AT90USB162-16AU - 16MHz USB AVR MCU | Microchip Technology
MPN: AT90USB162-16AU ✓ 啟用中AT90USB162-16AU 概覽
An 8-bit microcontroller is a compact embedded-control platform that combines a processor core, nonvolatile program memory, working memory, peripheral interfaces, and general-purpose input/output in one integrated circuit. The AT90USB162 belongs to the AVR 90USB family, where the AVR-enhanced RISC architecture executes instructions efficiently and the integrated USB interface allows a product to connect directly as a USB peripheral without a separate USB controller.
The AT90USB162-16AU provides 16 KB of ISP flash with read-while-write capability, 512 bytes of EEPROM, and 512 bytes of SRAM. Its peripheral set includes two flexible timer/counters with compare and PWM functions, a USART, SPI, a programmable watchdog timer with an internal oscillator, and 22 general-purpose I/O lines. A 16 MHz operating speed supports deterministic control and USB peripheral tasks in compact embedded products.
Its architecture combines the AVR processing core with dedicated USB functionality and conventional serial interfaces. Read-while-write flash permits program-memory access during supported operation, while the EEPROM provides nonvolatile parameter storage and SRAM supports temporary working data. The wide 2.7 V to 5.5 V supply range permits operation from common 3.3 V and 5 V rails, while USB connectivity reduces the component count required for a USB-connected peripheral.
Typical applications include USB human-interface devices, data-acquisition equipment, medical-device interfaces, industrial automation controllers, and service-oriented USB peripherals. The integrated USB controller is especially useful for keyboard, mouse, control-panel, diagnostic-interface, and configuration adapters where compactness, low power, and direct host connectivity are important.
The 32-pin TQFP footprint requires careful fanout between the dense peripheral pins and the external USB, clock, decoupling, and programming connections. Place the required input and output capacitors close to the device, maintain the USB signal path as a short controlled-impedance route, and verify the board against the manufacturer pin-description table and reference design before fabrication.
This product page combines device specifications, application guidance, package information, and a verified same-footprint alternative assessment. It also identifies the design constraints that matter most when implementing the AT90USB162-16AU in a USB-enabled embedded system.
直接替換替代品,適用於 AT90USB162-16AU — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: AT90USB162-16AU (相同外形與佔位) — 差異在於 General-Purpose I/O Lines, General-Purpose Working Registers, Package, Programming Interface, Serial Interfaces.
AT90USB162-16MU
✅ 直接替換聯絡詢價
查看資料表 →AT90USB162-16AU 最大額定值與電氣特性
| Product Type | 8-bit AVR RISC microcontroller with USB controller |
| Maximum Clock Speed | 16 MHz |
| Program Memory | 16 KB ISP flash |
| Program Memory Organization | 16K x 8 bits |
| Flash Read-While-Write | Supported |
| EEPROM | 512 bytes |
| Static RAM | 512 bytes |
| General-Purpose I/O Lines | 22 lines |
| General-Purpose Working Registers | 32 registers |
| Timer/Counter Count | 2 timers/counters with compare modes and PWM |
| Serial Interfaces | USB, USART, and SPI |
| Watchdog Timer | Programmable with internal oscillator |
| 工作電源電壓 | 2.7 V to 5.5 V |
| 工作溫度範圍 | -40 °C to +85 °C |
| 封裝 | 32-pin TQFP, 7 mm x 7 mm |
| 安裝類型 | Surface mount |
| Programming Interface | In-system programming |
AT90USB162-16AU 32-pin tqfp, 7 mm x 7 mm 腳位配置指南
AT90USB162-16AU(32-pin tqfp, 7 mm x 7 mm 封裝)的腳位配置。 此數位 IC 包含 GPIO、通訊介面(UART、SPI、I2C)與電源腳位。替代腳位功能與配置選項請參閱製造商資料表。對嵌入式系統設計與 PCB 佈局至關重要。
無詳細腳位定義資料: AT90USB162-16AU.
請參閱 資料表 以查看完整腳位配置。
典型應用
AT90USB162-16AU 適用於 6 應用s: USB Human-Interface Devices, Industrial USB Data Acquisition, Medical Device Interfaces, USB Configuration and Programming Tools, USB Control Panels, USB Connected Sensor Hubs.
USB Human-Interface Devices
The AT90USB162-16AU fits compact USB HID products because its 16 MHz AVR core can service USB transactions while its 22 general-purpose I/O lines support buttons, indicators, encoders, and status LEDs. The integrated USB controller removes the need for a separate host-interface IC, while 16 KB of ISP flash and 512 bytes of EEPROM provide space for device firmware, configuration, and identifiers. A keyboard, control panel, mouse, or custom input device can use SPI or USART-connected sensors when more than the general-purpose I/O can accommodate. The 32-TQFP footprint also keeps the assembly compact enough for slim accessories. Firmware should enumerate as the intended HID class, implement suspend and resume behavior, and validate the bus-powered current budget before production release.
推薦
Industrial USB Data Acquisition
The AT90USB162-16AU is well suited to compact industrial data-acquisition modules because it combines USB connectivity with SPI, USART, two timer/counters, and 22 general-purpose I/O lines. The 16 MHz operating speed supports responsive sampling and control tasks, while 512 bytes of SRAM accommodates transient acquisition data and 512 bytes of EEPROM can retain calibration or configuration parameters. A sensor front end using SPI can share the same device with discrete digital controls, and PWM outputs can support excitation or actuator functions. Industrial deployments should use the 2.7 V to 5.5 V operating range appropriately, isolate externally connected signals, and validate conducted and radiated emissions because the module places a high-speed digital USB interface beside precision analog inputs.
推薦
Medical Device Interfaces
The AT90USB162-16AU can serve as the USB communication and supervisory controller in a compact medical-device interface. Its integrated USB controller provides a direct path to a host computer, while the USART and SPI support sensors, displays, isolation components, and service interfaces. The 16 KB ISP flash is sufficient for a focused communication, alarm, and control application, and the 512-byte EEPROM can hold nonvolatile setup values without occupying the limited SRAM budget. For medical equipment, developers should keep the patient-connected circuitry electrically separated, define safe firmware-restart behavior, and validate enumeration recovery after power interruptions. USB suspend handling and brownout behavior are also critical because they determine whether the interface returns safely to service after a cable or power fault.
推薦
USB Configuration and Programming Tools
The AT90USB162-16AU is appropriate for USB configuration adapters, field-programming tools, and equipment-control interfaces where a host must exchange commands with embedded circuitry. The AVR core, USART, SPI, timer/counters, and watchdog support simultaneous protocol handling and reliable recovery from communication faults. Sixteen kilobytes of ISP flash can hold a bootloader and application, and 512 bytes of EEPROM can store device identity or calibration constants. A production configuration tool should use stable USB descriptors, controlled vendor-specific requests, and a timeout that resets stalled transfers. The programmable watchdog is useful during long operations, but it must be serviced only after meaningful progress so repeated protocol failures cannot create a continuous reset loop.
推薦
USB Control Panels
A compact control panel built around the AT90USB162-16AU can combine USB communication, local button handling, status indication, and actuator control in one device. Its 22 general-purpose I/O lines leave substantial capacity for panel inputs and outputs, while the two timer/counters with PWM support can dim indicators or drive small loads. The 16 MHz clock provides responsive panel behavior, and the integrated USB controller allows the panel to present a standard HID or vendor-specific interface to a host. Layout should preserve short USB routing and provide separate return paths for switching currents, particularly when PWM outputs drive LEDs. Firmware should debounce physical inputs, report state changes efficiently, and define safe output states when the host disconnects or the USB bus enters suspend.
推薦
USB Connected Sensor Hubs
The AT90USB162-16AU supports small USB-connected sensor hubs that consolidate digital measurements and expose them to a host computer. SPI is available for high-speed sensor or storage components, USART supports slower serial devices, and the 22 I/O lines provide discrete digital channels. At 16 MHz, the MCU can coordinate timed sampling using its two timer/counters, while 512 bytes of SRAM handles short data buffers and 512 bytes of EEPROM stores node information. A practical hub should batch samples to limit USB transaction overhead, include timeout handling for absent sensors, and account for the cumulative current of all attached loads. Galvanic isolation and sensor-specific protection must be designed separately from the low-voltage microcontroller circuitry.
推薦
推薦產品摘要
工程參考資料,適用於 AT90USB162-16AU — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | AT90USB162-16MU |
|---|---|---|
| Brand | Microchip Technology | Microchip Technology |
| Package | 32-TQFP (7x7) | 32-TQFP (7x7) |
| Architecture | 8-bit AVR RISC | 8-bit AVR RISC |
| Maximum Clock Speed | 16 MHz | 16 MHz |
| Flash Memory | 16 KB ISP flash | 16 KB ISP flash |
| EEPROM | 512 bytes | 512 bytes |
| Static RAM | 512 bytes | 512 bytes |
| General-Purpose I/O Lines | 22 lines | 22 lines |
| Serial Interfaces | USB, USART, and SPI | USB, USART, and SPI |
| Operating Supply Voltage | 2.7 V to 5.5 V | 2.7 V to 5.5 V |
| Timer/Counter Count | 2 | 2 |
| Ordering Configuration | AT90USB162-16AU | AT90USB162-16MU; package/handling code differs |
主要差異化特點
- Integrated USB avoids a separate host-interface controller (對比AT90USB162-16MU)
- Balanced embedded memory configuration (對比AT90USB162-16MU)
- Peripheral coverage for compact USB products (對比AT90USB162-16MU)
設計說明
Use the manufacturer AT90USB162 pin-description table as the authoritative assignment for power, ground, USB, clock, reset, programming, and I/O nets. Keep the D+ and D+ connector path short and pair it with a continuous ground reference, avoiding stubs beneath the device. Place the decoupling network at the relevant supply pins and preserve a low-impedance return path to the USB connector so high-frequency common-mode current does not cross sensitive analog or sensor areas.
Plan the power tree for both 3.3 V and 5 V operating environments because the AT90USB162-16AU supports a 2.7 V to 5.5 V supply. Apply the manufacturer’s recommended input and output capacitance at the device, including the required effective capacitance for USB operation, and verify startup behavior across the full supply range. If the design includes USB-powered and externally powered states, define a deterministic transition sequence so the controller does not brown out during cable insertion or removal.
Do not substitute the AT90USB162-16MU solely because it appears in comparison listings. Confirm that its ordering code matches the required 32-TQFP assembly method, temperature class, and production packing process. Also verify the final USB firmware configuration, boot mode, clock setup, and watchdog behavior. A package or ordering-code mismatch can prevent assembly even when the processor, memory size, and USB feature set appear equivalent.
合規資訊
The Microchip Technology AT90USB162 product page and device listing do not state the requested compliance details on this page. Use the current manufacturer product documentation and declarations for production qualification.