AD506KH - Low-Offset JFET Op Amp | Analog Devices | TO-99-8
MPN: AD506KH ✗ 停產AD506KH 概覽
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The JFET-input topology places the AD506KH in the amplifier family traditionally selected for instrumentation, buffer, and high-impedance signal paths. Within the broader semiconductor hierarchy, the AD506KH is an integrated circuit, an analog amplifier, and specifically a single-amplifier operational amplifier rather than a comparator, reference, or power-management device.
The AD506KH provides one amplifier circuit in an 8-terminal metal-can package. Its advertised maximum input offset voltage is 1500 µV, making offset behavior a principal selection criterion when the amplifier operates near DC. The JFET-input designation indicates the device family’s suitability for circuits handling high-impedance sources, while the single-circuit package allows one amplifier per physical component.
The AD506KH is cataloged as a commercial-grade part that is not AEC-Q100 qualified. Its through-hole TO-99-8 construction supports insertion into suitable sockets, prototyping platforms, legacy analog modules, and selected industrial or instrumentation assemblies. The package has eight physical terminals in a round metal enclosure, which requires care when assigning signal, supply, and compensation connections during schematic capture and PCB layout.
Typical uses include low-frequency instrumentation amplifiers, high-impedance sensor interfaces, analog buffers, waveform conditioning, laboratory measurement circuits, and legacy industrial control modules. In these applications, the single JFET-input amplifier can serve as the active element in non-inverting or inverting signal-conditioning stages. Design selection should account for the device’s 1500 µV maximum offset voltage, supply requirements, gain-bandwidth behavior, input noise, and stability requirements.
The primary design consideration is package-aware implementation. Because AD506KH uses a metal-can TO-99-8 package rather than a modern surface-mount footprint, PCB designs must provide appropriate hole spacing, mechanical clearance, and pin assignments. Designers should also confirm the exact manufacturer pinout, supply voltage, offset trim configuration, and stability requirements against the Analog Devices AD506 documentation before fabrication.
This product record combines package and lifecycle information with practical selection guidance, sourcing instructions, and design notes for engineers maintaining TO-99 analog assemblies. It supports direct comparison with other legacy instrumentation amplifiers while emphasizing that any substitute must be validated for footprint, pinout, supply range, offset voltage, bandwidth, noise, and stability rather than selected by amplifier type alone.
直接替換替代品,適用於 AD506KH — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此產品無可直接替換的替代品。
申請替代品AD506KH 最大額定值與電氣特性
| Amplifier Type | JFET-input operational amplifier |
| Number of Circuits | 1 circuit |
| Number of Terminals | 8 terminals |
| Package Type | TO-99-8 |
| Package Shape | Round |
| Terminal Form | Wire |
| Input Offset Voltage | 1500 µV maximum |
| Temperature Grade | Commercial |
| 安裝類型 | Through-hole |
| MSL 等級 | 3 (168 hours) |
| REACH Status | REACH affected |
| RoHS 狀態 | Non-compliant |
| Qualification | Not qualified |
| HTSUS Code | 8542.33.0001 |
AD506KH round 腳位配置指南
AD506KH(round 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: AD506KH.
請參閱 資料表 以查看完整腳位配置。
典型應用
AD506KH 適用於 6 應用s: High-Impedance Instrumentation Signal Conditioning, Precision Analog Buffering, Laboratory Waveform Conditioning, Legacy Industrial Control Module Repair, Low-Frequency Sensor Interface, Audio and Low-Frequency Active Filters.
High-Impedance Instrumentation Signal Conditioning
The AD506KH fits low-frequency instrumentation paths that use a JFET-input amplifier to present a manageable impedance to a high-impedance sensor. Its advertised maximum input offset voltage of 1500 µV establishes the DC-offset boundary that must be included in measurement-error analysis, particularly when the useful sensor output is small. The amplifier can serve as a non-inverting or inverting conditioning stage around the sensor, with the final gain, bandwidth, and compensation choices validated against the complete AD506 electrical data. Because the device uses an 8-terminal TO-99-8 metal can, the implementation should preserve the legacy footprint and pin assignment rather than assume a generic eight-pin amplifier layout.
Precision Analog Buffering
The AD506KH can be used as an analog buffer when a sensor or reference source cannot drive the next circuit directly. A JFET-input operational amplifier is traditionally suited to impedance buffering because it reduces loading while preserving low-frequency signal integrity. The amplifier’s 1500 µV maximum input offset voltage must be considered when buffering near-DC measurements, since that offset can translate into a meaningful error after gain amplification. Designers should verify input bias current, output drive, noise, and stability from the manufacturer documentation and should use the exact TO-99-8 pinout when creating the buffer stage.
Laboratory Waveform Conditioning
The AD506KH is applicable to laboratory and educational circuits that require a single amplifier in an established legacy instrument. Its JFET-input construction can support measurement interfaces dealing with moderate-to-high source impedance, while the 1500 µV maximum offset voltage provides a defined limit for DC calibration. In a practical circuit, the part can condition a low-frequency sensor waveform before display, digitization, or control. The mechanical choice is important: the round TO-99-8 package requires a compatible socket or through-hole footprint and adequate clearance from adjacent components.
Legacy Industrial Control Module Repair
The AD506KH is useful for maintaining a legacy industrial control module whose original amplifier stage depends on the TO-99-8 footprint, JFET-input topology, and established pinout. In repair and obsolescence-management situations, retaining the original device type can avoid respinning a board and changing a signal path that has already been qualified. The 1500 µV maximum offset voltage should be checked against the module’s acceptable measurement error. Before ordering replacements, confirm the temperature grade, supply configuration, offset-adjust provisions, and compensation values against the circuit documentation.
Low-Frequency Sensor Interface
The AD506KH can serve in a low-frequency sensor interface where a transducer produces a relatively high-impedance signal requiring amplification before an ADC or control input. Its JFET-input architecture is relevant to this use, while the defined 1500 µV maximum offset voltage helps bound the static error introduced by the amplifier. The practical design must evaluate sensor leakage, input bias current, cable capacitance, source noise, and gain stability. TO-99-8 mechanical requirements also make this solution more appropriate for legacy or long-life equipment than for compact new sensor modules.
Audio and Low-Frequency Active Filters
The AD506KH may be used in low-frequency active-filter and audio-buffer circuits where the system benefits from a JFET-input amplifier and a single-circuit metal-can implementation. Its 1500 µV maximum offset voltage can create DC shift that influences headroom in an audio path, so the biasing and filter topology should be evaluated at the lowest intended frequency. The designer should confirm gain-bandwidth product, output swing, noise, and internal or external compensation requirements from the manufacturer documentation. The TO-99-8 footprint makes it particularly relevant to repairs of existing audio and test equipment.
工程參考資料,適用於 AD506KH — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 |
|---|---|
| Brand | Analog Devices |
| Package | TO-99-8 |
| Amplifier Type | JFET-input operational amplifier |
| Number of Circuits | 1 circuit |
| Number of Terminals | 8 terminals |
| Maximum Input Offset Voltage | 1500 µV |
| Temperature Grade | Commercial |
| Mounting Type | Through-hole |
| RoHS Status | Non-compliant |
| REACH Status | REACH affected |
主要差異化特點
- Legacy-compatible JFET-input amplifier architecture (對比Modern surface-mount operational amplifier)
- Defined DC offset limit for legacy signal paths (對比Unqualified generic replacement)
- Single amplifier in an eight-terminal metal can (對比Dual or multi-amplifier modern package)
設計說明
Treat the AD506KH as an eight-terminal TO-99-8 metal-can device and assign every connection from the manufacturer pin-description table. Do not derive pin functions from a generic TO-99 package drawing because the same mechanical outline can be used for different pin arrangements. Preserve the manufacturer-specified pin-1 orientation, provide adequate body clearance, and use a socket when maintenance interchangeability is more important than permanent soldering.
Evaluate source capacitance, input bias current, and the 1500 µV maximum offset voltage together when the amplifier follows a high-impedance sensor. Long PCB traces can increase leakage and stray capacitance, while high closed-loop gain can amplify both offset and bias-related errors. Use short guarded input routes where practical, maintain a suitable return path, and confirm the required compensation method before increasing gain or adding capacitive loading.
The most common failure mode in a replacement is assuming that any one-circuit JFET operational amplifier is interchangeable with the AD506KH. Validate the footprint, terminal functions, supply limits, offset voltage, gain-bandwidth product, bias current, output capability, compensation requirements, and temperature grade. Also account for the MSL 3 classification and its 168-hour floor life, especially when parts have been stored for an extended period before assembly.
合規資訊
The product listings identify the AD506KH as RoHS non-compliant, REACH affected, and not qualified. Lead-free, halogen-free, and conflict-minerals declarations are not identified.