Analog Devices

AD7306JNZ - 5V RS-232/RS-422 Transceiver | Analog Devices

MPN: AD7306JNZ ✓ 啟用中
5 V Vdss EIA RS-232 and EIA RS-422 Rds(on) 24-PDIP Package
MOQ: 1 |

AD7306JNZ 概覽

Analog Devices AD7306JNZ is a 5 V monolithic RS-232 and RS-422 line-driver and receiver interface with three drivers, three receivers, and a 24-pin plastic DIP package. It interfaces TTL signal levels with dual-standard EIA RS-232 and RS-422 signals for industrial, communications, and data-transfer equipment.

A line-driver and receiver is a mixed-signal interface integrated circuit that converts digital logic-level signals into balanced or unbalanced physical-layer signals, while receivers convert incoming line signals back into logic-compatible outputs. The AD7306 belongs to the transceiver hierarchy within interface ICs, combining RS-232 and RS-422 transmission functions in one monolithic device.

The AD7306 contains two RS-232 drivers, one RS-422 driver, one dedicated RS-232 receiver, and one receiver path that can be configured for either RS-232 or RS-422 operation. This mixed architecture allows one package to support point-to-point RS-422 links as well as multiple-driver RS-232 ports. The manufacturer describes the device as a powered line driver/receiver operating from a single 5 V supply.

The three-driver, three-receiver arrangement is useful when a system must support several data directions without using separate interface packages. The configurable receiver path also allows unused RS-422 capability to operate in RS-232 mode, helping designers consolidate functions in equipment with mixed serial-interface requirements. Exact driver slew rate, receiver thresholds, data rates, and supply-current limits should be confirmed in the manufacturer datasheet before finalizing a design.

Typical uses include industrial serial controllers, test equipment, point-to-point data links, instrumentation, and embedded communications equipment. In an RS-422 connection, the transmitter produces a differential signal while the receiver detects the voltage difference between the two conductors. In RS-232 service, the transmitter produces a single-ended, bipolar signal and the receiver detects the corresponding voltage state relative to the receiver reference.

PCB design should preserve the transceiver's pin assignments and provide the decoupling, grounding, and protection appropriate to the implemented standard. Place the supply bypass capacitor close to the device power pin, provide a low-impedance ground reference, and route communications traces away from clocks, switching regulators, and high-current digital returns. External protection may be required when exposed cables present surge or electrostatic-discharge risks.

This product page consolidates the manufacturer interface description, package identification, sourcing information, and engineering guidance into a practical overview. It also distinguishes verified AD7306JNZ characteristics from parameters that require confirmation in the official datasheet, helping engineers evaluate this 5 V RS-232/RS-422 transceiver before layout and release.

直接替換替代品,適用於 AD7306JNZ — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。

此產品無可直接替換的替代品。

申請替代品

AD7306JNZ 最大額定值與電氣特性

Product Type Powered RS-232/RS-422 line driver and receiver
供應電壓 5 V
Supported Standards EIA RS-232 and EIA RS-422
Logic Interface TTL signal levels
Total Driver Count 3
Total Receiver Count 3
RS-232 Drivers 2
RS-422 Drivers 1
Dedicated RS-232 Receivers 1
Configurable Receiver Path 1, configurable as RS-232 or RS-422
封裝 24-PDIP
Package Pin Count 24 pins
安裝類型 Through-hole

AD7306JNZ 24 pins 腳位配置指南

AD7306JNZ(24 pins 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。

AD7306JNZ 的 24 pins 封裝腳位圖

無詳細腳位定義資料: AD7306JNZ.

請參閱 資料表 以查看完整腳位配置。

典型應用

AD7306JNZ 適用於 6 應用s: Industrial Serial Data Links, Point-to-Point RS-422 Communication, RS-232 Port Consolidation, Instrumentation and Test Equipment, Embedded Communication Controllers, Mixed-Standard Data Acquisition.

🏭

Industrial Serial Data Links

The AD7306JNZ suits industrial equipment that must translate between TTL logic and physical serial signals. Its three drivers and three receivers allow several communication paths to be consolidated, while the combination of RS-232 and RS-422 support can serve equipment with different cable-interface requirements. In an RS-422 implementation, the differential driver improves noise immunity over long cable runs, whereas the RS-232 channels support compatibility with single-ended equipment. The 5 V architecture simplifies integration with TTL-based controllers, although the complete channel assignment, logic levels, and timing characteristics must be checked in the manufacturer datasheet before PCB release.

🌐

Point-to-Point RS-422 Communication

The dedicated RS-422 driver in the AD7306JNZ can serve as the transmitting element in a point-to-point balanced connection, while the configurable receiver path can detect a differential RS-422 signal. This arrangement is appropriate for industrial controllers, test systems, and embedded equipment that communicates over a dedicated cable. A balanced interface is especially useful when the link must operate across distances or in an environment containing common-mode interference. The circuit still requires correct termination, protection, grounding, and signal-routing practices, and cable length must be checked against the selected data rate and the receiver’s published performance.

🔧

RS-232 Port Consolidation

The two dedicated RS-232 drivers and two usable RS-232 receiver paths allow the AD7306JNZ to consolidate multiple single-ended serial functions in equipment such as controllers, service interfaces, and diagnostic equipment. Using one transceiver can reduce the number of separate interface packages while maintaining a common 5 V supply. Designers should assign the channels according to the datasheet pinout and account for unused outputs, receiver enable states, and any modem-control functions. External protection may also be needed when the port connects to an external cable because the internal IC is not automatically a complete surge-protection solution.

⚡

Instrumentation and Test Equipment

🧩

Embedded Communication Controllers

An embedded controller with TTL UART outputs can use the AD7306JNZ as the physical-layer interface to RS-232 or RS-422 equipment. The 24-PDIP format can simplify prototype construction and through-hole service access, while the three-driver configuration provides options for multiple command or status links. The configurable receiver allows one channel to support either single-ended or differential operation, which is valuable in equipment designed for more than one host-computer or peripheral configuration. Firmware must handle the corresponding enable and signal states, while the PCB should provide a solid ground reference and appropriately placed bypass capacitance for stable 5 V operation.

📺

Mixed-Standard Data Acquisition

The AD7306JNZ can bridge a data-acquisition or control assembly that must communicate with both RS-232 and RS-422 peripherals. One package includes two RS-232 drivers, one RS-422 driver, one dedicated RS-232 receiver, and a configurable receive channel, allowing designers to avoid completely separate interface ICs. This consolidation can simplify inventory and reduce board area while preserving separate ports for equipment with different electrical conventions. Engineers must still treat each port as an independent signal path, select suitable protection for external cables, and verify that the selected baud rate and cable topology remain within the limits published for the device.

What is the AD7306JNZ?
The AD7306JNZ is a 5 V monolithic RS-232 and RS-422 line-driver and receiver interface packaged in a 24-PDIP. According to the Analog Devices AD7306 product page, it provides two RS-232 drivers, one RS-422 driver, one RS-232 receiver, and one receiver path that can be configured for either RS-232 or RS-422 operation.
How many drivers and receivers does the AD7306JNZ contain?
The AD7306JNZ contains three drivers and three receivers. According to the Analog Devices AD7306 product page, the driver section consists of two RS-232 drivers and one RS-422 driver, while the receiver section consists of one RS-232 receiver and one receiver path configurable as either RS-232 or RS-422.
Which serial standards does the AD7306JNZ support?
The AD7306JNZ supports EIA RS-232 and EIA RS-422 operation from a 5 V supply. According to the manufacturer product page, it interfaces TTL logic levels with both standards, allowing the same mixed-interface device to serve unbalanced RS-232 and differential RS-422 links.
Where can I download the AD7306JNZ datasheet PDF?
The official AD7306JNZ documentation is available from the Analog Devices AD7306 product page at https://www.analog.com/en/products/ad7306.html. The manufacturer page links the product data and datasheet for the AD7306 family, including the electrical characteristics, pin information, and application details needed for design review.
Where is the AD7306JNZ pinout located?
The AD7306JNZ pinout is documented in the pin-description and package-drawing sections of the Analog Devices AD7306 datasheet. The AD7306JNZ ordering code identifies a 24-PDIP package, so engineers should use the 24-pin plastic-DIP drawing and verify every signal, enable, power, and ground connection before laying out the PCB.
What are the key specifications of AD7306JNZ that engineers should know?
The AD7306JNZ is a 5 V, three-driver, three-receiver interface for TTL-to-EIA-RS-232 and TTL-to-EIA-RS-422 conversion. The manufacturer identifies two RS-232 drivers, one RS-422 driver, one dedicated RS-232 receiver, one configurable receiver path, and a 24-PDIP package.
Can AD7306JNZ be used for both RS-232 and RS-422 interfaces?
Yes, the AD7306JNZ can implement both RS-232 and RS-422 interfaces in one package. According to the Analog Devices product page, one receiver path is configurable for either standard, while dedicated driver and receiver sections support the RS-232 and RS-422 functions.
What can replace the AD7306JNZ?
No verified pin-to-pin drop-in replacement for the AD7306JNZ was identified in the available cross-reference information. A functional interface IC with the same driver and receiver counts is not automatically interchangeable because package pin assignments, enable logic, receiver configuration, and RS-232/RS-422 channel assignments must all match.
Is the AD7306JNZ the same as the AD7306AR?
The AD7306AR is not automatically interchangeable with the AD7306JNZ because a genuine drop-in replacement must use the same package footprint and pin mapping. The available comparison information identifies the AD7306AR as an alternative family member, but it does not establish a 24-PDIP pin-to-pin match with AD7306JNZ.
When should I choose AD7306JNZ over a MAX3232-family transceiver?
Choose AD7306JNZ when the design requires both RS-232 and RS-422 capability in one 5 V transceiver with three drivers and three receivers. Choose a MAX3232-family device when a dedicated RS-232-only interface in a smaller surface-mount package is sufficient and verified channel requirements meet the application.
Is AD7306JNZ suitable for industrial serial communication equipment?
AD7306JNZ is architecturally suitable for industrial serial communication equipment requiring TTL-to-RS-232 and TTL-to-RS-422 interfacing at 5 V. Its three-driver, three-receiver organization supports multiple communication channels, although temperature rating, transient immunity, isolation, and cable protection must be confirmed for the deployment.
Where can I buy AD7306JNZ and what is its lead time?
Use the Request a Quote form on this page to request AD7306JNZ availability, current lead time, and an order quotation. The manufacturer lists the AD7306 as a 5 V RS-232/RS-422 interface, and the JNZ ordering code identifies the 24-PDIP package.
What is the price of AD7306JNZ?
Request the current AD7306JNZ quotation through the Request a Quote form on this page. The form allows engineers to confirm unit pricing, stock status, lead time, and requested quantity without relying on a static price that may no longer reflect current inventory or market conditions.
Is AD7306JNZ currently in stock?
Use the Request a Quote form on this page to check current AD7306JNZ stock and allocation status. Availability can vary by package, quantity, and regional supply conditions, so confirm the exact AD7306JNZ ordering code when submitting a request.
What is the lifecycle status of AD7306JNZ?
The AD7306JNZ is treated as active for product planning because Analog Devices continues to present the AD7306 product family on its official product page. For an approved new design, verify ordering status, lifecycle notices, and the availability of the exact JNZ suffix through the Request a Quote form.

工程參考資料,適用於 AD7306JNZ — 比較、設計指引及合規資訊。

選型指南

The AD7306JNZ is the appropriate choice when a 5 V design needs both EIA RS-232 and EIA RS-422 interfaces in one IC, particularly when three transmit and three receive paths can reduce the number of separate interface packages. Its 24-PDIP package is also useful for prototypes and through-hole assembly. A MAX3232-family device may be preferable when the system is limited to RS-232 and uses a compact surface-mount package, because that product family does not provide the same mixed RS-232/RS-422 channel organization. Do not substitute the AD7306AR or AD7306JRZ automatically: the suffix identifies package and related ordering options, and true interchangeability requires identical footprint, pinout, enable logic, and electrical behavior. For new production releases, verify the exact JNZ ordering code, temperature grade, lifecycle status, and cable-protection requirements with the manufacturer and through the Request a Quote form.

與替代品比較

參數 本產品
Brand Analog Devices
Package 24-PDIP
Supply Voltage 5 V
Supported Standards EIA RS-232 and EIA RS-422
Driver Count 3
Receiver Count 3
RS-232 Drivers 2
RS-422 Drivers 1
Configurable Receiver Path 1, configurable as RS-232 or RS-422
Logic Interface TTL signal levels

設計說明

Assign the AD7306JNZ channels directly from the official pin-description table and preserve the manufacturer's 24-PDIP footprint, including pin-1 orientation and exposed through-hole geometry. Because this device mixes unbalanced RS-232 and differential RS-422 signals, route each interface group according to its topology, connect the transceiver ground reference to the appropriate board ground, and avoid sharing narrow return paths with switching currents.

Confirm the published driver slew rate, receiver thresholds, common-mode rejection, and maximum data rate in the AD7306 datasheet before selecting cable length or baud rate. RS-422 generally benefits from balanced routing and appropriate termination, while RS-232 requires single-ended routing and correct reference grounding. Do not combine signal and return conductors in ways that increase noise pickup or make ground potential differences excessive.

Do not assume that another AD7306 ordering code or another RS-232/RS-422 transceiver is a drop-in replacement. A valid substitution must match the 24-PDIP footprint, all 24 pin assignments, channel direction, enable behavior, receiver configuration, and principal electrical limits. Also determine whether the external connector requires surge or ESD protection beyond the transceiver’s internal capability before connecting field-wired equipment.

Place the 5 V bypass capacitor close to the device’s supply and ground pins and follow the capacitor value and layout guidance in the manufacturer documentation. Keep switching-regulator and high-current return paths away from receiver inputs. If the board also carries RS-232 signals with substantial cable transients, separate the protection network from sensitive logic traces so recovery current does not flow through common ground paths.

合規資訊

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
無鉛
Unknown
無鹵
Unknown
衝突礦產
Unknown

The verified product information identifies a 5 V RS-232/RS-422 interface in a 24-PDIP package but does not provide specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations.

資料驗證日期: 2026-11-18 — 資料由 XAIPART 元件工程團隊驗證及整理

相關搜尋

AD7306JNZ AD7306JNZ datasheet AD7306JNZ datasheet pdf AD7306JNZ pinout AD7306JNZ schematic AD7306JNZ equivalent AD7306JNZ replacement AD7306JNZ cross reference AD7306JNZ footprint Analog Devices AD7306JNZ AD7306JNZ price AD7306JNZ stock

相關元件與詞彙

Analog Devices AD7306JNZ AD7306 RS-232 RS-422 EIA RS-232 EIA RS-422 line driver line receiver transceiver TTL logic interface IC mixed-signal IC single-ended signaling differential signaling 24-PDIP 24-pin plastic DIP through-hole package industrial communication point-to-point link data acquisition common-mode rejection surge protection electrostatic discharge protection
快速報價 RFQ
請填寫完整詳細資料 — 我們的業務團隊將於 24 小時內回覆
料號 製造商 封裝 QTY 目標價格 小計
✓
報價已提交!

我們將於 24 小時內回覆您的電子郵件

1
詢價已提交
2
已收到報價
3
已下單
4
付款
5
已出貨
6
已送達
檢視詢價單詳情