AD7306JNZ - 5V RS-232/RS-422 Transceiver | Analog Devices
MPN: AD7306JNZ ✓ فعالAD7306JNZ نمای کلی
A line-driver and receiver is a mixed-signal interface integrated circuit that converts digital logic-level signals into balanced or unbalanced physical-layer signals, while receivers convert incoming line signals back into logic-compatible outputs. The AD7306 belongs to the transceiver hierarchy within interface ICs, combining RS-232 and RS-422 transmission functions in one monolithic device.
The AD7306 contains two RS-232 drivers, one RS-422 driver, one dedicated RS-232 receiver, and one receiver path that can be configured for either RS-232 or RS-422 operation. This mixed architecture allows one package to support point-to-point RS-422 links as well as multiple-driver RS-232 ports. The manufacturer describes the device as a powered line driver/receiver operating from a single 5 V supply.
The three-driver, three-receiver arrangement is useful when a system must support several data directions without using separate interface packages. The configurable receiver path also allows unused RS-422 capability to operate in RS-232 mode, helping designers consolidate functions in equipment with mixed serial-interface requirements. Exact driver slew rate, receiver thresholds, data rates, and supply-current limits should be confirmed in the manufacturer datasheet before finalizing a design.
Typical uses include industrial serial controllers, test equipment, point-to-point data links, instrumentation, and embedded communications equipment. In an RS-422 connection, the transmitter produces a differential signal while the receiver detects the voltage difference between the two conductors. In RS-232 service, the transmitter produces a single-ended, bipolar signal and the receiver detects the corresponding voltage state relative to the receiver reference.
PCB design should preserve the transceiver's pin assignments and provide the decoupling, grounding, and protection appropriate to the implemented standard. Place the supply bypass capacitor close to the device power pin, provide a low-impedance ground reference, and route communications traces away from clocks, switching regulators, and high-current digital returns. External protection may be required when exposed cables present surge or electrostatic-discharge risks.
This product page consolidates the manufacturer interface description, package identification, sourcing information, and engineering guidance into a practical overview. It also distinguishes verified AD7306JNZ characteristics from parameters that require confirmation in the official datasheet, helping engineers evaluate this 5 V RS-232/RS-422 transceiver before layout and release.
جایگزینهای drop-in برای AD7306JNZ — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
هیچ جایگزین مستقیمی برای این محصول موجود نیست.
درخواست جایگزینAD7306JNZ حداکثر مقادیر مجاز و مشخصات الکتریکی
| Product Type | Powered RS-232/RS-422 line driver and receiver |
| ولتاژ تغذیه | 5 V |
| Supported Standards | EIA RS-232 and EIA RS-422 |
| Logic Interface | TTL signal levels |
| Total Driver Count | 3 |
| Total Receiver Count | 3 |
| RS-232 Drivers | 2 |
| RS-422 Drivers | 1 |
| Dedicated RS-232 Receivers | 1 |
| Configurable Receiver Path | 1, configurable as RS-232 or RS-422 |
| بستهبندی | 24-PDIP |
| Package Pin Count | 24 pins |
| نوع نصب | Through-hole |
راهنمای پیکربندی پین AD7306JNZ 24 pins
پیکربندی پین برای AD7306JNZ (پکیج 24 pins). این قطعه آنالوگ دارای پینهای ورودی، خروجی و تغذیه است. برای پیکربندیهای پین offset null، جبرانسازی و فعالسازی به دیتاشیت سازنده مراجعه کنید. ایدهآل برای مدارهای شرطیسازی سیگنال و تقویتکننده.
داده پینآوت تفصیلی موجود نیست برای AD7306JNZ.
به دیتاشیت برای پیکربندی کامل پینها.
کاربردهای معمول
AD7306JNZ مناسب است برای 6 کاربردs: Industrial Serial Data Links, Point-to-Point RS-422 Communication, RS-232 Port Consolidation, Instrumentation and Test Equipment, Embedded Communication Controllers, Mixed-Standard Data Acquisition.
Industrial Serial Data Links
The AD7306JNZ suits industrial equipment that must translate between TTL logic and physical serial signals. Its three drivers and three receivers allow several communication paths to be consolidated, while the combination of RS-232 and RS-422 support can serve equipment with different cable-interface requirements. In an RS-422 implementation, the differential driver improves noise immunity over long cable runs, whereas the RS-232 channels support compatibility with single-ended equipment. The 5 V architecture simplifies integration with TTL-based controllers, although the complete channel assignment, logic levels, and timing characteristics must be checked in the manufacturer datasheet before PCB release.
پیشنهادی
Point-to-Point RS-422 Communication
The dedicated RS-422 driver in the AD7306JNZ can serve as the transmitting element in a point-to-point balanced connection, while the configurable receiver path can detect a differential RS-422 signal. This arrangement is appropriate for industrial controllers, test systems, and embedded equipment that communicates over a dedicated cable. A balanced interface is especially useful when the link must operate across distances or in an environment containing common-mode interference. The circuit still requires correct termination, protection, grounding, and signal-routing practices, and cable length must be checked against the selected data rate and the receiver’s published performance.
پیشنهادی
RS-232 Port Consolidation
The two dedicated RS-232 drivers and two usable RS-232 receiver paths allow the AD7306JNZ to consolidate multiple single-ended serial functions in equipment such as controllers, service interfaces, and diagnostic equipment. Using one transceiver can reduce the number of separate interface packages while maintaining a common 5 V supply. Designers should assign the channels according to the datasheet pinout and account for unused outputs, receiver enable states, and any modem-control functions. External protection may also be needed when the port connects to an external cable because the internal IC is not automatically a complete surge-protection solution.
پیشنهادی
Instrumentation and Test Equipment
پیشنهادی
Embedded Communication Controllers
An embedded controller with TTL UART outputs can use the AD7306JNZ as the physical-layer interface to RS-232 or RS-422 equipment. The 24-PDIP format can simplify prototype construction and through-hole service access, while the three-driver configuration provides options for multiple command or status links. The configurable receiver allows one channel to support either single-ended or differential operation, which is valuable in equipment designed for more than one host-computer or peripheral configuration. Firmware must handle the corresponding enable and signal states, while the PCB should provide a solid ground reference and appropriately placed bypass capacitance for stable 5 V operation.
پیشنهادی
Mixed-Standard Data Acquisition
The AD7306JNZ can bridge a data-acquisition or control assembly that must communicate with both RS-232 and RS-422 peripherals. One package includes two RS-232 drivers, one RS-422 driver, one dedicated RS-232 receiver, and a configurable receive channel, allowing designers to avoid completely separate interface ICs. This consolidation can simplify inventory and reduce board area while preserving separate ports for equipment with different electrical conventions. Engineers must still treat each port as an independent signal path, select suitable protection for external cables, and verify that the selected baud rate and cable topology remain within the limits published for the device.
پیشنهادی
خلاصه محصولات پیشنهادی
دادههای مرجع مهندسی برای AD7306JNZ — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول |
|---|---|
| Brand | Analog Devices |
| Package | 24-PDIP |
| Supply Voltage | 5 V |
| Supported Standards | EIA RS-232 and EIA RS-422 |
| Driver Count | 3 |
| Receiver Count | 3 |
| RS-232 Drivers | 2 |
| RS-422 Drivers | 1 |
| Configurable Receiver Path | 1, configurable as RS-232 or RS-422 |
| Logic Interface | TTL signal levels |
یادداشتهای طراحی
Assign the AD7306JNZ channels directly from the official pin-description table and preserve the manufacturer's 24-PDIP footprint, including pin-1 orientation and exposed through-hole geometry. Because this device mixes unbalanced RS-232 and differential RS-422 signals, route each interface group according to its topology, connect the transceiver ground reference to the appropriate board ground, and avoid sharing narrow return paths with switching currents.
Confirm the published driver slew rate, receiver thresholds, common-mode rejection, and maximum data rate in the AD7306 datasheet before selecting cable length or baud rate. RS-422 generally benefits from balanced routing and appropriate termination, while RS-232 requires single-ended routing and correct reference grounding. Do not combine signal and return conductors in ways that increase noise pickup or make ground potential differences excessive.
Do not assume that another AD7306 ordering code or another RS-232/RS-422 transceiver is a drop-in replacement. A valid substitution must match the 24-PDIP footprint, all 24 pin assignments, channel direction, enable behavior, receiver configuration, and principal electrical limits. Also determine whether the external connector requires surge or ESD protection beyond the transceiver’s internal capability before connecting field-wired equipment.
Place the 5 V bypass capacitor close to the device’s supply and ground pins and follow the capacitor value and layout guidance in the manufacturer documentation. Keep switching-regulator and high-current return paths away from receiver inputs. If the board also carries RS-232 signals with substantial cable transients, separate the protection network from sensitive logic traces so recovery current does not flow through common ground paths.
اطلاعات انطباق
The verified product information identifies a 5 V RS-232/RS-422 interface in a 24-PDIP package but does not provide specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations.