AD976AARSZ - 16-Bit 200 kSPS ADC | Analog Devices
MPN: AD976AARSZ ✓ 啟用中AD976AARSZ 概覽
An ADC is a data-acquisition IC that converts an analog input voltage into a digital number. The AD976A belongs to the successive-approximation ADC category, where an internal sample-and-hold circuit, comparator, and switched-capacitor conversion network determine the final 16-bit code. The AD976A combines this conversion mechanism with a parallel digital interface, allowing acquired samples to be read directly by a digital processor, field-programmable logic, or data-capture system.
Key features of the AD976AARSZ include 16-bit resolution, a maximum throughput of 200 kSPS, single 5 V operation, an internal 2.5 V reference, and a parallel output interface. According to the Analog Devices AD976A product information, the converter uses Analog Devices' proprietary BiCMOS process, combining high-performance bipolar devices with CMOS circuitry. Factory calibration minimizes the need for external offset and gain correction in many applications.
The AD976A is related to the AD976 family, but the AD976A has the higher 200 kSPS throughput rate. The manufacturer describes the AD976A as a high-speed, low-power converter, with maximum dissipation listed at 100 mW for the AD976/AD976A family. Its internal reference simplifies system design by removing the need for an external reference source, while the parallel interface requires careful attention to output timing and data-acquisition setup.
Typical uses include closed-loop industrial control, analog sensor interfaces, waveform capture, process monitoring, communications receivers, and laboratory instrumentation. The 16-bit code width provides 65,536 digital output levels, while the 200 kSPS rate supports sampling of relatively slow or medium-bandwidth signals rather than high-definition video or high-frequency radar waveforms.
When laying out a circuit, treat the analog input and digital output paths as separate domains. Place input and reference decoupling capacitors close to their associated pins, route the 16-bit parallel bus over controlled-length traces, and terminate unused digital inputs consistently. The manufacturer datasheet pin-description table should be used when assigning PCB nets and checking the 28-pin SSOP land pattern.
This page combines the manufacturer specifications with practical interface guidance, verified distributor availability information, a package-matched comparison, and design notes focused on decoupling, grounding, and parallel-bus implementation. These engineering details help shorten evaluation time when the AD976AARSZ is being considered for a new 16-bit acquisition channel.
直接替換替代品,適用於 AD976AARSZ — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: AD976AARSZ (相同外形與佔位) — 差異在於 Package, Converter Type, Output Interface, Reference Selection.
AD976AARSZ 最大額定值與電氣特性
| Converter Type | Successive-approximation ADC |
| 解析度 | 16 bit |
| Number of Channels | 1 channel |
| Throughput Rate | 200 kSPS |
| 供應電壓 | 5 V |
| Internal Reference Voltage | 2.5 V |
| Output Interface | Parallel |
| Process Technology | BiCMOS |
| Maximum Power Dissipation | 100 mW |
| 封裝 | 28-pin SSOP |
| 安裝類型 | Surface mount |
| RoHS 狀態 | Compliant |
AD976AARSZ 28-pin ssop 腳位配置指南
AD976AARSZ(28-pin ssop 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: AD976AARSZ.
請參閱 資料表 以查看完整腳位配置。
典型應用
AD976AARSZ 適用於 6 應用s: Industrial Process Control, Precision Sensor Acquisition, Laboratory Instrumentation, Communications Receiver, Waveform and Data Capture, Power and Motor Control.
Industrial Process Control
The AD976AARSZ fits closed-loop industrial control and process-monitoring channels that require 16-bit data at up to 200 kSPS. Its single 5 V supply and internal 2.5 V reference reduce the number of support components around the converter, while the parallel interface can connect directly to control logic. Use it where the sampled bandwidth is moderate rather than high-definition video. Place analog and digital return paths carefully because switch-node coupling can corrupt low-order codes even when the converter itself operates within specification.
推薦
Precision Sensor Acquisition
The AD976AARSZ is suitable for digitizing outputs from pressure, temperature, position, and bridge-based sensors where 16-bit resolution improves the representation of small analog changes. The 200 kSPS throughput allows rapid sampling, while the internal 2.5 V reference simplifies systems that do not require an external precision reference. Keep the sensor excitation and converter return paths separate from digital switching currents to preserve code stability in the least-significant bits.
推薦
Laboratory Instrumentation
Laboratory measurement equipment can use the AD976AARSZ for moderate-rate analog front ends, calibration loops, and stimulus-response systems. The 16-bit code width supports detailed measurement records, and the parallel interface supports direct capture by programmable logic. The design should separate the analog input from the parallel output and clock circuitry, provide local bypass capacitance, and validate timing against the receiving device before increasing sample throughput.
推薦
Communications Receiver
The AD976AARSZ can serve as the conversion stage in communications equipment that must recover a moderate-bandwidth analog signal into digital form. Its 200 kSPS rate is appropriate for baseband or intermediate-frequency channels that do not require multi-megahertz sampling, and the parallel output presents each converted word to digital signal-processing logic. Apply the manufacturer input-range requirements and avoid routing high-energy digital nets beside the analog input.
推薦
Waveform and Data Capture
The AD976AARSZ supports compact waveform-capture and repetitive-sampling systems where 16-bit records are more valuable than very high sample rates. The parallel interface allows acquired samples to be stored in external logic or memory, while the single 5 V supply simplifies portable instrument power designs. Ensure the receiving logic can accept the converter's output timing and use controlled trace routing to prevent data corruption during simultaneous switching.
推薦
Power and Motor Control
The AD976AARSZ can be evaluated for power-monitoring and motor-control feedback paths that need faster and more detailed measurements than a low-resolution control ADC. Its 16-bit resolution captures small changes in voltage, current, or position feedback, and the 200 kSPS throughput supports a moderate control-loop update rate. The converter must be paired with careful analog conditioning, isolated return paths, and timing analysis that accounts for the full parallel-bus acquisition delay.
推薦
工程參考資料,適用於 AD976AARSZ — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | AD976ABRZ |
|---|---|---|
| Package | 28-pin SSOP | 28-pin SSOP |
| Brand | Analog Devices | Analog Devices |
| Resolution | 16 bit | 16 bit |
| Throughput Rate | 200 kSPS | 200 kSPS |
| Number of Channels | 1 channel | 1 channel |
| Supply Voltage | 5 V | 5 V |
| Internal Reference | 2.5 V | 2.5 V |
| Output Interface | Parallel | Parallel |
| Conversion Architecture | Successive approximation | Successive approximation |
| Maximum Power Dissipation | 100 mW for the AD976/AD976A family | 100 mW for the AD976/AD976A family |
主要差異化特點
- Higher conversion rate within the AD976 family (對比AD976)
- Single 5 V supply with an integrated reference (對比AD976ABRZ)
- Direct parallel data acquisition (對比Serial-interface ADCs)
設計說明
Separate the analog input network from the 16-bit parallel output bus and any switching-power circuitry. Place the converter's local bypass capacitors at the associated power and reference pins, and provide a continuous return path under the device where the package construction permits. Review the manufacturer datasheet for the recommended input, reference, and digital-interface layout before releasing the PCB.
Treat the parallel output as a timing-sensitive digital interface. Route the 16 data lines with consistent geometry to the receiving logic, keep clock and data skew within the limits shown in the datasheet, and avoid stubs or unnecessary vias. Validate data-valid setup and hold timing at the receiver rather than assuming that the nominal converter delay is sufficient.
Confirm the analog input range, common-mode requirements, and gain arrangement before applying a sensor signal. The internal 2.5 V reference simplifies the design, but it does not remove the need to observe input-swing limits and reference bypass recommendations. Also verify that the receiving logic and board connector support the full 16-bit width; missing two data lines can create a plausible but incorrect waveform.
合規資訊
RoHS compliance is identified in the product listing. Other environmental and automotive declarations require confirmation from Analog Devices for the exact ordering code.