Texas Instruments

ADS7831P - 12-Bit 600 kSPS Parallel ADC | Texas Instruments

부품 번호: ADS7831P ✓ 활성
±5 V Vdss 28-pin PDIP, 0.3 inch pitch Package
MOQ: 1 |

ADS7831P 개요

Texas Instruments ADS7831P is a 12-bit, single-channel CMOS successive-approximation analog-to-digital converter with a 600 kSPS sampling rate, parallel data output, and a 28-pin PDIP package. It accepts a standard ±2.5 V analog input range and operates from ±5 V power supplies, making it suitable for instrumentation, industrial data acquisition, and precision signal-measurement systems. The converter uses a fully differential internal architecture with an integrated sample-and-hold circuit, reference circuitry, clock input, and parallel output latches.

An ADC is a data-converter IC that transforms a continuously varying analog voltage into a digital numerical value. The ADS7831P belongs to the parallel-output ADC family, where each conversion produces a 12-bit code through 12 output lines. Compared with a serial-output ADC, the parallel interface can reduce the number of clock cycles required to transfer each sample. This makes it useful when the receiving controller, FPGA, or data-acquisition system benefits from short deterministic acquisition cycles.

The principal performance characteristics include a 600 kHz throughput rate, 12-bit resolution, 69 dB minimum SINAD with a 250 kHz input, and a specified 15 MHz −3 dB input bandwidth. The analog input is presented through a bipolar ±2.5 V range, while the digital output uses 2's-complement binary coding. A typical conversion produces one code for every 4096 input levels, although actual accuracy is also affected by offset, gain, integral nonlinearity, differential nonlinearity, noise, and reference behavior.

The ADS7831P is a complete sampling ADC rather than a bare switched-capacitor core. Its sample-and-hold amplifier captures the input during the acquisition interval, and its internal successive-approximation circuitry determines the digital code. The parallel outputs are latched, allowing the external system to capture the result through an appropriate clocking arrangement. Supply and reference decoupling, input-source settling, clock quality, and output timing remain the principal determinants of usable system performance.

Typical uses include multichannel measurement systems, process-control instrumentation, laboratory data acquisition, industrial sensor interfaces, and feedback loops that require deterministic sampling. The 600 kSPS rate is sufficient for many industrial analog signals, while the ±2.5 V input range simplifies interfacing with bipolar sensor stages. Systems operating at different common-mode or input ranges can add suitable front-end attenuation, amplification, level shifting, or protection.

PCB design should keep the analog input, reference, and clock paths short and separated from digital output routing. Place power and reference capacitors close to their associated pins, use a stable low-noise reference arrangement, and observe the datasheet timing requirements for acquisition and conversion. Analog and digital return currents should be managed carefully so switching currents do not add noise directly into the sensitive input node.

This page organizes the ADS7831P specifications, qualified drop-in considerations, application guidance, and design notes into an engineering-focused reference. It also identifies specification fields that require confirmation from the manufacturer datasheet before a schematic or production BOM is released.

드롭인 대체품: ADS7831P — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.

ADS7831IPU

✅ 드롭인 ⚠️ 사양 미검증
📦 28-pin PDIP
Temperature-grade and ordering suffix may differ; verify the exact pin assignments and electrical limits before substitution

📋 참조 대체품 (카탈로그에 없음)

ADS7831P 최대 정격 & 전기적 특성

Converter Type Successive-approximation ADC
분해능 12 bit
Number of Channels 1 channel
샘플링 속도 600 kSPS
Throughput Rate 600 kHz
Input Range ±2.5 V
공급 전압 ±5 V
Signal-to-Noise and Distortion 69 dB minimum at 250 kHz input
Linearity Error 0.0244%
Input Bandwidth 15 MHz at −3 dB
Output Format 2's-complement binary
인터페이스 12-bit parallel output
Sample-and-Hold Integrated
Reference Internal
Technology CMOS
동작 온도 범위 −40 °C to +85 °C
패키지 28-pin PDIP, 0.3 inch pitch
Package Type Through-hole PDIP
실장 유형 Through-hole

ADS7831P through-hole pdip 핀 구성 가이드

ADS7831P(through-hole pdip 패키지)의 핀 구성입니다. 이 아날로그 부품에는 입력, 출력, 전원 공급 핀이 있습니다. 오프셋 널, 보상, 인에이블 핀 구성은 제조사 데이터시트를 참조하십시오. 신호 컨디셔닝 및 증폭기 회로에 이상적입니다.

ADS7831P의 through-hole pdip 패키지 핀아웃 다이어그램

다음에 대한 상세 핀아웃 데이터 없음: ADS7831P.

다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.

일반적인 애플리케이션

ADS7831P 적합 용도: 6 애플리케이션s: Industrial Process Measurement, Laboratory Data Acquisition, Precision Feedback Control, Sensor Signal Acquisition, Power and Drive Monitoring, Communication Interface Conditioning.

🏭

Industrial Process Measurement

The ADS7831P fits industrial process-measurement loops that require a bipolar sensor signal, 12-bit resolution, and a 600 kSPS conversion rate. Its ±2.5 V input range can represent pressure, temperature, and position signals after suitable conditioning, while the parallel output reduces the number of clock cycles needed to transfer each code. Place the converter close to the front end, reference bypass network, and isolation interface to reduce susceptibility to switching noise. The principal system trade-off is the 28-pin through-hole footprint, which uses more board space than a compact serial-output ADC.

🖥️

Laboratory Data Acquisition

For laboratory instrumentation, the ADS7831P provides a deterministic 12-bit code at up to 600 kSPS and exposes the result through a parallel interface suitable for capture logic or an FPGA. Its 15 MHz −3 dB input bandwidth supports measurements whose source bandwidth is well below the conversion rate, while the 69 dB minimum SINAD specification applies under the stated 250 kHz input condition. Accurate results depend on low-noise reference layout, controlled clock timing, adequate acquisition settling, and shielding or guarding of high-impedance sensor inputs.

🔧

Precision Feedback Control

The ADS7831P can close a deterministic feedback loop when controller logic benefits from receiving all 12 conversion bits simultaneously. A 600 kSPS acquisition rate provides useful temporal resolution for position, actuator, and analog process-control signals, although total loop latency must include the front end, acquisition interval, conversion cycle, output capture, and controller update. The ±2.5 V input range supports bipolar control signals. Use a stable reference, separate analog and digital return paths, and an input filter selected for both noise rejection and required loop bandwidth.

🧩

Sensor Signal Acquisition

The ADS7831P is appropriate for sensor interfaces whose conditioned output falls within ±2.5 V and requires 12-bit digital resolution. Its integrated sample-and-hold circuit captures the input, and the parallel output transfers the resulting code without a serial shift cycle. A bipolar front end can map sensor outputs around zero, while the 69 dB minimum SINAD and 0.0244% linearity specification define important performance limits at the stated test condition. Verify source settling during the acquisition interval and protect the input against overvoltage, ESD, and industrial transients.

⚡

Power and Drive Monitoring

The ADS7831P can monitor bipolar feedback or drive signals in power-conversion equipment where a fast, deterministic measurement is needed. Its 600 kSPS rate can capture changes across many control cycles, and the 15 MHz −3 dB analog bandwidth can accommodate substantially faster signals than the conversion rate. The converter is not itself a replacement for a precision power measurement front end, so scaling, level shifting, filtering, and isolation must be designed separately. Keep high-current switching nodes away from the analog input and reference routing.

🌐

Communication Interface Conditioning

The ADS7831P can provide the analog-to-digital conversion stage for communication equipment that samples a bipolar baseband signal and transfers the code to parallel logic. The 12-bit parallel output can interface directly with appropriately timed CPLD or FPGA capture resources, while the 600 kSPS rate supports many moderate-bandwidth modulation or supervisory waveforms. Input bandwidth, acquisition settling, clock jitter, and reference stability must be evaluated together. The 28-pin PDIP footprint and 12 data lines make it more board-intensive than a multiplexed serial converter.

What is the ADS7831P?
The ADS7831P is a Texas Instruments 12-bit, single-channel CMOS ADC with a 600 kSPS sampling rate, parallel output interface, and 28-pin PDIP package. According to the manufacturer ADS7831 datasheet, it includes a sample-and-hold circuit, internal reference, clock input, and parallel output latches. Its standard bipolar analog input range is ±2.5 V, while the specified operating supply is ±5 V. The device is intended for data-acquisition, instrumentation, process-control, and other applications requiring deterministic sampling without a serial interface.
What is the conversion rate of the ADS7831P?
The ADS7831P has a maximum sampling throughput of 600 kSPS, equivalent to 600 kHz conversions per second. According to the manufacturer ADS7831 datasheet, each result is represented as a 12-bit parallel code, and the converter uses a successive-approximation architecture with an integrated sample-and-hold circuit. Actual acquisition rates in an instrument can be lower when the source impedance, acquisition timing, conversion control, or digital data-capture cycle requires additional settling time.
What is the analog input range of the ADS7831P?
The ADS7831P accepts a standard bipolar input range of ±2.5 V. According to the manufacturer ADS7831 datasheet, its input circuitry also supports a specified 15 MHz −3 dB bandwidth. This bandwidth describes the frequency response of the analog path rather than the maximum conversion rate. For sensors or circuits outside the ±2.5 V range, use suitable attenuation, amplification, or level-shaping circuits, and verify settling behavior across the complete input bandwidth required by the application.
What are the key specifications of ADS7831P that engineers should know?
The ADS7831P combines 12-bit resolution, one analog input channel, a 600 kSPS sampling rate, and a parallel 2's-complement output interface. According to the manufacturer ADS7831 datasheet, it provides a 69 dB minimum SINAD for a 250 kHz input, 0.0244% linearity error, ±5 V operation, and a 15 MHz −3 dB input bandwidth. The device is packaged in a 28-pin PDIP and includes the sample-and-hold, reference, and clock functions needed for a complete converter.
Where can I download the ADS7831P datasheet PDF?
The ADS7831P datasheet PDF is available through the manufacturer product documentation linked from the Texas Instruments ADS7831 family page. The PDF contains the authoritative pin descriptions, acquisition and conversion timing, electrical characteristics, reference requirements, and application information. Use the pin-description table and timing diagrams when assigning PCB nets and designing the external clock, input, reference, and parallel-output interfaces.
Where can I find the ADS7831P pinout?
The ADS7831P pinout is defined by the 28-pin PDIP pin-description table in the manufacturer ADS7831 datasheet. The package uses 0.3 inch pitch through-hole pins, and the pin numbering starts at pin 1 according to the package orientation marking. Use that table to identify analog inputs, power connections, reference terminals, control signals, clock inputs, and the 12 parallel output bits before finalizing a schematic or PCB netlist.
How does the ADS7831P compare with a serial-output ADC?
The ADS7831P transfers each 12-bit result over parallel outputs, whereas a serial ADC normally shifts the same code across one or more serial lines. The parallel interface can reduce transfer time and simplify capture into parallel-capable logic or FPGA logic. Its trade-off is a higher pin count and more PCB routing than a serial ADC. According to the manufacturer ADS7831 datasheet, the device also offers a 600 kSPS sampling rate and a 15 MHz −3 dB analog input bandwidth.
What power supplies does the ADS7831P require?
The ADS7831P operates from ±5 V supplies for its specified analog operating conditions. According to the manufacturer ADS7831 datasheet, the converter accepts a bipolar ±2.5 V signal range and uses an internal reference. Decoupling requirements must be followed because reference and supply noise can directly affect conversion accuracy. Confirm capacitor values, voltage tolerances, and sequencing requirements from the electrical-characteristics and application sections before releasing the power design.
Can the ADS7831P be used for industrial data acquisition?
Yes, the ADS7831P is suitable for industrial data-acquisition systems that need bipolar signals, deterministic sampling, and parallel digital output. Its 12-bit resolution, 600 kSPS rate, −40 °C to +85 °C operating range, and integrated sample-and-hold, reference, and clock functions support measurement systems. For factory equipment, isolate field wiring appropriately, protect inputs from transients, and verify that the selected front-end and ADC grounding arrangement meet required noise and safety objectives.
Is ADS7831P suitable for process-control feedback loops?
Yes, ADS7831P is suitable for process-control and feedback applications requiring a deterministic 600 kSPS sampling capability. The 12-bit code can represent the measured bipolar input, while the parallel interface allows efficient acquisition by a controller. Control-loop performance still depends on total latency, sensor response, input filtering, isolation, and the time required to acquire and transfer each conversion. Include those delays in loop analysis rather than relying on the sampling rate alone.
What can replace the ADS7831P?
The closest same-family replacement is the ADS7831IPU, which is listed from LLM knowledge as a Texas Instruments 28-pin PDIP variant in the ADS7831 family. Its replacement status should be confirmed by comparing the exact pin table, electrical limits, timing, and temperature grade in the manufacturer datasheets. The cross-reference search did not identify additional verified pin-compatible components, so unverified functional equivalents should not be treated as drop-in replacements.
Is ADS7831IPU a drop-in replacement for ADS7831P?
ADS7831IPU is the only candidate identified as a potentially compatible same-family replacement, and it must be treated as conditional until its package and pin assignments are checked. It is listed with LLM knowledge because the cross-reference results did not name a specific alternative. According to the target listing, ADS7831P uses a 28-pin PDIP; verify that ADS7831IPU uses the identical 28-pin footprint and that supply, reference, timing, output-code, and temperature specifications satisfy the original design.
What is the best Analog Devices equivalent for ADS7831P?
No verified Analog Devices equivalent was identified for ADS7831P in the available cross-reference results. A functional ADC with a 12-bit resolution and comparable sampling rate is not automatically a drop-in replacement because the ADS7831P uses a 28-pin parallel interface and a specific bipolar input and reference arrangement. Any proposed substitute must be checked for identical pin assignments, logic levels, acquisition timing, reference behavior, and package dimensions before it can replace the original device.
ADS7831P versus ADS7831IPU — which should be selected?
ADS7831P is the specified original 12-bit, 600 kSPS parallel ADC in a 28-pin PDIP, while ADS7831IPU is a potentially compatible member of the same family. The choice should be based on verified pin compatibility, operating-temperature grade, electrical limits, and orderable status rather than the suffix alone. According to the manufacturer family documentation, both belong to the ADS7831 conversion family; confirm the exact variant limits and lifecycle status before substitution.
When should I choose ADS7831P instead of a serial-output ADC?
Choose ADS7831P when the design benefits from a 12-bit parallel interface, a 600 kSPS sampling rate, and immediate access to all result bits through separate output lines. It is especially useful when the FPGA, latch, or acquisition logic can capture parallel data without a serial clock and shift-register cycle. A serial ADC remains preferable when board space, pin count, cable routing, or system power budget dominates. The parallel interface requires careful output timing and more PCB routing.
Where to buy ADS7831P online?
Use the Request a Quote form on this page to request current ADS7831P availability, commercial terms, and the appropriate 28-pin PDIP configuration. The form is the correct channel for a quote because pricing, stock, lead time, and manufacturer-specific order codes can change. Before requesting a shipment, identify the required temperature grade, quantity, and any RoHS or traceability documentation your production process requires.
What is the price of ADS7831P?
Request current ADS7831P pricing through the Request a Quote form on this page. The quote can be matched to the exact 28-pin PDIP package and required quantity, avoiding ambiguity with other ADS7831 package or temperature options. Pricing shown by marketplace listings may change without notice, so use the quotation response for purchasing approval and planning rather than relying on a static figure.
What is the lead time for ADS7831P?
Request the current ADS7831P lead time and minimum order quantity through the Request a Quote form on this page. Lead time can depend on the exact package suffix, production schedule, order quantity, and shipment destination. The current product listing confirms an orderable ADS7831P configuration, but it does not state a fixed lead time. Include the target date and annual usage in the request for useful scheduling information.
Is ADS7831P in stock?
Current ADS7831P stock status should be confirmed through the Request a Quote form on this page. Because availability can vary by package suffix, quantity, and manufacturing schedule, use the quotation response for procurement decisions. The product listing identifies ADS7831P as a 28-pin PDIP ADC configuration, and the form allows the request to include the desired quantity and required delivery schedule.

엔지니어링 참조 데이터: ADS7831P — 비교, 설계 지침 및 규정 준수 정보.

선택 가이드

Choose ADS7831P when the design requires a single bipolar input, 12-bit resolution, a 600 kSPS conversion rate, and direct parallel capture. It is particularly suitable where deterministic acquisition and short data-transfer intervals matter more than minimizing pin count or board area. ADS7831IPU is the only potentially compatible same-family candidate identified, and it should be selected only after confirming its exact temperature grade, ordering status, pin assignments, and electrical limits against the original design. No verified cross-brand drop-in alternative was identified, so other 12-bit ADCs should be treated as redesign candidates rather than replacements. A serial-output ADC is preferable when PCB area, pin count, and routing complexity are the dominant constraints. For new parallel-interface designs, compare total acquisition latency, reference accuracy, input bandwidth, clock requirements, and receiver timing rather than selecting solely by nominal sampling rate.

대체품과의 비교

파라미터 이 제품 ADS7831IPU
Package 28-pin PDIP 28-pin PDIP
Brand Texas Instruments Texas Instruments
Resolution 12 bit 12 bit
Number of Channels 1 channel 1 channel
Sampling Rate 600 kSPS 600 kSPS
Input Range ±2.5 V ±2.5 V
Supply Voltage ±5 V ±5 V
SINAD 69 dB minimum at 250 kHz input 69 dB minimum at 250 kHz input
Input Bandwidth 15 MHz at −3 dB 15 MHz at −3 dB
Output Interface 12-bit parallel, 2's-complement binary 12-bit parallel, 2's-complement binary

주요 차별점

  • Deterministic parallel conversion interface (vs ADS7831IPU)
  • Single-cycle conversion rate suited to deterministic acquisition (vs ADS7831IPU)
  • Integrated complete conversion front end (vs ADS7831IPU)

설계 노트

Route the analog input directly to the converter and keep the surrounding front end away from clock and parallel-output nets. Place input, supply, and reference capacitors at the pins specified in the manufacturer datasheet. Use a continuous ground reference under the device where the package and board construction permit, and return analog and digital currents through controlled paths so switching-node energy does not share a narrow trace with the input or reference node.

Do not treat the 600 kSPS conversion rate as permission to place an arbitrary source directly on the input. Confirm that the source impedance, acquisition time, and output impedance satisfy the settling requirements for 12-bit accuracy. Also verify the distinction between the 15 MHz analog bandwidth and the 600 kSPS sampling rate. An input filter must preserve required signal bandwidth while limiting out-of-band noise.

Provide the specified ±5 V supplies with separate, low-impedance decoupling at the power pins and observe all common-mode and sequencing limits in the manufacturer datasheet. Reference and supply disturbances can appear directly as gain or offset errors, especially when converting small bipolar signals. Check the reference startup behavior, bypass network, and power-supply rejection over the operating frequency range rather than relying only on the nominal conversion rate.

Use a controlled clock source and route clock traces away from the analog input and reference nodes. The parallel outputs are edge-driven signals, so their settling must be included in the receiver timing budget. Match receiver thresholds and trace loading appropriately, use termination only when required by the actual edge rate, and avoid long stubs between the converter and capture logic. The 28 output connections also require adequate grounding and decoupling around the receiving device.

규정 준수 정보

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
무연
Unknown
무할로겐
Unknown
분쟁 광물
Unknown

The operating temperature range indicates a commercial or industrial-temperature application rather than an automotive-qualified product. Confirm current environmental-material declarations from the manufacturer product documentation before procurement.

관련 검색

ADS7831P datasheet ADS7831P datasheet pdf ADS7831P pinout ADS7831P specifications ADS7831P application circuit ADS7831P equivalent ADS7831P replacement ADS7831P cross reference ADS7831P vs ADS7831IPU ADS7831P 600 kSPS ADC ADS7831P 28-pin PDIP Texas Instruments ADS7831P ADS7831P price ADS7831P stock ADS7831P schematic

관련 부품 & 용어

Texas Instruments ADS7831P ADS7831IPU ADS7831 analog-to-digital converter ADC successive-approximation ADC parallel-output ADC data-converter IC sample-and-hold 12-bit resolution 600 kSPS SINAD 2's-complement binary ±2.5 V input ±5 V supply 15 MHz bandwidth 28-pin PDIP PDIP package through-hole package CMOS data acquisition process control sensor interface instrumentation
빠른 견적 RFQ
상세 정보를 모두 입력하십시오 — 영업팀이 24시간 이내에 답변드립니다
부품 번호 제조사 패키지 QTY 목표 가격 합계
✓
견적이 제출되었습니다!

24시간 이내에 이메일로 답변드리겠습니다

1
RFQ 제출됨
2
견적 접수됨
3
주문 완료
4
결제
5
배송됨
6
배송 완료
RFQ 상세 보기