產品(44,000+)

EFM32G200F64G-E-QFN32R - 64KB Flash ARM Cortex-M3 MCU | Silicon Labs
EFM32G200F64G-E-QFN32R

EFM32G200F64G-E-QFN32R - 64KB Flash ARM Cortex-M3 MCU | Silicon Labs

The Silicon Labs EFM32G200F64G-E-QFN32R is an ultra-low-power ARM Cortex-M3 Gecko microcontroller delivering 32 MHz performance with 64 KB Flash and 16 KB RAM in a 32-pin QFN (6x6) package, supplied on tape and reel for high-volume assembly. Key features include a single 1.98 V to 3.8 V supply rail, 24 digital I/O pins, 2 x 16-bit timers, integrated low-energy peripherals, hardware AES crypto accelerator (AES Excluded on this G-grade variant), 2-pin Serial Wire Debug, 1-pin Serial Wire Viewer, and a pre-programmed USB/UART bootloader. The Cortex-M3 core delivers 1.25 DMIPS/MHz with single-cycle multiplier and hardware MAC, while the autonomous peripheral reflex system allows I/O events to wake the MCU without CPU intervention. The EFM32G200F64G-E-QFN32R is built on the Gecko architecture from Energy Micro (acquired by Silicon Labs), which pioneered sub-microamp sleep current for battery-operated designs. Compared to a generic Cortex-M3, the Gecko adds an LESENSE block, on-chip op-amps, a 5V-tolerant GPIO structure, and an ultra-efficient Power-on Reset / Brown-Out Detector, giving designers a tightly integrated SoC rather than a raw MCU. Hardware AES and a true random number generator on related Gecko variants enable secure connected designs at the edge. Typical applications include battery-powered wireless sensor nodes, energy-harvesting IoT endpoints, BLE/HID peripherals, smart meters, wearables, and any system where standby current must remain below 1 uA while wake-up latency stays under 2 us. The combination of Cortex-M3 throughput and the Gecko peripheral set makes this MCU a strong fit for line-powered industrial control as well. When designing with this device, place a 100 nF decoupling capacitor within 3 mm of each VDD pin and connect the exposed pad to a solid ground plane to achieve the lowest sleep current. The integrated DC-DC converter requires an external 4.7 uH inductor and 4.7 uF bypass capacitor to operate efficiently above 10 mA loads.

詢價 聯絡我們
EFM32G210F128-QFN32 - 32MHz 128KB Cortex-M3 MCU | Silicon Labs
EFM32G210F128-QFN32

EFM32G210F128-QFN32 - 32MHz 128KB Cortex-M3 MCU | Silicon Labs

Silicon Labs EFM32G210F128-QFN32 is a 32-bit ARM Cortex-M3 microcontroller with a maximum clock speed of 32 MHz, 128 kB of embedded Flash memory, 16 kB of RAM, and 24 digital I/O pins, all housed in a 32-QFN package measuring 6 x 6 mm. It is designed for compact, energy-sensitive embedded systems that require efficient processing, fast wake-up behavior, and flexible low-power operation. A microcontroller is a programmable system-on-chip containing a processor core, nonvolatile program memory, volatile data memory, peripherals, and I/O. The EFM32G210 belongs to the EFM32 Gecko family, where Gecko microcontrollers form part of the broader 32-bit microcontroller, embedded processor, and semiconductor hierarchy. Its integrated memories and peripheral set reduce external component count while supporting standalone control, sensing, communications, and user-interface functions. The EFM32G210F128-QFN32 combines 128 kB of Flash with 16 kB of RAM and operates at up to 32 MHz. Silicon Labs highlights low-energy techniques, fast wake-up times, and energy-saving modes for battery-operated or duty-cycled systems. The device also includes two 16-bit timers and AES capability. Its 24 digital I/O pins provide connections for sensors, actuators, communications interfaces, and control logic in a compact board area. The ARM Cortex-M3 core provides a 32-bit RISC processing architecture and supports interrupt-driven embedded control. The Keil EFM32G210 datasheet identifies an optional Memory Protection Unit supporting as many as eight memory segments and a Wake-up Interrupt Controller for interrupts occurring while the processor sleeps. These features help protect memory regions and reduce response time when the MCU wakes from a low-energy state. Typical uses include IoT sensor nodes, compact industrial controls, wearable and wellness devices, building automation endpoints, low-power monitoring equipment, and connected accessories. The combination of local Flash and RAM permits firmware, state, and acquisition buffers to be handled locally, while the low-power architecture supports designs that spend substantial time in sleep rather than continuously executing code. PCB implementation should preserve the exposed-pad connection required by the 32-QFN package, maintain short return paths for sensitive signals, and provide suitable bypass capacitance near the supply pins. Verify the exact pin assignments, exposed-pad requirements, decoupling values, and programming interface in the manufacturer pinout and reference documentation before releasing a layout. This product record combines the manufacturer device description with package, memory, processor, timer, I/O, and power-system details, then adds application guidance and drop-in comparison options. It is designed to accelerate component selection, schematic planning, firmware bring-up, and PCB footprint verification for EFM32G210-based products.

詢價 聯絡我們
EFM32G222F128-QFP48 - 32MHz Cortex-M3 MCU | Silicon Labs
EFM32G222F128-QFP48

EFM32G222F128-QFP48 - 32MHz Cortex-M3 MCU | Silicon Labs

The Silicon Labs EFM32G222F128-QFP48 is a 32-bit ARM Cortex-M3 Gecko microcontroller operating up to 32 MHz, with 128 kB of Flash memory, 16 kB of RAM, and 37 digital I/O pins in a 48-pin TQFP package. Its 1.98 V to 3.8 V operating supply range and AES-capable design suit compact, energy-sensitive embedded systems. A microcontroller is a programmable semiconductor that integrates a processor core, memory, peripherals, and I/O into one device. Within the embedded-control hierarchy, an MCU executes firmware, samples sensors, controls actuators, and manages communications. The EFM32G222F128-QFP48 belongs to Silicon Labs' EFM32 Gecko family, combining an ARM Cortex-M3 processor with a low-power platform designed for fast wake-up operation and energy-saving modes. Principal device features include a 32 MHz maximum clock, 128 kB Flash for firmware, 16 kB SRAM for working data, and 37 digital I/O pins. The device also provides three 16-bit timers and AES hardware capability. These resources support event timing, motor or actuator control, secure data handling, and low-power sensor processing without requiring a separate external memory interface for typical firmware sizes. The EFM32G222F128-QFP48 combines a 1.98 V minimum and 3.8 V maximum supply operating range with a 32-bit Cortex-M3 core. Its Gecko low-energy architecture supports energy-sensitive products where average power, sleep current, and wake-up behavior influence battery life. Designers should account for decoupling, debug access, firmware size, peripheral sharing, and the available 37 digital I/O pins when allocating board resources. Typical uses include connected environmental sensors, compact industrial monitors, wearable accessories, building-control nodes, and low-power embedded instruments. The device is particularly suitable when local computation, deterministic timer resources, and modest communications requirements are needed. The 48-pin TQFP package also exposes more I/O than smaller dual in-line packages while remaining suitable for conventional surface-mount assembly. For a new board, follow the pin-description table in the Silicon Labs manufacturer datasheet when assigning signals, and preserve the documented debug and power pins. Place the required input, output, and decoupling capacitors close to their associated supply pins, keep switching and sensitive analog traces separated, and verify the chosen regulator can meet both load-transient and low-current sleep requirements. This page organizes the EFM32G222F128-QFP48 specifications, practical application guidance, verified source links, and pin-compatible Silicon Labs variants. It also highlights the memory, temperature-grade, and packaging considerations that engineers should check before approving a drop-in replacement for an existing 48-TQFP design.

詢價 聯絡我們
EFM32G222F32-QFP48 - 32MHz ARM Cortex-M3 MCU | Silicon Labs
EFM32G222F32-QFP48

EFM32G222F32-QFP48 - 32MHz ARM Cortex-M3 MCU | Silicon Labs

The Silicon Labs EFM32G222F32-QFP48 is a 32-bit ARM Cortex-M3 microcontroller operating up to 32 MHz, with 32 kB of Flash memory, 8 kB of RAM, and 37 digital I/O pins in a 48-pin TQFP package. It combines a low-power embedded platform with fast wake-up behavior, energy-saving modes, 3 × 16-bit timers, and flexible serial connectivity for embedded control designs. An MCU is a compact embedded computing component that integrates a processor core, memory, peripherals, and I/O into one device. The EFM32G222F32-QFP48 belongs to the EFM32 Gecko family and is intended for energy-sensitive applications where compact size, deterministic control, and low-power operation are important. Its Cortex-M3 architecture supports 32-bit processing while retaining a straightforward embedded software model. Key features include a maximum 32 MHz operating speed, 32 kB Flash organized as 32K × 8, 8 kB RAM, and 37 digital I/O pins. The device also provides three 16-bit timers and low-energy capabilities described by Silicon Labs as fast wake-up times and energy-saving modes. These characteristics support designs that spend substantial time sleeping and must resume quickly for sensor acquisition, control updates, or communications. The EFM32G222F32-QFP48 is available in a 7x7 mm 48-pin TQFP package, making it suitable for compact PCB layouts. Its 32-bit ARM Cortex-M3 core and peripheral mix can handle motor-control tasks, industrial monitoring, consumer accessories, and connected sensor nodes. Designers should select the appropriate operating voltage, pin multiplexing, clock configuration, and low-power strategy for the target system. Typical applications include low-power sensor nodes, industrial condition-monitoring equipment, small motor controllers, building-control endpoints, and portable measurement products. In each case, the MCU controls acquisition, timing, logic, and external interfaces while using its low-power modes between activity periods. The exact input voltage limits, current consumption, pin names, package dimensions, and electrical limits must be taken from the manufacturer datasheet rather than inferred from distributor summaries. A key design consideration is the relationship between sleep-mode selection and wake-up latency. For battery-powered systems, choose the lowest acceptable active and sleep currents while ensuring that the required peripherals respond within the control-loop timing budget. Also budget Flash, RAM, stack depth, and firmware overhead before adding protocol libraries or advanced control algorithms. This page combines manufacturer specifications, distributor product information, datasheet access, package details, and engineering guidance to support component selection and PCB planning. It is intended to make the EFM32G222F32-QFP48 searchable by MPN, ARM Cortex-M3, 32 MHz, 32 kB Flash, 8 kB RAM, and 48-pin TQFP-related design requirements.

詢價 聯絡我們
EFM32G222F64-QFP48 - 32MHz Cortex-M3 64KB MCU | Silicon Labs
EFM32G222F64-QFP48

EFM32G222F64-QFP48 - 32MHz Cortex-M3 64KB MCU | Silicon Labs

Silicon Labs EFM32G222F64-QFP48 is an ARM Cortex-M3 microcontroller (MCU) operating up to 32 MHz, with 64 kB of Flash memory, 16 kB of RAM, 37 digital I/O pins, three 16-bit timers, and a 48-pin TQFP package. Designed around the EFM32 Gecko low-power platform, it combines fast wake-up operation and energy-saving modes for compact, energy-sensitive embedded systems. A microcontroller is a programmable system-on-chip that integrates a processor core, memory, peripherals, and I/O into one component. The EFM32G222F64 belongs to the hierarchy of 32-bit MCU, embedded processor, semiconductor, and power-managed control platform. Its ARM Cortex-M3 core provides a 32-bit processing architecture for real-time control, while the Gecko platform focuses on reducing energy use between short processing bursts. Key features include a maximum clock frequency of 32 MHz, 64 kB of Flash for firmware, and 16 kB of RAM for working data. The device provides 37 digital I/O pins and three dedicated 16-bit timers, making it suitable for products requiring multiple control outputs, periodic sensing, motor or actuator timing, and low-power autonomous behavior. The 48-TQFP package is 7 mm by 7 mm and supports surface-mount PCB assembly. The Cortex-M3 architecture and low-power Gecko design make this MCU appropriate for always-on embedded subsystems that must react quickly without continuously consuming maximum power. The verified manufacturer and distributor descriptions specifically identify fast wake-up times and energy-saving modes as platform capabilities. Detailed peripheral lists, memory organization, voltage limits, temperature limits, and package dimensions beyond the supplied data should be confirmed in the manufacturer documentation before a final design is released. Typical uses include industrial sensor nodes, compact building-control modules, low-power monitoring equipment, connected accessories, and embedded control subsystems. Designers can allocate the 64 kB Flash region to application firmware and configuration data while using the 16 kB RAM for working buffers. The three 16-bit timers support periodic counting, input capture, output compare, or other timing functions depending on the device configuration. The primary design consideration is low-power system architecture. Sensors, communications, and actuator drivers should be enabled only when required, and firmware should use the MCU's sleep and wake behavior to reduce average consumption. PCB layout should preserve clean grounding and short signal paths, while production firmware should be validated across voltage, temperature, and wake-up conditions intended for the end product. This page combines the verified manufacturer specifications, distributor availability references, package details, and practical engineering guidance. It also distinguishes exact same-package family options from devices that differ materially in memory or generation, preventing those parts from being presented as unqualified drop-in replacements.

詢價 聯絡我們
EFM32G222F64G-E-QFP48 - 32MHz Cortex-M3 | Silicon Labs
EFM32G222F64G-E-QFP48

EFM32G222F64G-E-QFP48 - 32MHz Cortex-M3 | Silicon Labs

The Silicon Labs EFM32G222F64G-E-QFP48 is an ARM Cortex-M3 microcontroller operating up to 32 MHz, with 64 kB of Flash memory, 16 kB of RAM, and 37 digital I/O pins in a 48-pin TQFP package measuring 7 x 7 mm. The EFM32G222F64G-E-QFP48 also includes AES hardware, three 16-bit timers, and a 1.98 V to 3.8 V supply range. An ARM Cortex-M3 microcontroller is a 32-bit embedded processor built around the ARM Cortex-M3 instruction set. Within the semiconductor hierarchy, it belongs to the microcontroller and embedded-processing category, combining a processor core, nonvolatile program memory, volatile data memory, peripherals, and communication interfaces in one package. The EFM32 Gecko platform targets compact, energy-sensitive embedded systems where processing capability must coexist with efficient power management. The principal benefits of this device include its 32 MHz Cortex-M3 core, 64 kB Flash configuration storage, and 16 kB working RAM. Three 16-bit timers support periodic timing, input capture, output compare, and basic motor-control tasks. The 37 digital I/O pins provide flexible connections for sensors, displays, communication interfaces, and control signals, while the TQFP-48 footprint remains straightforward to inspect and solder using conventional surface-mount assembly methods. The EFM32G222F64G-E-QFP48 is based on Silicon Labs' EFM32 Gecko low-power platform, which includes fast wake-up behavior and energy-saving operating modes. Its AES hardware adds a dedicated cryptographic capability for systems that need hardware-assisted data protection. These characteristics make it useful in connected sensors, industrial monitoring equipment, compact control systems, and battery-operated products where the combination of processing throughput, memory, and low-power operation is important. Typical applications include environmental monitoring, smart metering, portable instrumentation, building controls, connected industrial nodes, and embedded sensor hubs. Designers can use the 37 digital I/O pins for discrete sensors and actuators, the 16 kB RAM for working buffers, and the three 16-bit timers for periodic measurement or timing functions. The AES capability is particularly relevant when local data must be protected without offloading every encryption operation to software. PCB design should preserve the EFM32G222F64G-E-QFP48 power requirements, decoupling, clock stability, and exposed programming or debug access. Place the required bypass capacitors close to their associated supply pins, maintain short return paths for power and ground, and follow Silicon Labs' recommended reference layout. Confirm the exact pin assignments, programming interface, and peripheral multiplexing in the manufacturer datasheet before finalizing a board. This product page combines the exact target ordering code with verified family-level electrical details, practical application guidance, package considerations, and a strict pin-compatible replacement assessment. It also distinguishes genuine drop-in options from nearby devices that differ in core architecture, memory capacity, or peripheral configuration, helping engineers evaluate replacement risk before committing a new PCB revision.

詢價 聯絡我們
EFM32G230F128-QFN64 - 32MHz ARM Cortex-M3 MCU | Silicon Labs
EFM32G230F128-QFN64

EFM32G230F128-QFN64 - 32MHz ARM Cortex-M3 MCU | Silicon Labs

Silicon Labs EFM32G230F128-QFN64 is an ARM Cortex-M3 microcontroller operating up to 32 MHz, with 128 kB of Flash memory, 16 kB of RAM, and 56 digital I/O pins in a 64-QFN package. The device combines a low-power Gecko platform with fast wake-up capability, energy-saving operating modes, and autonomous peripherals for energy-sensitive embedded systems. A microcontroller is a programmable semiconductor that integrates a processor core, memory, digital interfaces, timers, and analog peripherals onto one device. The EFM32G230 belongs to the 32-bit microcontroller hierarchy and combines ARM Cortex-M3 processing with Silicon Labs’ EFM32 energy-management architecture. This combination makes it suitable for portable instruments, industrial sensors, connected equipment, and other embedded-control systems that require compact software support and low standby consumption. Three principal specifications define this part: a maximum CPU frequency of 32 MHz, 128 kB of embedded Flash, and 16 kB of SRAM. It also provides 56 digital I/O pins and three 16-bit timers. The EFM32G family can consume as little as 0.6 µA in Stop mode and 180 µA/MHz in Run mode, helping designers reduce average system power when the application spends substantial time asleep. The EFM32 architecture is intended to keep the processor inactive while peripheral functions continue to operate. Its low-energy techniques, fast wake-up behavior, and autonomous peripherals reduce the time and energy required to service common events such as timers, serial communication, and sensor interrupts. The three 16-bit timers support periodic and timing-intensive embedded tasks, while the 56 GPIO pins provide flexibility for switches, indicators, communications, and control signals. Typical uses include low-power sensor nodes, industrial monitoring modules, compact energy-harvesting equipment, building-control endpoints, portable measurement devices, and connected battery-powered products. The 32 MHz Cortex-M3 core provides sufficient performance for protocol handling, control loops, and moderate real-time processing, while the 128 kB Flash and 16 kB RAM suit firmware with moderate code and working-memory requirements. PCB planning should account for the 64-QFN footprint, its exposed thermal pad, and the manufacturer’s pin and land-pattern requirements. Decoupling, a stable supply source, exposed-pad thermal coupling, and correct boot configuration are essential for reliable operation. This page combines manufacturer specifications, drop-in options, application guidance, and design-focused comparisons for engineers evaluating the EFM32G230F128-QFN64.

詢價 聯絡我們
EFM32G230F32-QFN64 - 32MHz Cortex-M3 MCU | Silicon Labs
EFM32G230F32-QFN64

EFM32G230F32-QFN64 - 32MHz Cortex-M3 MCU | Silicon Labs

The Silicon Labs EFM32G230F32-QFN64 is a 32-bit ARM Cortex-M3 Gecko microcontroller operating up to 32 MHz, with 32 kB of Flash memory, 8 kB of RAM, and 56 digital I/O pins in a 64-QFN 9 x 9 mm package. It combines a low-power platform with autonomous peripherals and energy-saving modes for embedded control applications. A microcontroller is a semiconductor device that integrates a processor core, memory, peripherals, and interfaces into one compact component. Within the hierarchy of embedded semiconductors, an MCU is a programmable controller used to acquire inputs, execute firmware, and control outputs. The EFM32G230F32-QFN64 belongs to the Gecko family of ARM Cortex-M3 devices suited to low-power, energy-sensitive systems. Verified product information identifies a 32-bit CPU, a 32 MHz maximum speed, 32 kB Flash, 8 kB RAM, 56 digital I/O pins, and three 16-bit timers. The family-level datasheet also reports low-power operation with consumption as low as 0.6 uA in Stop mode and 180 uA/MHz in Run mode. These figures support battery-powered sensing, portable monitoring, and industrial control designs where efficiency matters. The Gecko architecture adds fast wake-up behavior and autonomous peripherals, allowing selected functions to operate with less CPU intervention. This can reduce active processing time in systems that periodically acquire data or respond to external events. The MCU also integrates digital and analog functions in one device, helping reduce board area compared with separate processor and discrete interface components. Typical uses include sensor nodes, building automation endpoints, portable instruments, connected equipment, and low-power embedded control. The 56 digital I/O pins provide substantial external connectivity, while the three 16-bit timers support periodic timing, pulse measurement, motor-control timing, or basic event generation. The 9 x 9 mm QFN package is suitable for compact boards but requires careful thermal and layout planning. Designers should confirm the exact pin functions, exposed-pad connection, operating voltage, clock configuration, and required decoupling directly from the manufacturer datasheet and reference manual. Because the available verified data does not provide a complete package pin map or several operating-limit values, those details must not be inferred. This product synthesis combines verified distributor identity, family-level performance data, package information, and practical selection guidance. It separates documented facts from unavailable parameters so procurement and engineering decisions remain traceable.

詢價 聯絡我們
EFM32G230F64-QFN64 - 32MHz Cortex-M3 64KB MCU | Silicon Labs
EFM32G230F64-QFN64

EFM32G230F64-QFN64 - 32MHz Cortex-M3 64KB MCU | Silicon Labs

The Silicon Labs EFM32G230F64-QFN64 is an ARM Cortex-M3 Gecko microcontroller IC operating up to 32 MHz, with 64 kB of Flash memory, 16 kB of RAM, 56 digital I/O pins, and a 64-QFN 9 x 9 mm package. It is designed for energy-sensitive embedded systems that require a 32-bit microcontroller, low-power operation, and integrated mixed-signal and connectivity features. A microcontroller is a programmable integrated circuit containing a processor core, memory, peripherals, and I/O interfaces. In the product hierarchy, the EFM32G230F64-QFN64 belongs to the EFM32 Gecko family of 32-bit embedded processors, based on the ARM Cortex-M3 architecture. It is intended for use in industrial, consumer, medical, and other battery-powered or energy-constrained electronic products. Key features include a 32 MHz ARM Cortex-M3 processor, 64 kB Flash, 16 kB RAM, 56 digital I/O pins, and three 16-bit timers. The EFM32G platform also provides low-power operating techniques, fast wake-up behavior, energy-saving modes, and autonomous peripherals. According to the Silicon Labs EFM32G datasheet, devices in the family can consume as little as 0.6 microamps in Stop mode and 180 microamps per megahertz in Run mode. The EFM32G230F64-QFN64 integrates substantial peripheral functionality into a compact package, reducing the need for external components in connected embedded designs. Its 56 digital I/O pins provide interface capacity for sensors, actuators, communications, human-interface elements, and control signals. The three 16-bit timers support timing, counting, pulse-width modulation, and periodic event generation, while the integrated analog and communication resources are useful for monitoring, control, and energy-sensitive connected products. Typical applications include low-power sensor nodes, industrial monitoring equipment, medical instrumentation, consumer accessories, battery-powered controls, and connected embedded systems. The device is particularly suitable when a compact 32-bit control platform is needed without the memory footprint of a larger microcontroller. PCB design should follow Silicon Labs hardware-design guidance, including careful exposed-pad thermal management, supply decoupling, and validation of the final power and ground layout. Because the supplied product information does not include a complete manufacturer pinout table, the complete 64-pin mapping cannot be reproduced safely without verification against the official datasheet. This page consolidates verified manufacturer and distributor information, distinguishes the core EFM32G230F64-QFN64 from its tape-and-reel ordering suffix, and provides engineering-oriented application and comparison guidance rather than repeating only catalog metadata.

詢價 聯絡我們
EFM32G232F128-QFP64 - 32MHz ARM Cortex-M3 MCU, 128KB Flash, 64-TQFP | Silicon Labs
EFM32G232F128-QFP64

EFM32G232F128-QFP64 - 32MHz ARM Cortex-M3 MCU, 128KB Flash, 64-TQFP | Silicon Labs

The Silicon Labs EFM32G232F128-QFP64 is an ARM Cortex-M3 based 32-bit microcontroller (MCU) operating up to 32 MHz, with 128 kB of Flash and 16 kB of RAM, housed in a 64-pin TQFP (10x10 mm) package. It is part of the energy-friendly EFM32 Gecko family and supplies 53 digital I/O pins, 3 x 16-bit timers/counters, and a peripheral set optimised for low-energy applications. Supply voltage is 1.98 V to 3.8 V, allowing direct connection to coin cells, 2x AA, or regulated 3.3 V rails. An MCU (microcontroller) is a single-chip computer that integrates a CPU core, non-volatile program memory (Flash), volatile working memory (RAM), and a configurable set of analog and digital peripherals. The Cortex-M3 core sits in the broader ARM Cortex-M hierarchy (Cortex-M0/M0+/M3/M4/M7) and is widely used where deterministic real-time response, low power, and a rich instruction set (Thumb-2) are required. Within Silicon Labs' portfolio, the EFM32 Gecko series sits between the entry-level EFM32 Zero Gecko and the higher-end EFM32 Wonder Gecko / Pearl Gecko families, distinguished by its peripheral reflex system and ultra-low standby currents below 1 microamp in EM4 deep sleep. Key features of the EFM32G232F128-QFP64 include hardware AES encryption, a 12-bit ADC, brown-out reset, DMA, and energy-aware peripherals such as the LESENSE and LETIMER blocks. Communication interfaces span I2C, SPI, UART/USART, IrDA, and SmartCard, while timers include PWM output and a watchdog. The peripheral reflex system allows peripherals to interact without CPU wake-up, reducing active time and average current. Typical applications include battery-powered wireless sensor nodes, energy-harvesting devices, smart metering, home and building automation, wearable health monitors, and industrial IoT edge nodes. In each case, the Gecko's fast wake-up (a few microseconds from EM2), low active current (about 7 mA at 32 MHz), and 53 GPIO enable rich connectivity with multi-year battery life. When designing with this device, carefully budget active-mode current versus sleep-mode duty cycle to maximise battery life, and follow Silicon Labs' reference layouts to maintain ADC accuracy near RF sections. Stack the firmware on top of the Gecko SDK or emlib to access the energy-management unit and the peripheral reflex system that differentiate this MCU from generic Cortex-M3 parts. This page synthesises distributor pricing, same-package drop-in alternatives, and design notes beyond what the manufacturer datasheet alone provides, making it easier to evaluate the EFM32G232F128-QFP64 for low-energy embedded designs.

詢價 聯絡我們
EFM32G232F128G-E-QFP64 - 32MHz ARM Cortex-M3 MCU, 128KB Flash | Silicon Labs
EFM32G232F128G-E-QFP64

EFM32G232F128G-E-QFP64 - 32MHz ARM Cortex-M3 MCU, 128KB Flash | Silicon Labs

The Silicon Labs EFM32G232F128G-E-QFP64 is an ARM Cortex-M3 Gecko microcontroller IC running at 32 MHz with 128 kB (128K x 8) of flash program memory and 16 kB of RAM, housed in a 64-pin TQFP (10 mm x 10 mm) surface-mount package. It is a member of the energy-friendly EFM32 Gecko family designed for ultra-low-power embedded designs. An ARM Cortex-M3 microcontroller (MCU) is a 32-bit processor core from Arm Holdings featuring the Thumb-2 instruction set, hardware divide, atomic bit-banding, and a deterministic nested vector interrupt controller (NVIC). Cortex-M3 sits in the Cortex-M family hierarchy (Cortex-M0/M0+ -> Cortex-M3 -> Cortex-M4/M7) and is widely used for cost-sensitive embedded applications requiring more performance than M0/M0+ can deliver. The EFM32G family is positioned by Silicon Labs as one of the lowest-energy Cortex-M3 product lines on the market. Key features include 53 digital I/O pins, 3 x 16-bit timers, AES hardware encryption, autonomous peripherals that operate in sleep modes, ultra-fast wake-up from sleep, an integrated LESENSE / low-energy sensor interface block, and on-chip analog such as ADC and comparator blocks. The Gecko series targets battery-powered systems with typical Stop current of 0.6 uA and Run current of 180 uA/MHz per the EFM32G datasheet. The device operates across the industrial -40C to +85C range. Architecturally, the part uses a Cortex-M3 core with a peripheral reflex system (PRS) that lets peripherals signal each other without CPU intervention - a key energy saver. Flash and RAM are accessed through the AHB-Lite bus, and low-energy peripherals are placed on a separate APB bus so they can run while the CPU sleeps. Typical applications include battery-powered IoT sensors, wearable health monitors, smart metering, wireless sensor nodes paired with sub-GHz or BLE companions, and industrial HMI / alarm panels. The integrated AES block is suitable for encrypted firmware update and secure authentication. When designing with this device, plan the decoupling network carefully: place 100 nF and 1 uF capacitors as close as possible to each VDD pin pair, and follow the EFM32G hardware design guide for the 32 kHz crystal layout to avoid extra current draw from a high-ESR load. A JTAG or SWD header is required for programming - the on-chip debug interface is supported by Simplicity Studio and the J-Link toolchain.

詢價 聯絡我們
EFM32G232F128G-E-QFP64R - 32MHz Cortex-M3 MCU 128KB Flash | Silicon Labs
EFM32G232F128G-E-QFP64R

EFM32G232F128G-E-QFP64R - 32MHz Cortex-M3 MCU 128KB Flash | Silicon Labs

The Silicon Labs EFM32G232F128G-E-QFP64R is a 32-bit ARM Cortex-M3 based Gecko microcontroller IC integrating 128KB Flash, 16KB RAM, AES encryption hardware, and an autonomous peripheral set, housed in a 64-pin TQFP (10x10 mm) package. It operates from a 1.98V to 3.8V supply at up to 32MHz core clock and offers 53 general-purpose I/O pins, the Low Energy Sensor Interface (LESENSE), and the peripheral reflex system that lets timers, ADCs, and GPIOs react without CPU wakeup. A microcontroller (MCU) is an integrated circuit that combines a processor core, program and data memory, peripherals, and interrupt logic on a single chip. The Cortex-M3 family is a 32-bit RISC core designed for embedded applications, balancing deterministic interrupt latency, Thumb-2 instruction efficiency, and a tightly integrated NVIC. The EFM32G "Gecko" family belongs to the broader ARM Cortex-M MCU ecosystem within Silicon Labs' energy-friendly portfolio, positioning it between 8-bit MCUs and higher-end Cortex-M4 application processors. Key features of the EFM32G232F128G-E-QFP64R include 0.6 uA Stop mode current (RTC running), 180 uA/MHz Run mode current, hardware AES-128 encryption accelerator, 12-bit ADC, 8-channel DMA, integrated LCD controller, and 2x analog comparator plus 3x operational amplifier (op-amp) blocks. This peripheral integration reduces external bill-of-materials for sensor and metering designs, while the autonomous LESENSE block can scan capacitive or inductive sensors in deep sleep. The architecture centers on a low-leakage CMOS process and energy-modes-aware clock gating, allowing the device to enter EM2/EM3 deep-sleep states while still triggering wakeup from GPIO, RTC, or LESENSE events. The peripheral reflex system (PRS) routes peripheral events over dedicated fabric channels, offloading routine signal routing from the CPU and enabling sub-microsecond response without leaving sleep. Typical applications include battery-powered IoT sensor nodes, smart HVAC thermostats, water/gas utility metering, wireless sensor hubs front-ending sub-GHz radios, wearable health patches, and industrial asset tracking tags. The on-chip AES-128 block and 128KB Flash also suit retrofit devices that need authenticated firmware updates over BLE/Zigbee companion ICs. When designing with the EFM32G232F128G-E-QFP64R, budget decoupling capacitors close to every VDD/VDD_x pair, route the 32kHz crystal traces symmetrically, and leverage the EFM32 CMSIS-Pack and Simplicity Studio for peripheral configuration to avoid hidden power draw from misconfigured GPIO retention modes. This page synthesizes distributor stock, parametric cross-references, and design guidance beyond the manufacturer datasheet, helping engineers select drop-in same-package variants and understand where this Gecko MCU fits within the wider ARM Cortex-M3 landscape.

詢價 聯絡我們
EFM32G232F32-QFP64 - 32MHz Cortex-M3 MCU | Silicon Labs
EFM32G232F32-QFP64

EFM32G232F32-QFP64 - 32MHz Cortex-M3 MCU | Silicon Labs

The Silicon Labs EFM32G232F32-QFP64 is an ARM Cortex-M3 32-bit microcontroller operating up to 32 MHz, with 32 kB of Flash memory, 8 kB of RAM, and 53 digital I/O pins in a 64-TQFP package. It combines conventional embedded processing with a low-power Gecko platform designed for energy-sensitive systems. A microcontroller is a programmable system-on-chip that integrates a processor core, memory, peripherals, and I/O into one device. The ARM Cortex-M3 belongs to the embedded microcontroller hierarchy, while the EFM32G family adds low-power design techniques, fast wake-up behavior, and energy-saving modes. This makes the device suitable when a design needs more control capability than a simple fixed-function controller without adopting a more complex high-performance processor. The EFM32G232F32-QFP64 provides 32 kB Flash for firmware and 8 kB RAM for working data. Its 53 digital I/O pins support external sensors, indicators, switches, communications interfaces, and control signals. Three 16-bit timers are included for periodic events, timing, input capture, output compare, or other timer-based functions. The 32 MHz Cortex-M3 core provides a balance of processing speed and low-power operation for embedded control. The verified manufacturer result specifically identifies the device as an ARM Cortex-M3 based MCU with speeds up to 32 MHz and highlights its low-power platform, fast wake-up times, energy-saving modes, 32 kB Flash, 8 kB RAM, 53 digital I/O pins, and three 16-bit timers. Exact supply voltage, peripheral details, package dimensions, temperature limits, memory organization, and electrical characteristics were not included in the supplied source snippets and therefore remain marked where data is needed. Typical uses include low-power sensor nodes, industrial control products, building automation modules, connected measurement equipment, small motor-control systems, and portable embedded instruments. The 64-TQFP package exposes more I/O than smaller packages and can simplify board-level routing when a design requires several external connections. Compared with a low-pin-count MCU, the EFM32G232F32-QFP64 offers additional I/O flexibility while retaining a compact surface-mount form factor. Designers should verify the complete manufacturer datasheet before layout, firmware development, or production release. Pay particular attention to power sequencing, decoupling, exposed-pin requirements, clock configuration, programming method, peripheral multiplexing, and the exact meanings of all 64 package pins. The supplied data supports the core, memory, speed, I/O, timer, package, and low-power claims above but does not provide a complete electrical table. This page consolidates the verified manufacturer and distributor search results, records unavailable technical fields transparently, and distinguishes the target MCU from package-only or functionally similar alternatives. The primary sourcing path is the Silicon Labs product page, supplemented by distributor records for procurement and additional datasheet discovery.

詢價 聯絡我們
EFM32G232F64-QFP64 - 32MHz Cortex-M3 64KB Flash MCU | Silicon Labs
EFM32G232F64-QFP64

EFM32G232F64-QFP64 - 32MHz Cortex-M3 64KB Flash MCU | Silicon Labs

The Silicon Labs EFM32G232F64-QFP64 is an ARM Cortex-M3 based 32-bit microcontroller (MCU) running up to 32 MHz, with 64 kB Flash (64K x 8), 16 kB RAM and 53 digital I/O pins, supplied in a 64-TQFP (10x10 mm) package operating from 1.98 V to 3.8 V. It belongs to the EFM32 Gecko family, a low-power 32-bit MCU platform built around energy-conscious techniques, fast wake-up times and multiple energy-saving modes. An MCU (microcontroller) is a single integrated circuit containing a CPU core, program memory, data memory and peripherals. In the taxonomy a microcontroller is a type of integrated circuit and semiconductor, and within that group it sits beside memory ICs, interface ICs, ADC/DAC and clock & timing devices. The Gecko family specifically targets energy-sensitive embedded systems where average current draw, not just peak performance, determines battery life. Key features of this device include a 32 MHz ARM Cortex-M3 core with integrated sleep and stop modes, 64 kB of flash for firmware and 16 kB of SRAM for working memory, three 16-bit timers, and hardware AES support as noted in the Mouser listing for this part number. A wide 1.98 V to 3.8 V supply range makes the part usable across 2.5 V and 3.3 V system rails, and the 64-TQFP 10x10 mm footprint keeps the board area small while exposing 53 GPIO for sensors, actuators and communications. Technically the part belongs to the Gecko series, whose energy-saving modes and fast wake-up behaviour are the differentiating architectural features versus generic Cortex-M3 devices. Because the device is available in a 64-pin TQFP, designers get both fine-grained pin multiplexing and a package that is straightforward for automated assembly, pick-and-place and visual inspection, unlike fine-pitch QFN or BGA options. Typical applications include low-power sensor nodes and IoT end devices, industrial monitoring and control modules, building and energy metering equipment, portable and wearable accessories, and USB-connected peripheral controllers where the 53 available I/O pins allow several peripherals to share one package. A key design consideration is that the flash capacity and RAM size define how much application code and data buffering fit on the die; designs that need large buffers should consider the 128 kB and 256 kB members of the Gecko family instead of this 64 kB variant. This page synthesizes distributor pricing, verified drop-in alternatives, pin-level guidance and practical design notes that are not found together in the manufacturer datasheet, helping engineers shorten BOM and layout decisions for EFM32G232F64-QFP64.

詢價 聯絡我們
EFM32G280F32-QFP100 - 32MHz Cortex-M3 MCU | Silicon Labs
EFM32G280F32-QFP100

EFM32G280F32-QFP100 - 32MHz Cortex-M3 MCU | Silicon Labs

Silicon Labs EFM32G280F32-QFP100 is a 32-bit ARM Cortex-M3 Gecko microcontroller rated up to 32 MHz, with 32 kB of flash memory, 8 kB of RAM, and 86 digital I/O pins in a 100-pin LQFP package measuring 14 x 14 mm. The device combines conventional embedded-control processing with energy-saving modes and fast wake-up behavior for energy-conscious systems. A microcontroller is a semiconductor device that integrates a processor core, program memory, data memory, peripherals, and I/O into one compact component. The EFM32G280 belongs to the EFM32 Gecko family, a hierarchy of ARM Cortex-M3 microcontrollers designed for embedded control, low-power sensing, communications, and industrial applications. Its architecture provides general-purpose computation alongside dedicated timers and energy-management functions. The EFM32G280F32-QFP100 includes 3 x 16-bit timers, 86 digital I/O pins, and operation up to 32 MHz. Its 32 kB flash stores firmware, while 8 kB RAM supports working data, stack space, and peripheral buffers. The 100-pin LQFP provides enough connections for external sensing interfaces, communications, control outputs, and debug or programming access without relying on a very small package. The Cortex-M3 processor supports a 32-bit instruction set and an efficient embedded-control architecture. Silicon Labs positions the Gecko platform around low-energy operation, rapid transitions from energy-saving states, and multiple sleep-related operating modes. These characteristics help reduce the average energy consumed by systems that spend much of their time monitoring inputs rather than executing continuous computation. Typical applications include low-power sensor nodes, connected industrial equipment, environmental monitoring, compact control systems, and energy-harvesting products. The combination of 86 digital I/O pins and three 16-bit timers is particularly useful when a design needs multiple discrete inputs, timing channels, motor or actuator control, and communication peripherals on a single controller. PCB implementation should preserve the 100-pin LQFP footprint, provide clean grounding, and route sensitive signal paths away from switching nodes. Designers should also budget flash and RAM for the complete firmware, interrupt handlers, and application state rather than relying only on nominal application-code size. Confirm the complete pin assignments and peripheral multiplexing in the manufacturer pinout table before final routing. This page consolidates the manufacturer specifications, package information, sourcing guidance, and design considerations needed to evaluate the EFM32G280F32-QFP100. It also identifies the constraints involved in finding a genuine same-footprint replacement, rather than presenting devices with incompatible memory sizes or peripheral configurations as drop-in choices.

詢價 聯絡我們
EFM32G280F64-QFP100 - 32MHz Cortex-M3 MCU | Silicon Labs
EFM32G280F64-QFP100

EFM32G280F64-QFP100 - 32MHz Cortex-M3 MCU | Silicon Labs

The Silicon Labs EFM32G280F64-QFP100 is an ARM Cortex-M3 microcontroller operating up to 32 MHz, with 64 kB of flash memory, 16 kB of RAM, and 86 digital I/O pins in a 100-LQFP package. It also provides three 16-bit timers and operates from a 3 V supply, making it suitable for compact embedded systems requiring substantial I/O and low-power operation. A microcontroller is a programmable semiconductor that integrates a processor core, memory, peripheral interfaces, and I/O into one device. The EFM32G280F64-QFP100 belongs to the 32-bit embedded MCU hierarchy and uses the ARM Cortex-M3 architecture. It is designed for applications where local control, communication, sensing, and actuator control must be handled by a compact embedded platform. The device combines a 32 MHz ARM Cortex-M3 processor with 64 kB of flash and 16 kB of RAM. Its 86 digital I/O pins provide broad connectivity for sensors, displays, communications, and control signals. Three 16-bit timers support periodic timing, pulse measurement, and timing-intensive control functions. The listed AES capability adds hardware support for applications requiring encrypted data handling. Silicon Labs describes the Gecko platform around low-energy techniques, fast wake-up behavior, and energy-saving operating modes. These characteristics are particularly useful in battery-powered or intermittently powered equipment. The external oscillator configuration listed for this family supports designs where precise timing derives from an external clock source rather than an internal oscillator alone. Typical uses include industrial monitoring, energy-sensitive sensor nodes, building automation, connected equipment, and compact embedded controllers. The high pin count can reduce the need for I/O expanders in designs that connect multiple discrete sensors, status indicators, communications lines, and actuator outputs to one controller. PCB implementation requires attention to the 100-LQFP footprint, power routing, decoupling, clock stability, programming access, and exposed peripheral limits. Place the required decoupling capacitors close to the supply pins, route high-current returns through a stable ground plane, and follow the manufacturer's pin-description table when assigning tracks. Confirm boot, programming, and reset behavior in hardware before releasing the layout. This product page consolidates the core specifications, practical use cases, package information, and sourcing options for the EFM32G280F64-QFP100. It also provides a structured comparison with closely related Silicon Labs EFM32 devices to help engineers distinguish ordering codes, memory capacity, and peripheral differences without overlooking PCB compatibility.

詢價 聯絡我們
EFM32G290F128-BGA112 - 32MHz Cortex-M3 MCU | Silicon Labs
EFM32G290F128-BGA112

EFM32G290F128-BGA112 - 32MHz Cortex-M3 MCU | Silicon Labs

Silicon Labs EFM32G290F128-BGA112 is a 32-bit ARM Cortex-M3 microcontroller operating up to 32 MHz, with 128 kB flash memory, 16 kB RAM, and 90 digital I/O pins, housed in a 112-BGA package measuring 10 x 10 mm. The device also integrates eight 12-bit ADC channels, two 12-bit DAC channels, and AES hardware security for connected and energy-conscious embedded systems. A microcontroller is a programmable semiconductor that integrates a processor core, memory, peripherals, and I/O into one device. The EFM32G290 belongs to the EFM32 Gecko family and the broader embedded-controller hierarchy: Cortex-M3 processor core, 32-bit microcontroller, embedded processor, and semiconductor. Its combination of 128 kB flash, 16 kB RAM, and extensive mixed-signal peripherals makes it suitable for compact control systems that require local processing without a separate external processor. The EFM32G290F128-BGA112 runs at up to 32 MHz and provides 90 digital I/O pins, giving a high pin count for a 10 x 10 mm BGA device. Three 16-bit timers support precise timing, motor control, and periodic sensing tasks. Eight 12-bit ADC channels and two 12-bit DAC channels provide integrated analog measurement and signal generation, reducing the need for external converters in many designs. Integrated AES hardware accelerates cryptographic operations for data protection and authenticated communication. Its low-power architecture is central to the Gecko design. Energy-saving modes, fast wake-up behavior, and low-energy techniques allow the processor to remain responsive while reducing consumption during idle periods. This is particularly useful in battery-operated equipment where the duty cycle alternates between brief processing intervals and long standby periods. The combination of a 32 MHz Cortex-M3 core and dedicated sleep behavior supports responsive control without requiring continuous high-frequency operation. Typical applications include connected sensor nodes, industrial condition-monitoring equipment, compact energy meters, building-automation endpoints, wearable accessories, and embedded gateways. The 90 available digital I/O pins can support displays, buttons, communication interfaces, status indicators, and external sensors, while the ADC and DAC channels support analog front ends. The integrated AES hardware can protect firmware-related secrets, configuration data, or communication payloads when an application requires encryption. For PCB design, use the manufacturer datasheet and application note AN0002, EFM32 Hardware Design Considerations, to assign BGA pads, route power and ground, manage decoupling, and verify exposed-pad and thermal-via requirements. Because this package has 112 fine-pitch BGA lands, inspection and assembly depend on suitable PCB density, pad geometry, solder-paste control, and reflow profiling. This product page combines device specifications, package guidance, application fit, and same-package replacement context to help engineers evaluate the EFM32G290F128-BGA112 before committing a new design. The comparison focuses on documented memory, speed, analog resources, security features, and package compatibility rather than treating devices with different memory configurations as interchangeable without review.

詢價 聯絡我們
EFM32G290F32-BGA112 - 32MHz ARM Cortex-M3 MCU | Silicon Labs
EFM32G290F32-BGA112

EFM32G290F32-BGA112 - 32MHz ARM Cortex-M3 MCU | Silicon Labs

Silicon Labs EFM32G290F32-BGA112 is a 32-bit ARM Cortex-M3 microcontroller operating up to 32 MHz, with 32 kB Flash, 8 kB RAM, 90 digital I/O pins, and three 16-bit timers in a 112-pin BGA package. The device combines conventional microcontroller processing with energy-saving modes and fast wake-up behavior for power-conscious embedded systems. A microcontroller is a semiconductor that integrates a processor core, programmable memory, peripheral interfaces, and I/O into one compact device. The EFM32G290 belongs to the Gecko family of 32-bit microcontrollers, where the ARM Cortex-M3 core sits within a broader hierarchy of embedded processor, microcontroller, and semiconductor products. Its role is to execute firmware and manage sensors, communications, actuators, and user interfaces while controlling energy use in battery-powered or intermittently powered equipment. Key device characteristics include a maximum CPU frequency of 32 MHz, 32 kB of Flash memory, and 8 kB of RAM. The manufacturer identifies 90 digital I/O pins and three 16-bit timers, providing resources for parallel digital signals, timing, counters, and periodic control functions. The Cortex-M3 architecture also supports efficient interrupt-driven firmware, while the Gecko low-power platform is intended to extend operating time in energy-sensitive applications. The 112-pin BGA package exposes a comparatively large pin count for a compact embedded design, making it suitable for systems requiring extensive I/O connectivity. Its 32-bit architecture provides greater addressing and computation capability than an 8-bit controller while retaining the deterministic, event-driven operation expected from embedded processors. Exact peripheral, supply, timing, and environmental limits should be confirmed against the manufacturer documentation before schematic release. Typical uses include connected sensor nodes, industrial monitoring equipment, building-control endpoints, compact consumer devices, and low-power instrumentation. The combination of fast wake-up capability, energy-saving modes, and three timers supports designs that periodically sample data, update a display or network link, and return to a reduced-energy state between events. These characteristics also make the MCU suitable for battery-operated accessories where predictable standby behavior is important. Designers should treat the BGA layout as a manufacturing-sensitive assembly feature, use the manufacturer land pattern and pin-assignment tables, and confirm the exact package dimensions and ball map before PCB release. Firmware development should use the documented EFM32 peripheral libraries and startup support for the Cortex-M3 core, and production designs should include the required decoupling, programming access, clock configuration, and brownout behavior. This page combines the manufacturer specifications with practical replacement, package, application, and design guidance. It helps engineers compare the EFM32G290F32-BGA112 with related Gecko devices, plan low-power architectures, and identify the documentation needed for a reliable 112-ball PCB design and firmware bring-up.

詢價 聯絡我們
EFM32G290F64-BGA112 - 32MHz Cortex-M3 64KB MCU | Silicon Labs
EFM32G290F64-BGA112

EFM32G290F64-BGA112 - 32MHz Cortex-M3 64KB MCU | Silicon Labs

Silicon Labs EFM32G290F64-BGA112 is a 32-bit ARM Cortex-M3 Gecko microcontroller operating up to 32 MHz, with 64 KB of Flash memory, 16 KB of RAM, 90 digital I/O pins, and three 16-bit timers. The device is supplied in a 112-pin BGA package measuring 10 mm by 10 mm. Its low-power architecture, fast wake-up capability, and energy-saving modes target energy-conscious embedded systems. A microcontroller is a programmable embedded-control component that integrates a processor core, memory, peripherals, and I/O into one semiconductor device. The EFM32G290F64-BGA112 belongs to the EFM32 Gecko family, where the Gecko architecture combines an ARM Cortex-M3 processor with Silicon Labs low-power peripherals. This hierarchy places it within 32-bit microcontrollers, embedded processors, and energy-efficient semiconductor control systems. Core resources include 64 KB of Flash for firmware and 16 KB of RAM for working data. The device provides 90 digital I/O pins and three 16-bit timers, enabling simultaneous peripheral functions in space-constrained designs. Its operating supply range is 1.98 V to 3.8 V. Silicon Labs emphasizes low power consumption, with the EFM32G family consuming as little as 0.6 microampere in Stop mode and 180 microamperes per megahertz in Run mode. The ARM Cortex-M3 core provides a 32-bit processing architecture while retaining a compact embedded footprint. Silicon Labs EFM32 devices also feature autonomous peripherals, high analog integration, and energy-management modes that can reduce activity when the processor is not required to run continuously. These characteristics make the MCU suitable for designs in which response time and standby current both matter. Typical applications include low-power sensor nodes, connected industrial equipment, compact consumer devices, and embedded control modules. The 90-pin interface count supports board-level integration involving communications, timers, analog inputs, and digital control signals. The small 10 mm by 10 mm BGA also supports compact assemblies when careful PCB routing, thermal design, and assembly process control are applied. Designers should evaluate low-power mode behavior, wake-up requirements, pin multiplexing, and BGA assembly constraints before finalizing the PCB. The manufacturer datasheet should be used to assign every ball and peripheral function. Power routing and decoupling require a stable 1.98 V to 3.8 V supply environment, while firmware should use the documented sleep and Stop-mode entry procedures to achieve the intended energy savings. This product overview combines the device architecture, memory resources, package information, low-power characteristics, application guidance, and engineering considerations needed to plan an EFM32G290F64-BGA112-based design. It also provides same-package alternatives, specification comparisons, and practical implementation guidance to support component selection and board development.

詢價 聯絡我們
EFM32G30F128-QFN64 - 32MHz Cortex-M3 128KB MCU | Silicon Labs
EFM32G30F128-QFN64

EFM32G30F128-QFN64 - 32MHz Cortex-M3 128KB MCU | Silicon Labs

The Silicon Labs EFM32G30F128-QFN64 is a 32-bit ARM Cortex-M3 Gecko microcontroller with a 32 MHz operating frequency, 128 KB of embedded flash memory, and 16 KB of RAM, supplied in a compact 64-QFN 9 x 9 mm package. It operates from a 1.98 V to 3.8 V supply and is designed for low-power embedded systems requiring efficient processing, analog integration, and autonomous peripheral operation. A microcontroller is a programmable semiconductor that combines a processor core, memory, and peripherals on one integrated circuit. The EFM32G30F128-QFN64 belongs to the Gecko family of 32-bit ARM Cortex-M3 microcontrollers, which sit within the hierarchy of embedded processors, microcontrollers, and semiconductor control devices. Its ARM Cortex-M3 core provides a 32-bit instruction set while the EFM32 peripheral architecture allows many hardware functions to operate with limited CPU involvement. The verified device data identifies a maximum clock frequency of 32 MHz, 128 KB of flash organized as 128K x 8, and 16 KB of SRAM. Silicon Labs specifies a 1.98 V to 3.8 V operating supply range and a 64-QFN package measuring 9 x 9 mm. The family datasheet also reports low power consumption, including as little as 0.6 uA in Stop mode and 180 uA/MHz in Run mode, making the device suitable for battery-powered and energy-conscious products. The Gecko architecture integrates high-speed analog and digital peripherals with the Cortex-M3 core. Product Revision E documentation identifies pin-compatible replacements for earlier EFM32G revision devices. However, firmware, peripheral configuration, and electrical behavior must still be checked against the specific part-number suffix before treating a related revision as a production substitute. A complete exposed-pad thermal design is essential because heat removal depends on the PCB copper area and thermal via arrangement. Typical uses include industrial sensing and control nodes, compact environmental monitors, battery-powered IoT endpoints, wearable accessories, and connected measurement instruments. The small 9 x 9 mm QFN footprint supports space-constrained designs where a larger quad flat package would be undesirable. The 128 KB flash capacity provides room for application firmware, protocol stacks, and boot code, while the 16 KB RAM supports task working memory and moderate buffering. Designers should follow the manufacturer's recommended power, decoupling, and exposed-pad land-pattern requirements. A high-quality local ground plane and short return paths help analog and digital sections remain stable under switching loads. Confirm the exact operating temperature grade, peripheral mix, and pin multiplexing for the ordered MPN before layout release because the verified distributor data does not specify those complete values. This page consolidates verified manufacturer specifications, distributor availability information, pin-compatible same-family options, package constraints, and practical engineering guidance. The comparison material also distinguishes genuine drop-in choices from related devices that require firmware or board-level qualification.

詢價 聯絡我們
EFM32G800F128G-E-D1I - 32MHz Cortex-M3 MCU | Silicon Labs
EFM32G800F128G-E-D1I

EFM32G800F128G-E-D1I - 32MHz Cortex-M3 MCU | Silicon Labs

The Silicon Labs EFM32G800F128G-E-D1I is a 32-bit ARM Cortex-M3 Gecko microcontroller with a 32 MHz operating frequency, 128 KB of flash memory, and a 1.98 V to 3.8 V supply-voltage range. The device is supplied as an unpackaged die for module, wafer-level, and embedded manufacturing applications rather than as a conventional leaded or surface-mount component. A microcontroller is an integrated circuit that combines a processor core, program memory, data memory, and peripherals such as timers, serial interfaces, analog blocks, and interrupt controllers. The EFM32G family belongs to the broader embedded-control hierarchy of microcontroller ICs and uses the ARM Cortex-M3 processor architecture for compact, real-time control systems. Key characteristics include a 32-bit single-core Cortex-M3 processor, 128 KB of flash organized as 128K x 8, and operation from a 1.98 V to 3.8 V supply. According to the Silicon Labs EFM32G datasheet, the Gecko family consumes as little as 0.6 uA in Stop mode and 180 uA/MHz in Run mode, supporting applications where standby energy use is a primary design constraint. The EFM32G architecture combines autonomous peripherals with substantial analog and digital integration. Peripheral operation can continue with reduced processor intervention, helping deterministic control systems manage time-critical tasks. The Cortex-M3 core also supports efficient exception handling, while the integrated analog and communication resources reduce the component count required for sensor acquisition, industrial monitoring, and connected embedded products. Typical uses include low-power sensor nodes, battery-operated measurement instruments, industrial condition-monitoring equipment, compact control modules, and energy-harvesting products. The 128 KB flash capacity is suitable for moderate firmware images containing drivers, protocol stacks, application logic, and update services without requiring external program memory. The die package requires a package-specific assembly process, so the pin assignment, bonding plan, and exposed-pad requirements must be confirmed before layout. Use the EFM32G datasheet and EFM32G reference manual for die markings, pad locations, programming procedures, peripheral details, and production test requirements. This page consolidates the verified device identity, electrical envelope, power characteristics, die-package considerations, commercial ordering information, and design guidance into a single engineering reference for engineers evaluating the EFM32G800F128G-E-D1I for an embedded module or wafer-level design.

詢價 聯絡我們
EFM32G840F128-QFN64 - 32MHz Cortex-M3 128KB MCU | Silicon Labs
EFM32G840F128-QFN64

EFM32G840F128-QFN64 - 32MHz Cortex-M3 128KB MCU | Silicon Labs

Silicon Labs EFM32G840F128-QFN64 is a 32-bit ARM Cortex-M3 Gecko microcontroller rated up to 32 MHz, with 128 KB of Flash memory, 16 KB of RAM, and 56 digital I/O pins, packaged in a 64-QFN 9 x 9 mm package. The device operates from a 1.85 V to 3.8 V supply and supports an industrial temperature range of -40 °C to 85 °C. Three 16-bit timers and a low-energy platform make it suitable for embedded control, sensing, communications, and portable systems. A microcontroller is a programmable semiconductor that integrates a CPU core, nonvolatile program memory, volatile data memory, peripherals, and I/O into one device. The EFM32G840F128-QFN64 belongs to the EFM32 Gecko family, where the hierarchy is ARM Cortex-M3 processor, 32-bit MCU, embedded microcontroller, and semiconductor. It executes firmware from its 128 KB Flash memory while using 16 KB of RAM for working data and stack operations. Key features include operation up to 32 MHz, 56 digital I/O pins, and three 16-bit timer/counter peripherals. The 64-QFN package supports compact surface-mount layouts while its exposed pad provides a direct thermal path to the PCB. Low-energy operating techniques, fast wake-up behavior, and energy-saving modes are central to the Gecko architecture, making the MCU appropriate for systems that spend substantial time asleep. The ARM Cortex-M3 core provides a 32-bit RISC instruction set and an integrated interrupt architecture for responsive control applications. Flash memory stores the application firmware, while RAM supports the main loop, interrupt service routines, communication buffers, and sensor-processing state. The three 16-bit timers support periodic events, timing, input capture, or output compare functions, depending on the configured peripheral mode and the complete device documentation. Typical uses include industrial sensor nodes, low-energy wireless accessories, building-control endpoints, compact instrumentation, portable equipment, and embedded monitoring systems. Designers can select it where 128 KB of program storage, 16 KB of RAM, 56 GPIO, and a 32 MHz processing rate provide an appropriate balance between capability, board area, and energy-conscious operation. The principal design considerations are power-rail integrity, decoupling, exposed-pad thermal management, and correct firmware support for the QFN footprint. Place the required bypass capacitors close to their supply pins, provide a low-impedance ground plane, and follow the manufacturer's footprint and land-pattern guidance. Confirm peripheral availability, interrupt behavior, and low-power mode requirements against the manufacturer documentation before finalizing the design. This page combines the manufacturer's device specifications, package details, family alternatives, and practical implementation guidance to support component selection, PCB planning, firmware preparation, and sourcing decisions. The comparison tables and application sections emphasize where memory capacity, package compatibility, timer resources, and low-power operation matter in embedded product design.

詢價 聯絡我們
EFM32G840F32-QFN64 - 32MHz Cortex-M3 MCU | Silicon Labs
EFM32G840F32-QFN64

EFM32G840F32-QFN64 - 32MHz Cortex-M3 MCU | Silicon Labs

The Silicon Labs EFM32G840F32-QFN64 is an ARM Cortex-M3 32-bit microcontroller operating up to 32 MHz, with 32 kB of Flash memory, 8 kB of RAM, and 56 digital I/O pins in a 64-QFN package with an exposed pad. It is designed for energy-sensitive embedded systems. A microcontroller is a programmable system-on-chip that integrates a processor core, memory, digital interfaces, timers, analog peripherals, and power-management functions. The EFM32G840F32-QFN64 belongs to the EFM32 Gecko family and combines an ARM Cortex-M3 core with low-power operating techniques, short wake-up behavior, and energy-saving modes for battery-operated and portable equipment. Verified product information identifies 32 kB Flash, 8 kB RAM, 56 digital I/O pins, three 16-bit timers, and operation up to 32 MHz. The device is intended for applications that require compact embedded control, efficient peripheral integration, and low-energy operation. Its 64-QFN package provides a high pin count for digital connectivity in a relatively small surface-mount footprint. The EFM32G840F32-QFN64 is suitable for sensor nodes, industrial monitoring, building automation, portable measurement equipment, connected embedded products, and low-power control systems. The exposed pad supports thermal management when the device dissipates power during operation; PCB copper and thermal design should follow the manufacturer package guidance. When designing around this MCU, verify the exact pin multiplexing, supply requirements, peripheral availability, and package-specific exposed-pad requirements against the manufacturer datasheet. Do not substitute a different package or pin count without reviewing the complete pinout and board footprint. This page consolidates verified manufacturer and distributor information, datasheet access, application context, and replacement-screening guidance. It is intended to help engineers identify the correct EFM32G840F32-QFN64 for embedded designs rather than treating similar ARM MCUs as automatically interchangeable.

詢價 聯絡我們
EFM32G840F64-QFN64 - 32MHz Cortex-M3 MCU | Silicon Labs
EFM32G840F64-QFN64

EFM32G840F64-QFN64 - 32MHz Cortex-M3 MCU | Silicon Labs

The Silicon Labs EFM32G840F64-QFN64 is an ARM Cortex-M3 microcontroller operating up to 32 MHz, with 64 kB Flash, 16 kB RAM, and 56 digital I/O pins in a 64-QFN package. Designed for energy-sensitive embedded systems, it combines a low-power Gecko platform, fast wake-up capability, and energy-saving modes for responsive designs with constrained power budgets. A microcontroller is a programmable semiconductor that integrates a processor core, memory, I/O, timers, and communication peripherals on one integrated circuit. Within the product hierarchy, the EFM32G840F64-QFN64 is a 32-bit ARM Cortex-M3 MCU in the EFM32 Gecko family. It executes embedded control logic while providing local digital interfaces, analog functions, and low-power operating modes for connected products. The verified device features include a 32 MHz maximum CPU speed, 64 kB Flash, 16 kB RAM, 56 digital I/O pins, and three 16-bit timers. Distributor data also identifies a 64-QFN package with a 9 mm by 9 mm body and an exposed pad. The package supports surface-mount assembly, while the exposed pad provides the primary thermal connection on the PCB. The Cortex-M3 architecture gives the MCU a 32-bit processing interface suitable for control loops, human-interface logic, communications, and general embedded tasks. The Gecko low-power platform is particularly relevant in battery-operated equipment because the device combines conventional processing with energy-saving modes. Designers should use the Silicon Labs documentation to configure wake behavior, clocks, peripherals, and current-consumption targets for the exact product configuration. Typical uses include industrial sensor nodes, connected meters, portable medical accessories, smart-building controls, compact consumer devices, and low-energy IoT equipment. Its 56 digital I/O pins can support buttons, displays, indicators, and external interface signals, while the three 16-bit timers are useful for timing, pulse generation, and periodic control tasks. A critical design consideration is decoupling and exposed-pad layout. Place the required bypass capacitors close to the supply pins and connect the exposed thermal pad according to the manufacturer's package guidance. Validate the power rails, boot configuration, peripheral pin mapping, and low-power behavior on hardware before production. This page combines verified manufacturer and distributor facts with engineering-focused selection, comparison, sourcing, and design guidance. It is intended to help engineers identify the correct MCU, verify package assumptions, and assess migration options without relying on unverified electrical or lifecycle assumptions.

詢價 聯絡我們