ATTINY24A-SSF - 20MHz 8-Bit AVR MCU | Microchip Technology
MPN: ATTINY24A-SSF ✓ 啟用中ATTINY24A-SSF 概覽
A microcontroller is a programmable semiconductor that combines a processor core, nonvolatile program memory, working memory, and peripherals on one integrated circuit. The ATtiny24A belongs to Microchip's picoPower AVR family and uses an enhanced RISC architecture with throughput approaching 1 MIPS per MHz. This combination makes it suitable for compact embedded-control products that need more processing capability than a basic logic controller but do not require a larger general-purpose MCU.
The ATTINY24A-SSF provides 2 KB of in-system programmable Flash for firmware, 128 B of SRAM for volatile data, and 128 B of EEPROM for nonvolatile settings. Its 12 I/O lines support digital interfaces, timers, and ADC inputs, while the 10-bit ADC measures up to eight analog channels. The dual 8-bit and 16-bit timer architecture provides flexible event counting, delay generation, and PWM output for dimming, motor control, and proportional control functions.
Its communication and programming architecture follows the AVR ecosystem. The device supports In-Circuit Serial Programming and can use an 8-pin SIL debug connector through the MPLAB Snap programmer, with two I/O pins and the reset line carrying the programming interface. The 20 MHz maximum clock rate provides ample instruction throughput for embedded logic, sensor acquisition, and local actuator control, although the 2 KB program-memory limit requires compact firmware and careful code organization.
Typical applications include low-cost sensor nodes, LED dimming controllers, small motor controllers, industrial timers, compact battery-powered instruments, and automotive accessories. The ADC enables direct interface to resistive sensors, while the PWM channels can drive lamps, fans, or small solenoids. A system requiring more flash memory can evaluate the pin-compatible ATtiny24A family variants when the selected suffix maintains the required package, temperature grade, and production configuration.
PCB design should reserve the power pins for a short, low-impedance supply path and place the decoupling capacitor close to the device. Use the manufacturer pin-description table when assigning multiplexing functions to PA and PB pins, and preserve access to the programming interface so firmware updates and debugging remain practical after assembly.
This page organizes the key electrical, memory, timing, and package characteristics of the ATTINY24A-SSF with practical application guidance, programming considerations, and a parameter-by-parameter comparison of compatible ATtiny24A ordering options. It is intended to help engineers validate footprint, functionality, lifecycle, and sourcing requirements before committing the MCU to an embedded design.
直接替換替代品,適用於 ATTINY24A-SSF — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
ATTINY24A-SSFR
✅ 直接替換📋 參考替代品(不在目錄中)
ATTINY24A-SSU
✅ 直接替換📋 參考替代品(不在目錄中)
ATTINY24A-SSUR
✅ 直接替換📋 參考替代品(不在目錄中)
ATTINY24A-SSF 最大額定值與電氣特性
| Product Type | 8-bit RISC Flash Microcontroller |
| Architecture | AVR enhanced RISC |
| CPU Family | AVR ATtiny |
| 最大時脈頻率 | 20 MHz |
| Flash Memory | 2 KB |
| Flash Organization | 1K x 16 bits |
| EEPROM | 128 bytes |
| SRAM | 128 bytes |
| General-Purpose I/O Lines | 12 |
| General-Purpose Working Registers | 32 |
| ADC Resolution | 10 bits |
| ADC Channels | 8 channels |
| Timer/Counter 0 | 8-bit with 2 PWM channels |
| Timer/Counter 1 | 16-bit with 2 PWM channels |
| Program Memory Type | In-System Programmable Flash |
| Programming Interface | ICSP with 8-pin SIL connector interface |
| Operating Supply Range | 1.8 V to 5.5 V |
| 封裝 | 14-pin SOIC |
| 安裝類型 | Surface mount |
ATTINY24A-SSF 腳位配置
| 腳位 1 | PB0/MOSI/DI/SDA/OC1A/PCINT0 — Multiplexed port-B input/output, timer output, serial interface, and external interrupt |
| 腳位 2 | PB1/MISO/DO/SCL/OC1B/PCINT1 — Multiplexed port-B input/output, timer output, serial interface, and external interrupt |
| 腳位 3 | PB2/OC0B/INT0/PCINT2 — Multiplexed port-B input/output, timer output, external interrupt, and pin-change interrupt |
| 腳位 4 | PB3/MOSI/DI/SDA/OC1A — Multiplexed port-B input/output, timer output, and serial interface |
| 腳位 5 | PA0/ADC0/AREF — Port-A input/output and ADC channel 0 |
| 腳位 6 | PA1/ADC1/AIN0 — Port-A input/output, ADC channel 1, and analog input |
| 腳位 7 | PA2/ADC2/AIN1 — Port-A input/output, ADC channel 2, and analog input |
| 腳位 8 | PA3/ADC3/T0 — Port-A input/output, ADC channel 3, and timer input |
| 腳位 9 | GND — Ground connection |
| 腳位 10 | PA4/ADC4/T1 — Port-A input/output, ADC channel 4, and timer input |
| 腳位 11 | PA5/ADC5/T2 — Port-A input/output, ADC channel 5, and timer input |
| 腳位 12 | PA6/ADC6 — Port-A input/output and ADC channel 6 |
| 腳位 13 | PA7/ADC7 — Port-A input/output and ADC channel 7 |
| 腳位 14 | VCC — Supply voltage connection |
典型應用
ATTINY24A-SSF 適用於 6 應用s: Compact Industrial Sensor Node, LED Dimming Controller, Small Motor and Fan Controller, Programmable Timer and Sequencer, Battery-Powered Measurement Instrument, Automotive Accessory Controller.
Compact Industrial Sensor Node
The ATTINY24A-SSF fits compact industrial sensor nodes because its 8-channel, 10-bit ADC can sample several analog inputs while the 20 MHz AVR core handles filtering, threshold decisions, and data formatting. Its 2 KB Flash supports compact firmware, and 128 B of SRAM provides working space for acquisition and control state. Place the device between resistive sensors and a communication interface, then use the ADC reference and port multiplexing from the manufacturer data sheet. The main constraint is code and buffer capacity: designs requiring extensive calibration tables, history logging, or multiple protocol stacks should use a larger ATtiny family member.
推薦
LED Dimming Controller
The ATTINY24A-SSF is well suited to LED dimming because its timer/counters provide two PWM channels each in 8-bit and 16-bit configurations. The 20 MHz clock allows accurate PWM generation, while the 10-bit ADC can monitor a current-sensed or potentiometer input for dimming control. Firmware can map an analog command to PWM duty cycle and handle fade sequencing or fault limits. Confirm timer prescaler and PWM frequency against the LED driver topology, and account for the ATtiny24A's limited 2 KB Flash when adding lighting effects.
推薦
Small Motor and Fan Controller
The ATTINY24A-SSF can control small motors, fans, and solenoids where PWM speed adjustment and compact firmware are more important than high processing throughput. Two PWM outputs from each timer/counter support proportional actuator commands, while the ADC can monitor current or supply voltage for protection. A practical design uses a transistor or MOSFET driver rather than driving a load directly from an I/O pin. Add stall, overtemperature, and overcurrent handling in firmware, and verify the 20 MHz timer configuration against the required PWM frequency and duty-cycle resolution.
推薦
Programmable Timer and Sequencer
The ATTINY24A-SSF fits programmable timers and sequencing controls because it combines 8-bit and 16-bit timer/counters with internal and external interrupts. The 16-bit timer provides a longer count range, while the 8-bit timer can divide frequency, generate delays, or provide PWM. Firmware can implement multistep sequences using the interrupt vectors and general-purpose I/O, and the ADC can optionally verify a process variable. The 2 KB Flash limit favors compact state machines rather than elaborate user interfaces, while 128 B of SRAM supports a modest working schedule.
推薦
Battery-Powered Measurement Instrument
The ATTINY24A-SSF supports battery-powered measurement instruments where an 8-bit processor, 10-bit ADC, and low pin count reduce board complexity. Its operating range of 1.8 V to 5.5 V allows design around common low-voltage cells or regulated supplies, and the AVR sleep modes can reduce energy between measurements. Use the ADC for slowly changing analog inputs and the PWM outputs for reference or excitation control. Validate active current, sleep current, and startup behavior against the battery budget because total energy depends on firmware duty cycle and measurement rate.
推薦
Automotive Accessory Controller
The ATTINY24A-SSF can serve as a compact controller for selected automotive accessories when the exact suffix, qualification status, and operating requirements are verified. The 20 MHz AVR core, 12 I/O lines, ADC, and PWM channels are useful for switches, lamps, sensor interfaces, and small actuators. A robust design must include transient protection, valid automotive-grade decoupling, watchdog and fault recovery, and qualification review of the specific ATTINY24A ordering code. Do not assume that family-level automotive positioning applies to every package or temperature suffix without checking the manufacturer's qualification documentation.
推薦
推薦產品摘要
工程參考資料,適用於 ATTINY24A-SSF — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | ATTINY24A-SSFR | ATTINY24A-SSU | ATTINY24A-SSUR |
|---|---|---|---|---|
| Package | 14-SOIC | 14-SOIC | 14-SOIC | 14-SOIC |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Maximum Clock Frequency | 20 MHz | 20 MHz | 20 MHz | 20 MHz |
| Flash Memory | 2 KB | 2 KB | 2 KB | 2 KB |
| EEPROM | 128 bytes | 128 bytes | 128 bytes | 128 bytes |
| SRAM | 128 bytes | 128 bytes | 128 bytes | 128 bytes |
| General-Purpose I/O Lines | 12 | 12 | 12 | 12 |
| ADC | 8-channel, 10-bit | 8-channel, 10-bit | 8-channel, 10-bit | 8-channel, 10-bit |
| Operating Voltage | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V |
主要差異化特點
- Combines an 8-channel ADC with dual timer banks in a compact 14-pin MCU (對比ATTINY24A-SSFR)
- Offers the same 20 MHz core and 2 KB memory footprint across the compared ordering options (對比ATTINY24A-SSU)
- Supports compact AVR embedded control with 12 I/O lines (對比ATTINY24A-SSUR)
設計說明
Place the supply decoupling capacitor immediately across the VCC and GND pins, with the shortest possible ground return and no test pads or routing breaks in the current path. Keep the 14-SOIC footprint unobstructed on both sides of the board where possible. Route the ICSP signals away from switching nodes and analog inputs to reduce programming-pulse and switching-transient coupling into sensitive measurements.
Use the manufacturer pin-description table before assigning PA and PB functions because the 12 I/O pins are multiplexed among ADC inputs, timer inputs, interrupt inputs, USI signals, and PWM outputs. Confirm that the selected peripheral function does not conflict with a second subsystem. For analog measurements, provide a quiet reference path and keep the ADC input traces short, away from PWM and motor-driver switching nodes.
The 2 KB Flash limit is the most common design constraint, so estimate firmware and bootloader requirements before finalizing the MCU. Reserve program memory for future fixes, avoid relying on large runtime libraries, and account for boot-lock and application sections when configuring fuses. Also verify the required reset level, clock source, brownout behavior, and ICSP access using the ATtiny24A/44A/84A data sheet DS40002269A.
Estimate average consumption from the firmware duty cycle rather than the active-mode current alone. The calculation should use the operating voltage, active current, sleep current, measurement duration, and number of ADC samples per operating cycle. Check that the supply remains within 1.8 V to 5.5 V at the MCU pins during switching transitions, especially when the same source powers motors, LEDs, or other loads.
合規資訊
The ATtiny24 family has been recommended for automotive design by Microchip, but qualification and material-compliance status for the exact ATTINY24A-SSF ordering code were not established. Verify current product documentation before production release.