產品(42,000+)

MSP430F5507IRGZR - 25MHz MCU, 32KB Flash, USB 2.0 | Texas Instruments
MSP430F5507IRGZR

MSP430F5507IRGZR - 25MHz MCU, 32KB Flash, USB 2.0 | Texas Instruments

The Texas Instruments MSP430F5507IRGZR is a 16-bit ultra-low-power mixed-signal microcontroller from the MSP430F5xx family, integrating a 25 MHz MSP430 CPUXV2 core with 32KB Flash, 6KB SRAM (one source quotes 4KB), a 10-bit ADC, DMA, UART/SPI/I2C serial interfaces, hardware multiplier, multiple timers, and a USB 2.0 full-speed peripheral. The device is housed in a 48-pin VQFN (RGZ) package measuring 7x7 mm with an exposed thermal pad. An MSP430 microcontroller is a 16-bit RISC mixed-signal MCU platform from Texas Instruments that occupies the low-power and battery-aware tier of the embedded MCU hierarchy. Within that platform hierarchy the device sits as: MSP430F5xx -> MSP430F55xx (USB sub-family) -> MSP430F550x -> MSP430F5507. The 'F' prefix indicates in-system programmable Flash, the '5' indicates the F5xx generation with the CPUXV2 core and 25 MHz operation, and the trailing digits indicate memory size and feature set. The platform is widely used where deterministic low power and integrated analog matter more than raw MHz. Key differentiating features include active-mode current of 180-195 uA/MHz at 3V, standby current of a few uA, a 1.4 V to 3.6 V wide core supply range (3.6 V absolute max), a true hardware USB 2.0 full-speed transceiver on-chip, a 10-bit successive-approximation ADC with up to 12 external input channels and sample-and-hold, a 32-bit hardware multiplier that accelerates DSP routines, and 31 general-purpose I/O pins. The internal oscillator removes an external crystal in many designs, and the DMA controller offloads data movement between peripherals and memory. At the architectural level, the device uses TI's von-Neumann unified memory map with a 16-bit CPUXV2 core, a 3-stage pipeline, and four hardware multiplier operating modes. The integrated USB peripheral includes an on-chip PHY and pull-up resistors; code can implement HID, CDC, or vendor-class stacks directly. The 10-bit ADC is shared across eight internal and up to twelve external channels through the analog mux, while the DMA engine can stream ADC conversions directly into memory without CPU intervention. Typical applications include USB human-interface devices such as keyboards, mice, and game controllers; portable medical and wellness peripherals; industrial sensor nodes and data loggers; low-power metering; and battery-powered instrumentation that needs an MCU + USB in a single chip. The wide I/O count and integrated analog make it a good fit when an external ADC or signal-conditioning chain would otherwise inflate the BOM. When designing with this part, follow the TI MSP430x5xx Family User's Guide for power-management sequencing, especially the wake-from-LPM transitions and the USB suspend current budget. Reserve the exposed thermal pad for soldering to a ground copper pour to meet the package's thermal-resistance spec and to reduce EMI on the USB DP/DM lines. Use TI's USB Descriptor Tool and MSP430 USB Developers Package firmware to accelerate stack bring-up. This page synthesizes distributor pricing from DigiKey/Mouser/LCSC, verified same-family drop-in alternatives, and practical design notes for USB-aware embedded systems that are not always consolidated in the manufacturer datasheet.

詢價 聯絡我們
MSP430F5510CY - 25MHz 16-Bit MCU with 32KB Flash | TI
MSP430F5510CY

MSP430F5510CY - 25MHz 16-Bit MCU with 32KB Flash | TI

The Texas Instruments MSP430F5510CY is a 25 MHz, 16-bit mixed-signal microcontroller with 32KB of Flash memory, 4KB of SRAM, a 10-bit ADC, comparator, DMA, UART, SPI, I2C, USB, and a hardware multiplier. The MSP430F5510CY ordering code identifies a die-sale form of the MSP430F5510 family rather than a leaded or surface-mount package. A mixed-signal microcontroller is an integrated circuit that combines a programmable digital controller with analog measurement or comparison functions. In the product hierarchy, the MSP430F5510 belongs to the MSP430 mixed-signal microcontroller family, which is a type of 16-bit embedded processor and system-on-chip. Its combination of low-power-oriented control, serial interfaces, USB connectivity, and analog peripherals allows sensing and control tasks to be consolidated in compact embedded systems. The principal verified specifications are a 25 MHz maximum clock, 32KB Flash organized as 32K x 8, 4KB SRAM, and a 10-bit ADC. The device also provides a comparator, DMA controller, UART, SPI, I2C, USB interface, and hardware multiplier. These resources support applications that require periodic analog sampling, event-driven data transfer, low-rate communication, or multiplication-intensive control without requiring a separate analog front end for every function. The MSP430F5510 uses the MSP430 CPUXV2 architecture and belongs to the MSP430F5xx mixed-signal family. DMA can move data independently of the CPU, while the hardware multiplier accelerates multiplication tasks. The parallel availability of UART, SPI, and I2C permits a designer to connect sensors, displays, storage devices, and other embedded modules while retaining USB for a host-oriented interface. Exact ADC timing, USB details, clock configuration, and electrical limits should be confirmed in the manufacturer datasheet before final design release. Typical uses include industrial sensor nodes, compact USB-connected data collectors, building and equipment controls, low-power monitoring equipment, and mixed-signal instruments. In an analog-monitoring design, the 10-bit ADC can acquire sensor signals while the comparator handles threshold events and DMA transfers results into SRAM. UART, SPI, or I2C can then connect the controller to local peripherals, while USB provides a higher-level connection when required. The most important design consideration for the MSP430F5510CY is that CY is a die-sale device rather than a finished, pin-defined package. Its footprint, assembly process, bonding method, die orientation, and exposed features therefore require direct coordination with the assembly provider. Engineers must also verify clock, memory, USB, analog, and power requirements against the MSP430F5510 datasheet and validate the assembled board before production. This page consolidates the verified manufacturer specifications, current distributor pricing reference, die-sale packaging information, application guidance, and the documented absence of a confirmed drop-in replacement. It also distinguishes verified facts from package-specific information that cannot be inferred from the bare-die ordering code.

詢價 聯絡我們
MSP430F5519IPN - 25MHz 128KB Flash USB MCU | Texas Instruments (Tape & Reel)
MSP430F5519IPN

MSP430F5519IPN - 25MHz 128KB Flash USB MCU | Texas Instruments (Tape & Reel)

The Texas Instruments MSP430F5519IPN is a 25 MHz, 16-bit mixed-signal microcontroller with 128KB of flash memory, 8KB of SRAM, USB, and extensive serial connectivity in an 80-pin LQFP package. It operates from a low 1.8 V to 3.6 V supply range and supports temperatures from -40°C to +85°C, making it suitable for compact embedded systems that need low power consumption and multiple communication interfaces. The MSP430 is an ultra-low-power RISC microcontroller family designed around a 16-bit CPU, efficient register architecture, and multiple low-power operating modes. These characteristics make the MSP430F5519 appropriate for battery-powered measurement, communications, industrial control, and portable equipment where energy efficiency is a primary design constraint. Key features include a 25 MHz CPU, 128KB flash, 8KB SRAM, 63 I/O pins, a comparator, DMA, UART, SPI, I²C, USB, timers, and a hardware multiplier. The integrated connectivity and mixed-signal resources reduce the need for external peripheral devices while providing flexible interface options for sensors, actuators, and communication modules. The device uses the MSP430 CPUXV2 core, a 16-bit RISC architecture with 16-bit registers and constant generators intended to improve code efficiency. Its operating range of 1.8 V to 3.6 V supports low-voltage embedded designs, while the 80-LQFP package provides a conventional surface-mount footprint with a large number of accessible I/O pins. Typical applications include USB-connected control systems, low-power data acquisition, industrial instrumentation, sensor networks, portable measurement equipment, and embedded communications products. The combination of USB, UART, SPI, I²C, DMA, timers, comparator, and hardware multiplier allows designers to connect sensors, storage, displays, and host systems without building a complex peripheral network. When designing around the MSP430F5519IPN, verify the complete pinout, supply requirements, clock configuration, and peripheral multiplexing against the manufacturer datasheet. Decoupling, USB routing, and low-power mode entry require careful PCB and firmware planning, especially when the system combines USB connectivity with battery-operated operation.

詢價 聯絡我們
MSP430F5519IPNR - 25MHz 128KB Flash USB MCU | Texas Instruments
MSP430F5519IPNR

MSP430F5519IPNR - 25MHz 128KB Flash USB MCU | Texas Instruments

The Texas Instruments MSP430F5519IPNR is a 25 MHz, 16-bit mixed-signal microcontroller with 128KB of flash memory, 8KB of SRAM, USB, and extensive serial connectivity in an 80-pin LQFP package. It operates from a low 1.8 V to 3.6 V supply range and supports temperatures from -40°C to +85°C, making it suitable for compact embedded systems that need low power consumption and multiple communication interfaces. The MSP430 is an ultra-low-power RISC microcontroller family designed around a 16-bit CPU, efficient register architecture, and multiple low-power operating modes. These characteristics make the MSP430F5519 appropriate for battery-powered measurement, communications, industrial control, and portable equipment where energy efficiency is a primary design constraint. Key features include a 25 MHz CPU, 128KB flash, 8KB SRAM, 63 I/O pins, a comparator, DMA, UART, SPI, I²C, USB, timers, and a hardware multiplier. The integrated connectivity and mixed-signal resources reduce the need for external peripheral devices while providing flexible interface options for sensors, actuators, and communication modules. The device uses the MSP430 CPUXV2 core, a 16-bit RISC architecture with 16-bit registers and constant generators intended to improve code efficiency. Its operating range of 1.8 V to 3.6 V supports low-voltage embedded designs, while the 80-LQFP package provides a conventional surface-mount footprint with a large number of accessible I/O pins. Typical applications include USB-connected control systems, low-power data acquisition, industrial instrumentation, sensor networks, portable measurement equipment, and embedded communications products. The combination of USB, UART, SPI, I²C, DMA, timers, comparator, and hardware multiplier allows designers to connect sensors, storage, displays, and host systems without building a complex peripheral network. When designing around the MSP430F5519IPNR, verify the complete pinout, supply requirements, clock configuration, and peripheral multiplexing against the manufacturer datasheet. Decoupling, USB routing, and low-power mode entry require careful PCB and firmware planning, especially when the system combines USB connectivity with battery-operated operation.

詢價 聯絡我們
MSP430F5529IPN - 25MHz 128KB Flash USB MCU | Texas Instruments (Tape & Reel)
MSP430F5529IPN

MSP430F5529IPN - 25MHz 128KB Flash USB MCU | Texas Instruments (Tape & Reel)

The Texas Instruments MSP430F5529IPN is a 16-bit ultra-low-power microcontroller featuring the MSP430 CPUXV2 core running at up to 25 MHz. It integrates 128KB of Flash memory, 8KB of SRAM, a 12-bit ADC, comparator, DMA, UART/SPI/I2C, USB 2.0, and a hardware multiplier, all in an 80-pin LQFP (PN) package measuring 12x12 mm. This device is part of the MSP430F55xx family, designed for extended battery life in portable and industrial applications. A microcontroller (MCU) is a compact integrated circuit containing a processor core, memory, and programmable input/output peripherals on a single chip. The MSP430 family is renowned for its ultra-low-power operation, featuring multiple low-power modes that reduce current consumption to microamps, making it ideal for battery-powered devices. The MSP430F5529IPN sits within the MSP430F5xx series, which adds USB connectivity and enhanced analog peripherals while maintaining the low-power heritage of the MSP430 architecture. Key features include 25 MHz CPU speed, 128KB Flash, 8KB SRAM, a 12-bit ADC with up to 16 external channels, a comparator, DMA controller, two USCI modules supporting UART/SPI/I2C, a full-speed USB 2.0 interface with integrated PHY, and a 32-bit hardware multiplier. The device operates from 1.8V to 3.6V and supports a wide temperature range of -40C to +85C. The LQFP-80 package provides 63 I/O pins, enabling complex system integration. The MSP430F5529IPN employs the MSP430 CPUXV2 architecture with a von-Neumann memory layout, offering efficient code density and low power consumption. The integrated USB module supports device, host, and OTG modes, simplifying connectivity in embedded systems. The hardware multiplier accelerates DSP-like operations, while the DMA controller offloads data transfers from the CPU, improving overall system throughput. Typical applications include portable medical devices, smart meters, industrial sensor nodes, USB-based data acquisition systems, and battery-powered IoT endpoints. The combination of low power, USB, and rich analog peripherals makes it a versatile choice for designs requiring extended battery life and connectivity. When designing with this MCU, pay attention to the power supply decoupling and the USB PHY layout to ensure signal integrity. The device supports multiple low-power modes, so configure the clock system and peripherals appropriately to maximize battery life.

詢價 聯絡我們
MSP430F5529IPNR - 25MHz 128KB Flash USB MCU | Texas Instruments
MSP430F5529IPNR

MSP430F5529IPNR - 25MHz 128KB Flash USB MCU | Texas Instruments

The Texas Instruments MSP430F5529IPNR is a 16-bit ultra-low-power microcontroller featuring the MSP430 CPUXV2 core running at up to 25 MHz. It integrates 128KB of Flash memory, 8KB of SRAM, a 12-bit ADC, comparator, DMA, UART/SPI/I2C, USB 2.0, and a hardware multiplier, all in an 80-pin LQFP (PN) package measuring 12x12 mm. This device is part of the MSP430F55xx family, designed for extended battery life in portable and industrial applications. A microcontroller (MCU) is a compact integrated circuit containing a processor core, memory, and programmable input/output peripherals on a single chip. The MSP430 family is renowned for its ultra-low-power operation, featuring multiple low-power modes that reduce current consumption to microamps, making it ideal for battery-powered devices. The MSP430F5529IPNR sits within the MSP430F5xx series, which adds USB connectivity and enhanced analog peripherals while maintaining the low-power heritage of the MSP430 architecture. Key features include 25 MHz CPU speed, 128KB Flash, 8KB SRAM, a 12-bit ADC with up to 16 external channels, a comparator, DMA controller, two USCI modules supporting UART/SPI/I2C, a full-speed USB 2.0 interface with integrated PHY, and a 32-bit hardware multiplier. The device operates from 1.8V to 3.6V and supports a wide temperature range of -40C to +85C. The LQFP-80 package provides 63 I/O pins, enabling complex system integration. The MSP430F5529IPNR employs the MSP430 CPUXV2 architecture with a von-Neumann memory layout, offering efficient code density and low power consumption. The integrated USB module supports device, host, and OTG modes, simplifying connectivity in embedded systems. The hardware multiplier accelerates DSP-like operations, while the DMA controller offloads data transfers from the CPU, improving overall system throughput. Typical applications include portable medical devices, smart meters, industrial sensor nodes, USB-based data acquisition systems, and battery-powered IoT endpoints. The combination of low power, USB, and rich analog peripherals makes it a versatile choice for designs requiring extended battery life and connectivity. When designing with this MCU, pay attention to the power supply decoupling and the USB PHY layout to ensure signal integrity. The device supports multiple low-power modes, so configure the clock system and peripherals appropriately to maximize battery life.

詢價 聯絡我們
MSP430F5632IPZ - 20MHz 256KB Flash MCU | Texas Instruments
MSP430F5632IPZ

MSP430F5632IPZ - 20MHz 256KB Flash MCU | Texas Instruments

Texas Instruments MSP430F5632IPZ is a 16-bit mixed-signal microcontroller operating at up to 20 MHz, with 256 KB of Flash memory, 16 KB of SRAM, and USB connectivity in a 100-pin LQFP package. The device integrates a comparator, DMA controller, UART, SPI, I2C, timers, and a hardware multiplier. An MSP430 mixed-signal microcontroller combines a low-power 16-bit RISC processor with analog and digital peripherals on one device. The MSP430F5632 belongs to the broader MCU hierarchy, where microcontrollers sit between general-purpose processors and application-specific embedded controllers. Its five low-power modes and integrated peripherals are designed for portable measurement, industrial control, communications, and battery-powered instrumentation. The principal specifications include a 20 MHz maximum clock, 256 KB of Flash program memory, and 16 KB of SRAM. The integrated DMA controller supports efficient peripheral transfers, while the hardware multiplier accelerates multiply-accumulate operations. USB, UART, SPI, and I2C interfaces provide several options for host connectivity, sensor interfaces, data acquisition, and external memory or peripheral expansion. The MSP430F5632 uses a powerful 16-bit RISC CPU with 16-bit registers and constant generators. This architecture is suited to control loops that require deterministic peripheral access and mixed analog-digital signal processing. The comparator provides an internal threshold function for sensor signals, reducing the need for external conditioning in suitable measurement designs. Typical uses include industrial sensor nodes, USB-connected acquisition systems, portable medical and laboratory instruments, building-control equipment, and low-power data loggers. The device is particularly appropriate when several communication interfaces, timers, and a hardware multiplier are needed without adding separate interface controllers. PCB implementation should preserve short analog and digital return paths, provide appropriate decoupling at the supply pins, and route high-speed USB signals as a controlled impedance differential pair. Confirm the complete 100-pin assignment and board-management requirements against the manufacturer datasheet before releasing the layout. This page combines the device specifications, pin-compatible family alternatives, interface requirements, and practical integration guidance to support component selection, schematic review, PCB design, sourcing, and lifecycle planning.

詢價 聯絡我們
MSP430F5636IPZ - 20MHz Mixed-Signal MCU | Texas Instruments
MSP430F5636IPZ

MSP430F5636IPZ - 20MHz Mixed-Signal MCU | Texas Instruments

Texas Instruments MSP430F5636IPZ is a 20 MHz mixed-signal microcontroller with 128KB of Flash memory, 16KB of SRAM, a 12-bit ADC, a 12-bit DAC, a comparator, DMA, and USB connectivity. The device is offered in a 100-pin LQFP (PZ) package with a 14 mm by 14 mm body size, making it suitable for compact embedded control systems that require extensive mixed-signal and communications resources. A mixed-signal microcontroller is an embedded processing device that combines a digital CPU with analog conversion and other mixed-signal peripherals. In the product hierarchy, the MSP430F5636IPZ belongs to the MSP430 family of 16-bit RISC microcontrollers and integrates control, measurement, and communication functions into one device. This integration can reduce the number of discrete components required when a system must measure analog signals, generate analog output, and exchange data with a host or peripheral. The headline resources are a 20 MHz operating frequency, 128KB of program Flash, and 16KB of SRAM. Its 12-bit ADC and 12-bit DAC support direct acquisition and generation of analog quantities, while the comparator supports threshold-based signal conditioning. DMA reduces the processing burden associated with data movement, and integrated USB expands the device's connectivity options for configuration, logging, control, or firmware update applications. The MSP430 architecture combines a 16-bit RISC core with low-power operating modes designed for embedded systems that must balance responsiveness and energy use. The MSP430F5636IPZ is particularly useful when analog conversion, direct memory access, and USB are needed in the same package. It belongs to the broader microcontroller and embedded-processing category rather than being a discrete analog or interface component. Typical applications include industrial sensor acquisition, USB-connected data loggers, building and energy monitoring, portable measurement instruments, medical monitoring equipment, and low-power embedded control systems. The combination of 128KB Flash, 16KB SRAM, and mixed-signal peripherals supports moderate firmware workloads, local buffering, control algorithms, and communication protocols without requiring a separate external converter. PCB design should preserve USB signal integrity and provide suitable decoupling near the supply pins. Analog and digital grounds should be connected according to the manufacturer's layout guidance, while high-current output paths and USB routing should be kept away from sensitive analog inputs. Firmware should also use the device's low-power modes when continuous conversion or USB activity is not required. This page combines the manufacturer's key device characteristics with practical application guidance, sourcing instructions, package information, and engineering-oriented design considerations. It is intended to help developers evaluate the MSP430F5636IPZ for embedded mixed-signal designs before beginning schematic capture, firmware development, or PCB layout.

詢價 聯絡我們
MSP430F5637IPZ - 20MHz 16-Bit MCU | Texas Instruments
MSP430F5637IPZ

MSP430F5637IPZ - 20MHz 16-Bit MCU | Texas Instruments

Texas Instruments MSP430F5637IPZ is a 20 MHz mixed-signal microcontroller with a 16-bit RISC CPU, 192KB flash memory, 16KB SRAM, a 12-bit ADC, a 12-bit DAC, comparator, DMA, and USB connectivity. The device is packaged in a 100-pin LQFP (PZ) package and is designed for low-power portable measurement applications. Its integrated mixed-signal peripherals support industrial instrumentation, sensor acquisition, portable test equipment, and connected embedded measurement systems. An MSP430 mixed-signal microcontroller combines a low-power RISC processing core with analog and digital peripherals in one device. The MSP430F5637 belongs to the MSP430F5xx family, where the 16-bit CPU, 16-bit registers, constant generators, and low-power operating modes are optimized for battery-powered measurement equipment. USB and DMA extend the device beyond a basic general-purpose MCU by supporting efficient data transfer and peripheral interaction. Key features include a 20 MHz maximum clock, 192KB of flash memory, 16KB of SRAM, 12-bit ADC and DAC resolution, comparator support, DMA, USB, and five low-power modes. The 100-pin LQFP (PZ) package provides the external signal connections needed for analog inputs, digital interfaces, debug access, clocking, and power management. The mixed-signal architecture allows the MSP430F5637IPZ to process sensor data, perform local control functions, and transfer results without requiring separate analog and digital components. The 12-bit ADC is suitable for monitoring external analog signals, while the DAC can support stimulus generation or signal conditioning in test and measurement systems. DMA can move data between memory and peripherals while the CPU handles control and supervisory tasks. Typical applications include industrial process monitoring, environmental sensing, portable medical measurement, laboratory instrumentation, energy measurement, USB-connected data acquisition, and embedded control systems. The 16-bit architecture and 192KB flash capacity are useful for firmware containing communication stacks, calibration routines, and application-specific signal processing. When designing a PCB, preserve the pin assignments and decoupling requirements defined by the manufacturer datasheet. Pay particular attention to analog supply and reference routing, ADC input impedance, USB signal integrity, crystal or clock connections, and exposed thermal-management requirements. This page combines manufacturer specifications with package, application, sourcing, and replacement guidance for faster engineering evaluation.

詢價 聯絡我們
MSP430F5638IPZ - 20MHz 256KB Flash MCU | Texas Instruments
MSP430F5638IPZ

MSP430F5638IPZ - 20MHz 256KB Flash MCU | Texas Instruments

The Texas Instruments MSP430F5638IPZ is a 20 MHz mixed-signal microcontroller with 256 KB of Flash memory, 16 KB of SRAM, a 12-bit ADC, a 12-bit DAC, USB, DMA, and an on-chip comparator, supplied in a 100-pin LQFP package. It combines a 16-bit RISC CPU with low-power operating modes for portable measurement, industrial control, and USB-connected data-acquisition systems. An ultra-low-power microcontroller is a semiconductor designed to complete control and measurement tasks while minimizing energy consumption. The MSP430 family combines a 16-bit RISC core, 16-bit registers, constant generators, and hardware peripherals in a single mixed-signal device. Its architecture supports portable instruments that must alternate between active processing and low-power standby operation while retaining measurements, control state, and communications. Three headline characteristics distinguish this part. The 20 MHz CPU provides higher processing throughput than slower MSP430 devices, while 256 KB of Flash provides room for application code, boot routines, and firmware updates. The analog signal chain combines a 12-bit ADC and 12-bit DAC, allowing a single device to acquire sensor inputs and generate analog outputs without requiring separate converters. The integrated feature set also includes USB, DMA, and a comparator. USB supports direct connectivity to a host or peripheral system, DMA reduces CPU involvement during data transfers, and the comparator supports threshold detection and basic analog supervision. Texas Instruments identifies the MSP430F5638 family as an ultra-low-power MCU intended for portable measurement applications where low-power modes can extend battery life. Typical implementations include USB-connected sensors, precision data loggers, industrial monitoring nodes, handheld analyzers, and low-power embedded measurement instruments. The 12-bit ADC handles analog sensor conditioning, the DAC supports excitation or output signals, and USB reduces the need for a separate protocol converter when the application uses a standard USB interface. PCB design should preserve the analog signal path and USB signal integrity. Place the ADC and DAC support components close to their associated pins, provide clean reference and supply connections, and route USB differential pairs as a short, symmetric pair on a continuous reference plane. Confirm the exact pin assignments, exposed thermal-pad requirements, and decoupling recommendations in the manufacturer datasheet before layout release. This page combines the manufacturer's device features with a practical drop-in alternative assessment, package-level comparison, and engineering design notes. It highlights where the MSP430F5638IPZ fits in mixed-signal designs and where pin-compatible MCU options can support memory upgrades, production sourcing, or footprint consolidation.

詢價 聯絡我們
MSP430F6633IPZ - 20MHz 128KB Flash MCU | Texas Instruments
MSP430F6633IPZ

MSP430F6633IPZ - 20MHz 128KB Flash MCU | Texas Instruments

The Texas Instruments MSP430F6633IPZ is a mixed-signal 16-bit microcontroller operating at up to 20 MHz, with 128 KB of Flash memory, 16 KB of SRAM, and a 100-pin LQFP package. Its integrated peripherals include a 12-bit ADC, comparator, DMA, UART, SPI, I²C, USB, and support for up to 160 LCD segments. A mixed-signal microcontroller combines a programmable processor core with analog and digital peripherals on one device. The MSP430 belongs to the embedded microcontroller hierarchy and uses the MSP430 CPUXV2 architecture. For connected sensing, instrumentation, industrial control, and human-interface applications, this integration can reduce external component count while keeping firmware, signal acquisition, communications, and display control within one compact platform. The MSP430F6633IPZ provides 128 KB of Flash for program storage and 16 KB of SRAM for working data. Its 20 MHz operating speed supports responsive control and measurement tasks. The 12-bit ADC and analog comparator suit sensor conditioning and threshold detection, while DMA improves data movement between peripherals and memory. UART, SPI, and I²C interfaces support industrial buses, sensors, memories, and external controllers. USB connectivity extends the device beyond isolated embedded control, while the 160-segment LCD capability enables dense local displays. These resources allow a design to combine data acquisition, communications, and graphical feedback without requiring separate interface devices. The 100-pin LQFP package provides ample I/O capacity for mixed-signal boards while supporting a conventional surface-mount assembly process. Typical uses include industrial data-acquisition panels, energy-monitoring equipment, medical instrumentation, environmental sensors, portable measurement systems, and USB-connected embedded controllers. In each case, the ADC and comparator support analog measurement, the DMA and serial interfaces manage data transfer, and the LCD controller can reduce external display-driver requirements. Designers should assign analog, communication, debug, and power pins according to the MSP430F663x pin-description table and preserve the required decoupling and layout guidance in the manufacturer documentation. Verify the selected peripheral instance, alternate-function settings, clock configuration, and USB signal routing in firmware and schematic review before production release. This product page combines the manufacturer specifications, package details, application guidance, and same-family replacement options in a format that supports MCU selection, PCB planning, firmware preparation, and sourcing review.

詢價 聯絡我們
MSP430F6638CY - 20MHz 16-Bit Mixed-Signal MCU | Texas Instruments
MSP430F6638CY

MSP430F6638CY - 20MHz 16-Bit Mixed-Signal MCU | Texas Instruments

The Texas Instruments MSP430F6638CY is a 20 MHz, 16-bit mixed-signal microcontroller with 256KB of Flash memory, 16KB of SRAM, a 12-bit ADC, a 12-bit DAC, a comparator, DMA, USB connectivity, and support for a 160-segment LCD. The device is identified as a die-sale product, so the MSP430F6638CY ordering code is not associated with a standard finished package in the manufacturer product information shown here. A mixed-signal microcontroller combines a digital processor with analog conversion and other peripheral functions on one integrated circuit. The MSP430F6638 belongs to the MSP430F6xx family, whose 16-bit RISC CPUXV2 architecture uses a reduced instruction set designed for efficient embedded control. USB, serial interfaces, DMA, and high-resolution analog peripherals make this device suitable for industrial instrumentation, data acquisition, communications, and control systems where integration can reduce external component count. The MSP430F6638 operates with a 20 MHz maximum clock and provides 256KB of program Flash plus 16KB of SRAM. Its analog resources include a 12-bit ADC and 12-bit DAC, while the integrated comparator supports thresholding and signal monitoring. Additional peripherals include DMA, brown-out detection and reset, power-on reset, PWM, a watchdog timer, and a 160-segment LCD driver. These features support real-time acquisition, local control loops, human-machine interfaces, and firmware-managed peripheral movement. The device provides I2C, IrDA, LINbus, SCI, SPI, UART/USART, and USB connectivity. USB can support a direct host or device-oriented peripheral role, while the serial interfaces allow connection to sensors, transceivers, displays, and external converters. The 74 I/O positions indicated for the MSP430F6638 family provide a broad hardware interface for a platform assembled from bare die or a qualified module. Because MSP430F6638CY is offered as die sale rather than a conventional packaged ordering option, assembly into a finished electronic assembly requires die attach, wire bonding, electrical verification, and a package or substrate designed for the device. The die-sale designation also means that exposed-pad, lead, pinout, and standard package drawings cannot be assigned safely without the bonding map or assembly documentation. For new production designs, engineers should use the MSP430F6638 family documentation, confirm the available memory and peripheral configuration, and plan the analog input conditioning around the ADC resolution. USB signal routing requires controlled impedance and careful placement of protection and bypass components, while firmware should verify reset behavior and watchdog behavior during startup. This product summary consolidates the manufacturer specifications, ordering information, interface capabilities, die-sale constraints, and application guidance needed to evaluate the MSP430F6638CY before beginning an embedded mixed-signal design.

詢價 聯絡我們
MSP430F6721IPN - 25MHz Mixed-Signal MCU | Texas Instruments
MSP430F6721IPN

MSP430F6721IPN - 25MHz Mixed-Signal MCU | Texas Instruments

The Texas Instruments MSP430F6721IPN is a single-phase metering system-on-chip with a 16-bit MSP430 CPU, 25 MHz maximum clock speed, 32 KB of Flash program memory, and 2 KB of RAM. It integrates two Sigma-Delta ADCs, an LCD interface, and a real-time clock in an 80-pin LQFP (PN) package. The device also provides 52 general-purpose I/O pins for metering and peripheral connections. A mixed-signal microcontroller is a semiconductor that combines digital control logic with analog measurement functions. The MSP430F6721 belongs to the hierarchy of mixed-signal MCU, 16-bit RISC microcontroller, embedded controller, and metering SoC. Its Sigma-Delta ADC architecture is intended for extracting useful measurements from slowly changing or heavily quantized analog signals while keeping the external signal chain manageable. Key features include 32 KB of Flash memory, 2 KB of SRAM, a 25 MHz CPU, two integrated Sigma-Delta ADCs, an LCD interface, and a real-time clock. The 80-pin LQFP package provides enough connection capacity for sensor inputs, LCD signals, communications, and metering-system control functions. A 3.6 V low-supply-voltage design supports low-power embedded metering applications. The MSP430 CPU architecture uses a 16-bit RISC instruction set with 16-bit registers and constant generators. Its low-power operating modes are relevant to utility meters and other systems that spend substantial time measuring or waiting between communication intervals. Flash execution, RAM organization, clock behavior, and converter performance should be checked against the operating conditions of the final meter design. Typical uses include single-phase electricity meters, smart energy meters, industrial energy monitors, load-management equipment, and LCD-based metering terminals. The integrated converters suit measurement channels, the real-time clock supports time-based metering functions, and the LCD interface simplifies the connection to a local display. When designing the PCB, reserve clean grounding and short analog paths around the Sigma-Delta ADC inputs, and follow the manufacturer pin-description and layout guidance. Verify ADC source impedance, input filtering, LCD timing, reset behavior, clock configuration, and programming interfaces before releasing the layout. This page combines the exact ordering information, package characteristics, pin-compatible family alternatives, comparison parameters, and implementation guidance needed to evaluate MSP430F6721IPN for a new metering design.

詢價 聯絡我們
MSP430F6723IPZ - 25 MHz Metering MCU | Texas Instruments
MSP430F6723IPZ

MSP430F6723IPZ - 25 MHz Metering MCU | Texas Instruments

The Texas Instruments MSP430F6723IPZ is a 16-bit ultra-low-power mixed-signal microcontroller designed for single-phase metering, with a 25 MHz maximum CPU speed, 64 KB of Flash memory, 4 KB of RAM, and two sigma-delta ADCs. It is housed in a 100-pin LQFP (PZ) package rated for -40 °C to 85 °C. A mixed-signal microcontroller combines a digital processor with analog front-end and energy-measurement peripherals on one device. The MSP430F6xx family belongs to the broader embedded MCU category and provides programmable real-time control for energy meters, utility data concentrators, industrial monitoring systems, and portable measurement equipment. Its integration reduces component count while keeping sensing, computation, display control, and communication functions within one low-power device. Key features include 72 configurable I/O pins, two 16-bit sigma-delta ADCs, LCD drive capability, and an internal real-time clock. The device operates from a 3.6 V low-supply range and is specified at 265 µA/MHz in active mode with all system clocks operating at 8 MHz and 3.0 V. These characteristics support metering designs that must continuously acquire analog energy signals while controlling a segment or matrix LCD. The MSP430 architecture uses a 16-bit RISC core with 16-bit registers and constant generators, supporting efficient metering algorithms and compact firmware. Multiple low-power operating modes help reduce energy consumption when the meter is idle, while the real-time clock allows time-of-use measurement and load-profile timing without an external clock component. Typical applications include single-phase electricity meters, smart grid endpoint equipment, industrial energy monitors, and low-cost data loggers with LCD displays. The two sigma-delta channels are particularly relevant to current and voltage sensing, where oversampled conversion and digital filtering improve signal resolution before calculations are performed by the CPU. When laying out a meter board, reserve isolated analog routing for the sigma-delta inputs and keep LCD segment, crystal, and high-current drive connections away from the measurement front end. Confirm the complete pin-assignment table in the manufacturer datasheet before routing, especially for the exposed ground and supply pins in the 100-pin LQFP footprint. This page organizes the device specifications, verified alternatives, metering application guidance, and PCB-level design considerations to support faster component selection and board bring-up.

詢價 聯絡我們
MSP430F6725IPZ - 25MHz Metering MCU | Texas Instruments
MSP430F6725IPZ

MSP430F6725IPZ - 25MHz Metering MCU | Texas Instruments

Texas Instruments MSP430F6725IPZ is a single-phase metering system-on-chip with a 16-bit MSP430 RISC core operating at 25 MHz, 128 KB of Flash memory, 4 KB of RAM, two Sigma-Delta ADCs, an LCD interface, and a real-time clock. The device is packaged in a 100-lead LQFP (PZ) measuring 14 mm by 14 mm and is identified as an industrial-temperature-grade component. A mixed-signal microcontroller is an integrated circuit that combines a digital processor with analog measurement and interface functions. Within the product hierarchy, the MSP430F6725 belongs to the MSP430 mixed-signal MCU family and is purpose-built for metering systems. Its Sigma-Delta ADC channels, LCD support, and RTC reduce the external component count required for energy-measurement instruments, while the MSP430 architecture provides deterministic low-power operation. Principal device characteristics include 25 MHz maximum clock operation, 128 KB of programmable Flash, 4 KB of RAM, and two 24-bit Sigma-Delta ADCs with integrated analog-to-digital converters for high-resolution measurement. The LCD interface supports segmented display products, while the real-time clock provides timekeeping for energy meters, industrial counters, and low-duty-cycle sensing nodes. A 100-pin LQFP package provides the analog, display, communications, and general-purpose signal connections required by multi-function metering designs. The MSP430 CPUXV2 uses a 16-bit RISC architecture with 16-bit registers and constant generators. Its mixed-signal architecture places precision analog conversion close to the digital control logic, supporting measurement systems that must acquire low-frequency analog signals while maintaining predictable response and power consumption. The five low-power operating modes associated with the MSP430 platform help balance measurement duty cycle against standby current in battery-assisted or energy-limited instruments. Typical uses include single-phase electricity meters, utility load-monitoring terminals, industrial energy meters, solar and power-distribution monitoring equipment, and LCD-based sensor nodes. The integrated LCD interface is particularly useful in compact instruments that display consumption values locally, while the two ADC channels support current-voltage signal acquisition when paired with suitable external sensing and conditioning networks. PCB design should treat analog inputs, digital interfaces, and LCD outputs as separate functional groups, while keeping the MCU supply decoupling and reference connections close to their associated pins. Because the LQFP package provides a large number of external connections, use the manufacturer pin-description table when assigning nets. Firmware must also account for the ADC settling, calibration, and gain-correction requirements of precision metering systems. This page consolidates the manufacturer device description, distributor availability information, package details, and family cross-references into one engineering reference. It also organizes practical design considerations, specification comparisons, and qualified same-footprint alternatives so engineers can evaluate the MSP430F6725IPZ before committing a PCB layout or production BOM.

詢價 聯絡我們
MSP430F6733IPZ - 16-Bit Metering MCU with 3 ADCs | Texas Instruments
MSP430F6733IPZ

MSP430F6733IPZ - 16-Bit Metering MCU with 3 ADCs | Texas Instruments

Texas Instruments MSP430F6733IPZ is a 16-bit mixed-signal microcontroller and single-phase metering SoC featuring three sigma-delta ADCs, a 25 MHz MSP430 CPU, 64 KB of Flash memory, and 4 KB of RAM in a 100-pin LQFP package. It integrates an LCD driver, real-time clock, DMA controller, hardware multiplier, four 16-bit timers, and four enhanced universal serial communication interfaces. A mixed-signal microcontroller combines a digital control processor with analog measurement resources on one device. The MSP430 belongs to the low-power MCU hierarchy, combining a 16-bit RISC CPU, mixed-signal peripherals, and energy-conscious design in a single integrated circuit. This integration is especially useful in electricity meters, industrial sensing systems, and equipment that must acquire precision analog measurements while controlling communications and displays. The MSP430F6733IPZ provides three high-performance 24-bit sigma-delta ADCs and one 10-bit ADC. Its four enhanced universal serial communication interfaces comprise three eUSCI_A modules and one eUSCI_B module, supporting serial communication and external-interface requirements. Four 16-bit timers, DMA, a hardware multiplier, an RTC with alarm capabilities, and an integrated-contrast LCD driver reduce the need for external components in metering designs. The device uses a 16-bit MSP430 RISC core operating at up to 25 MHz and includes 64 KB of Flash plus 4 KB of RAM. Its mixed-signal architecture separates precision measurement from general-purpose digital processing, while sigma-delta conversion is appropriate for slowly changing sensor signals in energy-metering and industrial applications. The integrated RTC supports time-based measurement, scheduling, and alarm functions. Typical uses include single-phase electricity meters, smart-grid terminal equipment, industrial process monitors, energy-management terminals, and LCD-based instrumentation. The three sigma-delta channels enable concurrent or sequential analog acquisition, while the LCD driver supports local meter-display designs. Serial interfaces provide a path to communications peripherals, and DMA can move sampled data with limited CPU intervention. PCB design should account for analog and digital return paths around the metering inputs, decoupling requirements for each supply rail, exposed thermal and ground-pin assignments, and the 14 mm by 14 mm LQFP footprint. Use the pin-description and layout guidance in the manufacturer datasheet when assigning tracks and planning analog isolation. This page consolidates the MSP430F6733IPZ metering architecture, package details, application guidance, parameter comparisons, and practical replacement considerations into a focused engineering reference.

詢價 聯絡我們
MSP430F6734AIPNR - 16-bit 96KB Flash Metering SoC | Texas Instruments
MSP430F6734AIPNR

MSP430F6734AIPNR - 16-bit 96KB Flash Metering SoC | Texas Instruments

The Texas Instruments MSP430F6734AIPNR is a single-phase metering system-on-chip (SoC) built around the 16-bit MSP430 CPUXV2 core running at up to 25 MHz, integrating 96 KB Flash and 4 KB RAM in an 80-pin LQFP (PN) package measuring 12 x 12 mm. It is purpose-engineered for metrology and energy-meter front-ends, combining three independent 24-bit sigma-delta analog-to-digital converters, an on-chip real-time clock, hardware LCD driver, and the ultra-low-power MSP430 architecture to deliver years of battery life on a single lithium cell. Background: A metering SoC is a class of mixed-signal microcontroller optimized for accurate measurement of line-voltage and line-current waveforms in single- or poly-phase electricity meters. Within the broader power-management IC hierarchy, the metering SoC sits alongside analog front-ends (AFEs), metrology coprocessors, and standard MCUs, but uniquely combines the metering-specific sigma-delta data path, reference, and LCD segment drive into a single low-power die. This integration eliminates the need for a dedicated metrology AFE companion chip and reduces BOM count. Key differentiating features include the three 24-bit sigma-delta ADCs with built-in programmable gain amplifiers, dedicated tamper-detection input pins for anti-tamper designs, hardware RTC with calendar function, integrated segmented LCD driver supporting up to 320 segments, and the MSP430 CPUXV2 core offering multiple low-power modes (LPM3, LPM4) with sub-microamp standby current. The 96 KB Flash supports full application firmware plus IEC 62053-22 calibration tables. Technical depth: The three sigma-delta ADCs are paired with on-chip voltage reference and gain stages, enabling simultaneous sampling of phase voltage, phase current, and neutral current with effective number of bits (ENOB) suitable for Class 0.2 or Class 0.5 meters per IEC 62053. The 25 MHz CPUXV2 core provides ample headroom for FFT-based harmonic analysis up to the 63rd harmonic while remaining in active mode only during measurement windows. Typical applications include single-phase residential electricity meters, smart energy monitoring sockets, energy-harvesting IoT sensors, prepayment meters, and battery-backed tamper-detecting metering nodes. The integrated LCD driver eliminates a separate driver chip and reduces cost in display-equipped designs. Compared with a discrete MCU + AFE solution, the SoC approach reduces PCB area by approximately 40% and BOM cost. Design consideration: When laying out the PCB, keep the analog sigma-delta traces short and symmetric to avoid degrading effective resolution, place the 32.768 kHz crystal within 5 mm of the XIN/XOUT pins, and provide a solid ground plane under the device to minimize noise coupling into the metrology inputs. This page synthesizes distributor pricing, drop-in alternative MPNs, and design guidance not consolidated in the manufacturer datasheet, supporting rapid component selection and second-sourcing decisions.

詢價 聯絡我們
MSP430F6734IPZ - 25MHz Mixed-Signal Metering MCU | Texas Instruments
MSP430F6734IPZ

MSP430F6734IPZ - 25MHz Mixed-Signal Metering MCU | Texas Instruments

Texas Instruments MSP430F6734IPZ is a 16-bit mixed-signal metering system-on-chip with a 25 MHz MSP430 CPUXV2 core, 96 KB of Flash memory, 4 KB of SRAM, and three sigma-delta ADCs in a 100-pin LQFP (PZ) package. The device operates from a 1.8 V to 3.6 V supply and is designed for single-phase energy-metering applications. A mixed-signal metering SoC is a specialized microcontroller that combines digital control, precision analog measurement, display support, and communication peripherals in one device. In the product hierarchy, the MSP430F6734 belongs to the MSP430 mixed-signal MCU family and integrates energy-metering signal acquisition with an embedded real-time control processor. This integration reduces the component count required for a metering design while supporting measurement and control functions on the same board. The headline features are a 25 MHz CPU frequency, 96 KB of Flash program memory, 4 KB of RAM, and three sigma-delta analog-to-digital converters. The sigma-delta ADCs are particularly relevant to metering designs because they perform analog signal conversion for measured electrical quantities. The manufacturer identifies the device as a single-phase metering SoC with LCD support and a real-time clock, making it suitable for systems that need local measurement, display handling, timekeeping, and embedded control. The CPUXV2 architecture uses 16-bit registers and supports efficient mixed-signal firmware execution at 25 MHz. Flash is organized as 96K x 8 bits, while the 4 KB SRAM provides working memory for measurement processing, calibration values, communications buffers, and display handling. Because the device integrates both metering-specific and general-purpose control functions, firmware must carefully budget RAM and avoid unnecessary background processing when low-power behavior is important. Typical applications include single-phase electricity meters, smart energy meters, industrial energy-monitoring equipment, load-control terminals, and metering boards with local LCD indication. The integrated real-time clock supports time-stamped measurement records, while the LCD capability enables compact meter interfaces without requiring a separate display controller. The three sigma-delta ADC channels also make the device suitable for multi-channel current or voltage acquisition when the selected analog front end supports those measurements. The primary design consideration is analog signal-chain implementation. Component selection, input filtering, protection, reference stability, and isolation must support the metering accuracy required by the finished instrument. Layout should also keep sensitive analog inputs away from high-current switching paths and digital interface activity. Firmware validation should include startup calibration, measurement accuracy, watchdog behavior, communications recovery, and display timing before deployment in the field. This page combines verified product parameters, practical metering-application guidance, a drop-in-focused comparison, and design notes that help engineers evaluate the MSP430F6734IPZ beyond a basic distributor specification summary.

詢價 聯絡我們
MSP430F6736AIPN - 25MHz Metering SoC MCU 128KB Flash | TI
MSP430F6736AIPN

MSP430F6736AIPN - 25MHz Metering SoC MCU 128KB Flash | TI

The Texas Instruments MSP430F6736AIPN is a 16-bit ultra-low-power microcontroller SoC designed for single-phase electricity metering, integrating three independent 24-bit Sigma-Delta ADCs, an LCD driver, real-time clock (RTC), 128KB of Flash, and 8KB of RAM in an 80-pin LQFP (PN) package. It runs the MSP430 CPUXV2 core at up to 25 MHz and operates from 2.5V or 3.3V supplies across -40C to +85C, with rich connectivity including I2C, IrDA, LINbus, SCI, SPI, and UART/USART. A metering SoC (System-on-Chip) is a microcontroller that integrates application-specific analog front-end peripherals - in this case, three precision Sigma-Delta analog-to-digital converters - directly onto the same silicon as the CPU, memory, and display drivers. This topology eliminates the need for an external ADC chip in single-phase energy-meter products, reducing BOM cost and PCB area. The MSP430F6736AIPN sits inside TI's MSP430F6xx metering family, which extends from the broader MSP430 ultra-low-power MCU lineage into the power-measurement domain. Synonyms commonly used in the trade include 'metering MCU', 'energy-meter SoC', and 'e-meter microcontroller'. Key differentiating features of the MSP430F6736AIPN include its 128KB of in-system programmable Flash (sufficient for storing calibration tables, metrology algorithms, and display fonts), an integrated segmented-LCD driver that eliminates external LCD bias-generation hardware, the three 24-bit Sigma-Delta ADCs which simultaneously sample voltage and current channels for class-0.2 or class-0.5 energy accuracy, and ultra-low-power modes that allow the entire meter to draw under 4 mA active while continuously metering. Technically, the device combines a 16-bit RISC MSP430 CPUXV2 core with hardware multiplier, an embedded RTC with calendar, brown-out reset, supply-voltage supervisor, watchdog timer, and multiple timer/capture modules. The three SD24 ADCs achieve effective resolution suitable for IEC 62053-22 class-0.2 meters, and the integrated LCD driver supports up to 320 segments in 8-mux mode. The 80-pin LQFP package exposes all analog and digital pins, with the PN suffix identifying a 12x12 mm body. Typical applications include single-phase residential electricity meters, smart-plug energy monitors, in-home display panels, sub-metering for solar inverters, and industrial power-monitoring controllers. The combination of three SD ADCs and an LCD driver makes the part a true single-chip solution for IEC-compliant class meters. When designing with this device, place the crystal and the SD24 RC components as close to the respective pins as the layout allows, route the analog and digital grounds as separate nets joined at a single point near the IC, and follow TI's 'Single-Phase Metering with the MSP430F6736A' reference design for ADC gain calibration. This page consolidates distributor pricing, drop-in package-matched alternatives, application notes, and design guidance that go beyond a single datasheet table, giving engineers a faster path from datasheet to working single-phase meter prototype.

詢價 聯絡我們
MSP430F6736AIPNR - 128KB Flash 16-Bit Metering SoC | TI
MSP430F6736AIPNR

MSP430F6736AIPNR - 128KB Flash 16-Bit Metering SoC | TI

The Texas Instruments MSP430F6736AIPNR is a 16-bit RISC ultra-low-power single-phase metering system-on-chip (SoC) with three independent 24-bit sigma-delta ADCs, an integrated LCD driver, real-time clock, 128 KB Flash and 8 KB RAM, packaged in an 80-pin LQFP (PN) at 12x12 mm. The CPU core runs at up to 25 MHz and the device supports 1.8V-3.6V supply with active-mode current typically in the 200-400 uA/MHz range, suitable for line-powered and battery-aware smart-meter designs. A single-phase metering SoC is a microcontroller with on-chip analog front-end and LCD driver, purpose-built to perform metrology calculations (RMS voltage, RMS current, active/reactive power, energy) for one residential or commercial phase. The MSP430 family belongs to the broader hierarchy: metering MCU -> mixed-signal microcontroller -> 16-bit microcontroller -> ultra-low-power MCU -> embedded processor. Sigma-delta ADCs offer 24-bit resolution at low sample rates, ideal for current transformers and shunt-based sensing where high dynamic range and noise rejection matter more than bandwidth. Key features include three 24-bit sigma-delta ADCs with differential inputs and programmable gain, hardware AES-256 accelerator on most F67xxA derivatives, integrated LCD driver supporting up to 320 segments, on-chip RTC with calendar, brown-out reset, supply voltage supervisor, and a multi-channel 10-bit SAR ADC on shared pins. Communication interfaces include up to four USCI modules supporting UART/SPI/I2C, IrDA encoder/decoder, and JTAG/SBW for in-system programming and debugging. The MSP430F6736AIPNR uses TI's MSP430 CPUXV2 16-bit RISC core with a 16-bit register file, hardware multiplier, and four-byte fetch. Code execution from Flash at 25 MHz delivers 1.46 DMIPS/MHz (Whetstone equivalent). The architecture trades absolute throughput for energy efficiency: each peripheral can be individually clock-gated, and the CPU enters one of five low-power modes (LPM0-LPM4) with standby currents below 1 uA. Typical applications include single-phase electricity meters (Class 0.2/0.5/1.0 accuracy), smart energy monitoring plugs, solar PV string monitors, appliance line-monitoring controllers, and any battery-aware IoT sensor requiring an integrated LCD. Pin compatibility with the F6736A family allows easy migration to higher-memory or lower-cost variants. When designing with this device, place the three sigma-delta ADC inputs in a quiet ground island and route the analog LDO output to dedicated AVDD pins. The device ships in tape and reel (T&R) and is lead-free / RoHS compliant.

詢價 聯絡我們
MSP430F6736AIPZ - 25MHz MCU, 128KB Flash, 3 SD ADC | TI
MSP430F6736AIPZ

MSP430F6736AIPZ - 25MHz MCU, 128KB Flash, 3 SD ADC | TI

The Texas Instruments MSP430F6736AIPZ is a 16-bit ultra-low-power MSP430 mixed-signal microcontroller engineered for single-phase energy metering, featuring 128KB Flash, 8KB RAM, three independent 24-bit sigma-delta analog-to-digital converters, an integrated LCD driver, and a real-time clock in a 100-pin LQFP (14x14 mm) package. The CPU runs at up to 25 MHz from the MSP430 CPUXV2 core, and the device operates from 1.8V to 3.6V across an industrial -40C to +85C temperature range. According to the manufacturer datasheet, three sigma-delta ADCs were pre-tuned for voltage and current sensing channels typical of class-0.2 metering accuracy. An MSP430 microcontroller is a 16-bit RISC mixed-signal processor from Texas Instruments designed for ultra-low-power embedded applications. The MSP430 family integrates an orthogonal RISC architecture with configurable on-chip peripherals including ADCs, timers, communication interfaces, and LCD drivers. MSP430 devices dominate battery-powered metering, sensor nodes, and portable instrumentation due to sub-microamp standby currents and integrated analog front-ends that would otherwise require external components. Key features of the MSP430F6736AIPZ include hardware multiplier, 32-bit hardware multiplier, DMA controller, multiple low-power modes down to RAM retention, three 24-bit sigma-delta ADCs with programmable gain, integrated LCD driver supporting up to 320 segments, and a real-time clock module. The 100-pin LQFP package exposes extensive GPIO and multiple serial interfaces (UART, SPI, I2C) alongside the metering-specific peripherals, eliminating external ADC chips in single-phase meter designs. The MSP430F6736AIPZ uses a von Neumann 16-bit architecture with a 16-register file, allowing any register to act as an accumulator or address pointer. Three independent sigma-delta ADCs sample voltage and current waveforms simultaneously at programmable data rates, with built-in reference and PGA eliminating most external analog conditioning. The 128KB Flash supports in-field firmware updates, and 8KB RAM is sufficient for metering algorithm storage plus display buffers. Typical applications include single-phase electricity meters, smart plug energy monitors, power-quality analyzers, and utility AMI endpoints. The integrated LCD driver simplifies display integration for meter front panels. Industrial sensor transmitters and battery-powered data loggers also benefit from the ultra-low-power sleep modes and RTC wake functionality. Designers should plan PCB layout with separate analog and digital ground planes, keeping the sigma-delta ADC traces short and isolated from switching nodes. Use low-ESR ceramic bypass capacitors within 5mm of each supply pin. The integrated peripherals reduce BOM cost versus discrete ADC-plus-MCU architectures, but firmware should still use the hardware CRC and watchdog for IEC 62053-22 compliance. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

詢價 聯絡我們
MSP430F6736IPZ - 25MHz Metering MCU | Texas Instruments
MSP430F6736IPZ

MSP430F6736IPZ - 25MHz Metering MCU | Texas Instruments

The Texas Instruments MSP430F6736IPZ is a 16-bit, 25 MHz mixed-signal microcontroller and single-phase metering SoC with 128 KB Flash, 8 KB RAM, three Sigma-Delta ADCs, a 10-bit ADC, an LCD driver, and a real-time clock in a 100-pin LQFP package. The device combines the MSP430 RISC core with three enhanced universal serial communication interface modules, four 16-bit timers, a hardware multiplier, DMA, and alarm-capable RTC functions. A mixed-signal microcontroller is a semiconductor that integrates digital control, analog measurement, and specialized communication peripherals into one device. In the product hierarchy, the MSP430F6736 belongs to the mixed-signal MCU class, the MSP430 family, and the broader microcontroller category. Its integration reduces the component count required for energy-metering and low-power data-acquisition systems while retaining programmable control over analog front ends. The three Sigma-Delta ADCs provide high-resolution measurement channels for metering applications, while the separate 10-bit ADC supports additional analog signal acquisition. Communication resources include three eUSCI_A modules and one eUSCI_B module. Four 16-bit timers support timing, capture, and periodic event generation, while DMA transfers data between memory and peripherals with reduced CPU intervention. The RTC module includes alarm capabilities for scheduled sampling and data logging. The MSP430 CPUXV2 architecture uses a 16-bit RISC instruction set with 16-bit registers and constant generators. At a maximum clock frequency of 25 MHz, the controller provides deterministic execution for protocol handling, measurement control, display updates, and energy calculation. The integrated LCD driver supports segmented metering displays, reducing the need for external display-control hardware in dedicated meter designs. Typical uses include single-phase electricity meters, smart-grid terminal equipment, low-power industrial data loggers, and connected sensing systems. The same device can coordinate analog measurement, communications, local display output, and real-time scheduling. Its broad peripheral integration is particularly useful when both low standby power and deterministic metering behavior are required. PCB design should preserve short, controlled analog-signal paths around the ADC inputs while keeping switching circuitry and high-current routing away from precision measurement channels. Decoupling must follow the Texas Instruments datasheet pin and layout guidance, including the required capacitor values and exposed-pad connection. Firmware should also preserve clock and memory timing assumptions associated with the 25 MHz operating range. This page combines the exact ordering information, technical characteristics, compatible family references, application guidance, and design considerations needed to evaluate the MSP430F6736IPZ for a new metering or low-power embedded design.

詢價 聯絡我們
MSP430F6778IPZ - 25MHz Polyphase Metering SoC | Texas Instruments
MSP430F6778IPZ

MSP430F6778IPZ - 25MHz Polyphase Metering SoC | Texas Instruments

The Texas Instruments MSP430F6778IPZ is a polyphase metering system-on-chip with a 16-bit MSP430 CPU operating at up to 25 MHz, 512 KB of flash memory, 16 KB of RAM, and seven sigma-delta ADCs in a 100-pin LQFP (PZ) package. It is designed for integrated energy-metering and revenue-meter applications requiring multiple precision measurement channels, local display support, real-time timing, communications, and hardware security. A polyphase metering SoC combines a mixed-signal microcontroller with specialized analog measurement resources. Within the device hierarchy, it is a microcontroller and energy-metering SoC rather than a general-purpose processor. Its integrated sigma-delta ADC channels, LCD interface, real-time clock, and AES capability allow a meter designer to consolidate functions that might otherwise require separate analog, timing, display, and security components. The MSP430F6778IPZ provides 512 KB of flash for firmware and metering data, 16 KB of RAM for working memory, seven sigma-delta ADCs, and a 16-bit CPU with a 32-bit multiplier. The CPU can perform energy calculations while supporting tariff management and communications with AMR and AMI modules. An AES capability adds hardware support for protecting metering data or communications. Its integration reduces the number of external components required in a revenue-meter design. The seven ADC channels support multi-phase measurement, while the LCD interface and real-time clock support local displays and time-based functions. The -40°C to +85°C industrial temperature range allows operation across industrial ambient conditions, although the complete system must still be validated for its target enclosure, power supply, and metering accuracy requirements. Typical uses include three-phase smart electricity meters, multifunction energy meters, industrial revenue meters, and AMI communication gateways with local display or load-management functions. The device is particularly useful when metering calculations, timekeeping, secure communications, and human-interface support must coexist in one controller rather than across several discrete components. PCB implementation should preserve the analog performance required by the sigma-delta measurement channels. Analog inputs, reference circuitry, grounding, filtering, and power distribution require careful partitioning so digital switching activity does not degrade measurement accuracy. The 100-pin LQFP footprint also requires adequate solderable land area and careful inspection of fine-pitch leads after assembly. This page combines the device’s manufacturer specifications with practical metering considerations, sourcing guidance, and a conservative drop-in assessment. It also distinguishes verified pin-to-pin replacements from related devices that may differ in electrical function, revision, qualification, or package order code, helping engineers avoid substitutions that cannot be implemented safely on the original PCB.

詢價 聯絡我們
MSP430F6779AIPZ - 25MHz Polyphase Metering SoC, 512KB Flash | TI
MSP430F6779AIPZ

MSP430F6779AIPZ - 25MHz Polyphase Metering SoC, 512KB Flash | TI

The Texas Instruments MSP430F6779AIPZ is a polyphase metering system-on-chip (SoC) based on the MSP430 CPUXV2 16-bit RISC core, integrating seven independent 24-bit sigma-delta analog-to-digital converters (SD24), 512KB of Flash, 32KB of SRAM, an LCD driver, hardware AES, and a real-time clock in a 100-pin LQFP (PZ) package. The MSP430 family is a line of ultra-low-power 16-bit mixed-signal microcontrollers from Texas Instruments built around the MSP430X CPUXV2 core. A metering SoC is a specialized microcontroller that integrates precision analog front-ends (sigma-delta ADCs), energy-measurement firmware support, and communication peripherals into one device - placing analog acquisition, computational logic, and display driving on the same silicon to reduce bill-of-materials cost and to provide calibrated metrology accuracy for billing-grade electricity meters. Key specifications include seven independent 24-bit SD24 sigma-delta ADCs (each with its own input multiplexer and reference buffer), 512KB in-system programmable Flash, 32KB SRAM, a built-in LCD driver capable of up to 320 segments, a hardware AES-128/256 accelerator, a real-time clock (RTC) with calendar mode, and a maximum CPU clock of 25 MHz. The device operates from 1.8 V to 3.6 V, supports five low-power modes drawing as little as 0.1 uA in RTC-only retention, and exposes multiple serial interfaces (UART, SPI, I2C) for communication with metrology front-ends or smart-metering PLC modems. Architecturally, the MSP430F6779AIPZ combines the MSP430X CPUXV2 core with a 32-bit hardware multiplier, a three-channel DMA controller, and the seven SD24 ADCs clocked by a dedicated auxiliary clock domain. The integrated LCD controller supports 4-mux/8-mux displays with charge-pump generation, eliminating the need for an external display driver and reducing overall BOM cost in single-phase and polyphase meter designs. Typical applications include three-phase electricity meters, single-phase smart meters, grid-monitoring equipment, solar inverter monitoring, industrial energy sub-meters, building-automation power meters, and any IEC 62053-22 / IEC 62053-23 class-0.2S or class-0.5S metrology design that requires multiple current and voltage channels with accurate active and reactive energy measurement. Designers should plan for a stable low-noise analog supply (AVCC/AVSS) and a separate digital supply (DVCC/DVSS) with ferrite-isolation between them, since the sigma-delta ADCs are highly sensitive to digital switching noise. Use TI's MSP430 Energia Meter Library and MSP-IQMATHLIB DSP library to accelerate the development of class-0.2S calibration routines. This page synthesizes distributor pricing, drop-in alternatives within the MSP430F67xxA family, and practical hardware design notes not found in the manufacturer datasheet alone.

詢價 聯絡我們