ADS7831P - 12-Bit 600 kSPS Parallel ADC | Texas Instruments
MPN: ADS7831P ✓ 啟用中ADS7831P 概覽
An ADC is a data-converter IC that transforms a continuously varying analog voltage into a digital numerical value. The ADS7831P belongs to the parallel-output ADC family, where each conversion produces a 12-bit code through 12 output lines. Compared with a serial-output ADC, the parallel interface can reduce the number of clock cycles required to transfer each sample. This makes it useful when the receiving controller, FPGA, or data-acquisition system benefits from short deterministic acquisition cycles.
The principal performance characteristics include a 600 kHz throughput rate, 12-bit resolution, 69 dB minimum SINAD with a 250 kHz input, and a specified 15 MHz −3 dB input bandwidth. The analog input is presented through a bipolar ±2.5 V range, while the digital output uses 2's-complement binary coding. A typical conversion produces one code for every 4096 input levels, although actual accuracy is also affected by offset, gain, integral nonlinearity, differential nonlinearity, noise, and reference behavior.
The ADS7831P is a complete sampling ADC rather than a bare switched-capacitor core. Its sample-and-hold amplifier captures the input during the acquisition interval, and its internal successive-approximation circuitry determines the digital code. The parallel outputs are latched, allowing the external system to capture the result through an appropriate clocking arrangement. Supply and reference decoupling, input-source settling, clock quality, and output timing remain the principal determinants of usable system performance.
Typical uses include multichannel measurement systems, process-control instrumentation, laboratory data acquisition, industrial sensor interfaces, and feedback loops that require deterministic sampling. The 600 kSPS rate is sufficient for many industrial analog signals, while the ±2.5 V input range simplifies interfacing with bipolar sensor stages. Systems operating at different common-mode or input ranges can add suitable front-end attenuation, amplification, level shifting, or protection.
PCB design should keep the analog input, reference, and clock paths short and separated from digital output routing. Place power and reference capacitors close to their associated pins, use a stable low-noise reference arrangement, and observe the datasheet timing requirements for acquisition and conversion. Analog and digital return currents should be managed carefully so switching currents do not add noise directly into the sensitive input node.
This page organizes the ADS7831P specifications, qualified drop-in considerations, application guidance, and design notes into an engineering-focused reference. It also identifies specification fields that require confirmation from the manufacturer datasheet before a schematic or production BOM is released.
直接替換替代品,適用於 ADS7831P — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
ADS7831IPU
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
ADS7831P 最大額定值與電氣特性
| Converter Type | Successive-approximation ADC |
| 解析度 | 12 bit |
| Number of Channels | 1 channel |
| 取樣率 | 600 kSPS |
| Throughput Rate | 600 kHz |
| Input Range | ±2.5 V |
| 供應電壓 | ±5 V |
| Signal-to-Noise and Distortion | 69 dB minimum at 250 kHz input |
| Linearity Error | 0.0244% |
| Input Bandwidth | 15 MHz at −3 dB |
| Output Format | 2's-complement binary |
| 介面 | 12-bit parallel output |
| Sample-and-Hold | Integrated |
| Reference | Internal |
| Technology | CMOS |
| 工作溫度範圍 | −40 °C to +85 °C |
| 封裝 | 28-pin PDIP, 0.3 inch pitch |
| Package Type | Through-hole PDIP |
| 安裝類型 | Through-hole |
ADS7831P through-hole pdip 腳位配置指南
ADS7831P(through-hole pdip 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: ADS7831P.
請參閱 資料表 以查看完整腳位配置。
典型應用
ADS7831P 適用於 6 應用s: Industrial Process Measurement, Laboratory Data Acquisition, Precision Feedback Control, Sensor Signal Acquisition, Power and Drive Monitoring, Communication Interface Conditioning.
Industrial Process Measurement
The ADS7831P fits industrial process-measurement loops that require a bipolar sensor signal, 12-bit resolution, and a 600 kSPS conversion rate. Its ±2.5 V input range can represent pressure, temperature, and position signals after suitable conditioning, while the parallel output reduces the number of clock cycles needed to transfer each code. Place the converter close to the front end, reference bypass network, and isolation interface to reduce susceptibility to switching noise. The principal system trade-off is the 28-pin through-hole footprint, which uses more board space than a compact serial-output ADC.
推薦
Laboratory Data Acquisition
For laboratory instrumentation, the ADS7831P provides a deterministic 12-bit code at up to 600 kSPS and exposes the result through a parallel interface suitable for capture logic or an FPGA. Its 15 MHz −3 dB input bandwidth supports measurements whose source bandwidth is well below the conversion rate, while the 69 dB minimum SINAD specification applies under the stated 250 kHz input condition. Accurate results depend on low-noise reference layout, controlled clock timing, adequate acquisition settling, and shielding or guarding of high-impedance sensor inputs.
推薦
Precision Feedback Control
The ADS7831P can close a deterministic feedback loop when controller logic benefits from receiving all 12 conversion bits simultaneously. A 600 kSPS acquisition rate provides useful temporal resolution for position, actuator, and analog process-control signals, although total loop latency must include the front end, acquisition interval, conversion cycle, output capture, and controller update. The ±2.5 V input range supports bipolar control signals. Use a stable reference, separate analog and digital return paths, and an input filter selected for both noise rejection and required loop bandwidth.
推薦
Sensor Signal Acquisition
The ADS7831P is appropriate for sensor interfaces whose conditioned output falls within ±2.5 V and requires 12-bit digital resolution. Its integrated sample-and-hold circuit captures the input, and the parallel output transfers the resulting code without a serial shift cycle. A bipolar front end can map sensor outputs around zero, while the 69 dB minimum SINAD and 0.0244% linearity specification define important performance limits at the stated test condition. Verify source settling during the acquisition interval and protect the input against overvoltage, ESD, and industrial transients.
推薦
Power and Drive Monitoring
The ADS7831P can monitor bipolar feedback or drive signals in power-conversion equipment where a fast, deterministic measurement is needed. Its 600 kSPS rate can capture changes across many control cycles, and the 15 MHz −3 dB analog bandwidth can accommodate substantially faster signals than the conversion rate. The converter is not itself a replacement for a precision power measurement front end, so scaling, level shifting, filtering, and isolation must be designed separately. Keep high-current switching nodes away from the analog input and reference routing.
推薦
Communication Interface Conditioning
The ADS7831P can provide the analog-to-digital conversion stage for communication equipment that samples a bipolar baseband signal and transfers the code to parallel logic. The 12-bit parallel output can interface directly with appropriately timed CPLD or FPGA capture resources, while the 600 kSPS rate supports many moderate-bandwidth modulation or supervisory waveforms. Input bandwidth, acquisition settling, clock jitter, and reference stability must be evaluated together. The 28-pin PDIP footprint and 12 data lines make it more board-intensive than a multiplexed serial converter.
推薦
推薦產品摘要
工程參考資料,適用於 ADS7831P — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | ADS7831IPU |
|---|---|---|
| Package | 28-pin PDIP | 28-pin PDIP |
| Brand | Texas Instruments | Texas Instruments |
| Resolution | 12 bit | 12 bit |
| Number of Channels | 1 channel | 1 channel |
| Sampling Rate | 600 kSPS | 600 kSPS |
| Input Range | ±2.5 V | ±2.5 V |
| Supply Voltage | ±5 V | ±5 V |
| SINAD | 69 dB minimum at 250 kHz input | 69 dB minimum at 250 kHz input |
| Input Bandwidth | 15 MHz at −3 dB | 15 MHz at −3 dB |
| Output Interface | 12-bit parallel, 2's-complement binary | 12-bit parallel, 2's-complement binary |
主要差異化特點
- Deterministic parallel conversion interface (對比ADS7831IPU)
- Single-cycle conversion rate suited to deterministic acquisition (對比ADS7831IPU)
- Integrated complete conversion front end (對比ADS7831IPU)
設計說明
Route the analog input directly to the converter and keep the surrounding front end away from clock and parallel-output nets. Place input, supply, and reference capacitors at the pins specified in the manufacturer datasheet. Use a continuous ground reference under the device where the package and board construction permit, and return analog and digital currents through controlled paths so switching-node energy does not share a narrow trace with the input or reference node.
Do not treat the 600 kSPS conversion rate as permission to place an arbitrary source directly on the input. Confirm that the source impedance, acquisition time, and output impedance satisfy the settling requirements for 12-bit accuracy. Also verify the distinction between the 15 MHz analog bandwidth and the 600 kSPS sampling rate. An input filter must preserve required signal bandwidth while limiting out-of-band noise.
Provide the specified ±5 V supplies with separate, low-impedance decoupling at the power pins and observe all common-mode and sequencing limits in the manufacturer datasheet. Reference and supply disturbances can appear directly as gain or offset errors, especially when converting small bipolar signals. Check the reference startup behavior, bypass network, and power-supply rejection over the operating frequency range rather than relying only on the nominal conversion rate.
Use a controlled clock source and route clock traces away from the analog input and reference nodes. The parallel outputs are edge-driven signals, so their settling must be included in the receiver timing budget. Match receiver thresholds and trace loading appropriately, use termination only when required by the actual edge rate, and avoid long stubs between the converter and capture logic. The 28 output connections also require adequate grounding and decoupling around the receiving device.
合規資訊
The operating temperature range indicates a commercial or industrial-temperature application rather than an automotive-qualified product. Confirm current environmental-material declarations from the manufacturer product documentation before procurement.