ADM3068EBRZ - 50 Mbps RS-485 Transceiver | Analog Devices
MPN: ADM3068EBRZ ✓ 啟用中ADM3068EBRZ 概覽
An RS-485 transceiver is an interface integrated circuit that combines a differential line driver and a differential receiver. It belongs to the RS-485 interface family within the broader category of interface ICs, allowing logic-level UART, SPI, or microcontroller signals to travel across a balanced, noise-resistant cable. Full duplex means the transmitter and receiver can operate simultaneously rather than sharing one bidirectional bus in the same way as half-duplex implementations.
Key electrical features include a 3.0 V to 5.5 V supply range, operation from -40°C to +125°C, and ±12 kV IEC-compliant ESD protection on the bus-facing pins. The device supports both 500 kbps and 50 Mbps communication rates, making it suitable for legacy control networks as well as faster data links. Analog Devices also offers a matching EVAL-ADM3068EEBZ evaluation board with a footprint for the ADM3068EBRZ.
The ADM3068E family combines high-speed differential signaling with integrated protection in several space-saving packages, including 10-lead LFCSP, 8-lead and 10-lead MSOP, and 8-lead and 14-lead SOIC_N options. The 14-lead SOIC_N version provides a conventional surface-mount footprint and 0.154-inch lead pitch, simplifying assembly where very small package types would complicate inspection or manual rework.
Typical uses include industrial sensor networks, motor-control systems, factory automation links, building controls, and test equipment requiring a robust balanced interface. The full-duplex architecture can reduce protocol complexity in point-to-point links because separate transmit and receive paths can be active at the same time.
Designers should follow the pin-description and termination guidance in the manufacturer datasheet, including the requirements for bus biasing, common-mode jumper selection, and cable termination. Place the transceiver close to the connector, route the differential pair as a tightly coupled pair, and provide a low-impedance return path to reduce radiated emissions and susceptibility to external interference.
This page combines manufacturer specifications, package and interface details, sourcing information, and practical RS-485 design guidance to help engineers evaluate the ADM3068EBRZ for industrial and embedded communication links.
直接替換替代品,適用於 ADM3068EBRZ — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: ADM3068EBRZ (相同外形與佔位) — 差異在於 RoHS Status.
ADM3068EARZ
✅ 直接替換聯絡詢價
查看資料表 →ADM3068EBRZ 規格
| Product Type | RS-485 Transceiver |
| Supply Voltage Range | 3.0 V to 5.5 V |
| High-Speed Data Rate | 50 Mbps |
| Low-Speed Data Rate | 500 kbps |
| ESD Protection | ±12 kV IEC ESD |
| Duplex Mode | Full Duplex |
| Number of Drivers | 1 |
| Number of Receivers | 1 |
| 工作溫度範圍 | -40°C to +125°C |
| Package Type | 14-Lead SOIC_N |
| Package Width | 3.90 mm |
| Lead Pitch | 0.154 inch |
| 安裝方式 | SMD/SMT |
| Packing Method | Tube |
| Evaluation Board | EVAL-ADM3068EEBZ |
| RoHS 狀態 | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | unknown |
ADM3068EBRZ 3.90 mm 腳位配置指南
ADM3068EBRZ(3.90 mm 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: ADM3068EBRZ.
請參閱 資料表 以查看完整腳位配置。
典型應用
ADM3068EBRZ 適用於 6 應用s: Industrial Sensor and Controller Networks, Factory Automation Equipment Links, Robotics and Motion Control, Building and HVAC Control Systems, Test and Measurement Data Acquisition, Instrumentation and Process-Control Links.
Industrial Sensor and Controller Networks
The ADM3068EBRZ fits point-to-point links between industrial controllers, remote sensor nodes, and actuator modules because it provides a 3.0 V to 5.5 V supply range, full-duplex operation, and ±12 kV IEC ESD protection. The 50 Mbps capability permits rapid transfer of sensor batches, configuration data, and diagnostic packets while the 500 kbps rate supports conventional control traffic. Place the transceiver near the field connector, route the differential pair as a coupled pair, and apply the termination and biasing shown in the manufacturer application circuit.
推薦
Factory Automation Equipment Links
Use the ADM3068EBRZ for high-speed communication between PLCs, motion controllers, production stations, and inspection equipment when the physical layer must tolerate industrial electrical noise. Full-duplex operation allows each station to transmit and receive without shared-bus direction arbitration, while the 50 Mbps rate supports dense telemetry and synchronized machine data. Its -40°C to +125°C operating range supports factory-floor temperature extremes, and the ±12 kV IEC ESD rating strengthens protection at exposed cable interfaces.
推薦
Robotics and Motion Control
The ADM3068EBRZ is appropriate for encoder feedback, motor-command feedback, and joint-controller communication links that require deterministic bidirectional transfer. Its 50 Mbps high-speed mode reduces transfer time for position, velocity, and diagnostic information compared with a 500 kbps-only interface. Full-duplex behavior simplifies the physical layer in point-to-point robot connections, while the narrow-body 14-lead SOIC_N package is practical for compact controller boards and automated assembly.
推薦
Building and HVAC Control Systems
The ADM3068EBRZ can connect room controllers, HVAC equipment, dampers, and supervisory panels over balanced RS-485 wiring. The 3.0 V to 5.5 V operating range allows integration with both 3.3 V microcontrollers and 5 V interface circuits, while full-duplex operation supports continuous command exchange and status reporting. The ±12 kV IEC ESD protection is especially useful where internal boards connect to long field cables, although cable routing, grounding, and surge mitigation still require system-level engineering.
推薦
Test and Measurement Data Acquisition
The ADM3068EBRZ is useful in instruments that transfer digitized measurements, calibration tables, or configuration data between a host and remote acquisition hardware. A 50 Mbps bus rate can shorten transfer time for large waveform and diagnostic payloads, and the 500 kbps mode accommodates low-rate control traffic. The full-duplex arrangement permits simultaneous status monitoring and command traffic, while the 14-lead SOIC_N package supports conventional PCB assembly and rework processes.
推薦
Instrumentation and Process-Control Links
The ADM3068EBRZ supports communication between process transmitters, analyzers, remote I/O, and a central control unit where reliable differential signaling is required. Its full-duplex configuration reduces contention logic, the 50 Mbps mode handles high-volume process data, and the 500 kbps rate remains available for slower legacy equipment. The -40°C to +125°C range suits many industrial environments, and ±12 kV IEC ESD protection adds a useful layer of ruggedness at externally accessible interfaces.
推薦
推薦產品摘要
工程參考資料,適用於 ADM3068EBRZ — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | ADM3068EARZ |
|---|---|---|
| Package | 14-Lead SOIC_N | 14-Lead SOIC_N - same footprint |
| Brand | Analog Devices | Analog Devices |
| Product Type | Full-Duplex RS-485 Transceiver | Full-Duplex RS-485 Transceiver |
| High-Speed Data Rate | 50 Mbps | 50 Mbps |
| Low-Speed Data Rate | 500 kbps | 500 kbps |
| Supply Voltage Range | 3.0 V to 5.5 V | 3.0 V to 5.5 V |
| ESD Protection | ±12 kV IEC ESD | ±12 kV IEC ESD |
| Operating Temperature Range | -40°C to +125°C | -40°C to +125°C |
| Driver and Receiver Count | 1 Driver, 1 Receiver | 1 Driver, 1 Receiver |
| Mounting Style | SMD/SMT | SMD/SMT |
主要差異化特點
- High-speed full-duplex RS-485 in a 14-lead SOIC package (對比ADM3068EARZ)
- Integrated bus-side ESD robustness (對比ADM3068EARZ)
- Dual operating-rate capability (對比ADM3068EARZ)
設計說明
Place the ADM3068EBRZ close to the RS-485 connector and route the two bus conductors as a tightly coupled differential pair. Keep the pair away from switching-regulator outputs, relay contacts, and high-current return paths. Follow the manufacturer evaluation-board layout and datasheet guidance for the common-mode jumper, bus termination, and grounding arrangement. These steps reduce radiated emissions and improve noise immunity in industrial environments.
Do not treat the ±12 kV IEC ESD rating as a substitute for surge protection, isolation, or cable design. ESD protection addresses electrostatic discharge, while transients coupled from field wiring can require separate surge-mitigation components. Verify the complete ordering-code suffix, temperature range, termination configuration, and bus-topology limits in the ADM3068E datasheet before releasing a production design.
Use the termination and fail-safe bias network specified for the selected bus topology, and observe the datasheet limits for common-mode voltage and driver loading. For high-speed operation, avoid stubs, maintain a continuous reference plane, and keep connector transitions short. The 50 Mbps capability provides link margin, but it does not compensate for poor cable topology or uncontrolled board-level reflections.
Decouple the 3.0 V to 5.5 V supply close to the device with the capacitance and placement specified in the manufacturer datasheet. Route the return current through the same reference system used by the transceiver, and keep supply noise out of the sensitive receive path. Verify the supply level, startup behavior, and interface thresholds against the selected system voltage rather than assuming 3.3 V or 5 V compatibility for every configuration.
合規資訊
The ±12 kV IEC ESD rating is an interface protection specification rather than an environmental or material-compliance declaration. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the current manufacturer product documentation or declaration.