ADF4360-8BCPZRL - 400 MHz Integer-N VCO Synthesizer | ADI
MPN: ADF4360-8BCPZRL ✓ 啟用中ADF4360-8BCPZRL 概覽
An integer-N frequency synthesizer is a PLL-based timing and RF signal-generation device. Its phase-locked loop compares a divided reference signal with a feedback signal derived from the output, then drives the VCO until the two match. The ADF4360-8 places the synthesizer, VCO, and associated control logic in one package, while external inductors establish the center frequency and allow operation across the 65 MHz to 400 MHz range.
The device is programmed through a simple 3-wire serial interface. Integrated registers control the frequency plan, VCO settings, charge-pump current, and power state, allowing software or firmware to change operating conditions without external frequency-setting components. Its 3.0 V to 3.6 V single-supply operation also simplifies connection to low-voltage RF, clocking, and communications systems.
The external-inductor architecture creates an important design distinction: the synthesizer is not limited to one fixed output frequency. Designers select inductors according to the desired VCO range and then configure the integer-N divider and reference path through the register interface. Correct inductor selection and loop-filter design are central to achieving accurate tuning, acceptable phase noise, and reliable lock behavior.
Typical uses include local oscillators for receivers and transmitters, clock-generation circuits, frequency-hopping systems, and RF test equipment. The 400 MHz upper range also makes the device suitable for industrial wireless links, instrumentation, and intermediate-frequency generation where a programmable synthesizer provides more flexibility than a fixed-frequency oscillator.
When laying out the PCB, use the manufacturer’s pin-description table and reference-layout guidance, connect the exposed pad to the ground plane, and place decoupling and loop-filter components close to their assigned pins. Verify lock, reference stability, spur performance, and VCO tuning range on the assembled board because component tolerance, layout parasitics, and power-supply noise affect final RF performance.
直接替換替代品,適用於 ADF4360-8BCPZRL — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: ADF4360-8BCPZRL (相同外形與佔位) — 差異在於 Device Type, Maximum RF Output Frequency, Package, Package Type, Serial Interface.
ADF4360-8BCPZRL7
✅ 直接替換📋 參考替代品(不在目錄中)
ADF4360-8BCPZ
✅ 直接替換📋 參考替代品(不在目錄中)
ADF4360-8BCPRL
✅ 直接替換聯絡詢價
查看資料表 →ADF4360-8BCPZRL 規格
| Device Type | Integer-N frequency synthesizer and VCO |
| Frequency Range | 65 MHz to 400 MHz |
| Maximum RF Output Frequency | 400 MHz |
| Supply Voltage Range | 3.0 V to 3.6 V |
| Serial Interface | 3-wire |
| VCO Frequency Setting | Set by external inductors |
| Power-Down Function | Supported |
| 封裝 | 24-lead LFCSP with exposed pad |
| Package Type | 24-WFQFN exposed-pad CSP |
| 安裝類型 | Surface mount |
| 工作溫度範圍 | -40°C to +85°C |
| Moisture Sensitivity Level | MSL 3 (168 hours) |
| RoHS 狀態 | RoHS3 compliant |
| REACH Status | Unaffected |
ADF4360-8BCPZRL 24-wfqfn exposed-pad csp 腳位配置指南
ADF4360-8BCPZRL(24-wfqfn exposed-pad csp 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: ADF4360-8BCPZRL.
請參閱 資料表 以查看完整腳位配置。
典型應用
ADF4360-8BCPZRL 適用於 6 應用s: Programmable RF Local Oscillator, RF Clock Generation, Frequency-Hopping Communications, Industrial Wireless Test Equipment, Instrumentation and Measurement, RF Frequency Multiplication.
Programmable RF Local Oscillator
The ADF4360-8BCPZRL is appropriate for a programmable receiver or transmitter local oscillator because it combines an integer-N PLL with a VCO covering 65 MHz to 400 MHz. External inductors set the VCO band, and the 3-wire interface changes the operating configuration through the internal registers. The 3.0 V to 3.6 V supply also suits compact RF subsystems. During design, select inductors for the intended band, apply the manufacturer’s loop-filter approach, and verify both lock range and phase-noise performance across temperature.
推薦
RF Clock Generation
The ADF4360-8BCPZRL can generate a programmable clock from 65 MHz to 400 MHz for RF sampling, conversion, and modulation systems. Its integrated synthesizer and VCO reduce the number of separate frequency-generation blocks, while the 3-wire serial interface allows firmware to update the frequency plan. The design must account for reference jitter, integer-N division spurs, and loop-filter settings. Validate the output stability and unwanted-signal levels at the system clock rather than relying only on nominal frequency accuracy.
推薦
Frequency-Hopping Communications
A frequency-hopping radio can use the ADF4360-8BCPZRL to change operating conditions without replacing the oscillator hardware. Register programming through the 3-wire interface supports automated frequency-plan changes, while the 65 MHz to 400 MHz range covers multiple short-range and industrial RF bands. Hop timing, reference accuracy, and lock settling must be coordinated in firmware. Also inspect the spectrum during each hop to ensure that synthesizer spurs do not interfere with adjacent channels.
推薦
Industrial Wireless Test Equipment
The ADF4360-8BCPZRL supports compact RF signal sources used in industrial wireless test equipment because it covers 65 MHz to 400 MHz from a 3.0 V to 3.6 V supply. A test instrument can program different tones or intermediate frequencies through the serial register interface and use external inductors to optimize the selected band. Stable references and careful exposed-pad grounding are important for repeatable measurements. Confirm phase noise, tuning accuracy, and output level after assembly.
推薦
Instrumentation and Measurement
The ADF4360-8BCPZRL is useful as a programmable source for instrumentation that requires accurate test tones within the 65 MHz to 400 MHz range. Integrating the PLL and VCO into one device simplifies the RF architecture, while register control permits remote or automated adjustment of the output configuration. The reference oscillator and loop-filter components directly influence frequency accuracy and phase noise, so they should follow the manufacturer’s design guidance. Use shielded RF routing and controlled impedance for dependable measurement results.
推薦
RF Frequency Multiplication
The integer-N architecture allows the ADF4360-8BCPZRL to create an output frequency derived from a lower reference through programmable division and multiplication. This is useful when a system has a stable reference but needs a local RF carrier in the 65 MHz to 400 MHz band. The reference-to-output ratio determines both the available channel spacing and phase-noise translation. Design the divider ratios to avoid unwanted spurs, and confirm that every required output frequency has adequate lock margin across operating temperature.
推薦
推薦產品摘要
工程參考資料,適用於 ADF4360-8BCPZRL — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | ADF4360-8BCPZRL7 | ADF4360-8BCPZ | ADF4360-8BCPRL |
|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 24-lead LFCSP with exposed pad | 24-lead LFCSP with exposed pad | 24-lead LFCSP with exposed pad | 24-lead LFCSP with exposed pad |
| Device Type | Integer-N synthesizer and VCO | Integer-N synthesizer and VCO | Integer-N synthesizer and VCO | Integer-N synthesizer and VCO |
| Frequency Range | 65 MHz to 400 MHz | 65 MHz to 400 MHz | 65 MHz to 400 MHz | 65 MHz to 400 MHz |
| Maximum RF Output Frequency | 400 MHz | 400 MHz | 400 MHz | 400 MHz |
| Supply Voltage Range | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V |
| Control Interface | 3-wire serial interface | 3-wire serial interface | 3-wire serial interface | 3-wire serial interface |
| VCO Frequency Setting | External inductors | External inductors | External inductors | External inductors |
| Power-Down Function | Supported | Supported | Supported | Supported |
主要差異化特點
- Integrated integer-N PLL and VCO for the 65 MHz to 400 MHz band (對比ADF4360-8BCPZ)
- Single-chip RF synthesis with external inductor configuration (對比ADF4360-8BCPRL)
- Programmable low-voltage operation (對比ADF4360-8BCPZRL7)
設計說明
Follow the Analog Devices reference layout for the 24-lead LFCSP, connect the exposed pad to the ground plane, and place bypass capacitors close to the supply pins. Keep the VCO tank inductors and their connection paths short because stray inductance can shift the tank frequency and reduce tuning margin. Maintain controlled impedance on RF outputs and avoid routing high-speed digital control signals directly beneath sensitive analog and VCO nodes.
Decouple the 3.0 V to 3.6 V supply so that switching currents from surrounding circuitry do not modulate the VCO control voltage or disrupt phase locking. Place the local capacitors at the package rather than at the supply-source connector, and verify power-down behavior in firmware. The external reference path also requires a clean, low-jitter source if frequency accuracy and phase noise are important.
Do not select an ADF4360 family member solely by the 24-lead package. The ADF4360-8 targets 65 MHz to 400 MHz, while other members cover different frequency bands and can require different tank inductors. Confirm the exact band, external-inductor values, reference frequency, divider range, and register settings from the manufacturer application information before releasing a PCB or production order.
Characterize both desired outputs and unwanted products at the antenna or receiver front end. Integer-N division can create reference-related spurs, and switching power converters can inject noise into the VCO. Use a filtered supply or separate sensitive analog supply region, provide adequate reference isolation, and measure settling time and lock performance over temperature before relying on rapid frequency-hopping operation.
合規資訊
RoHS3 compliant and REACH unaffected according to the component compliance listing. No automotive AEC-Q100 qualification, lead-free statement, halogen-free statement, or conflict-minerals declaration is established for this exact orderable configuration.