Analog Devices

AD9100AE - Ultrahigh Speed Monolithic Track-and-Hold | Analog Devices

MPN: AD9100AE ✓ 啟用中
5 V Vdss 1 ceramic leadless chip carrier package Package
MOQ: 1 |

AD9100AE 概覽

The Analog Devices AD9100AE is an ultrahigh-speed monolithic track-and-hold circuit with a 0.02 µs acquisition time, a maximum droop rate of 6000 V/s, and a 5 V nominal supply voltage. It is supplied in a 20-lead ceramic leadless chip carrier, or CLCC, package measuring 9 mm by 9 mm for high-speed analog signal acquisition systems.

A sample-and-hold circuit is an analog signal-processing component that acquires an input voltage during a short acquisition interval and then holds that voltage approximately constant for downstream measurement or conversion. The AD9100 belongs to the sample-and-hold IC category within the broader analog IC hierarchy, where it serves as an interface between a rapidly changing source and a slower ADC, instrumentation amplifier, or control loop. Its ultrahigh acquisition speed makes timing and source-impedance behavior central to system design.

The device provides a 0.02 µs acquisition time, allowing a settling interval of 20 ns when the source and timing conditions meet the operating requirements. Its specified maximum droop rate is 6000 V/s, which characterizes how quickly the held output can move away from its captured level. Operation uses a 5 V nominal power supply, while the industrial temperature grade supports operation from -40°C to +85°C. These characteristics target applications requiring rapid acquisition and short holding intervals rather than precision, long-duration sample-and-hold systems.

The AD9100AE is identified as a monolithic sample-and-hold circuit, meaning its acquisition and holding functions are integrated on one semiconductor device. Its 20-CLCC 9 mm by 9 mm package provides a compact surface-mount implementation, but the exposed ceramic construction and high-speed signal path require careful attention to board layout. The analog input, control signals, reference arrangement, ground return, and output path should be routed with short traces and suitable return paths to preserve the intended acquisition performance.

Typical uses include high-speed data acquisition, pulsed instrumentation, digital oscilloscope input stages, closed-loop control samplers, communications test equipment, and analog-to-digital converter front ends. In each case, the system must command acquisition at the proper time and provide a sufficiently low-impedance source so the AD9100AE can reach its specified acquisition time. The 6000 V/s maximum droop rate also limits the useful holding period in applications where the sampled value must remain stable for subsequent conversion.

A key implementation consideration is the relationship between source impedance, acquisition interval, and settling accuracy. Place the input driver close to the device, keep the analog path compact, and use a ground plane that provides a low-impedance return beneath or adjacent to the signal route. Review the AD9100 datasheet for the complete pin-description table, input range, output structure, reference requirements, and recommended test circuit before finalizing the PCB.

This page consolidates the confirmed AD9100AE operating figures, package information, sourcing details, and engineering guidance into one technical reference. It also distinguishes exact same-family grade alternatives from unsupported cross-brand substitutes and provides selection criteria for engineers deciding whether the 20-lead CLCC device fits a timing-critical acquisition design.

直接替換替代品,適用於 AD9100AE — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。

此系列的變體

與下列產品可直接替換的同系列型號: AD9100AE (相同外形與佔位) — 差異在於 Product Type.

Analog Devices
Product Type: Monolithic track-and-hold amplifier
比較對象 AD9100AE →

AD9100SE

✅ 直接替換 ⚠️ 規格未經驗證
📦 20-CLCC (9x9)
Same AD9100 monolithic track-and-hold core and 20-CLCC footprint; 1 grade-code difference, with a 0% difference in the core acquisition and droop ratings treated for this replacement

📋 參考替代品(不在目錄中)

AD9100JD

✅ 直接替換 ⚠️ 規格未經驗證
Analog Devices
📦 20-CLCC (9x9)
Monolithic track-and-hold amplifier · 13 ns · 16 ns · 30 MSPS · Less than 83 dBfs · -74 dBfs · 250 MHz · Less than 1 ps

聯絡詢價

查看資料表 →

AD9100AD

✅ 直接替換 ⚠️ 規格未經驗證
📦 20-CLCC (9x9)
Same AD9100 monolithic track-and-hold core and 20-CLCC footprint; 1 grade-code difference, with a 0% difference in the core acquisition and droop ratings treated for this replacement

📋 參考替代品(不在目錄中)

AD9100SD3

✅ 直接替換 ⚠️ 規格未經驗證
📦 20-CLCC (9x9)
Same AD9100 monolithic track-and-hold core and 20-CLCC footprint; 1 grade-code difference, with a 0% difference in the core acquisition and droop ratings treated for this replacement

📋 參考替代品(不在目錄中)

AD9100AE 最大額定值與電氣特性

Product Type 1 ultrahigh-speed monolithic track-and-hold circuit
Acquisition Time 0.02 µs
Maximum Droop Rate 6000 V/s
Nominal Supply Voltage 5 V
Minimum Operating Temperature -40°C
Maximum Operating Temperature 85°C
Temperature Grade 1 industrial grade
Package Type 1 ceramic leadless chip carrier package
Package Lead Count 20 leads
Package Body Length 9 mm
Package Body Width 9 mm
Package Shape 1 square package
Terminal Form 1 no-lead terminal form
Mounting Technology 1 surface-mount package
RoHS 狀態 1 RoHS-compliant electronic part

AD9100AE 1 square package 腳位配置指南

AD9100AE(1 square package 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。

AD9100AE 的 1 square package 封裝腳位圖

無詳細腳位定義資料: AD9100AE.

請參閱 資料表 以查看完整腳位配置。

典型應用

AD9100AE 適用於 6 應用s: High-Speed ADC Front Ends, Digital Oscilloscope Input Stages, Pulsed Instrumentation, Communications Test Equipment, Closed-Loop Control Samplers, Industrial Data Acquisition.

⚡

High-Speed ADC Front Ends

The AD9100AE fits an ADC front end when a rapidly changing analog signal must be captured and held for conversion. Its 0.02 µs acquisition time provides a 20 ns acquisition interval, while the 6000 V/s maximum droop rate defines how quickly the captured voltage can depart from its value. Place the sample-and-hold device near the ADC and driver so that source impedance, ADC input capacitance, and propagation delay do not consume the acquisition window. The principal trade-off is droop: a longer conversion period can permit the held output to move, so the system must complete conversion within the error budget implied by the maximum droop rate.

📺

Digital Oscilloscope Input Stages

The AD9100AE can serve the input stage of a digital oscilloscope or wideband measurement instrument where rapid acquisition and controlled droop are important. The 0.02 µs acquisition time supports sampling of fast edges, and the 5 V nominal supply fits a conventional single-supply analog section. Place the device close to the input driver and acquisition clock to minimize delay and reflections. The 6000 V/s maximum droop rate requires the converter to begin acquisition at a repeatable point and complete conversion before the captured level changes by more than the instrument’s vertical-error budget.

🧩

Pulsed Instrumentation

For pulsed instrumentation, the AD9100AE captures a measurement at a defined instant and holds it long enough for slower downstream circuitry to process the result. Its 0.02 µs acquisition time allows the capture command to follow the pulse closely, while the 5 V nominal supply simplifies integration with monolithic analog instrumentation. Route the trigger and hold-control traces away from the sensitive input path, and terminate the source to achieve the acquisition behavior required by the test setup. Droop must be evaluated against pulse repetition rate because successive measurements can require the output to remain valid for a different interval than continuous-wave operation.

🌐

Communications Test Equipment

The AD9100AE is applicable to communications test equipment that must capture burst waveforms or rapidly changing envelopes before conversion and analysis. Its 0.02 µs acquisition time supports high-speed timing, and the 6000 V/s maximum droop rate provides a defined limit for hold-duration planning. Keep the RF or baseband driver close to the AD9100AE and use a continuous ground reference beneath the high-speed input route. The choice between AD9100AE and another AD9100 grade should follow the required temperature range and qualification conditions rather than basic track-and-hold functionality, since all supported family alternatives use the same 20-CLCC architecture.

🏭

Closed-Loop Control Samplers

The AD9100AE can acquire a control-loop variable at a synchronized instant and present it to a slower controller or ADC. The 0.02 µs acquisition time reduces the delay between the sample command and capture of a rapidly varying feedback signal. Place the device close to the feedback driver, maintain a continuous return path, and isolate hold-control traces from the analog input. Because the maximum droop rate is 6000 V/s, loop designers must include sample-and-hold error in the stability and accuracy analysis, especially when control updates occur at a low repetition rate.

🔧

Industrial Data Acquisition

The AD9100AE supports industrial data-acquisition modules that need a short acquisition interval while operating from -40°C to 85°C. The 5 V nominal supply allows integration into a compact 20-CLCC surface-mount design, and the 0.02 µs acquisition time is useful when the monitored signal changes during the command-to-sample interval. Protect the input path from industrial noise, provide local supply bypassing, and use a low-impedance source stage. Validate the maximum 6000 V/s droop rate against the longest conversion and processing interval to ensure that system error remains within the measurement specification.

推薦產品摘要

AD9100AE Analog Devices 用於: High-Speed ADC Front Ends, Digital Oscilloscope Input Stages, Pulsed Instrumentation, Communications Test Equipment, Closed-Loop Control Samplers, Industrial Data Acquisition AD9100SE Same-family grade alternative 用於: High-Speed ADC Front Ends, Closed-Loop Control Samplers AD9100JD Analog Devices 用於: Digital Oscilloscope Input Stages, Industrial Data Acquisition AD9100AD Same-family grade alternative 用於: Pulsed Instrumentation AD9100SD3 Same-family grade alternative 用於: Communications Test Equipment
What is the AD9100AE?
The AD9100AE is an ultrahigh-speed monolithic track-and-hold IC from Analog Devices. It acquires an analog input voltage during a short sampling interval and holds that voltage for downstream processing. The device has a 0.02 µs acquisition time, a maximum droop rate of 6000 V/s, and a 5 V nominal supply voltage. According to the AD9100 manufacturer datasheet, it is offered in a 20-lead CLCC package measuring 9 mm by 9 mm.
What are the key specifications of AD9100AE that engineers should know?
The AD9100AE combines a 0.02 µs acquisition time, 6000 V/s maximum droop rate, and 5 V nominal supply operation in a 20-CLCC 9 mm by 9 mm package. Its industrial temperature grade covers -40°C to 85°C. According to the AD9100 manufacturer datasheet, these figures define a fast, short-hold analog acquisition device intended for timing-sensitive signal capture rather than long-duration precision sampling.
What is the acquisition time of AD9100AE?
The AD9100AE has a specified acquisition time of 0.02 µs, equivalent to 20 ns. According to the AD9100 manufacturer datasheet, acquisition performance depends on the hold command and the source presented to the input. Achieving the stated settling behavior therefore requires an appropriate low-impedance driver and layout that minimizes parasitic resistance and capacitance near the analog input.
What is the maximum droop rate of AD9100AE?
The AD9100AE has a maximum droop rate of 6000 V/s. This parameter describes the rate at which the held output can depart from its captured voltage. According to the AD9100 manufacturer datasheet, droop is an important limiting factor when determining how long a sampled value can be held before downstream circuitry requires another acquisition.
What supply voltage does AD9100AE use?
The AD9100AE uses a 5 V nominal supply voltage. According to the AD9100 manufacturer datasheet, the power-supply section defines the operating conditions for the sample-and-hold circuit. Keep supply-decoupling connections short and use the pin-description table when assigning the power and ground terminals, because the high-speed input path also depends on a low-impedance return.
What package does AD9100AE use?
The AD9100AE is packaged as a 20-lead ceramic leadless chip carrier with a 9 mm by 9 mm body. The DigiKey product listing identifies it as a 20-CLCC sample-and-hold IC, while another distributor record describes the package as square and no-lead. Use the AD9100 manufacturer datasheet land pattern and pin-description table for the PCB footprint.
Where can I download the AD9100AE datasheet PDF?
The AD9100 manufacturer datasheet is accessible through the datasheet archive link on this page and contains the electrical characteristics, ordering information, and application details for the AD9100 grade variants. Search for AD9100AE in the PDF and verify the AD9100AE row when reviewing limits, especially acquisition time, droop rate, supply conditions, and temperature-grade information.
Where can I find the AD9100AE pinout?
Use the pin-description table in the AD9100 manufacturer datasheet to determine every AD9100AE terminal and its function. The confirmed package is a 20-lead CLCC measuring 9 mm by 9 mm, but the individual terminal names are not reproduced in the cited product summaries. Do not infer pin assignments from a generic ceramic package; cross-check numbering against the manufacturer land pattern before routing the PCB.
Can AD9100SE replace AD9100AE?
The AD9100SE is a same-family AD9100 grade variant and is the closest supported replacement candidate for the AD9100AE. It appears in the AD9100 datasheet grade list and shares the monolithic track-and-hold architecture, while its grade code differs from AE. The 20-CLCC footprint and core acquisition behavior are treated as identical, but the specific temperature-grade marking and any grade-specific qualification must be checked before production substitution.
What is the best drop-in replacement for AD9100AE?
The best supported drop-in candidate is AD9100SE because it belongs to the same AD9100 grade family and uses the same 20-lead CLCC architecture. The other same-family alternatives are AD9100JD, AD9100AD, and AD9100SD3. These choices preserve the pinout and core track-and-hold function; the grade suffix still requires procurement and qualification review before replacing the AE device in an existing design.
Is AD9100SE the same as AD9100AE?
AD9100SE and AD9100AE are not identical orderable grade codes, but they are variants of the same Analog Devices AD9100 monolithic track-and-hold family. The confirmed AD9100AE specifications include 0.02 µs acquisition time, 6000 V/s maximum droop rate, and -40°C to 85°C operation. According to the AD9100 manufacturer datasheet, the grade-specific suffixes differ, so qualification requirements should determine whether SE is acceptable.
When should I choose AD9100AE over AD9100SE?
Choose AD9100AE when the exact AE industrial-grade ordering code is required by the product specification, qualification plan, or supply chain. Choose AD9100SE when its grade-specific temperature or qualification requirements satisfy the application and the original AE code need not be retained. According to the AD9100 manufacturer datasheet, both are grade selections within the same monolithic track-and-hold family, but their suffix-specific requirements must still be reviewed.
Is AD9100AE suitable for high-speed ADC front ends?
The AD9100AE is suitable for a high-speed ADC front end when the required hold interval and settling behavior align with its 0.02 µs acquisition time and 6000 V/s maximum droop rate. According to the AD9100 manufacturer datasheet, the circuit is designed for rapid sampling. Source impedance, ADC input capacitance, clock timing, and the allowable droop must be evaluated together in the system design.
What can replace AD9100AE?
AD9100SE, AD9100JD, AD9100AD, and AD9100SD3 are the supported same-family drop-in candidates for AD9100AE. They are identified as AD9100 grade variants in the manufacturer datasheet and are treated as sharing the 20-CLCC footprint and pin-to-pin architecture. No verified cross-brand drop-in equivalent was identified, so a second-source design should not be approved solely from general cross-reference search pages.
Where to buy AD9100AE online and what is the price?
Use the Request a Quote form on this page to request AD9100AE availability, current unit pricing, quantity breaks, and lead time. The confirmed commercial listing identifies the part as in stock at LCSC, but its displayed amount is a starting-price presentation rather than a qualifying quantity-break table. XAIPART therefore does not reproduce a static price figure that could become inaccurate.
What is the lead time and stock status for AD9100AE?
The LCSC listing identifies AD9100AE as an in-stock component, but it does not state a fixed lead time or minimum order quantity in the cited result. Request current stock, lot traceability, and lead time through the Request a Quote form on this page. For production planning, also request the manufacturer’s authorized-channel status and any date-code or traceability requirements.

工程參考資料,適用於 AD9100AE — 比較、設計指引及合規資訊。

選型指南

Choose AD9100AE when the design specifically requires the AE industrial-grade ordering code, a 0.02 µs acquisition time, and operation from -40°C to 85°C. It is well suited to fast ADC front ends, oscilloscope input stages, pulsed instrumentation, communications test equipment, and synchronized control sampling. AD9100SE is the preferred same-family alternative when its grade-specific temperature and qualification requirements meet the product specification. AD9100JD, AD9100AD, and AD9100SD3 may be considered only after their individual grade requirements and supply conditions are reviewed. All four alternatives come from the AD9100 grade family and use the same 20-CLCC architecture. No verified cross-brand drop-in part was identified, so a cross-manufacturer redesign should not be treated as a pin-compatible replacement. For any approved grade substitution, confirm the complete pin description, electrical limits, temperature range, qualification status, and acquisition behavior against the manufacturer datasheet.

與替代品比較

參數 本產品 AD9100SE AD9100JD AD9100AD AD9100SD3
Brand Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices
Package 20-CLCC (9x9) 20-CLCC (9x9) 20-CLCC (9x9) 20-CLCC (9x9) 20-CLCC (9x9)
Product Type Monolithic track-and-hold circuit Monolithic track-and-hold circuit Monolithic track-and-hold circuit Monolithic track-and-hold circuit Monolithic track-and-hold circuit
Acquisition Time 0.02 µs 0.02 µs 0.02 µs 0.02 µs 0.02 µs
Maximum Droop Rate 6000 V/s 6000 V/s 6000 V/s 6000 V/s 6000 V/s
Nominal Supply Voltage 5 V 5 V 5 V 5 V 5 V
Temperature Grade Code AE industrial grade SE grade code JD grade code AD grade code SD3 grade code

主要差異化特點

  • Exact AE industrial-grade ordering option within the AD9100 family (對比AD9100SE)
  • Wide confirmed industrial operating range (對比AD9100JD)
  • Compact 20-CLCC implementation with a 9 mm by 9 mm body (對比AD9100AD)
  • Fast acquisition paired with a defined droop limit (對比AD9100SD3)

設計說明

Do not treat the 0.02 µs acquisition time as independent of the source impedance and load. Review the acquisition specification, hold command timing, input range, and output loading in the AD9100 manufacturer datasheet. The source must charge the device’s internal sampling capacitance quickly enough to meet the intended settling error. Use a nearby low-impedance driver, terminate unused inputs as directed, and measure settling at the system’s operating voltage and temperature rather than relying on a nominal acquisition value alone.

Place the AD9100AE close to the source driver and place the hold-control circuitry away from the analog input route. Keep the input trace short, avoid unnecessary test pads and stubs, and provide a continuous ground reference. The 20-CLCC footprint has fine-pitch ceramic construction, so inspect solder-joint fillets and component placement for manufacturing consistency. Use the manufacturer land pattern rather than deriving dimensions from the 9 mm by 9 mm body size alone.

Calculate the allowable hold interval from the 6000 V/s maximum droop rate and the system’s voltage-error budget. For example, an error budget of 10 mV corresponds to approximately 1.67 µs at the maximum specified droop rate. This is an estimated calculation using 6000 V/s and 0.010 V, not an additional device specification. If the downstream converter requires a longer interval, refresh the sample earlier or select a device with lower droop.

Use the AD9100 manufacturer datasheet to identify supply and ground pins before placing bypass capacitors. Place the closest decoupling capacitor directly across the appropriate supply and ground nodes, and keep the connection loop as small as practical. The cited 5 V nominal supply identifies the operating point but does not establish the permitted minimum and maximum limits or capacitor values, so confirm both in the datasheet before releasing the layout.

合規資訊

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
無鉛
Unknown
無鹵
Unknown
衝突礦產
Unknown

The Veswin product record identifies AD9100AE as a RoHS electronic part. No separate REACH, halogen-free, conflict-minerals, or automotive qualification statement is present in the cited product information.

資料驗證日期: 2026-11-10 — 資料由 XAIPART 元件工程團隊驗證及整理

相關搜尋

AD9100AE datasheet AD9100AE datasheet pdf AD9100AE pinout AD9100AE specifications AD9100AE acquisition time AD9100AE droop rate AD9100AE 20-CLCC AD9100AE equivalent AD9100AE replacement AD9100AE vs AD9100SE AD9100AE price AD9100AE stock Analog Devices AD9100AE AD9100AE application circuit what is AD9100AE

相關元件與詞彙

Analog Devices AD9100AE AD9100SE AD9100JD AD9100AD AD9100SD3 monolithic track-and-hold circuit sample-and-hold IC analog signal acquisition semiconductor acquisition time maximum droop rate hold mode 5 V nominal supply 20-CLCC ceramic leadless chip carrier surface mount 9 mm by 9 mm package industrial temperature grade RoHS high-speed ADC front end digital oscilloscope pulsed instrumentation closed-loop control sampling
快速報價 RFQ
請填寫完整詳細資料 — 我們的業務團隊將於 24 小時內回覆
料號 製造商 封裝 QTY 目標價格 小計
✓
報價已提交!

我們將於 24 小時內回覆您的電子郵件

1
詢價已提交
2
已收到報價
3
已下單
4
付款
5
已出貨
6
已送達
檢視詢價單詳情