ADM3064EARZ - 500 kbps ESD-Protected RS-485 Transceiver | Analog Devices
MPN: ADM3064EARZ ✓ 啟用中ADM3064EARZ 概覽
An RS-485 transceiver is an interface IC that combines a differential line driver, differential receiver, and electrical protection into the physical layer of a multipoint communications bus. Its hierarchy is RS-485 interface transceiver → bus-line transceiver → interface IC → semiconductor. Differential signaling improves noise immunity by transmitting the same signal as complementary voltages and rejecting common-mode noise encountered in industrial environments.
The ADM3064EARZ combines a 3.0 V to 5.5 V operating range with 500 kbps signaling and ±12 kV IEC ESD protection. The 14-lead SOIC package is widely supported by automated assembly and board-layout practices. Its half-duplex architecture allows the same differential pair to support transmitting and receiving when the bus direction is controlled externally. The reported 800 ns maximum transmit delay supports deterministic communication designs operating at the stated 500 kbps class.
The ADM3064E family is designed around a single RS-485 transceiver rather than a multi-channel interface. During transmission, the driver places a differential voltage onto the bus; during reception, the receiver converts the differential bus voltage into a logic signal. A direction-control circuit determines which function is active. The manufacturer evaluation platform EVAL-ADM3064EEBZ uses the same standard 14-lead SOIC footprint and allows the driver and receiver functions to be exercised without external components.
Typical uses include industrial instrumentation, factory automation, building controls, communications equipment, and long-reach RS-485 networks. The 500 kbps rate is appropriate for supervisory links, configuration buses, sensor aggregation, and equipment-to-equipment communication. At lower signaling rates, the same transceiver can serve longer cable runs, although cable length, topology, termination, and data rate must be considered together.
Board design should preserve the transceiver's common-mode operating range and route the differential pair as a controlled impedance pair. Place termination, biasing, protection, and decoupling components close to their associated pins. Avoid long unprotected stubs, maintain consistent return paths, and apply the manufacturer's recommended supply and ground layout. In noise-heavy installations, verify both conducted and radiated immunity rather than relying on ESD protection alone.
This page combines the manufacturer's ADM3064E product information with package, interface, and ordering details for faster component selection. It also provides application guidance, drop-in alternatives, and practical bus-layout considerations that help engineers connect the ADM3064EARZ specifications to a complete RS-485 interface design.
直接替換替代品,適用於 ADM3064EARZ — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: ADM3064EARZ (相同外形與佔位) — 差異在於 Package, Interface Standard, Operating Temperature Range, Product Type, RoHS Status.
ADM3064EBRZ
✅ 直接替換聯絡詢價
查看資料表 →ADM3061EARZ
✅ 直接替換 ⚠️ 規格未經驗證聯絡詢價
查看資料表 →ADM3062EARZ
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
ADM3063EARZ
✅ 直接替換 ⚠️ 規格未經驗證聯絡詢價
查看資料表 →ADM3064ERUZ
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
ADM3064EARZ 規格
| Transceiver Configuration | 1/1 transceiver |
| Interface Standard | EIA-485 RS-485 |
| Driver and Receiver Count | 1 driver and 1 receiver |
| Supply Voltage Range | 3.0 V to 5.5 V |
| Nominal Signaling Rate | 500 kbps |
| High-Speed Mode | 50 Mbps |
| ESD Protection | ±12 kV IEC ESD protected |
| Maximum Transmit Delay | 800 ns |
| 工作溫度範圍 | -40 °C to +85 °C |
| 封裝 | 14-lead SOIC, 0.154 inch (3.90 mm) width |
| 安裝類型 | Surface mount |
| Shipping Package | Tube |
| Terminal Count | 14 terminals |
| RoHS 狀態 | Compliant |
| Evaluation Board Footprint | Standard 14-lead SOIC footprint |
ADM3064EARZ tube 腳位配置指南
ADM3064EARZ(tube 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: ADM3064EARZ.
請參閱 資料表 以查看完整腳位配置。
典型應用
ADM3064EARZ 適用於 6 應用s: Industrial Sensor Aggregation, Factory Automation Control Bus, Building Control Network, Instrumentation and Test Equipment, Telecommunications Power Monitoring, Data Acquisition Backplane.
Industrial Sensor Aggregation
The ADM3064EARZ fits industrial sensor-aggregation links that require one RS-485 driver and one receiver in a 14-lead SOIC package. Its 3.0 V to 5.5 V supply range supports both 3.3 V and 5 V control systems, while the 500 kbps class provides ample bandwidth for periodic temperature, pressure, and level measurements. Place the transceiver between the controller and a twisted differential pair, use a local supply capacitor, and fit termination only at the physical ends of the bus. The ±12 kV IEC ESD rating strengthens the interface against electrostatic discharge, although surge protection and proper grounding remain necessary in severe industrial environments.
推薦
Factory Automation Control Bus
The ADM3064EARZ is appropriate for supervisory and control traffic on factory automation equipment where noise immunity and ESD robustness matter. The differential RS-485 interface reduces susceptibility to common-mode interference relative to a single-ended communications link, and the 500 kbps rate supports equipment status, commands, and diagnostic data. The device can operate from a 3.3 V controller rail or a 5 V industrial rail. Keep the differential trace pair tightly coupled, avoid branch stubs, and use the manufacturer's pin-description table when assigning direction-control, enable, ground, and bus connections.
推薦
Building Control Network
The ADM3064EARZ can connect controllers to distributed building equipment over an RS-485 bus. Its 3.0 V to 5.5 V operating range accommodates low-voltage control electronics, while 500 kbps operation is more than sufficient for HVAC status, lighting control, access equipment, and environmental monitoring. The single-driver, single-receiver arrangement supports half-duplex communication on a multidrop bus. Use consistent 120-ohm termination at selected physical endpoints, establish biasing for an idle network where required, and separate sensitive analog routing from the bus to reduce coupling into building-control measurements.
推薦
Instrumentation and Test Equipment
The ADM3064EARZ suits laboratory and industrial instrumentation that exchanges configuration and measurement data over RS-485. A 500 kbps link allows responsive command-and-response operation without occupying a high-speed differential pair such as USB or Ethernet. The 14-lead SOIC package is convenient for automated assembly, while the ±12 kV IEC ESD protection adds interface robustness in shared industrial cabinets. For sensitive measurements, place analog sections away from the transceiver and bus connector, use a continuous ground reference, and verify that isolation or shield arrangements do not compromise the intended common-mode range.
推薦
Telecommunications Power Monitoring
The ADM3064EARZ can support remote monitoring units that report power-system measurements over an RS-485 communications segment. Its 3.0 V to 5.5 V supply range supports embedded controller platforms, and the 500 kbps class provides sufficient throughput for periodic telemetry and control messages. The half-duplex topology limits physical bus complexity, while the integrated ESD protection helps the transceiver survive electrostatic events encountered during field servicing. Route the bus as a controlled-impedance differential pair, provide a low-impedance return path, and include appropriately coordinated surge protection when the installation is exposed to lightning or severe switching transients.
推薦
Data Acquisition Backplane
The ADM3064EARZ is suitable for a data-acquisition backplane that connects one controller to remote analog and digital measurement modules. The 500 kbps rate supports frequent sampling telemetry when payload sizes remain moderate, and the one-driver, one-receiver architecture fits multidrop half-duplex wiring. Its 3.0 V to 5.5 V range allows placement near either 3.3 V or 5 V backplane electronics. Maintain a continuous reference plane under the pair, keep connectors and protection devices away from sensitive analog nodes, and verify cable length against the selected data rate to avoid signal-integrity degradation.
推薦
推薦產品摘要
工程參考資料,適用於 ADM3064EARZ — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | ADM3064EBRZ | ADM3061EARZ | ADM3062EARZ | ADM3063EARZ | ADM3064ERUZ |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 14-lead SOIC | 14-lead SOIC | 14-lead SOIC | 14-lead SOIC | 14-lead SOIC | 14-lead SOIC |
| Interface Type | RS-485 | RS-485 | RS-485 | RS-485 | RS-485 | RS-485 |
| Mounting Type | Surface mount | Surface mount | Surface mount | Surface mount | Surface mount | Surface mount |
主要差異化特點
- Combines a 500 kbps RS-485 interface with high-level ESD protection (對比ADM3061EARZ)
- Uses a broadly deployable 14-lead SOIC footprint (對比ADM3062EARZ)
- Supports 3.0 V to 5.5 V operation with a reported 800 ns maximum transmit delay (對比ADM3063EARZ)
- Provides a direct same-family order-code path within the ADM3064E family (對比ADM3064EBRZ)
設計說明
Route the RS-485 driver and receiver connections as a tightly coupled differential pair over a continuous reference plane. Avoid adding test-point branches or unused stubs because they create impedance discontinuities and reflections. Keep the pair away from switching-converter inductors, high-current return paths, and crystal clocks. Use symmetrical components for differential filtering or protection so that common-mode conversion does not degrade the received signal.
Do not treat ±12 kV IEC ESD protection as a substitute for surge protection or a complete industrial protection network. The ADM3064EARZ should be used with correct bus topology, suitable cable, controlled grounding, and coordinated protection. Avoid placing termination resistors indiscriminately at every node; termination belongs at the physical ends of the bus. Confirm the fail-safe state and biasing arrangement before operating a multidrop network.
Place the supply-decoupling capacitor immediately adjacent to the transceiver's supply and ground pins, and provide a low-impedance ground return for both logic and bus-current paths. The stated 3.0 V to 5.5 V range covers 3.3 V and 5 V systems, but the system's steady-state and transient voltages must remain inside that range. Validate the design with the manufacturer's recommended capacitor values and switching conditions.
合規資訊
RoHS compliance is indicated for ADM3064EARZ in the component listing. The IEC 60000-4-2 ±12 kV figure is an ESD-protection specification, not an AEC-Q100 qualification.