AD9611BH - +/-5V Operational Amplifier | Analog Devices
MPN: AD9611BH ✓ 啟用中AD9611BH 概覽
An operational amplifier is an analog integrated circuit that amplifies the difference between its differential inputs while providing high input impedance and low output impedance. Within the broader semiconductor hierarchy, an operational amplifier belongs to the amplifier IC and signal-conditioning categories. It is commonly used to buffer sensors, amplify low-level signals, implement active filters, and drive downstream analog circuitry.
The AD9611BH is identified as a hybrid operational amplifier with one amplifier circuit. Its maximum input offset voltage of 4300 uV is the principal characterized input-error specification in the product listing. A ±5 V supply supports applications using dual-polarity rails, while the 80 mA maximum supply-current rating defines the upper limit for device supply demand. The listed 12-terminal package uses through-hole termination and a square QIP form.
The component is suitable for instrumentation-style signal chains that can tolerate its specified offset-voltage range and operate within the -25°C to +85°C temperature interval. It can also be evaluated for general analog conditioning, buffering, and gain-stage functions where the system designer requires dual-rail operation. Because the available technical listing identifies the amplifier category, offset, supply, temperature, and package characteristics, application suitability should be confirmed against the complete manufacturer datasheet before precision measurements or high-gain operation.
Typical circuit roles include low-level signal amplification, impedance isolation between a sensor and a later processing stage, and active-filter implementation around a balanced signal path. The ±5 V operating capability is particularly useful when the signal can swing in either direction. Designers should also account for input offset when calculating accuracy at low signal amplitudes and should verify output-swing, slew-rate, bandwidth, and noise requirements for the intended gain stage.
For a new design, begin by checking the complete pin description and typical application circuit in the manufacturer datasheet. Pay particular attention to offset voltage, common-mode range, output swing, supply current, and stability when driving capacitive loads. A real prototype should also verify that the 12-terminal package is mechanically compatible with the intended through-hole PCB footprint.
This page consolidates the confirmed AD9611BH electrical, environmental, packaging, and commercial information with engineering-focused application guidance. It also distinguishes exact-MPN price evidence from family listings, provides a clear sourcing path for current quotations, and avoids presenting unverified substitute parts as drop-in replacements.
直接替換替代品,適用於 AD9611BH — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此產品無可直接替換的替代品。
申請替代品AD9611BH 最大額定值與電氣特性
| Amplifier Type | Single general-purpose operational amplifier |
| Maximum Input Offset Voltage | 4300 uV |
| 供應電壓 | +/-5 V |
| Maximum Supply Current | 80 mA |
| 工作溫度範圍 | -25°C to +85°C |
| Number of Terminals | 12 terminals |
| Package Code | QIP (MQIP12) |
| Package Shape | Square |
| 安裝類型 | Through-hole |
| Construction | Hybrid |
| Number of Amplifier Circuits | 1 circuit |
AD9611BH square 腳位配置指南
AD9611BH(square 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: AD9611BH.
請參閱 資料表 以查看完整腳位配置。
典型應用
AD9611BH 適用於 6 應用s: Precision Analog Signal Conditioning, Sensor Signal Buffering, Active Filter Implementation, Test and Measurement Front End, Industrial Control Signal Interface, Audio and Communication Signal Buffering.
Precision Analog Signal Conditioning
The AD9611BH can condition low-level analog signals in instrumentation paths that use balanced ±5 V rails. Its confirmed maximum input offset voltage of 4300 uV provides a defined limit for input-referred error, while the single-amplifier configuration makes it suitable for basic gain, buffering, and active-filter stages. Designers should calculate the resulting output error from offset and then confirm bandwidth, slew rate, input bias current, and common-mode limits in the manufacturer datasheet. Prototype the selected gain against the smallest expected input so that offset, bias current, and noise do not obscure the signal of interest.
推薦
Sensor Signal Buffering
The AD9611BH is suitable as a first-stage buffer when a sensor produces a bipolar signal and the downstream circuit requires reduced loading. Its ±5 V supply supports signals centered around ground, while the 4300 uV maximum input offset voltage must be included in the sensor-path error budget. Confirm input bias current for high-impedance sources and verify the complete input common-mode range before connecting the sensor. A practical implementation should keep the sensor return and amplifier ground at the same reference potential and measure offset at the actual operating temperature.
推薦
Active Filter Implementation
The AD9611BH can participate in an active-filter section when a circuit requires a dual-rail analog amplifier and a conventional through-hole implementation. Its single-amplifier architecture allows one device to realize a non-inverting, inverting, or differential gain function according to the surrounding passive network. Filter stability depends on gain, bandwidth, slew rate, and output loading, none of which is confirmed in the accessible product listing. Verify those parameters in the manufacturer datasheet and simulate the complete filter response before fabrication, especially at the minimum signal level and highest supported frequency.
推薦
Test and Measurement Front End
The AD9611BH can serve as the input amplifier for a bench or embedded measurement front end operating from ±5 V. The confirmed 4300 uV maximum input offset voltage contributes directly to measurement uncertainty, so calibration and input-referred error calculations are essential for small signals. The -25°C to +85°C operating range supports industrial laboratory equipment, while the through-hole MQIP12 package simplifies prototyping and rework. Verify input noise, bandwidth, slew rate, and output swing before specifying it for high-accuracy acquisition, and include thermal settling in calibration routines.
推薦
Industrial Control Signal Interface
The AD9611BH can amplify or buffer a bipolar control signal in industrial equipment that operates from ±5 V. Its single-amplifier organization and -25°C to +85°C specified range fit compact analog interface blocks, although the through-hole package should be checked against the available board area. Confirm the output-current capability, capacitive-load behavior, and saturation characteristics in the manufacturer datasheet. Keep sensitive input routing away from switching nodes and use grounding consistent with the signal reference to prevent the 4300 uV offset limit from becoming a dominant system error.
推薦
Audio and Communication Signal Buffering
The AD9611BH can evaluate a low-frequency buffered signal path when the system uses ±5 V rails and does not require rail-to-rail output. The 4300 uV maximum input offset voltage is a meaningful limitation for very small audio or communications signals and should be included in the channel error budget. Gain-bandwidth product, slew rate, noise, and output swing must be checked in the manufacturer datasheet before use with wideband waveforms. A practical design should establish the signal-return reference, provide suitable passive filtering, and verify distortion and stability at the intended operating amplitude.
推薦
推薦產品摘要
工程參考資料,適用於 AD9611BH — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 |
|---|---|
| Brand | Analog Devices |
| Package | MQIP12 QIP-style through-hole package |
| Number of Terminals | 12 terminals |
| Amplifier Circuits | 1 circuit |
| Supply Voltage | +/-5 V |
| Maximum Supply Current | 80 mA |
| Maximum Input Offset Voltage | 4300 uV |
| Operating Temperature Range | -25°C to +85°C |
| Construction | Hybrid |
| Mounting Type | Through-hole |
主要差異化特點
- Defined single-amplifier configuration (對比No verified drop-in alternative)
- Dual-rail analog operation (對比No verified drop-in alternative)
- Established environmental envelope (對比No verified drop-in alternative)
設計說明
Do not treat the general-purpose category as a complete specification. The confirmed 4300 uV maximum input offset voltage can dominate a low-level measurement, while gain-bandwidth product, slew rate, common-mode range, input bias current, and output swing remain unspecified. Before schematic release, compare every signal-path requirement with the manufacturer datasheet and ensure the complete waveform remains within the device's input and output limits.
The AD9611BH uses a 12-terminal MQIP12 through-hole package rather than a standard 8-pin DIP footprint. Do not assume standard DIP-8 pad locations will accept it. Use the manufacturer package drawing to establish hole spacing, body outline, pin numbering, and keep-out requirements. Confirm connector, transformer, or enclosure clearance before layout because the square package may require more routing space than a conventional narrow DIP.
Place the amplifier close to the source of the signal and keep input interconnects short to reduce pickup and parasitic feedback. For a balanced ±5 V circuit, maintain a low-impedance return path and use the manufacturer's recommended decoupling arrangement. If the gain stage follows a switching converter or relay, preserve separation between sensitive input traces and high-current switching paths. Validate the assembled board for oscillation at the intended gain before production release.
合規資訊
No RoHS, REACH, halogen-free, or conflict-minerals declaration was identified for the exact AD9611BH ordering code. AEC-Q100 is not applicable because this product is an operational amplifier rather than an automotive-qualified device.