ADM6996A2T1 - 10/100 Ethernet Switch Controller | Infineon
MPN: ADM6996A2T1 ✓ 啟用中ADM6996A2T1 概覽
An Ethernet switch controller is an interface IC that manages data traffic between a host processor and physical Ethernet ports. The ADM6996A2T1 belongs to the broader hierarchy of Ethernet controllers, network interface controllers, interface ICs, and semiconductors. Its parallel interface connects the switching functions to a digital host, while its 10/100 Base-T/TX capability supports Fast Ethernet equipment.
The principal identified features are 10/100 Base-T/TX operation, a parallel processor interface, and a 128-BFQFP package. This combination is useful when a system needs an Ethernet interface close to the host logic without relying on an external plug-in module. The unified controller reduces the number of separate network-interface devices required in compact networking equipment.
Technically, the part combines Ethernet switch control and physical-layer interface functionality in one integrated device. The parallel interface provides a direct digital connection to processors, FPGAs, or other embedded controllers, avoiding the serial interface commonly associated with network-on-chip solutions. Its 128-pin quad flat package provides the mixed-signal, power, ground, and digital I/O connections expected in a high-pin-count networking controller.
Typical applications include industrial Ethernet equipment, embedded routers, network interface controllers, factory automation systems, and legacy Fast Ethernet infrastructure. The parallel interface may be especially useful in industrial designs where a processor or FPGA already handles packet processing and only requires a dedicated Ethernet front end.
Designers should assign power, ground, analog Ethernet, clock, management, and parallel data signals according to the manufacturer pin-description table. Because the package exposes 128 connections, careful plane partitioning, solid grounding, and controlled routing around high-speed digital interfaces are essential. Confirm that host logic and the PCB land pattern match the exact ADM6996A2T1 configuration before layout release.
This page organizes the known device identity, package information, sourcing guidance, same-package alternatives, and engineering-selection considerations. It also identifies where detailed electrical limits, clock requirements, register definitions, and absolute-maximum ratings must be confirmed in the manufacturer datasheet before a production design is approved.
直接替換替代品,適用於 ADM6996A2T1 — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
ADM6996HX-AD-T-1
✅ 直接替換📋 參考替代品(不在目錄中)
ADM6996FCX-AC-T-1
✅ 直接替換📋 參考替代品(不在目錄中)
ADM6996LCX-AD-R-1
✅ 直接替換📋 參考替代品(不在目錄中)
ADM6992X-AD-T-1
✅ 直接替換📋 參考替代品(不在目錄中)
ADM6996A2T1 最大額定值與電氣特性
| Device Type | Ethernet switch controller |
| Ethernet Support | 10/100 Base-T/TX |
| Maximum Nominal Ethernet Rate | 100 Mbps |
| Host Interface | Parallel interface |
| Integrated Functions | Ethernet switch and Base-T/TX PHY |
| 封裝 | 128-BFQFP |
| 腳位數 | 128 pins |
| 安裝類型 | Surface mount |
| Media Interface | 10/100 Base-T/TX |
ADM6996A2T1 128-bfqfp 腳位配置指南
ADM6996A2T1(128-bfqfp 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: ADM6996A2T1.
請參閱 資料表 以查看完整腳位配置。
典型應用
ADM6996A2T1 適用於 6 應用s: Industrial Fast Ethernet Gateway, Embedded Router Control, FPGA-Based Network Interface, Factory Automation Terminal, Legacy Network Interface Card, Networked Sensor and Monitoring Hub.
Industrial Fast Ethernet Gateway
The ADM6996A2T1 fits an industrial Fast Ethernet gateway because it combines a 10/100 Base-T/TX switch controller and PHY function with a parallel host interface. A processor can use that parallel connection for packet transfer and control while the Infineon device handles the Ethernet-facing functions. The 128-BFQFP package provides the numerous mixed-signal and digital connections needed by this application. Before release, verify the exact port configuration, clock source, supported operating temperature, and isolation requirements for the industrial installation. The device is suitable for legacy 100 Mbps plant-network equipment, but it should not be assumed to support Gigabit Ethernet or modern automotive qualification without confirmation from the manufacturer documentation.
推薦
Embedded Router Control
The ADM6996A2T1 can provide the 10/100 Base-T/TX network front end for an embedded router whose main processor uses parallel data and control signals. Integrating the switch controller and PHY into one 128-BFQFP device reduces the need for separate Ethernet interface components. This arrangement is useful for compact networking equipment that requires 100 Mbps rather than gigabit throughput. The parallel interface must be matched carefully to the processor bus timing, and the PCB should provide continuous ground and well-controlled power distribution around the high-pin-count device. Because the controller configuration and electrical operating limits are defined by the manufacturer documentation, those tables should govern clock, reset, and power-supply implementation.
推薦
FPGA-Based Network Interface
The ADM6996A2T1 is suitable for an FPGA-based network interface when the FPGA implements packet processing, buffering, or protocol logic and the physical Ethernet front end is assigned to a dedicated controller. The device's parallel interface provides a direct digital path between the two devices, while its 10/100 Base-T/TX function supports standard Fast Ethernet links. Pin assignment, bus timing, clocking, and interrupt behavior must be verified against both the Infineon datasheet and the FPGA interface design. The 128-BFQFP package also requires careful escape routing because numerous high-speed and supply connections must leave the device without introducing excessive board area or signal discontinuity.
推薦
Factory Automation Terminal
The ADM6996A2T1 can support a factory automation terminal that connects a local controller to a 10/100 Base-T/TX network. Its integrated switch-controller and PHY functions provide the Ethernet-facing electronics, while the parallel interface permits integration with digital control logic without requiring a serial Ethernet interface. This is particularly relevant to legacy production equipment that remains limited to 100 Mbps. The implementation should include the interface and decoupling arrangements specified by the manufacturer and should verify environmental requirements at the product level rather than assuming that the IC alone satisfies isolation, surge, or enclosure requirements. EMC and thermal testing remain necessary at the completed equipment level.
推薦
Legacy Network Interface Card
The ADM6996A2T1 is applicable to a legacy 10/100 network interface card or embedded communication board that uses parallel logic rather than a compact serial network interface. The 128-BFQFP package exposes the required power, control, data, and Ethernet connections, allowing the controller and PHY functions to be placed on a multilayer PCB. Such designs are common when maintaining or reproducing equipment built around mature Fast Ethernet architectures. Before schematic capture, engineers must confirm the precise signal map, reference clock, reset requirements, and transceiver or magnetics interface from the manufacturer documentation. The board should also separate high-speed digital routing from sensitive Ethernet analog paths and maintain uninterrupted return paths beneath the device.
推薦
Networked Sensor and Monitoring Hub
The ADM6996A2T1 can form part of a networked monitoring hub that connects sensors or test channels through a 10/100 Base-T/TX link. A local processor can receive and process data through the parallel interface while the Infineon controller provides the Ethernet-facing switch and PHY functions. The architecture is appropriate where established 100 Mbps infrastructure is available but gigabit bandwidth is unnecessary. Designers should calculate timing margins for the parallel data path, follow the reference clock and reset requirements in the manufacturer datasheet, and preserve clean power and ground distribution around all 128 package contacts. Regulatory and environmental suitability for the final monitoring product must be established independently of the component-level feature set.
推薦
推薦產品摘要
工程參考資料,適用於 ADM6996A2T1 — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | ADM6996HX-AD-T-1 | ADM6996FCX-AC-T-1 | ADM6996LCX-AD-R-1 | ADM6992X-AD-T-1 |
|---|---|---|---|---|---|
| Package | 128-BFQFP | 128-BFQFP | 128-BFQFP | 128-BFQFP | 128-BFQFP |
| Brand | Infineon | Infineon | Infineon | Infineon | Infineon |
| Product Series | ADM6996 | ADM6996 | ADM6996 | ADM6996 | ADM6992 |
| Function | Ethernet switch controller with Base-T/TX PHY | Ethernet switch controller | Ethernet switch component | Ethernet switch with Base-T/TX PHY | Fiber-to-Fast-Ethernet converter |
| Ethernet Rate | 10/100 Base-T/TX | 10/100 Base-T/TX | 10/100 Base-T/TX | 10/100 Base-T/TX | Fast Ethernet |
| Host Interface | Parallel | Parallel | Parallel | Parallel | Parallel |
| Protocol | Ethernet | Ethernet | Ethernet | Ethernet | Ethernet |
主要差異化特點
- Closest documented same-package substitute (對比ADM6996HX-AD-T-1)
- Direct switch-controller configuration (對比ADM6992X-AD-T-1)
- Current listing versus legacy catalog entries (對比ADM6996LCX-AD-R-1)
設計說明
Create the 128-BFQFP footprint directly from the manufacturer package drawing and cross-check pin 1, lead pitch, body dimensions, and exposed-pad requirements. Keep the parallel data and control routes short and route them over a continuous ground plane. Because the device combines digital and analog Ethernet functions, separate high-speed digital traffic from sensitive Ethernet signal paths rather than relying only on component placement.
Implement the supply rails, decoupling network, and power sequencing exactly as shown in the manufacturer application information. Place the required high-frequency decoupling capacitors at the associated power pins and provide a low-impedance return path for each connection. Do not infer the operating voltage range from the Ethernet rating; confirm supply limits, absolute-maximum ratings, and power-up behavior in the manufacturer datasheet.
Treat the parallel host interface as a timed bus. Match trace lengths where the interface timing specification requires it, avoid stubs, and use appropriate series termination if recommended by the interface guidance. Route clock and data as a coordinated group, minimize right-angle turns, and provide continuous reference planes. Validate the completed layout with the specified clock, load, and interface timing conditions.
Do not treat a shared package name as proof of complete interchangeability. Before replacing ADM6996A2T1, compare pin names, supply levels, clock requirements, reset behavior, register or control compatibility, media interfaces, and lifecycle status for the exact alternative ordering code. In particular, ADM6996HX-AD-T-1 is reported as equivalent in primary parameters, while ADM6992X-AD-T-1 is identified as a fiber-to-Fast-Ethernet converter and may require different external support circuitry.
合規資訊
No definitive RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations were established for this exact MPN. Confirm the applicable declarations with the manufacturer before procurement or production release.