheet. A U.3 NVMe SSD is a 2.5-inch enterprise storage module that combines the SFF-8639 hot-swap form factor with the NVMe protocol stack on PCIe 4.0, replacing legacy SATA/SAS SSDs in modern servers. Within the storage taxonomy, the part sits under NAND flash memory -> SSD -> enterprise NVMe SSD -> data center NVMe SSD. The 7450 PRO family uses Micron's 176-layer TLC NAND, an in-house controller, and includes features such as AES-256 hardware encryption, power-loss protection (PLP), and TCG-compliant security options. Key differentiating specifications include 7.68 TB of TLC capacity in a 15 mm z-height, sequential read up to 6,800 MB/s and sequential write up to 5,300 MB/s, 1 DWPD (drive writes per day) over a 5-year warranty for read-intensive workloads, NVMe 1.4 protocol compliance, and AES-256 / TCG Opal security support depending on firmware. The PRO tier differs from the MAX (mixed-use, 3 DWPD) and from the SED/Non-SED firmware options. Compared to SATA SSDs, the 7450 PRO delivers roughly 10x sequential throughput and dramatically higher IOPS. Typical applications for this drive include hyperscale and enterprise data-center workloads such as read-intensive databases, content-delivery networks (CDN), boot drives for high-density servers, AI/ML training data lakes, virtual desktop infrastructure (VDI), software-defined storage nodes, and large-scale analytics platforms. It is also commonly deployed in mainstream server refresh projects transitioning legacy SATA/SAS storage to NVMe PCIe Gen4. Design considerations include U.3 backplane compatibility, thermal management under sustained sequential writes (the 15 mm height provides a larger heat-spreading surface than the 7 mm variant), and ensuring the host platform supports NVMe 1.4 with PCIe 4.0 x4 lanes. The -TR suffix indicates Tape-and-Reel / single-pack shipping configuration per Micron's part-number decoder. Unlike the related 7450 MAX drives, the PRO tier is optimized for read-intensive workloads and offers higher capacity at lower cost per GB. This page synthesizes distributor pricing, same-family Micron alternatives, datasheet references, and practical integration notes that are not aggregated in any single manufacturer document.

詢價 聯絡我們
MUX708-Q1 - Automotive 44V 8:1 Multiplexer | Texas Instruments
MUX708-Q1

MUX708-Q1 - Automotive 44V 8:1 Multiplexer | Texas Instruments

The Texas Instruments MUX708-Q1 is an automotive-qualified, 8:1 single-channel analog multiplexer designed for high-voltage applications. It features low on-resistance (5.4Ω typical) and supports bidirectional analog and digital signals on the source (Sx) and drain (D) pins, with a signal range from VSS to VDD. The device operates from a single supply (4.5V to 44V), dual supplies (±4.5V to ±22V), or asymmetric supplies (such as VDD = 12V, VSS = -5V), providing flexibility in various automotive and industrial systems. An analog multiplexer is a device that selects one of several analog input signals and forwards it to a single output. In the hierarchy of signal routing components, an analog multiplexer falls under analog switches and multiplexers, which are part of the broader category of interface ICs. These components are essential in data acquisition systems, where multiple sensors need to share a single ADC input, and in automotive body control modules for routing signals from various switches and sensors. Key features of the MUX708-Q1 include AEC-Q100 qualification for automotive applications, with device temperature grade 1 (-40°C to 125°C ambient operating temperature). It is latch-up immune and has HBM classification level H1C and CDM classification level C3. The device supports 1.8V logic, enabling direct interface with low-voltage microcontrollers without level shifters. Its low on and off leakage currents and ultra-low charge injection make it suitable for precision analog signal routing. The MUX708-Q1 is built on a robust architecture that ensures reliable operation in harsh automotive environments. The low on-resistance minimizes signal attenuation, while the wide supply range allows operation in 12V and 24V automotive systems. The device's bidirectional capability allows it to pass signals in either direction, making it versatile for both multiplexing and demultiplexing applications. Typical applications include automotive battery management systems, where it routes voltage and temperature sensor signals to a central ADC, and infotainment systems for audio signal routing. It is also used in industrial process control for sensor multiplexing and in test equipment for signal routing. When designing with the MUX708-Q1, ensure that the supply voltages are within the specified range and that the signal pins do not exceed VSS or VDD. Proper decoupling capacitors on the supply pins are recommended to maintain signal integrity.

詢價 聯絡我們
MUX80X-Q1 - 100V Flat RON Analog Multiplexer | TI
MUX80X-Q1

MUX80X-Q1 - 100V Flat RON Analog Multiplexer | TI

The Texas Instruments MUX80X-Q1 family, comprising the MUX808-Q1 (single 8:1) and MUX809-Q1 (dual 4:1), are high-voltage analog multiplexers designed for automotive and industrial applications. These devices support a maximum supply voltage of 100V and operate with dual, single, or asymmetric supplies. They provide consistent analog parametric performance across the entire supply voltage range, ensuring reliable signal routing in demanding environments. The MUX80X-Q1 devices are available in industry-standard TSSOP and small WQFN packages, offering design flexibility and space savings. An analog multiplexer is a semiconductor device that routes one of several analog input signals to a single output, controlled by digital select lines. In the hierarchy of signal routing components, an analog multiplexer falls under analog switches and multiplexers, which are part of the broader category of interface ICs. These devices are essential in data acquisition systems, test equipment, and automotive electronics where multiple sensor signals need to be selectively measured or routed. Key features of the MUX80X-Q1 include latch-up immunity, 1.8V logic compatibility, and flat ON-resistance (RON) across the input voltage range. The flat RON minimizes signal distortion and ensures accurate signal transmission. The devices support bidirectional analog and digital signals on the source (Sx) and drain (Dx) pins, making them versatile for both analog and digital multiplexing. The 1.8V logic compatibility allows direct interface with modern low-voltage microcontrollers and FPGAs without additional level shifting. Technically, the MUX80X-Q1 devices are built on a high-voltage CMOS process that enables operation up to 100V. The flat RON characteristic is achieved through careful design of the switch architecture, providing a nearly constant resistance over the full input voltage range. This reduces harmonic distortion and improves signal integrity, particularly in precision measurement applications. The latch-up immunity ensures robust operation in harsh automotive environments where transient voltages are common. Typical applications include automotive battery management systems, industrial process control, and automated test equipment. In automotive battery management, the MUX80X-Q1 can route voltage and temperature sensor signals from multiple battery cells to a single ADC, reducing component count and cost. In industrial process control, it enables multiplexing of analog sensor signals from various points in a plant to a central monitoring system. The high voltage rating and automotive qualification (Q1) make it suitable for 48V automotive systems and other high-voltage applications. When designing with the MUX80X-Q1, ensure that the supply voltage does not exceed the absolute maximum rating of 100V. Proper decoupling of the supply pins with 0.1uF ceramic capacitors is recommended to maintain stable operation. Additionally, consider the ON-resistance and its effect on signal attenuation, especially in high-impedance circuits.

詢價 聯絡我們
MVF50NN151CMK50 - Vybrid VF5xx 32-bit MPU 500MHz 364-LFBGA | NXP
MVF50NN151CMK50

MVF50NN151CMK50 - Vybrid VF5xx 32-bit MPU 500MHz 364-LFBGA | NXP

The NXP MVF50NN151CMK50 is a single-core 32-bit microprocessor from the Vybrid VF5xx family, integrating an ARM Cortex-A5 core running at 500 MHz with 1.5 MB of on-chip SRAM in a 364-ball LFBGA package measuring 17x17 mm. The device combines an applications processor-class core with a rich set of peripherals including DDR2/DDR3 memory controllers, two Execute-in-Place (XIP) quad-SPI interfaces, dual high-speed USB 2.0 with integrated PHYs, dual Ethernet MACs with an integrated L2 switch, and a digital video camera interface, making it a true system-on-chip for connected multimedia applications. What is an ARM Cortex-A5 MPU? An MPU (microprocessor unit) is a higher-performance variant of a microcontroller that typically lacks on-chip flash and runs from external memory. The ARM Cortex-A5 is an applications-class core implementing the ARMv7-A architecture with a memory management unit (MMU), enabling full operating systems such as Linux and Android. It sits in the Cortex-A family between the Cortex-A7 (newer, more power-efficient) and the older ARM926/ARM11 cores, balancing performance with low silicon cost. NXP positions the Vybrid VF5xx family at the intersection of microcontroller-level integration and applications-processor-level performance. Key differentiating features include hardware cryptography acceleration for secure boot and TLS, a 32-channel DMA engine, dual SDHC ports, an LCD controller with touch support, multiple CAN and UART interfaces, and a low-power real-time clock domain. The 500 MHz Cortex-A5 delivers roughly 1.4 DMIPS/MHz of integer performance, sufficient for Linux graphical user interfaces and real-time control loops. The Vybrid architecture pairs the Cortex-A5 with a separate Cortex-M4 microcontroller-style core on higher-tier VF6xx devices, but the VF5xx line is single-core for cost-sensitive designs. The integrated L2 Ethernet switch eliminates external switch chips in gateway and HMI applications. Typical applications include industrial human-machine interfaces (HMIs), building automation gateways, smart energy and IoT edge nodes, point-of-sale terminals, and medical patient monitors. The combination of DDR3 support and an integrated display controller makes the part attractive for graphics-rich HMIs without an external companion GPU. A critical design consideration is PCB layout for the 364-ball LFBGA: a minimum 4-layer stack-up with continuous ground reference beneath the package is required to maintain signal integrity on the DDR3 interface. Engineers should also plan for the boot configuration pins, which select between quad-SPI flash, SD card, and UART bootstrap modes. This page synthesizes distributor pricing, drop-in alternatives within the Vybrid family, and practical design notes that go beyond the manufacturer datasheet, helping engineers shorten the BOM selection cycle and avoid common pitfalls.

詢價 聯絡我們
MVF60NN151CMK50 - Vybrid VF6xx Dual-Core 500MHz MPU | NXP
MVF60NN151CMK50

MVF60NN151CMK50 - Vybrid VF6xx Dual-Core 500MHz MPU | NXP

The NXP MVF60NN151CMK50 is a Vybrid VF6xx family heterogeneous dual-core microprocessor combining an ARM Cortex-A5 core running at 500 MHz with an ARM Cortex-M4 core running at 167 MHz, packaged in a 364-ball MAPBGA (LFBGA 17x17 mm). It is designed for industrial HMI, factory automation, and connected embedded applications where deterministic real-time control coexists with rich graphics and connectivity stacks. A microprocessor (MPU) in the Cortex-A class is a system-on-chip integrating a CPU core, memory controllers, and a wide peripheral set. Heterogeneous dual-core MPUs pair an application core (Cortex-A5, capable of running a high-level OS such as Linux or MQX) and a real-time microcontroller core (Cortex-M4) on the same silicon. This architecture belongs to the broader category of 32-bit microprocessors > microcontrollers > embedded processors > semiconductors, enabling developers to consolidate what would otherwise require two separate ICs. Key features of the MVF60NN151CMK50 include dual 10/100 Ethernet controllers with integrated L2 switch, dual USB 2.0 OTG controllers with PHY, up to 1.5 MB of on-chip SRAM, a rich display controller (LCD), and a suite of communication peripherals including UART, SPI, I2C, CAN, and I2S. The device is offered without on-chip security (anti-clone/anti-tamper/secure boot) features in this specific -NN151 ordering code. The architecture uses ARM NEON-compatible media processing on the A5 side and single-precision FPU plus DSP extensions on the M4 side, allowing concurrent execution of an HMI graphics stack on A5 and deterministic motor/IO control on M4 without context-switch jitter. The integrated L2-switch Ethernet enables daisy-chained industrial topologies without an external switch IC. Typical applications include industrial HMI panels, programmable logic controllers (PLC), building automation gateways, smart energy concentrators, and medical patient-monitoring displays. Its dual-core split is well suited to systems where Linux-based graphics and a deterministic real-time control loop must share the same board. When designing with this part, ensure the PCB supports the 17x17 mm BGA footprint with proper microvia stack-ups, and allocate sufficient decoupling (10 uF + 100 nF per supply domain) close to each BGA quadrant. Validate DDR3L trace lengths against the JEDEC DDR3L fly-by topology recommended in the NXP hardware design guide. This page synthesizes distributor pricing, package-level cross-references within the Vybrid VF6xx family, and practical PCB/thermal notes that go beyond the manufacturer datasheet summary. Engineers comparing MVF60NN151CMK50 against MVF30 or MVF50 variants will find a parameter-by-parameter table and design notes specific to the 364-MAPBGA footprint.

詢價 聯絡我們
MVF60NS151CMK50 - Vybrid VF6xx Dual-Core A5/M4 MPU, 500MHz | NXP
MVF60NS151CMK50

MVF60NS151CMK50 - Vybrid VF6xx Dual-Core A5/M4 MPU, 500MHz | NXP

The NXP Semiconductors MVF60NS151CMK50 is a heterogeneous dual-core microprocessor from the Vybrid VF6xx family, integrating an ARM Cortex-A5 core at up to 500 MHz and an ARM Cortex-M4 core at up to 167 MHz in a 364-pin LFBGA (17x17 mm) package. The device is positioned as a secure, industrial-grade MPU combining an applications processor class core with a real-time microcontroller class core on a single die. An MPU (Microprocessor Unit) is an integrated processor that integrates CPU cores, memory interfaces, and a wide set of peripherals into a single IC. The MVF60NS151CMK50 belongs to the wider category hierarchy: microprocessor -> processor -> system-on-chip -> semiconductor. The Vybrid platform combines application processing with deterministic real-time control, enabling a single-chip architecture for HMI, connectivity, and motor or sensor control in industrial and IoT systems. Key features of the MVF60NS151CMK50 include up to 1.5 MB of on-chip SRAM, dual USB 2.0 OTG controllers with integrated PHY, dual 10/100 Ethernet controllers with an L2 switch, and a rich suite of communication, connectivity, and HMI interfaces. Hardware security features include anti-clone, anti-tamper, secure boot, and cryptography acceleration. The heterogeneous core pairing allows Linux or a high-level OS on the A5 while the M4 handles real-time tasks under a real-time OS or bare-metal firmware. The device is fabricated on a low-power CMOS process and supports industrial temperature ranges. Multiple power domains enable portions of the SoC to be powered down independently, optimizing energy efficiency for battery-backed or always-on industrial nodes. The architecture targets applications where deterministic latency for control loops is as critical as GUI, networking, and security performance. Typical applications include industrial HMI panels, building automation controllers, smart energy gateways, factory automation PLCs, point-of-sale terminals, and medical patient monitoring equipment. The combination of dual Ethernet, dual USB, and a TFT LCD controller makes the part especially suited for connected operator-interface terminals. Designers should plan PCB layout for a 17x17 mm BGA with 0.8 mm pitch, allocate sufficient decoupling, and review NXP reference designs for power-sequencing of the multiple voltage rails required by the A5 and M4 cores. This page synthesizes distributor pricing, drop-in alternatives from the Vybrid family, and PCB/thermal design guidance beyond what is printed in the manufacturer datasheet.

詢價 聯絡我們
MVF60NS151CMK50551 - Vybrid F 32-bit MPU, ARM Cortex-A5/M4 | NXP
MVF60NS151CMK50551

MVF60NS151CMK50551 - Vybrid F 32-bit MPU, ARM Cortex-A5/M4 | NXP

The NXP Semiconductors MVF60NS151CMK50551 is a heterogeneous dual-core 32-bit microprocessor from the Vybrid VF6xx family, combining an ARM Cortex-A5 core running at 500 MHz with an ARM Cortex-M4 core running at 167 MHz in a single 364-pin MAPBGA package. It is part of NXP's Vybrid F series, targeting industrial HMI, factory automation, and connected IoT gateways that demand both rich OS-driven graphics and deterministic real-time control on a single die. A microprocessor (MPU) is a system-on-chip that integrates a CPU, memory interfaces, and a wide range of peripherals. Heterogeneous dual-core MPUs like the Vybrid VF6xx pair an application-class core (Cortex-A5) for Linux/RTOS GUI stacks with a microcontroller-class core (Cortex-M4) for low-latency motor control, sensor fusion, and safety routines. This architecture reduces board area, BOM cost, and inter-IC latency versus using two separate processors with shared buses. Key features include dual USB 2.0 OTG controllers with integrated PHY, dual 10/100 Ethernet MACs for redundant networking, a TFT/LCD controller for direct display attachment, hardware encryption accelerators, and a 32-channel DMA engine. The device integrates 1.5 MB of on-chip SRAM and supports external DDR3/LPDDR2 memory through a 16-bit interface. Industrial temperature grade operation from -40C to +105C makes it suitable for factory floor deployment. Typical applications include industrial human-machine interfaces (HMIs), programmable logic controllers (PLCs), building automation gateways, point-of-sale terminals, and connected medical devices. The M4 core's deterministic interrupt response is well-matched to motor control loops while the A5 core handles touch-screen GUI, OPC-UA, and Ethernet/IP protocol stacks. When designing with this part, allocate the 364-ball MAPBGA escape routing carefully and provide a 4-layer or higher PCB stack-up to break out the LFBGA's 0.8 mm pitch balls. Ensure the DDR3/LPDDR2 interface follows the JEDEC layout rules for length-matched, impedance-controlled traces.

詢價 聯絡我們
MVF61NN151CMK50 - Vybrid VF6xx Dual-Core MPU 500MHz | NXP
MVF61NN151CMK50

MVF61NN151CMK50 - Vybrid VF6xx Dual-Core MPU 500MHz | NXP

The NXP Semiconductors MVF61NN151CMK50 is a heterogeneous dual-core microprocessor (MPU) from the Vybrid VF6xx family that combines an ARM Cortex-A5 application core running at 500 MHz with an ARM Cortex-M4 real-time core running at 167 MHz, packaged in a 364-ball LFBGA (17x17 mm). The device integrates up to 1.5 MB of on-chip SRAM, dual 10/100 Ethernet controllers with L2 switch, dual USB 2.0 OTG controllers with integrated PHY, and a rich suite of communication peripherals (CAN, SPI, I2C, UART, I2S, SDIO). A microprocessor (MPU) is an integrated circuit that contains a CPU, memory, and peripherals on a single die. Heterogeneous multicore MPUs pair a high-performance application core (here Cortex-A5, capable of running a full Linux or RTOS stack) with a deterministic real-time core (Cortex-M4, used for time-critical motor control or sensor acquisition). The Vybrid family sits in the hierarchy: MPU -> ARM Cortex -> application processor -> embedded system-on-chip. This dual-core architecture lets one core handle HMI/connectivity while the other handles hard-real-time I/O, eliminating task scheduling jitter. Key features include 32-bit data path, anti-clone / anti-tamper security with secure boot, on-chip LCD controller, NEON media engine on the A5 core, single-precision FPU on the M4 core, and industrial-grade -40C to +85C operating temperature. The 364-LFBGA package provides the high-pin-count interconnect needed for dual Ethernet, dual USB, and parallel external memory bus interfaces. Typical applications include industrial HMI panels, building automation controllers, smart energy gateways, point-of-sale terminals, and factory-automation PLCs. The Cortex-M4 sub-system is well suited to BLDC motor control loops, while the A5 runs the Linux user interface and networking stacks. Security features such as secure boot and tamper detection target connected IoT infrastructure. Designers should note that the 1.5 MB on-chip SRAM reduces external memory accesses for many workloads, but the external memory bus (EBI/EMI) is still required for bulk storage and LCD framebuffer. Power sequencing of the multiple internal rails (core, I/O, PHY, ADC) must follow the reference manual; failure to do so risks latch-up during cold-start.

詢價 聯絡我們
MVF62NN151CMK40 - Vybrid VF6xx Dual-Core MPU, ARM A5+M4 | NXP
MVF62NN151CMK40

MVF62NN151CMK40 - Vybrid VF6xx Dual-Core MPU, ARM A5+M4 | NXP

The NXP Semiconductors MVF62NN151CMK40 is a heterogeneous dual-core 32-bit microprocessor from the Vybrid VF6xx family, integrating an ARM Cortex-A5 core running up to 400 MHz with an ARM Cortex-M4 core running up to 266 MHz (per the official NXP product page). It is housed in a 364-ball MAPBGA package (17x17 mm, 0.8 mm pitch) and operates from a 3.3 V I/O supply with a 1.23 V internal core voltage. The device belongs to the VFxxx F sub-series and is targeted at industrial HMI, factory automation, and connected embedded applications that benefit from asymmetric multiprocessing. What is a heterogeneous dual-core MPU? A heterogeneous multiprocessor unit (MPU) is a system-on-chip that combines two architecturally different processor cores on the same silicon. The high-performance Cortex-A5 typically runs a rich operating system (Linux, MQX, or similar) while the Cortex-M4 handles real-time deterministic tasks such as motor control or sensor polling. This topology replaces traditional ASIC+MCU designs, reducing board area, BOM, and inter-IC communication latency. Vybrid sits in the MPU -> application processor -> embedded SoC taxonomy, bridging the gap between microcontrollers (single-core deterministic) and full application processors (high-MHz Linux-class). Key features include dual-core asymmetric processing (A5 + M4), dual USB 2.0 OTG controllers with integrated PHY, dual 10/100 Ethernet controllers with L2 switch acceleration, a 1.5 MB on-chip SRAM block, and a wide range of connectivity peripherals (UART, SPI, I2C, CAN, I2S). The device is offered in a 364-ball MAPBGA (17x17) for high-density industrial designs, with operating temperature and AEC-Q100 grade specific to the variant ordering code. The A5 core includes an NEON media engine and a single-precision FPU, while the M4 core adds a similar FPU plus DSP extensions. The platform supports up to 1.5 MB of on-chip SRAM, configurable L2 cache, and DDR2/DDR3 external memory controllers. Multiple on-chip timer blocks, watchdog timers, and a rich interrupt controller (NVIC) serve deterministic real-time tasks delegated to the M4. Typical applications include industrial HMI panels, building automation gateways, factory automation controllers, motor drive supervisors, smart energy concentrators, and medical patient monitors. The dual-Ethernet and dual-USB OTG capability enables redundant fieldbus and device connectivity in industrial networking designs. When designing with this MPU, ensure the DDR memory layout uses matched-trace routing and proper decoupling; the heterogeneous topology also requires careful pin-mux assignment so that high-speed peripherals do not conflict with general-purpose I/O. A robust bootloader strategy is recommended to allow in-field firmware updates across both cores. This page synthesizes distributor pricing, drop-in alternative MPNs, and practical design notes not found in a single manufacturer datasheet, giving engineers a single reference for sourcing the Vybrid VF6xx dual-core MPU.

詢價 聯絡我們
MX29F400CBTI-70G - 4Mbit 5V Parallel NOR Flash, 70ns, 48-TSOP | Macronix
MX29F400CBTI-70G

MX29F400CBTI-70G - 4Mbit 5V Parallel NOR Flash, 70ns, 48-TSOP | Macronix

The Macronix MX29F400CBTI-70G is a 4-Mbit CMOS single-voltage 5V-only boot-sector Flash memory organized as 512K x 8 (byte mode) or 256K x 16 (word mode), offered in a 48-pin TSOP Type I package with 70 ns access time. It features a Bottom Boot Sector architecture with one 16-Kbyte, two 8-Kbyte, one 32-Kbyte, and three 64-Kbyte sectors, enabling flexible firmware storage and in-system updates. The device operates from a single 4.5V to 5.5V supply and supports parallel x8/x16 data interfaces with standard JEDEC command-set compatibility. A NOR Flash memory is a non-volatile storage class that executes code directly from the array (execute-in-place, XiP), making it the technology of choice for boot ROMs and firmware storage in embedded systems. Within the memory hierarchy, NOR Flash sits above NAND Flash for random-access reliability and above SRAM/DRAM for non-volatility; it forms the persistent storage tier between battery-backed SRAM and high-density NAND. The MX29F400C series implements the Common Flash Memory Interface (CFI) for device identification, and the bottom-boot layout places small parameter sectors at low addresses - the most common configuration for PC BIOS and bootloader storage where small early-write sectors speed up boot code updates. Key features include 70 ns maximum access time, sector-erase granularity (16 KB / 8 KB / 32 KB / 64 KB), 100,000 erase cycles per sector endurance, and a JEDEC-standard command set for byte-program and sector/chip erase operations. The device includes hardware sector-protection via the WP#/ACC pin and a hardware reset (RP#) input for safe in-system resets. Embedded algorithms manage program and erase internally, freeing the host controller from timing state machines. The MX29F400CBTI-70G uses a NOR-cell array with hot-electron injection programming and Fowler-Nordheim tunneling for erase, providing reliable 5V-only operation without the 12V VPP required by older boot-sector Flash. The architecture supports single-cycle word/byte reads, with output enable control for bus sharing and a ready/busy (RY/BY#) output for hardware polling of internal algorithm completion. Typical applications include PC BIOS ROMs, set-top box boot loaders, networking equipment firmware, industrial control firmware, automotive infotainment boot code, and printer/copier controller firmware. The bottom-boot sector map is preferred when the bootloader resides at the lowest flash addresses and only the small 16K/8K boot sectors need frequent updates. When designing with this part, observe the recommended decoupling (0.1 uF ceramic at VCC) and route the 48-pin TSOP signals with matched trace lengths for the byte/word data bus. Note that this part is in production but increasingly replaced by SPI NOR devices in new designs - verify the 5V supply and parallel-bus requirement match your system before selection. This page synthesizes distributor pricing, drop-in alternatives, sector-map details, and practical design notes not found in the manufacturer datasheet alone.

詢價 聯絡我們
MX30LF1G08AA - 1Gb 3V SLC NAND Flash, Parallel, 48-TSOP | Macronix
MX30LF1G08AA

MX30LF1G08AA - 1Gb 3V SLC NAND Flash, Parallel, 48-TSOP | Macronix

The Macronix MX30LF1G08AA is a 1 Gbit (128M x 8) SLC NAND Flash memory device organized as a parallel interface, supplied in a 48-pin TSOP-I package and operating from a single 3.3 V rail (2.7 V to 3.6 V). It offers 25 ns / 30 ns asynchronous access time and is fully compliant with the ONFI 1.0 standard, which simplifies host controller bring-up and software portability across compatible controllers. The part is targeted at low-density, high-reliability code- and data-storage applications. A NAND Flash memory is a non-volatile storage technology that stores data as charge on floating-gate MOSFET cells arranged in pages and blocks. SLC (Single-Level Cell) NAND stores one bit per cell, which trades density for ten-times-higher endurance and lower bit-error rate than MLC or TLC counterparts. The NAND hierarchy sits within the broader non-volatile memory (NVM) family alongside NOR Flash, EEPROM, and emerging storage-class memories. In the system hierarchy it bridges volatile DRAM (working space, runtime) and the storage subsystem, used typically to hold bootloaders, operating-system images, and large data logs. Key features include a multiplexed 8-bit Command/Address/Data I/O bus (IO7-IO0), hardware write protect, chip enable (/CE), address latch enable (ALE), command latch enable (CLE), and ready/busy (/R/B) handshaking for standard NAND controllers. Page size is 2 Kbytes (plus 64 bytes spare) with a 128 Kbyte block erase granularity, supporting typical program/erase cycling of 100 K cycles per block and 10-year data retention. The 48-TSOP-I footprint is the industry-standard pinout for 8-bit parallel NAND. Architecturally, the MX30LF1G08AA uses a charge-trap/standard floating-gate NAND array with on-chip page buffers, an internal charge pump for program/erase voltages, and an ECC-friendly interface. The ONFI 1.0 parameter page exposes timing and geometry to the host so the controller can self-configure, enabling drop-in interoperability with reference Linux and U-Boot NAND stacks. Typical applications include industrial HMI panels, automotive infotainment boot media, networking equipment firmware storage, set-top box operating system images, point-of-sale terminals, and data loggers. The wide 2.7 V to 3.6 V supply range tolerates noisy industrial 3.3 V rails, while the 48-TSOP-I footprint mates with through-hole or socketed PCB layouts for easy prototyping. A key design consideration is ECC: every 528-byte sector read should be protected with at least 1-bit-per-512-bytes BCH or Hamming ECC in the host controller to meet typical industrial retention targets. Designers should also confirm the controller supports the 2 Kbyte page size; legacy controllers expecting 512-byte pages will require a bridge or a different NAND generation. This page synthesizes distributor pricing, drop-in alternatives (Macronix migration parts and cross-brand equivalents sourced from the Macronix cross-reference application notes), and practical design notes not found in the manufacturer datasheet alone.

詢價 聯絡我們
MX30LF1G18AC-TI-T - 1Gbit 3V SLC NAND Flash, TSOP-48 | Macronix
MX30LF1G18AC-TI-T

MX30LF1G18AC-TI-T - 1Gbit 3V SLC NAND Flash, TSOP-48 | Macronix

The Macronix MX30LF1G18AC-TI-T is a 1 Gbit (128M x 8) 3V SLC NAND Flash memory organized as 128M x 8 bits with 20 ns asynchronous parallel interface access time, housed in a 48-pin TSOP-I package with 4-bit ECC requirement. It operates from a single 2.7V to 3.6V VCC supply, supports a 20 ns tRC cycle time, and is compliant with the ONFI 1.0 specification for NAND interface interoperability. An SLC (Single-Level Cell) NAND Flash is a non-volatile memory that stores one bit per cell, giving it higher endurance (typically 100k P/E cycles), faster write speeds, and longer data retention than MLC/TLC counterparts. SLC NAND sits within the broader taxonomy of non-volatile memory -> flash memory -> NAND flash -> SLC NAND -> boot/storage media. It is commonly used for code storage, boot media, and industrial data logging where reliability over bit density matters. Key features include an internal 1K+64-byte page architecture with 64-byte spare area, multi-plane operation for higher throughput, hardware block protection (PT pin) with internal weak pull-down, and support for standard ONFI command set including read, program, erase, and block protection. The 4-bit ECC requirement per 512-byte sector enables robust error correction in demanding environments. The architecture uses a charge-trap floating gate cell technology, and the device supports dual CE operations, status register readback, and ID page read for unique device identification. Sequential read throughput scales with the bus width and ONFI timing mode selected. Typical applications include industrial embedded systems, automotive infotainment boot media, networking equipment firmware storage, point-of-sale terminals, and factory automation controllers requiring long-term reliable non-volatile code storage. Design consideration: ensure the host controller supports 4-bit ECC hardware engine to handle the 4-bit ECC requirement per 512-byte page, and respect the WP and PT pin pull-down behavior during power-on to avoid unintended protection lock. This page synthesizes distributor pricing, drop-in compatible SLC NAND alternatives, and practical design notes not consolidated in any single manufacturer datasheet.

詢價 聯絡我們
MX30LF1G18AC-TJ-TR - 1Gbit SLC NAND Flash 3V TSOP-48 | Macronix
MX30LF1G18AC-TJ-TR

MX30LF1G18AC-TJ-TR - 1Gbit SLC NAND Flash 3V TSOP-48 | Macronix

The Macronix MX30LF1G18AC-TJ-TR is a 1 Gbit (128M x 8) Single-Level Cell (SLC) NAND Flash memory operating from a single 2.7V to 3.6V supply and housed in a 48-pin TSOP-I (TJ) package. According to the Macronix MX30LF1G18AC datasheet, the device offers a 20 ns asynchronous page read access time, a 25 us first-byte cache read latency, and ONFI 1.0 compatibility for standardized NAND command sets. The part requires 4-bit ECC per 528-byte sector for reliable read endurance across 100,000 program/erase cycles. A NAND Flash memory is a non-volatile storage technology that retains data without power by storing charge on a floating-gate transistor array organized as pages and blocks. SLC NAND stores one bit per cell, giving it higher endurance, faster write speeds, and lower bit error rates than MLC or TLC NAND. In the broader taxonomy: NAND Flash -> non-volatile memory -> flash memory -> semiconductor memory IC. The MX30LF1G18AC belongs to Macronix's MX30LF 3V SLC NAND family, optimized for industrial and embedded designs that demand high reliability under extended temperature conditions. Key differentiating features of the MX30LF1G18AC include an internal data register for cache read operation, a hardware-based WP# pin for write protection, and a multi-plane page program architecture supporting up to 4-bit ECC. The device supports 2K + 64 byte pages and 128K + 4K byte blocks, with sequential read throughput of 20 ns per byte (50 MB/s). It also supports the ONFI Parameter Page read for standardized software driver support across operating systems. Technical architecture: The MX30LF1G18AC uses a charge-trap/standard floating-gate cell array manufactured on a mature CMOS process, paired with an on-chip charge pump that generates the high voltages required for program and erase operations. An internal data register (1 page = 2K + 64 bytes) acts as a buffer between the NAND cell array and the external I/O bus, enabling cache read modes that improve effective throughput. The controller logic implements ONFI 1.0 standard commands plus Macronix-specific extensions for unique features such as the Program Toggle (PT) function on pin 38. Typical applications include industrial control system firmware storage, automotive infotainment and telematics data logging, networking equipment boot and configuration storage, and embedded Linux/ RTOS file system media (JFFS2, UBI/UBIFS, YAFFS). The combination of 1 Gbit density and ONFI compliance makes it well-suited as a removable boot medium in set-top boxes and routers. Design consideration: Always provide 4-bit ECC per 528-byte sector using the host controller or FPGA logic; the MX30LF1G18AC does not include an internal ECC engine. Bad-block management must be implemented in software by scanning the factory-marked bad-block table at first power-up. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

詢價 聯絡我們
MX30LF1G18AC-XKR-T - 1Gb SLC NAND Flash, 3V, BGA-63 | Macronix
MX30LF1G18AC-XKR-T

MX30LF1G18AC-XKR-T - 1Gb SLC NAND Flash, 3V, BGA-63 | Macronix

The Macronix MX30LF1G18AC-XKR-T is a 1 Gbit (128 MB) Single-Level Cell (SLC) NAND Flash memory in a 63-ball VFBGA (9 x 11 mm) package, supplied on tape-and-reel, qualified to the automotive +105 C operating temperature grade. The device operates from a 3 V (2.7 V to 3.6 V) supply, supports an 8-bit parallel asynchronous data interface with a 20 ns tRC access time, and offers 4-bit ECC capability. The XK ball-map variant is targeted at industrial and automotive embedded systems requiring a compact BGA footprint, in contrast with the TI (48-pin TSOP) sibling of the same die. What is SLC NAND Flash? SLC (Single-Level Cell) NAND is a non-volatile memory technology that stores one bit per cell, giving it the highest endurance (typically 100k P/E cycles per block), the lowest bit-error rate, and the fastest write speeds of any NAND family. Within the broader hierarchy, SLC NAND sits below DRAM in the memory pyramid: faster than NOR for large-block writes, denser and cheaper per bit than NOR, and far more reliable than MLC/TLC/QLC NAND at the cost of lower density per die. The MX30LF1G18AC-XKR-T therefore fills the niche where designers need MLC-class capacity but cannot tolerate MLC-level endurance or error-rate penalties. Key differentiating features include ONFI 1.0 command-set compliance, a hardware PT (Protection) pin on ball G5 that block-protects the entire chip at power-on, internal 4-bit ECC engines, and an extended -40 C to +105 C automotive temperature range. The 63-ball VFBGA package keeps board area under 100 mm^2, while the asynchronous interface allows simple MCU/FPGA glue logic without requiring an ONFI controller IP block. Architecturally, the MX30LF1G18AC implements a single 1 Gbit die organized as 1024 blocks, each containing 64 pages of 2112 bytes (2048 data + 64 spare). Read is page-granular (typically 25 us), program is page-driven (~300 us), and erase is block-level (typically 2 ms). The ONFI 1.0 command set ensures the part can be driven by any standard NAND controller, including Linux MTD drivers and bare-metal bootloaders. Typical applications include automotive infotainment and instrument-cluster boot/data storage, industrial HMI panel firmware, point-of-sale terminals, IoT gateways requiring reliable OTA update storage, and medical devices where long-term data retention (10-year JEDEC spec) outweighs density requirements. When designing with this device, route the BGA balls to a minimum 4-layer PCB with continuous GND plane under the package to maintain signal integrity on the 8-bit parallel bus, and budget the I/O capacitance (typically 10 pF) when calculating read-window margins. Always issue the PT-protection release command sequence before programming in production, or leave PT floating (the internal weak pull-down disables protection). This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

詢價 聯絡我們
MX30LF1GE8AB-TI-T - 1Gbit SLC NAND Flash, x8, 3V, TSOP-48 | Macronix
MX30LF1GE8AB-TI-T

MX30LF1GE8AB-TI-T - 1Gbit SLC NAND Flash, x8, 3V, TSOP-48 | Macronix

The Macronix MX30LF1GE8AB-TI-T is a 1 Gbit (128M x 8) SLC NAND Flash memory IC with a parallel asynchronous interface and ONFI 1.0 compliance, supplied in a 48-pin TSOP package and rated for the industrial temperature range (-40C to +85C). It supports a 2.7V to 3.6V single supply, a 2048 + 64-byte page size, a 128K + 4K-byte block size, 25 us array-to-register latency, 20 ns sequential read access, page program, cache read, and a 64-byte user-redundancy area for ECC. An SLC NAND Flash is a type of non-volatile memory that stores one bit per cell, delivering higher endurance (typically 100k P/E cycles per block), faster write performance, and longer data retention than MLC or TLC NAND, at the cost of lower density per die. NAND Flash sits below NOR Flash and DRAM in the memory hierarchy and is commonly used for bulk data and code storage behind a filesystem or controller. The MX30LF1GE8AB belongs to the 3V SLC NAND family, which is widely used in industrial, networking, and embedded designs where reliability and predictable write latency matter more than raw bit density. Key features include ONFI 1.0 parameter block compliance for controller portability, multiplexed command/address/data I/O to reduce pin count, hardware-ready ECC with 64 spare bytes per page, industrial-grade operating range, and a standard TSOP-48 footprint shared with most 1Gbit parallel NAND parts. Page-program and block-erase operations follow standard ONFI command sets, allowing direct reuse of existing low-level drivers. The wide 2.7V-3.6V supply range simplifies designs migrating from 3.3V NOR Flash or PSRAM. Typical applications include industrial data logging, networking equipment firmware storage, IoT gateways, automotive infotainment code storage, set-top box boot + OS, and POS terminals. The 1Gbit linear latency of 25 us array-to-register and 20 ns sequential read make it a strong fit for systems that boot from NAND with a small on-chip or external ROM bootloader. When designing with this device, follow ONFI timing diagrams closely: honor tR/tPROG/tBERS delays, drive the WP pin low during power transitions to prevent spurious program/erase, and place the CE# pull-up resistor close to the NAND to keep the bus idle during controller reset. This page synthesizes distributor pricing, drop-in alternatives, ONFI timing notes, and ECC design guidance not bundled in the manufacturer datasheet, so engineers can evaluate a board-level replacement faster.

詢價 聯絡我們
MX30LF1GE8AB-TI-TR - 1Gbit 3V SLC NAND Flash, x8, TSOP-48 | Macronix
MX30LF1GE8AB-TI-TR

MX30LF1GE8AB-TI-TR - 1Gbit 3V SLC NAND Flash, x8, TSOP-48 | Macronix

The Macronix MX30LF1GE8AB-TI-TR is a 1 Gbit (128 M x 8) 3 V Single-Level Cell (SLC) parallel NAND Flash memory device housed in a 48-pin TSOP-I (Type I) package, supplied on tape-and-reel. It is ONFI 1.0 compliant, supports a parallel asynchronous interface with 20 ns / 25 ns access time depending on grade, and operates from a single 2.7 V to 3.6 V supply with an ECC-Free architecture intended for use with an external host controller. A NAND Flash is a non-volatile memory that stores data as charge on floating-gate cells arranged in pages and blocks, accessed through a command-driven protocol over a multiplexed 8-bit I/O bus. SLC NAND stores one bit per cell, offering the highest endurance and reliability within the NAND family (which itself is a class of non-volatile memory -> flash memory -> semiconductor memory -> IC). Compared with NOR flash, NAND provides higher density at lower cost-per-bit and faster write/erase, but requires sequential access and external ECC for data integrity in mission-critical applications. Key features include a 2112-byte page size (2048 + 64 spare), 64 pages per block (128 KB + 4 KB spare), 1024 blocks, internal data-move / copy-back operations, hardware-ready/busy (R/B#) signaling, and command-set compatibility with the ONFI 1.0 baseline. ECC-Free means error correction is handled by the host, giving designers freedom to choose ECC strength (typically BCH or Hamming). The TSOP-I 48-pin package is the industry-standard footprint shared by most 1 Gbit to 4 Gbit parallel NAND parts. The MX30LF1GE8AB architecture uses a 2-plane array that enables interleaved page program and block erase between planes for higher throughput. Plane interleaving can effectively double sequential write bandwidth by overlapping tPROG of one plane with tR of the other. Designers should size VCC decoupling (1 uF + 100 nF) close to the VCC/VSS pins and respect the 100 us R/B# power-on delay per the Macronix datasheet revision v1.3. Typical applications include embedded Linux/OS boot + mass storage in industrial gateways, set-top box and smart-TV storage, automotive infotainment (non-safety), networking equipment logging, and IoT edge devices that need reliable code + data storage at 3 V. Designers migrating from the older MX30LF1G08AA should review Macronix application note AN0366V1, as the MX30LF1GE8AB has a longer Device ID and slightly longer tR. When designing in this part, allow 1.5 us tRST after power-up before issuing the reset (0xFF) command. The R/B# pin is open-drain and requires an external pull-up. For long-term data retention, program/erase endurance is rated at 100 K cycles per block typical, with 10-year data retention. This page synthesizes distributor pricing, drop-in and same-family alternatives, and practical design notes not found in the manufacturer datasheet alone.

詢價 聯絡我們
MX30LF1GE8AB-XKI-TR - 1Gbit 3V SLC NAND Flash, 63-VFBGA | Macronix
MX30LF1GE8AB-XKI-TR

MX30LF1GE8AB-XKI-TR - 1Gbit 3V SLC NAND Flash, 63-VFBGA | Macronix

The Macronix MX30LF1GE8AB-XKI-TR is a 1 Gbit (128M x 8) 3V SLC NAND Flash memory organized as parallel x8 in a 63-ball VFBGA (9x11 mm) package. It supports an asynchronous parallel interface with a 20 ns initial access time and operates from a single 2.7V to 3.6V supply, with a typical active current of 15 mA. The device is ONFI 1.0 compliant and is supplied in Tape & Reel packaging for high-volume SMT production. A NAND Flash memory is a non-volatile storage technology that retains data without power, using floating-gate transistors arranged in NAND string blocks and pages. It sits in the hierarchy between raw NOR (byte-addressable, fast read) and managed NAND/eMMC (controller-integrated). SLC (Single-Level Cell) NAND stores one bit per cell, giving it the highest endurance and reliability tier in the NAND family - typically 100K P/E cycles per block versus 3K-10K for MLC/TLC - making it preferred for industrial code storage, boot media, and high-write workloads where MLC/TLC would wear out quickly. The MX30LF1GE8AB family features a 2,112-byte page (2,048 bytes data + 64 bytes spare for bad-block marks and ECC), 64 pages per block, and 1,024 blocks per plane. Program and erase times are 1 ms (typical) page-program and 2 ms block-erase, while page-read cycle time is on the order of 25 ns. ECC handling is left to the host controller, which is why this family is labelled ECC-Free. Typical applications include industrial embedded systems, networking equipment, set-top boxes, printers, and automotive infotainment where 1 Gbit of non-volatile code or data storage is needed with parallel access. The wide -40C to +85C operating range covers industrial environments, and the small 9x11 mm VFBGA footprint suits space-constrained PCB designs. When migrating a design to the MX30LF1GE8AB, ensure the host controller supports the longer Device ID and tR random read cycle compared with the legacy MX30LF1G08AA, per Macronix application note AN0366. Add external ECC in the controller firmware, since this part ships ECC-Free. This page synthesizes distributor pricing, drop-in alternatives in the same 63-VFBGA footprint, and practical design notes not collected in the manufacturer datasheet.

詢價 聯絡我們
MX30LF4G18AC-TI-T - 4Gbit SLC NAND Flash, 3V, TSOP-48 | Macronix
MX30LF4G18AC-TI-T

MX30LF4G18AC-TI-T - 4Gbit SLC NAND Flash, 3V, TSOP-48 | Macronix

The Macronix MX30LF4G18AC-TI-T is a 4 Gbit SLC NAND Flash memory IC organized as 512M x 8 bits, housed in a 48-pin TSOP-I (12 mm x 20 mm) package. Operating from a 2.7V to 3.6V single supply with a 20 ns random access time, it delivers high endurance and reliability for code and data storage in embedded designs. The part supports a parallel asynchronous interface compliant with the ONFI 1.0 standard and is offered in a -40C to +85C industrial temperature grade. An SLC (Single-Level Cell) NAND Flash is a non-volatile memory technology that stores one bit per memory cell, providing higher write endurance (typically 60k-100k P/E cycles), faster write performance, and lower bit error rates than MLC or TLC NAND. SLC NAND sits below raw NAND in the storage hierarchy - between NOR Flash (byte-addressable, slower write) and managed NAND (eMMC/UFS with built-in controllers). Because raw SLC NAND requires an external Flash controller (or FTL in software), it is favored in cost-sensitive, reliability-critical designs where the host MCU or ASIC already includes a NAND controller. Key features of the MX30LF4G18AC-TI-T include a 20 ns access time, ONFI 1.0 parameter page compatibility, 4-bit ECC requirement per 528-byte sector, 8-bit data bus, and a 10-year data retention rating. The device supports single-plane and dual-plane operations, hardware data protection via WP#, and a standard command set (read, program, erase, block management) consistent with the ONFI 1.0 specification. The wide temperature operating range (-40C to +85C) suits industrial and automotive-adjacent applications. At the architectural level, the device is organized into 4096 blocks of 128 KB plus spare area, with each page holding 2 KB + 64 B spare (x8 mode). Page program is typically 300 us and block erase around 2 ms, enabling deterministic write timing for industrial firmware updates and fast boot storage. The 4-bit ECC requirement means the system controller must implement a BCH or Reed-Solomon engine to correct raw bit errors before they exceed the ECC budget. Typical applications include industrial embedded Linux systems, automotive infotainment boot media, networking equipment firmware storage, factory automation controllers, and ruggedized IoT gateways that demand long-term reliability under wide temperature swings. When designing with raw NAND, ensure the host controller implements 4-bit ECC per 528-byte sector, plan for bad-block management in software, and reserve enough boot time for NAND initialization. The TSOP-48 footprint is widely supported by surface-mount assembly lines but requires careful PCB layout to keep the 8-bit parallel bus impedance-controlled for signal integrity at 20 ns access speeds. This page synthesizes distributor pricing, same-brand density/package variants, and practical ECC and layout design notes not consolidated in any single manufacturer or distributor source.

詢價 聯絡我們
MX30LF4G18AC-XKI-T - 4Gbit SLC NAND Flash 63-VFBGA | Macronix
MX30LF4G18AC-XKI-T

MX30LF4G18AC-XKI-T - 4Gbit SLC NAND Flash 63-VFBGA | Macronix

The Macronix MX30LF4G18AC-XKI-T is a 4 Gbit parallel SLC NAND Flash memory organized as 512M x 8 bits, housed in a 63-ball 9x11 mm VFBGA package (also known as 63-VFBGA / BGA-63). It operates from a single 3V supply (2.7V to 3.6V), supports ONFI 1.0 timing, and offers a 20 ns access time, making it well-suited for boot, code, and data storage in embedded designs. The -XKI suffix indicates the industrial operating-temperature grade of -40C to +85C, while the -T suffix denotes Tape & Reel packaging for high-volume SMT assembly. NAND Flash is a non-volatile storage technology where memory cells are arranged in strings and pages rather than as individually addressable bytes. SLC (Single-Level Cell) stores one bit per cell, giving higher endurance, faster write speeds, and better data retention than MLC/TLC alternatives. The MX30LF4G18AC belongs to Macronix's MX30LF family of 3V SLC NAND devices and uses an asynchronous parallel interface to a host controller. Within the broader taxonomy, it sits under Flash Memory -> Non-Volatile Memory -> Memory IC -> Semiconductor. Compared with NOR Flash, NAND provides higher density at lower cost-per-bit but requires a controller to manage bad blocks, wear leveling, and ECC, which is why this part mandates 4-bit ECC per 528 bytes. Key specifications include a 2,048-byte main page area plus a 64-byte spare area per page (2,112 bytes total), 64 pages per block, and an internal data buffer of 2,112 bytes for load and access. The device is divided into two planes, each composed of NAND strings of 32 serially connected cells, which enables interleaved page operations for higher throughput. ONFI 1.0 compliance guarantees standardized command sets, timing parameters, and feature registers across compliant hosts. Typical applications include embedded Linux/Android boot storage, solid-state drives (SSD) for SATA/USB bridges, automotive infotainment, set-top boxes, industrial gateways, and IoT edge nodes. Designers favor this Macronix SLC part where 100,000 P/E cycle endurance and 10-year data retention matter more than the highest densities available from MLC/TLC devices. When designing in the MX30LF4G18AC-XKI-T, allocate sufficient host-side ECC (4-bit per 528 bytes minimum), place a 0.1uF decoupling capacitor close to the VCC ball, and respect the 20 ns tRC/tWC timing budget. The 9x11 mm VFBGA footprint is compact, but its 0.8 mm pitch demands 4-layer PCB with microvia or laser-drilled vias for reliable manufacturing.

詢價 聯絡我們
MX30LF4G18AC-XKS-T - 4Gbit 3V SLC NAND Flash BGA-63 | Macronix
MX30LF4G18AC-XKS-T

MX30LF4G18AC-XKS-T - 4Gbit 3V SLC NAND Flash BGA-63 | Macronix

The Macronix MX30LF4G18AC-XKS-T is a 4 Gbit (512 M x 8) 3 V SLC NAND Flash memory in a 63-ball VFBGA (9 x 11 mm) package, qualified to +85C for automotive-grade applications. It features a parallel x8 interface with a typical 20 ns access time, 4-bit ECC requirement per 512 bytes, and ONFI 1.0 compliance for command-set interoperability. The device organizes 4 Gbits into two planes of 2,048-byte pages with 64 spare bytes each, totaling 2,112 bytes per page; the on-chip buffer matches the page size for load/program operations. An SLC (Single-Level Cell) NAND Flash is a non-volatile memory that stores one bit per cell, offering higher endurance, faster write speeds, and lower bit error rates than MLC/TLC NAND at the cost of lower density per die. SLC belongs to the broader NAND Flash family, which in turn is a subset of non-volatile memory technologies (Flash, EEPROM, FRAM, MRAM) used for code and data storage in embedded systems. SLC NAND's role in the memory hierarchy is to provide persistent, block-addressable storage between DRAM (volatile, fast) and serial NOR Flash (random-access, lower density), making it ideal for OS images, file systems, and data logging. Key features of the MX30LF4G18AC-XKS-T include a wide 2.7 V to 3.6 V single-supply operating range, 4-bit ECC per 528 bytes for robust data integrity, 100K program/erase cycles endurance per block, and 10-year data retention. The device supports standard NAND commands (Read, Program, Erase, Status) plus ONFI-defined parameter page reads, easing firmware development. Internal data-move and copy-back operations accelerate block management without external bus traffic. The architecture uses a two-plane structure with 64 pages of (2,048 + 64) bytes per plane, organized as two NAND strings of 32 series-connected cells. The 63-ball VFBGA footprint (9 x 11 mm) suits space-constrained designs, and the -XKS suffix denotes tape-and-reel packaging with an industrial/automotive +85C operating temperature grade. Designers should ensure 4-bit ECC is implemented in the host controller, as the device does not include an internal ECC engine. Typical applications include automotive infotainment and telematics, industrial gateways, IoT edge nodes, point-of-sale terminals, and firmware boot media. In automotive dashboards the part stores navigation maps and OS images; in IoT gateways it logs sensor telemetry. Compared with SPI NOR Flash of similar density, this SLC NAND delivers higher capacity at lower cost-per-bit but requires block-level management and ECC, increasing firmware complexity. The -XKS-T suffix adds tape-and-reel packaging for high-volume SMT assembly lines. When designing with this part, allocate one NAND controller pin set (ALE, CLE, WE#, RE#, CE#) and route I/O[7:0] as an 8-bit parallel bus. Place 0.1 uF decoupling near VCC balls and keep the 8-bit bus length-matched within 50 mils. The 4-bit ECC per 528 bytes must be generated by the host MCU/SoC; Macronix does not embed the ECC engine on this die.

詢價 聯絡我們
MX30LF4G28AB - 4Gbit SLC NAND Flash, 3V Parallel | Macronix
MX30LF4G28AB

MX30LF4G28AB - 4Gbit SLC NAND Flash, 3V Parallel | Macronix

The Macronix MX30LF4G28AB is a 4 Gbit (512M x 8) SLC NAND Flash memory with a parallel asynchronous interface, designed for low-density non-volatile storage in industrial, networking, and consumer embedded designs. It operates from a 2.7 V to 3.6 V supply and delivers 20 ns random access time in industry-standard 48-pin TSOP-I and 63-ball VFBGA packages. The device is ONFI 1.0 compliant, ensuring standardized command set, timing, and status register behavior for software portability across vendors. SLC (Single-Level Cell) NAND Flash is a non-volatile memory technology that stores one bit per memory cell, providing higher endurance (typically 60,000 to 100,000 program/erase cycles), faster write throughput, and longer data retention than MLC or TLC NAND. SLC NAND sits in the hierarchy: NAND Flash -> non-volatile memory -> memory IC -> semiconductor. It is commonly used where reliability, deterministic write performance, and wide-temperature operation outweigh the bit-density advantages of MLC/TLC parts. The MX30LF4G28AB divides its array into two planes, with 64 pages of (2,048+112) bytes per page, providing a 2,160-byte on-chip data register for page read, program, and cache operations. Key features include hardware data protection via the WP# pin, a Ready/Busy (R/B#) open-drain status output, ONFI-compliant unique ID read, and status register read. The page size of 2,048 bytes plus 112 bytes of spare area per page allows the host to apply ECC (typically BCH or Hamming) for bit-error correction without sacrificing user data capacity. The 48-TSOP-I package is backward-compatible with the 48-TSOP footprint used by many 2 Gb and 4 Gb parallel NAND parts, easing migration from older designs. Typical applications include industrial routers and gateways, factory automation controllers, automotive infotainment and instrument clusters, set-top box boot/media storage, point-of-sale terminals, and IoT edge devices. The wide -40 C to +85 C industrial operating range and ONFI compliance make it a fit for designs that require predictable behavior across temperature and across vendor sourcing. When designing with this device, allow margin for program/erase wear by implementing a wear-leveling algorithm and a robust ECC scheme (BCH-4 or stronger is recommended for 3x nm-class die). Decoupling: place a 0.1 uF and a 4.7 uF ceramic capacitor close to VCC/VCCQ, and route R/B# as an open-drain signal with a pull-up resistor to VCCQ to avoid in-rush current glitches. This page synthesizes distributor pricing, drop-in and cross-brand equivalents documented in Macronix application notes AN0280V2 (vs Spansion S34ML04G200) and AN0281V2 (vs Spansion S34ML04G100), and practical design notes not found in the manufacturer datasheet.

詢價 聯絡我們