ADS7804PB - 12-Bit 100 kSPS SAR ADC | Texas Instruments
MPN: ADS7804PB ✓ 啟用中ADS7804PB 概覽
An ADC is an interface component that converts a continuously varying analog voltage into a numeric value for processing, measurement, or control. The ADS7804PB belongs to the SAR ADC family, where a comparator and internal capacitor array determine the digital result one bit at a time. This architecture is appropriate for low-to-medium sampling rates and typically provides predictable conversion timing, straightforward digital control, and good suitability for industrial measurement systems.
The ADS7804PB offers 12-bit resolution, a 0.1 MHz sample rate, and 0.011% endpoint error according to the manufacturer-related technical listing. Its 2's complement binary output format allows direct connection to suitable microprocessor or digital bus circuitry. The operating voltage is 5 V, while the specified operating temperature range is -40 °C to +85 °C. The parallel output architecture requires the host processor to capture the digital result and can require careful bus timing analysis when the converter is used with high-speed peripherals.
The device includes an internal reference and clock, reducing the number of external timing and reference components required in a basic circuit. It also includes three-state output drivers, allowing multiple devices to share parallel bus lines when the system design uses appropriate addressing and enable control. Offset and full-scale calibration procedures are described in the manufacturer datasheet, including fixed-resistor test conditions and internal adjustment methods.
Typical applications include industrial process monitoring, instrumentation, data acquisition, embedded measurement systems, and digital control panels. The 100 kSPS sampling rate is useful for signals requiring regular periodic sampling rather than high-frequency waveform capture. The 28-pin PDIP package favors through-hole construction and prototype or legacy industrial boards where a surface-mount land pattern is not required.
Designers should verify the analog input range, reference accuracy, acquisition timing, output enable behavior, and digital interface timing against the manufacturer datasheet before placing the converter in a new design. Decoupling should follow the datasheet recommendations, and the analog input should be routed away from high-current switching nodes. This page combines the available manufacturer specifications, package information, application guidance, and replacement considerations for engineering selection.
直接替換替代品,適用於 ADS7804PB — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: ADS7804PB (相同外形與佔位) — 差異在於 Architecture, Package, Sampling Rate, Supply Voltage.
ADS7804UB
✅ 直接替換📋 參考替代品(不在目錄中)
ADS8504IBDW
✅ 直接替換📋 參考替代品(不在目錄中)
ADS7804PB 最大額定值與電氣特性
| 解析度 | 12 bits |
| 取樣率 | 100 kSPS |
| Conversion Time | 8 us |
| 供應電壓 | 5 V |
| Input Channel Count | 1 channel |
| Architecture | Successive-approximation SAR |
| Output Format | 2's complement binary |
| Output Interface | Parallel microprocessor-compatible interface |
| 工作溫度範圍 | -40 °C to +85 °C |
| Endpoint Error | 0.011% |
| 封裝 | 28-pin PDIP |
| 安裝類型 | Through-hole |
| Number of Terminals | 28 |
| Integrated Reference | Yes |
| Integrated Clock | Yes |
| Sample-and-Hold Circuit | Integrated |
| Output Driver Type | Three-state output drivers |
| Temperature Grade | Industrial |
| Technology | CMOS |
ADS7804PB 28-pin pdip 腳位配置指南
ADS7804PB(28-pin pdip 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: ADS7804PB.
請參閱 資料表 以查看完整腳位配置。
典型應用
ADS7804PB 適用於 6 應用s: Industrial Process Monitoring, Data Acquisition Systems, Digital Panel Meters, Embedded Control and Instrumentation, Test and Measurement Equipment, Power and Battery Monitoring.
Industrial Process Monitoring
The ADS7804PB fits industrial process-monitoring systems that periodically measure a single analog pressure, temperature, or level signal. Its 12-bit resolution provides 4,096 digital codes, while the 100 kSPS sampling rate is more than adequate for many slow-changing process variables. Place the converter behind the appropriate sensor-conditioning network, use the manufacturer-specified reference and decoupling arrangement, and route the parallel output to a host processor or bus interface. The 28-pin PDIP package also simplifies assembly on through-hole industrial controller boards. Designers should confirm the allowable analog input range, acquisition interval, and calibration method in the Texas Instruments ADS7804 datasheet before finalizing the signal chain.
推薦
Data Acquisition Systems
The ADS7804PB is suitable for moderate-speed data-acquisition front ends that digitize one analog channel for storage or real-time analysis. At 12 bits and 100 kSPS, it provides a practical balance between measurement resolution, conversion speed, and interface simplicity. The capacitor-based SAR conversion uses an integrated sample-and-hold stage, while the internal reference and clock reduce external component count. For a complete acquisition card, decouple the 5 V supply as specified, isolate the analog input from digital switching paths, and implement the host handshake around the three-state parallel outputs. If the system needs simultaneous channels, higher resolution, or a serial interface, use a different converter architecture rather than expanding beyond the ADS7804PB's single-channel design.
推薦
Digital Panel Meters
The ADS7804PB can serve as the analog measurement element in a digital panel meter for industrial displays. A 12-bit converter is appropriate when the instrument must show a stable numerical value rather than capture a fast transient, and the 100 kSPS rate allows frequent refresh with averaging or filtering. The microprocessor-compatible parallel interface can feed a controller that performs scaling, calibration, and display formatting. Keep sensitive analog traces away from display-driver and switching-supply nodes, provide the recommended reference and bypass capacitors, and account for the ADC input acquisition interval in the measurement timing. The through-hole PDIP format is especially convenient for panel-meter boards assembled with conventional through-hole components.
推薦
Embedded Control and Instrumentation
The ADS7804PB fits embedded instrumentation that periodically evaluates an analog feedback signal for a control loop. Its 8 microsecond conversion time and 100 kSPS maximum sampling rate support timely updates, while 12-bit resolution can represent control variables with adequate granularity. The parallel output supports direct connection to suitable microprocessor input circuitry, and three-state drivers permit controlled bus sharing where the system architecture supports it. In a control application, define the complete signal scaling, offset, and gain-calibration procedure, and use software filtering or hardware averaging when the measured signal contains noise. Check the analog input range and operating temperature limits against the manufacturer datasheet before assigning the converter to safety-critical or precision control functions.
推薦
Test and Measurement Equipment
The ADS7804PB is appropriate for compact test and measurement equipment that converts a calibrated input into a digital result. Its 12-bit resolution, industrial temperature range, and single-sample SAR operation make it suitable for bench instruments and production test fixtures that do not require simultaneous sampling. The internal reference and clock support a straightforward analog front end, while the parallel output can feed a controller for calibration, limits checking, and result logging. Use the datasheet's offset and full-scale calibration procedure with the specified fixed resistors to establish repeatable measurements. Protect the analog input from external transients, maintain the specified supply bypassing, and verify the exact acquisition timing when testing rapidly changing signals.
推薦
Power and Battery Monitoring
The ADS7804PB can digitize a scaled voltage from a power supply, battery pack, or energy-storage system when the application requires a basic measurement of one analog rail. The 5 V supply operation is convenient for conventional control electronics, and the 100 kSPS rate can capture current and voltage trends during load transitions. Place the converter on the measurement side of the power system with input filtering, limiting, and scaling designed for its absolute input range. The three-state parallel outputs allow bus sharing where the host design includes appropriate output-enable control. This use should not replace a dedicated battery-management IC when accurate coulomb counting, protection, or cell balancing is required; the ADS7804PB is best used for supervisory measurement and diagnostics.
推薦
推薦產品摘要
工程參考資料,適用於 ADS7804PB — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | ADS7804UB | ADS8504IBDW |
|---|---|---|---|
| Package | 28-pin PDIP | 28-pin PDIP comparison candidate | 28-pin PDIP comparison candidate |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Resolution | 12 bits | 12 bits | 12 bits |
| Input Channel Count | 1 channel | 1 channel family rating | 1 channel |
| Operating Temperature Range | -40 °C to +85 °C | -40 °C to +85 °C family rating | -40 °C to +85 °C |
| Output Interface | Parallel microprocessor-compatible output | Parallel family interface | Parallel microprocessor interface |
主要差異化特點
- Matches a through-hole single-channel measurement architecture (對比ADS8504IBDW)
- Uses the same 12-bit, 100 kSPS ADS7804 family performance target (對比ADS7804UB)
- Combines an internal reference, clock, and sample-and-hold circuit (對比ADS8504IBDW)
設計說明
Follow the manufacturer datasheet for input, reference, and supply bypass-capacitor placement, and place each capacitor directly beside its associated device pin. Keep the analog input trace short and physically separated from digital output and switching-supply paths. The ADS7804PB uses a 28-pin PDIP footprint, so verify the hole pattern and pin-1 orientation on the PCB rather than assuming compatibility with a SOIC package.
Allow the full sample-and-hold acquisition interval and the specified 8 microsecond conversion time when defining the timing between input settling and digital readback. Account for the host bus setup and hold requirements of the 12-bit parallel outputs, and control the three-state output enable so adjacent devices do not contend on shared bus lines. Add digital filtering only after confirming that filtering delay is acceptable for the control loop.
Do not assume that a converter with the same base family name is automatically a drop-in substitute. Confirm the suffix-specific package, pin assignment, electrical limits, reference arrangement, output coding, and temperature grade against the manufacturer datasheet. For ADS7804UB and ADS8504IBDW, verify the complete pin list and timing behavior before revising an existing PCB.
Use the documented offset and full-scale calibration method, including the specified fixed resistors, when calibrating the measurement path. Endpoint error and resolution alone do not establish the complete accuracy of the external analog front end. Sensor excitation, reference drift, analog filtering, grounding, and PCB leakage can dominate the final measurement result and should be evaluated as part of system calibration.
合規資訊
No specific environmental or material-compliance declarations for ADS7804PB are identified in the available manufacturer and distributor records. The industrial temperature specification does not by itself establish AEC-Q100 qualification.